USGS Science⌕ Search

FIND YOUR NEXT DISCOVERY

Results for “Renewable Energy”

Original records, connected by a shared subject.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

59 recordsLinked to original sources
USGS2026

Geothermal district energy systems coupled with seasonal underground thermal energy storage: A U.S. techno-economic screening by climate and geology

In the United States, cooling-dominated commercial building loads can cause geothermal heat pump-based district energy systems to accumulate a long-term subsurface thermal imbalance, motivating the incorporation of seasonal underground thermal energy storage. We developed a transferable workflow to evaluate geothermal district systems that pair ground heat exchangers with seasonal underground thermal energy storage. Using standardized hourly loads for seven commercial buildings and a uniform cost framework, we simulated ten U.S. cities with a physics-based ground heat exchanger model, subsurface storage simulations, and economic assessment to isolate the roles of climate and hydrogeology. In cooling-dominated cities, underground thermal energy storage supplied the majority of annual cooling, cutting electricity use and summer peaks substantially while achieving levelized costs comparable to or below conventional chiller-boiler plants. In cooler climates, the storage share shrunk, required borefield size and costs rose, and levelized cost of energy increased nearly linearly with declining underground thermal energy storage fraction, indicating storage fraction as the primary economic lever. Sensitivity analysis showed capital risk dominated by borefield drilling and surface heating, ventilation, and air-conditioning and piping, with underground thermal energy storage costs secondary. This workflow provides a transparent foundation for site-specific design and screening of next-generation geothermal district energy systems.

Arizona, Illinois, Maryland, Michigan, Mississippi↗
USGS2025

A probabilistic assessment methodology for the evaluation of geologic energy storage capacity—Natural gas storage in depleted hydrocarbon reservoirs

The need for energy storage, particularly underground, where capacity and duration may far exceed battery storage technologies, is especially relevant given the increasing demands for reliable power alongside the development of intermittent renewable electricity sources. Geologic energy storage facilities already exist, and expanded use would enable storing gases such as methane and hydrogen. In 2018, a National Academies of Sciences, Engineering, and Medicine report, “Future Directions for the U.S. Geological Survey's Energy Resources Program,” recommended that the U.S. Geological Survey (USGS) prioritize assessing underground energy storage in geologic formations in the United States. The U.S. Geological Survey has since developed a methodology for assessing natural gas storage capacities in depleted hydrocarbon reservoirs on a national scale. The methodology introduced in this report prescribes three approaches for calculating gas storage capacity. This methodology relies on the availability of input data, including cumulative hydrocarbon production records, reservoir petrophysical properties, and reservoir pressure data. Assessment inputs can be obtained from public, State-level databases and propriety national-scale databases, although the use of analogs could be warranted for estimating input parameters. Probabilistic assessment results are aggregated to play, petroleum province, regional, and national scales. The steps defined in this report are demonstrated on the Michigan Basin Province, which includes the Mississippian Sandstone Gas Play and the Clinton Structural Play. This methodology could be used to systematically and consistently assess hydrocarbon plays and provinces for natural gas storage capacity across the United States.

Michigan↗
USGS2025

Estimating the hypothetical endowment of critical minerals and other commodities in porphyry copper mine waste in the Four Corners states, USA

Society is fundamentally dependent upon commodities that are used in end-use products for the aerospace, defense, energy, telecommunication, and transportation sectors, resulting in centuries of mining to supply these commodities and materials. Waste from these mining operations can remain on the landscape indefinitely, but there is a lack of national understanding of the distribution and scale of such waste features. The renewable energy transition will continue to increase demand for critical minerals and will result in increasing volumes of mine waste on the Earth’s surface. Reprocessing mine waste can reduce environmental risks and recover needed commodities to match growing demand for societal growth. Therefore, understanding the approximate abundance of commodities that may be available for recovery within mine waste features can be an important piece of domestic critical mineral supply.

