USGS Science⌕ Search

SEARCH · USGS Science

Results for “Engineering Structures”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45Linked to original sources
USGS2009

EAARL Coastal Topography-Assateague Island National Seashore, 2008: First Surface

These remotely sensed, geographically referenced elevation measurements of lidar-derived first-surface (FS) topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), Northeast Coastal and Barrier Network, Kingston, RI; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the Assateague Island National Seashore in Maryland and Virginia, acquired March 24-25, 2008. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for pre-survey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

Data Series↗
USGS2009

EAARL Coastal Topography-Assateague Island National Seashore, 2008: Bare Earth

These remotely sensed, geographically referenced elevation measurements of lidar-derived bare-earth (BE) topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), Northeast Coastal and Barrier Network, Kingston, RI; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the Assateague Island National Seashore in Maryland and Virginia, acquired March 24-25, 2008. The datasets are made available for use as a management tool to research scientists and natural-resource managers. An innovative airborne lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL) was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of lidar data in an interactive or batch mode. Modules for pre-survey flight-line definition, flight-path plotting, lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is used routinely to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of last return elevations.

Data Series↗
USGS2008

Documentation for the 2008 update of the United States National Seismic Hazard Maps

The 2008 U.S. Geological Survey (USGS) National Seismic Hazard Maps display earthquake ground motions for various probability levels across the United States and are applied in seismic provisions of building codes, insurance rate structures, risk assessments, and other public policy. This update of the maps incorporates new findings on earthquake ground shaking, faults, seismicity, and geodesy. The resulting maps are derived from seismic hazard curves calculated on a grid of sites across the United States that describe the frequency of exceeding a set of ground motions. The USGS National Seismic Hazard Mapping Project developed these maps by incorporating information on potential earthquakes and associated ground shaking obtained from interaction in science and engineering workshops involving hundreds of participants, review by several science organizations and State surveys, and advice from two expert panels. The new probabilistic hazard maps represent an update of the 2002 seismic hazard maps developed by Frankel and others (2002), which used the methodology developed for the 1996 version of the maps (Frankel and others, 1996). Algermissen and Perkins (1976) published the first probabilistic seismic hazard map of the United States which was updated in Algermissen and others (1990). The National Seismic Hazard Maps represent our assessment of the “best available science” in earthquake hazards estimation for the United States (maps of Alaska and Hawaii as well as further information on hazard across the United States are available on our Web site at http://earthquake.usgs.gov/research/hazmaps/ ).

Open-File Report↗
USGS2003

Stage-discharge relations for selected culverts and bridges in the Big Lost River flood plain at the Idaho National Engineering and Environmental Laboratory, Idaho

Information is needed by the U.S. Department of Energy at the Idaho National Engineering and Environmental Laboratory to determine the extent and severity of potential flooding at facilities along the Big Lost River. Two computer programs—the Culvert Analysis Program (CAP) and the HECRAS model—were used to define stage-discharge relations for 31 culverts and 2 bridge sites in a 10- mile reach of the river. These relations can be used to improve surface-water-flow models to evaluate potential flooding. Relations between headwater, tailwater, and discharge through each structure were unique. Discharge through the culverts as computed by the CAP ranged from about 0 cubic feet per second to as much discharge as could be conveyed, and tailwater elevations ranged from about 0 to 30 feet above the outlet elevation. Discharge through the bridges, as computed by the HEC-RAS model, ranged from nearly 0 to 7,000 cubic feet per second, and tailwater elevations ranged from nearly 0 to 30 feet above the streambed on the downstream cross section of each bridge. Stage-discharge relations provided in lookup tables in this report can be incorporated into numerical surface-water-flow models to simulate the effects of hydraulic structures on flood flows. One limitation of the CAP and HEC-RAS models is that changes in flow conditions, such as obstruction by sediment and debris, are not simulated. If flow through a hydraulic structure is obstructed by sediment or debris, then model-simulated discharges through the structure might be greater than would be experienced under actual conditions.

Idaho↗
USGS2020

An international code comparison study on coupled thermal, hydrologic and geomechanical processes of natural gas hydrate-bearing sediments

Geologic reservoirs containing gas hydrate occur beneath permafrost environments and within marine continental slope sediments, representing a potentially vast natural gas source. Numerical simulators provide scientists and engineers with tools for understanding how production efficiency depends on the numerous, interdependent (coupled) processes associated with potential production strategies for these gas hydrate reservoirs. Confidence in the modeling and forecasting abilities of these gas hydrate reservoir simulators (GHRSs) grows with successful comparisons against laboratory and field test results, but such results are rare, particularly in natural settings. The hydrate community recognized another approach to building confidence in the GHRS: comparing simulation results between independently developed and executed computer codes on structured problems specifically tailored to the interdependent processes relevant for gas hydrate-bearing systems. The United States Department of Energy, National Energy Technology Laboratory (DOE/NETL), sponsored the first international gas hydrate code comparison study, IGHCCS1, in the early 2000s. IGHCCS1 focused on coupled thermal and hydrologic processes associated with producing gas hydrates from geologic reservoirs via depressurization and thermal stimulation. Subsequently, GHRSs have advanced to model more complex production technologies and incorporate geomechanical processes into the existing framework of coupled thermal and hydrologic modeling. This paper contributes to the validation of these recent GHRS developments by providing results from a second GHRS code comparison study, IGHCCS2, also sponsored by DOE/NETL. IGHCCS2 includes participants from an international collection of universities, research institutes, industry, national laboratories, and national geologic surveys. Study participants developed a series of five benchmark problems principally involving gas hydrate processes with geomechanical components. The five problems range from simple geometries with analytical solutions to a representation of the world’s first offshore production test of methane hydrates, which was conducted with the depressurization method off the coast of Japan. To identify strengths and limitations in the various GHRSs, study participants submitted solutions for the benchmark problems and discussed differing results via teleconferences. The GHRSs evolved over the course of IGHCCS2 as researchers modified their simulators to reflect new insights, lessons learned, and suggested performance enhancements. The five benchmark problems, final sample solutions, and lessons learned that are presented here document the study outcomes and serve as a reference guide for developing and testing gas hydrate reservoir simulators.

Journal of Marine and Petroleum Geology↗
USGS2005

Implications of global climatic change and energy cost and availability for the restoration of the Mississippi delta

Over the past several thousand years, inputs from the Mississippi River formed the Mississippi delta, an area of about 25,000 km 2 . Over the past century, however, there has been a high loss of coastal wetlands of about 4800 km 2 . The main causes of this loss are the near complete isolation of the river from the delta, mostly due to the construction of flood control levees, and pervasive hydrological disruption of the deltaic plain. There is presently a large-scale State-Federal program to restore the delta that includes construction of water control structures in the flood control levees to divert river water into deteriorating wetlands and pumping of dredged sediment, often for long distances, for marsh creation. Global climate change and decreasing availability and increasing cost of energy are likely to have important implications for delta restoration. Coastal restoration efforts will have to be more intensive to offset the impacts of climate change including accelerated sea level rise and changes in precipitation patterns. Future coastal restoration efforts should also focus on less energy-intensive, ecologically engineered management techniques that use the energies of nature as much as possible. Diversions may be as important for controlling salinity as for providing sediments and nutrients for restoring coastal wetlands. Energy-intensive pumping-dredged sediments for coastal restoration will likely become much more expensive in the future.