Arizona, Colorado, New Mexico, Utah↗
USGS2025

Evolution of permeability and strength recovery of shear fracture under hydrothermal conditions

Geothermal energy is a clean and renewable resource that depends on the ability to move water through hot rock. In many locations, the ability to move water through rock requires the presence of extensive natural or human-made systems of fractures. However, these fracture systems are influenced by a variety of complex processes that occur at the temperature and pressure conditions found in geothermal reservoirs. To make geothermal systems more efficient, it is important to understand how these fractures evolve over time in response to these processes. This study explored how fractures in rock change under high-temperature and pressure conditions, like those found in geothermal reservoirs, through laboratory experiments and numerical simulations. In general fractures, tend to close due to pressure from the surrounding rock preventing the flow of water. One set of laboratory experiments revealed that fractures in granitic rock can weaken over time at elevated temperatures. These weak fractures can then slip slowly potentially keeping the fracture open for a longer period. This study also showed that at the highest temperature examined (250 °C) large differences between the chemical composition of the rock and the fluid moving through it could improve water flow temporarily likely due to the water dissolving parts of the rock. Flow rate predicted by models shows overall good agreement with the flow rate measured in our experiments but with some long time-scale variations that may be due to mechanical wear of the fracture surface. A second set of experiments found that, over the temperature range examined, the closure of fractures was caused by brittle failure driven by high stresses at points where fracture surfaces were in contact. This result suggests that fracture closure in geothermal reservoirs could be counteracted by maintaining high pore pressures. Additionally, we also tested a new method using electrical resistance to measure fracture closure in controlled systems with high precision.

Final Technical Report↗
USGS2026

Key minerals in energy transmission

The electrical grid relies on minerals with unique properties to transform, transmit, and convert electricity. Transmission needs are growing—to support the expansion of data centers and link diverse energy resources into the grid. This expansion will require greater quantities of minerals. Although some minerals are produced in the United States, the United States relies on imports for others. This infographic shows the key minerals that support energy transmission, and how reliant the United States is on imports for these minerals.

General Information Product↗
USGS2026

Uncertainty quantification of geologic energy storage in depleted gas reservoirs using material balance equations embedded in a hierarchical errors-in-variables model

The storage potential for gas in geologic settings, such as depleted hydrocarbon reservoirs and solution-mined salt caverns, is becoming salient to future energy infrastructure planning. Technologies such as carbon capture, utilization, and storage, carbon dioxide-enhanced oil recovery, and natural gas and hydrogen storage help meet growing energy demands, reduce carbon emissions to meet climate goals, and provide energy security amid geopolitical uncertainties. Therefore, estimates of underground gas storage capacity could be useful for efficiently navigating the energy transitions. Material balance is a fundamental method in reservoir engineering for estimating original gas in place and potential storage capacity at the scale necessary for national assessments of subsurface pore space resources. However, the deterministic method cannot accommodate multiple data sources or quantify uncertainty in predictions. In this study, a method that embeds material balance equations within a hierarchical errors-in-variables model is proposed which allows the estimation of the distributions of reservoir properties needed for assessments. Uncertainties associated with these reservoir properties have traditionally been expert-elicited, whereas the uncertainty estimates from the proposed models are data-driven. Capacity and uncertainty estimates can be used in a probabilistic resource assessment, supplementing information traditionally used by assessors or even replacing this expert elicitation step when data are unavailable. Various regression models are compared in a case study of the Michigan Basin, a large contributor to the United States’ current natural gas storage capacity. In particular, errors-in-variables models help ameliorate regression dilution and can quantify uncertainty in predictions of pressure in addition to storage capacity. Overfitting is addressed by quantifying generalization error and model averaging in simple and stratified cross-validation against reported working gas capacity, representing the varying quality and quantity of available data. Incorporating a statistical framework into existing numerical methods in reservoir engineering can improve the quality of estimation, and in particular, this method brings rigor to uncertainty quantification as part of a larger effort by the U.S. Geological Survey to assess domestic energy gas storage resources in depleted hydrocarbon reservoirs.