Louisiana↗
USGS2016

Ecological resilience

Resilience is the capacity of complex systems of people and nature to withstand disturbance without shifting into an alternate regime, or a different type of system organized around different processes and structures (Holling, 1973). Resilience theory was developed to explain the non-linear dynamics of complex adaptive systems, like social-ecological systems (SES) (Walker & Salt, 2006). It is often apparent when the resilience of a SES has been exceeded as the system discernibly changes, such as when a thriving city shifts into a poverty trap, but it is difficult to predict when that shift might occur because of the non-linear dynamics of complex systems. Ecological resilience should not be confused with engineering resilience (Angeler & Allen, 2016), which emphasizes the ability of a SES to perform a specific task consistently and predictably, and to re-establish performance quickly should a disturbance occur. Engineering resilience assumes that complex systems are characterized by a single equilibrium state, and this assumption is not appropriate for complex adaptive systems such as SES. In the risk governance context this means that compounded perturbations derived from hazards or global change can have unexpected and highly uncertain effects on natural resources, humans and societies. These effects can manifest in regime shifts, potentially spurring environmental degradation that might lock SES in an undesirable system state that can be difficult to reverse, and as a consequence economic crises, conflict, human health problems.

Book chapter↗
USGS2002

Potentiometric surfaces, altitudes of the tops, and hydrogeology of the Minnelusa and Madison aquifers, Black Hills area, Wyoming

The topographically defined Black Hills and adjacent areas (Black Hills area) of Wyoming (fig. 1) are underlain by two regionally important aquifers - the Minnelusa and the Madison. The Minnelusa aquifer is used extensively in the Black Hills area as a source of domestic and livestock water. The Madison aquifer is an important source of municipal, industrial, agricultural, and domestic water in both the Black Hills area and other parts of Wyoming. Increased demand for water from the Minnelusa and Madison aquifers in the Black Hills area of Wyoming and South Dakota have created a need for better understanding of the hydrology of these two important aquifers. This report presents information on the potentiometric surfaces and altitudes of the tops of the Minnelusa and Madison aquifers in the Black Hills area of northeastern Wyoming using new data collected since completion of earlier studies. In addition, ground-water levels in selected wells are examined, and the relative age of a limited number of ground-water samples are discussed. The information will be of use to government officials, land planners and other individuals who must manage the limited water resources of this growing and developing area. The scope of the project was limited to wells and springs in the Black Hills area of Wyoming. Water levels were measured during 1998 and 1999 in wells completed in the Minnelusa and Madison aquifers to construct potentiometric-surface maps. The potentiometric surfaces and altitudes of the tops of the Minnelusa and Madison aquifers were contoured at the same scale (1:100,000) as studies of the aquifers recently conducted by the U.S. Geological Survey (USGS) in the Black Hills area within South Dakota (Carter and Redden, 1999a, 1999b; Strobel and others, 2000a, 2000b). The contours in these studies of the Minnelusa and Madison aquifers in South Dakota were "edge matched" as closely as possible along the Wyoming-South Dakota State line using the same contour interval. Use of the same contour interval and edge matching will allow for the use of the maps across State boundaries and improve understanding of the aquifers in a larger area within the Black Hills uplift. In places, some contours could not be matched across the Wyoming-South Dakota State line because this investigation was completed after the South Dakota investigations, and additional control points used in this investigation were located in Wyoming near the State line. The reader should note that Minnelusa and Madison outcrop areas and some structural features may not match in some areas along the Wyoming-South Dakota State line when maps in this study area are aligned or "edge matched" with maps produced for the South Dakota studies because different sources of geological mapping were used for the studies. Ground-water samples were collected from a subset of measured wells and analyzed for tritium to qualitatively estimate the time of ground-water recharge. This project was conducted by the USGS in cooperation with the Wyoming State Engineer's Office (WSEO). The study area was almost entirely within Crook and Weston Counties in Wyoming and was bordered on the east by the Wyoming-South Dakota State line.