Mathematical Geosciences↗
USGS2025

Evaluating the potential of co-located non-petroleum energy resources in the Gulf Coast using play fairwayaAnalysis

Geological resources critical to the energy transition, such as sedimentary geothermal, carbon storage potential, and lithium in brines, commonly struggle for economic feasibility as stand-alone developments but can have greater viability when the potential for more than one of these resources exist within the same reservoir or stacked in different stratigraphic intervals. There may also be instances where development of one resource inhibits development of others and decisions need to be made on how to best prioritize the use of those resources in the subsurface. Subsurface data sets were analyzed and integrated to evaluate the distribution of non-petroleum energy and related resources in the onshore and nearshore U.S. Gulf Coast. Temperature, pressure, brine composition (lithium content), and reservoir quality data for thirty-four depositional units have been compiled and visualized to high-grade areas where multiple resource opportunities likely coexist. For sedimentary geothermal, possible resource areas are defined as low potential (<90°C), moderate potential (90–150°C), and high potential (>150°C). For CO 2 storage, high potential areas exhibit supercritical CO 2 conditions less than 80% of the fracture gradient. Areas with pore pressure between 80% and 100% of the fracture gradient are considered to exhibit moderate potential and areas where the fracture gradient is equal to or greater than 100% are assigned low potential. Lithium resources in brines were defined by lithium concentrations as low potential (<100ppm), moderate potential (100-200ppm), or high potential (>200ppm). Reservoir quality affects the viability of all three of these resources and is evaluated using depositional environment maps of each unit. The resulting play fairway maps can be used for regional scale screening evaluations of these resources and to identify areas of interest where more detailed, prospect-scale studies can be undertaken.

Gulf Coast↗
USGS2026

Neutron scattering reveals fractionation of natural gas mixtures in unconventional petroleum reservoir pores: Perspectives on energy resource recovery and storage

In unconventional petroleum reservoirs hydrocarbon fluids are hosted by both mineral and organic matter pores. These pores can have diameters that range from microns to less than a single nanometer and, for unconventional reservoirs, there is evidence that small pores ( <20 nm diameter) may constitute a large proportion of the available space. Understanding subsurface volumes and how fluids behave in them can be helpful for predicting hydrocarbon production and storage in the subsurface. One area with knowledge gaps regarding hydrocarbon behavior in small pores is the possibility for mixtures to fractionate (i.e., unmix) based on pore size or pore type. Mixture fractionation as a function of pore size could impact recovery of hydrocarbons, drive compositional shifts during production, and limit fluid storage within candidate reservoirs. To investigate natural gas fractionation in small geologic pores, we applied total neutron scattering to probe methane-ethane mixtures at reservoir pressures (up to ≈30 MPa) and temperature (60°C) within a sample from the Upper Cretaceous Niobrara Formation. Neutron scattering data reveal only minor fractionation occurs between methane and ethane in 20-nm diameter sample mesopores. Increased fractionation is observed for sample micropores, with up to 72% (±1% at 1-sigma) methane found in 2 nm diameter pores following injection of a 50%-50% methane-ethane mixture. These data provide rarely available direct experimental observations of hydrocarbon mixture behavior under nanoconfinement in a sample from an important unconventional petroleum reservoir. Our results are discussed in the context of evaluating hydrocarbon resources in unconventional reservoir meso- and micropores, reconciling observed gas composition changes during production, and more broadly, understanding subsurface pore volumes within an energy storage framework.

Fuel↗
USGS2025

The 1912 Ms 7.2 earthquake in the Denali region of central Alaska

The 2002 M w 7.9 earthquake in central Alaska ruptured 340 km on three faults—Susitna Glacier thrust fault, Denali fault, Totschunda fault—crossing both the Richardson Highway and the Alaska Pipeline. Its occurrence prompted renewed interest in historical large earthquakes that possibly originated on the Denali fault. One of these earthquakes was a M s 7.2 event on July 7, 1912, which we revisit with two approaches: (1) probabilistic relocation of the epicenter using globally recorded arrival times, and (2) compilation and reassessment of shaking intensity reports to estimate a macroseismic epicenter. Our preferred instrumental epicenter is west of the Parks Highway and in agreement with the maximum‐reported shaking, which was from the Parker–Browne expedition of Denali. We also relocated a M s 6.4 aftershock, whose epicenter is 11 km from the mainshock. Candidate faults for the 1912 earthquake include the Denali fault, the McLeod Creek thrust fault, and the Kantishna Hills thrust fault. Future analysis of active faults, paleoseismic results, 1912 instrumental data, and 1912 felt reports may help in interpreting the fault and mechanism of the 1912 earthquake.

Alaska↗
USGS2000

Regional evaluation of evapotranspiration in the Everglades

Nine sites in the Florida Everglades were selected and instrumented for collection of data necessary for evapotranspiration-determination using the Bowen-ratio energy-budget method. The sites were selected to represent the sawgrass or cattail marshes, wet prairie, and open-water areas that constitute most of the natural Everglades system. At each site, measurements necessary for evapotranspiration (ET) calculation and modeling were automatically made and stored on-site at 15- or 30-minute intervals. Data collected included air temperature and humidity at two heights, wind speed and direction, incoming solar radiation, net solar radiation, water level and temperature, soil moisture content, soil temperature, soil heat flux, and rainfall. Data summarized in this report were collected from January 1996 through December 1997, and the development of site-specific and regional models of ET for this period is described. Latent heat flux is the energy flux density equivalent of the ET rate. Modified Priestley-Taylor models of latent heat flux as a function of selected independent variables were developed at each site. These models were used to fill in periods of missing latent heat flux measurement, and to develop regional models of the entire Everglades region. The regional models may be used to estimate ET in wet prairie, sawgrass or cattail marsh, and open-water portions of the natural Everglades system. The models are not applicable to forested areas or to the brackish areas adjacent to Florida Bay. Two types of regional models were developed. One type of model uses measurements of available energy at a site, together with incoming solar energy and water depth, to estimate hourly ET. This available-energy model requires site data for net radiation, water heat storage, and soil heat flux, as well as data for incoming solar radiation and water depth. The other type of model requires only incoming solar energy, air temperature, and water depth data to provide estimates of hourly ET. The second model thus uses data that are more readily available than the data required for the available-energy model. Computed ET mean annual totals for all nine sites for the 1996-97 period ranged from 42.4 inches per year at a site where the water level is below land surface for several months each year to 57.4 inches per year at an open-water site with no emergent vegetation. Although the density of photosynthetically-active plant leaves has been shown to relate directly to ET in some studies, it does not appear to relate directly to ET in the Everglades, based on comparison of annual ET data with leaf-area index, defined as the Normalized Difference Vegetation Index (NDVI), data from satellite imagery. NDVI and ET appear to be inversely related in the Everglades. The greatest ET rates occurred at open-water sites where the NDVI data indicated the lowest leaf-area index. Among the remaining vegetated sites, there is no clear relation between ET and NDVI, though the highest ET rate corresponded to the lowest NDVI and one of the lowest ET rates corresponded to the highest NDVI value. The variation in ET follows a seasonal pattern, with lowest monthly ET totals occurring in December through February, and highest ET occurring in May through August. The greatest range in monthly ET among all nine sites for the 2-year period occurred at site 3: from 1.81 inches in December 1997 to 6.84 inches in July 1996. A study to compare the Bowen-ratio/energy balance method of ET measurement with the eddy-correlation method was done at one site from June 22, 1998, through September 28, 1998. This comparison indicated that both methods gave comparable values of the Bowen ratio, but there was a considerable difference in available energy measured by the two methods. The mean of all 30-minute measured turbulent heat fluxes from the eddy-correlation apparatus for June 22 through September 29, 1998, was 137.4 watts per square meter, and the mean of the corresponding measured energy was 163.6 watts per square meter, or about 20 percent greater. The disagreement in mean energy fluxes measured by the two methods is problematical and is not fully understood. Although the difference seems to be related to friction velocity, and is practically non-existent at values of friction velocity greater than 0.3 meter per second, the "correctness" of either method cannot be determined with the data available.

Florida↗
USGS2025

Estimated ultimate recovery (EUR) Prediction for Eagle Ford Shale using integrated datasets and artificial neural networks

The estimated ultimate recovery (EUR) is an important parameter for forecasting oil and gas production and informing decisions regarding field development strategies. In this study, we combined site-specific geologic, completion, and operational parameters with the predictive capabilities of machine learning (ML) models to predict EURs of the wells for the Eagle Ford Marl Continuous Oil Assessment Unit. We developed an extensive dataset of wells that have produced from the lower and upper Eagle Ford Shale intervals and reduced the model complexity using principal component analysis. We tested the ML models and estimated the sensitivities of ML-predicted EURs to changes in the values of different input variables. The results of applying the optimized ML model to the Eagle Ford suggest that the approach developed in this study could be promising. The ML estimates of the EURs fit the DCA-based values with an R 2 ~ 0.9 and a mean absolute error of ~36 × 10 3 bbl. In the lower Eagle Ford Shale, the EUR estimates were found to be most sensitive to changes in porosity, net thickness of the interval, clay volume, and the API gravity of the oil; and that in the upper Eagle Ford Shale they were most sensitive to changes in the total organic carbon and water saturation, which suggests that it could be important to consider these parameters in assessing these intervals or close analogs.

Louisiana, Mississippi, Texas↗
USGS2026

Ductile and brittle Rio Grande Rift deformation in Oligocene granite records a two-stage rift history in southern Colorado

The timing and nature of early deformation in the Rio Grande Rift remains poorly constrained. We present evidence for the earliest structural signature of rift extension in the Sangre de Cristo Range, southern Colorado, based on new geologic mapping, structural analysis, rock magnetic data, and thermochronology. These analyses focus on the ~30.0 Ma granite of Chokecherry Canyon, which hosts discrete low-angle mylonitic shear zones and a distributed, gently SW-dipping protomylonitic fabric. Incremental stretching axes, stretching lineations, and Kmax magnetic lineations plunge gently WSW. Quartz microstructures and crystallographic orientations indicate dominantly coaxial strain in the protomylonite and general shear in the discrete shear zones. Quartz c-axis opening-angle thermometry suggests deformation at ~420–540°C. Thermal modeling of ⁴⁰Ar/³⁹Ar K-feldspar data indicates rapid post magmatic cooling below the brittle–plastic transition, supporting shear-zone formation immediately after emplacement. Slow cooling from ~20–13 Ma was followed by renewed rapid cooling at ~13 Ma, interpreted as the onset of extensional exhumation along the Sangre de Cristo Fault System. These results show that extension in the northern Rio Grande Rift was active by ~30 Ma, earlier than previously recognized. We propose a two-stage model for northern Rio Grande Rift evolution: Stage I (30–23 Ma) records ENE–WSW extension localized in low-angle mylonitic shear zones associated with mid-crustal intrusions; Stage II (≤18 Ma) reflects brittle high-angle normal faulting, focused exhumation, and rift narrowing. Stage I magmatism and deformation along the western range front likely established crustal weaknesses that guided later fault development.

Colorado↗
USGS2025

Alteration mapping in granitic gneiss using handheld geophysical and geochemical instruments: Implications for iron oxide-apatite and rare earth elements exploration

The Adirondack Mountains of New York, U.S.A. contain iron oxide-apatite (IOA) mineral deposits with variable concentrations of rare earth elements (REE). The IOA mineral deposits are typically hosted in the Lyon Mountain Granite Gneiss and are spatially correlated with extensive Na metasomatism (albitization) of the surrounding country rocks, although some mineral deposits also occur in metagabbro, paragneiss, and anorthosite hosts. The location of albitization zones is key to finding new IOA mineral deposits and better understanding the mineralization processes associated with their genesis. However, the Na alteration zones are generally not visibly identifiable in outcrop or hand specimens because the color and textural changes are subtle and are thus difficult to map. Here, we discuss the results from testing two spectroscopic techniques (handheld, field gamma-ray spectroscopy, and portable X-ray fluorescence (pXRF)) to characterize albitization zones surrounding IOA mineral deposits. The gamma-ray and pXRF spectrometers successfully distinguished the relative intensity of alteration in the Lyon Mountain Granite Gneiss based on the K abundance. The measured K content decreases towards the IOA mineral deposits, and the magnitude and width of the gradient are similar along the strike of each mineral deposit. Elevated Th and U values are present in host rocks adjacent to REE-bearing IOA mineral deposits. The pXRF and gamma-ray spectrometer K values are remarkably consistent with laboratory-based, whole-rock XRF compositional data and, therefore, useful for semi-quantitative analysis. Notably, albitization aureoles are consistent around REE-rich and REE-poor mineral deposits, suggesting that saline fluids are essential for the petrogenesis of IOA mineral deposits but may not be critical to REE mineralization. Ultimately, this study demonstrates the utility of handheld gamma-ray and pXRF spectrometry for identifying otherwise cryptic albitization gradients associated with IOA mineral deposits in granitic gneiss.

New York↗
USGS2026

Seismic characteristics of the April 2024 eruption of Ruang Volcano, North Sulawesi, Indonesia

The two most recent eruptions of Ruang volcano, in 2002 and 2024, have been large (VEI 4) with very short precursory periods, 3 and 6 days, respectively. Background seismicity at Ruang volcano is generally low with 0–2 volcano-tectonic (VT) earthquakes per day. The 2024 eruptions were preceded by a notable increase in VT earthquakes from 11 to 15 April with a rapid escalation from 16 to 17 April in the form of increased VT swarms, and the appearance of low frequency earthquakes and short bursts of VT drumbeats shortly before the eruption. Similar VT seismic unrest was recorded in March 2015, May 2016, and April 2022, although none of these episodes culminated in an eruption. A comparison of seismic energy release between April 2022 and April 2024 shows distinct differences. In 2024, cumulative seismic energy reached its peak within 5 days, just before the onset of eruption on 17 April. In contrast, during the 2022-episode, energy release followed a more gradual increase over 8 days peaking on 16 April, then declining gradually without leading to eruption. Notably, low frequency (LF) and drumbeat earthquakes were absent in non-eruptive unrest episodes. The transition to proximal LFs in 2024 likely signals pressure fluctuations, intensified magma degassing, and conduit formation, acting as an important precursor to eruption. Additionally, the occurrence of short bursts of drumbeat seismicity likely reflects the onset of the shallow magma ascent and was an important short-term precursor to the eruption. Finally, we examine the potential influence of regional tectonic earthquakes on the escalation of precursory unrest in 2024.

North Sulawesi, Ruang volcano↗
USGS2025

Spatiotemporal variations in strain release and seismic rupture in multifault systems: An example from Panamint Valley, southeastern California

Geometrically complex, multifault ruptures have been observed in recent, damaging earthquakes in southeastern California, sparking renewed efforts to identify physical conditions that promote or inhibit fault discontinuity-spanning coseismic ruptures. The likelihood of ruptures propagating across fault discontinuities is thought to be partly controlled by fault geometries, rupture direction, and the history of strain release. However, these parameters vary in space and time over multiple earthquake cycles, making it difficult to forecast the likelihood that an earthquake on one fault will trigger rupture on a nearby fault. Here we use tectono-geomorphic mapping of a geometrically complex fault zone in Panamint Valley, southeastern California, to assess spatiotemporal variations of paleo-rupture patterns and geometries of fault discontinuities over multiple earthquake cycles. First, we identify ten generations of late Pleistocene to Holocene alluvium using geomorphic parameters and luminescence dating to constrain ages of alluvium and bracket late Holocene earthquake timing. Then, we quantify slip kinematics using high-resolution structure from motion digital surface models. We find the Panamint Valley transtensional relay (PVTR) hosted four late Holocene earthquakes, bracketed to ~5.8–3.4 ka, ~3.8–2.2 ka, ~2.4–0.6 ka, and ~0.64–0.16 ka, with ~0.6–1.1 m of slip per event, correlative to Mw ≈ 6.7–6.9 earthquakes. Additionally, we find similarities in earthquake timing on the Ash Hill, PVTR, and Panamint Valley faults and similarities in the slip magnitude and slip kinematics between the Ash Hill and PVTR faults, implying that the PVTR may co-rupture with nearby faults. Paleo-rupture patterns indicate that seismogenic strain transfer may occur through the PVTR, along different combinations of fault segments and jump distances, over multiple earthquake cycles. These data highlight the utility of tectono-geomorphic mapping in evaluating paleo-rupture patterns and suggest that the PVTR may act to propagate and/or arrest rupture between the Ash Hill and Panamint Valley faults.

California↗
USGS2026

Keeping pace: Migrating sea lampreys adjust swim speed in response to shifting water velocity to maintain a constant ground speed

Upstream migrating fish must balance energetic costs with environmental and ecological constraints. Theoretical models predict that fish can conserve energy by adjusting swim speed in response to changing water velocity, but detailed field tests of these predictions remain rare. We used fine-scale acoustic telemetry and hydrodynamic modeling to track adult sea lamprey (Petromyzon marinus) migrating through a river and evaluated how movement speeds varied with environmental conditions and individual traits. Swim speed increased with faster water velocities, while ground speed remained constant, supporting the hypothesis that lampreys regulate swim effort to maintain a fixed migration pace. The average ground speed aligned with a predicted optimum of ∼1 body length per second. Both swim and ground speeds declined slightly in deeper water, suggesting a trade-off between movement efficiency and predator avoidance. These findings provide field-based support for a theoretical model of energy optimization and underscore how migratory fish adaptively adjust behavior to local hydrodynamic conditions. Our results highlight the value of using high-resolution tracking and environmental modeling to reveal behavioral tactics that underlie efficient migration strategies.

Michigan↗
USGS2026

Uranium—Deposits, production and resources, market dynamics, and supply chain risks

Introduction Interest in nuclear power for the generation of electricity has risen with the increase in the need for more diverse baseload power, enhanced energy security, and the development of new technologies, such as small modular reactors (SMRs), which could provide power for remote areas, industrial applications, and artificial intelligence (AI) data centers. In 2024, the U.S. Department of Energy received $2.7 billion in congressional funding to bolster the domestic uranium production and nuclear fuel supply chain and address reliance on imports from foreign suppliers. In 2025, the U.S. Government issued several Executive and Secretary’s orders aimed at revitalizing the U.S. nuclear sector. If SMRs are to be as widely deployed in the United States and worldwide as envisioned, demand for uranium (nuclear reactor fuel) will likely increase. After the Fukushima nuclear accident in 2011, the market spot price of uranium began a decline, followed by a decrease in U.S. and global uranium exploration and mine development expenditures that led to a uranium supply deficit until 2020, when prices started to recover, prompting a resurgence in uranium exploration and development. In January of 2024, the uranium spot price rose to a 17-year high $106 (U.S. dollars) per pound of U3O8 (triuranium oxide, commonly known as “yellowcake”), which is expected to increase uranium exploration, mine development, and uranium production domestically and worldwide.

Fact Sheet↗
USGS2026

Lithium brine potential of North Dakota: Results from the 2025 sampling program

Lithium (Li), classified as a critical mineral and key in energy storage applications because of its high energy density, faces unprecedented demand. This has driven interest in unconventional sources of Li, especially brines from sedimentary basins. Accordingly, the spatial distribution of basinal brinehosted Li resources across North America is becoming better defined, including the Williston Basin underlying Saskatchewan, Canada. This has led to growing investment and exploration by industry throughout the 2020s; however, despite this interest, the Li potential of basinal brines of the Williston Basin in North Dakota remain underexplored. This work presents the results from the 2025 joint brine sampling campaign between the North Dakota Geological Survey, the United States Geological Survey (USGS), and The University of Texas at Austin. Twenty-seven fluid samples were collected from producing oil and water source wells from eight stratigraphic intervals across western North Dakota and analyzed for major cation and anion concentrations. Similar to southeastern Saskatchewan, the highest Li concentrations were identified in the Devonian Duperow Formation, with concentrations up to 179 mg/L being observed in a well commingled between the Duperow and Red River Formations. Some samples from the overlying Birdbear Formation exceeded 75 mg/L, whereas Li concentrations were lower in the Madison Group (33-44 mg/L) and the Three Forks (50 mg/L), Dawson Bay (43 mg/L), Winnipegosis (23 mg/L), and Red River (40.0 mg/L) Formations. This work indicates Li resource potential exists across the Williston Basin and advances our understanding of the Li distribution in basinal brines which could provide a new domestic source of this critical mineral.

North Dakota↗