Hydrologic Atlas↗
USGS1994

Liquefaction during the 1977 San Juan Province, Argentina earthquake (Ms = 7.4)

Liquefaction effects generated by the 1977 San Juan Province, Argentina, earthquake (Ms = 7.4) are described. The larger and more abundant effects were concentrated in the 60-km long band of the lowlands in the Valle del Bermejo and in an equally long band along the Rio San Juan in the Valle de Tulum. Fissures in the Valle del Bermejo were up to several hundred meters long and up to several meters wide. Sand deposits, from boils that erupted through the fissures, covered areas up to tens of square meters. Fissures generally parallelled nearby stream channels. Because the Valle del Bermejo is undeveloped, these large features caused no damage. Liquefaction in the Valle del Tulum caused important or unusual damage at several localities, including the following five sites: (1) At the Barrio Justo P. Castro, a subdivision of Caucete, liquefaction of subsurface sediments decoupled overlying, unliquefied stiff sediments, producing a form of ground failure called "ground oscillation". The associated differential ground movements pulled apart houses and pavements in extension, while shearing curbs and buckling canal linings in compression at the same locality. (2) At the Escuela Normal, in Caucete, the roof of a 30-m long single-story classroom building shifted westward relative to the foundation. That displacement fractured and tilted columns supporting the roof. The foundation was fractured at several places, leaving open cracks, as wide as 15 mm. The cumulative width of the open cracks was 48 mm, an amount roughly equivalent to the 63 mm of offset between the roof and foundation at the east end of the building. The ground and foundation beneath the building extended (or spread) laterally opening cracks and lengthening the foundation while the roof remained in place. (3) The most spectacular damage to structures at the community of San Martin was the tilting of a 6-m high water tower and the toppling of a nearby pump house into a 1-m deep crater. Similarly, a small crater developed beneath a hand-pump in an open area and a large, 6-m diameter crater formed nearby. The following sequence of events created the craters and toppled the pump structures: During the earthquake, ground shaking generated excess pore pressures which were dissipated by upward flow of groundwater. Free drainage was restricted by an impermeable plastic-silt layer. Water apparently accumulated below the plastic-silt layer and then burst to the surface through several holes and cracks, including holes around well casings. (4) At the San Isidro winery, nine storage tanks tilted 2 to 5??. Five reinforced-concrete tanks were dismantled but four steel tanks were repaired by placing new footings and jacking the structures into an upright position. (5) At Escuela J.J. Pasos, differential settlement beneath building fractured several columns and walls. The largest settlements were about 60 mm and the maximum settlement of footings supporting columns was about 40 mm. In spite of the damage, the buildings were in no danger of collapse.

San Juan Province↗
USGS1965

Effects of the earthquake of March 27, 1964, at Anchorage, Alaska

Anchorage, Alaska’s largest city, is about 80 miles west-northwest of the epicenter of the March 27 earthquake. Because of its size, Anchorage bore the brunt of property damage from the quake; it sustained greater losses than all the rest of Alaska combined. Damage was caused by direct seismic vibration, by ground cracks, and by landslides. Direct seismic vibration affected chiefly multistory buildings and buildings having large floor areas, probably because of the long period and large amplitude of the seismic waves reaching Anchorage. Most small buildings were spared. Ground cracks caused capricious damage throughout the Anchorage Lowland. Cracking was most prevalent near the heads or within landslides but was also widespread elsewhere. Landslides themselves caused the most devastating damage. Triggering of landslides by the earthquake was related to the physical-engineering properties of the Bootlegger Cove Clay, a glacial estuarine-marine deposit that underlies much of the Anchorage area. The Bootlegger Cove Clay contains zones of low shear strength, high water content, and high sensitivity that failed under the vibratory stress of the earthquake. Shear strength in sensitive zones ranged from less than 0.2 tsf to about 0.5 tsf; sensitivity ranged from about 10 to more than 40. Sensitive zones generally are centered about 10 to 20 feet above sea level, between zones of stiff insensitive clay. Many physical tests by the U.S. Army Corps of Engineers were directed toward analyzing the causes of failure in the Bootlegger Cove Clay and finding possible remedies. Strengths and sensitivities were measured directly in the field by means of vane shear apparatus. A4tterberg limits, natural water contents, triaxial shear, sensitivity, dynamic modulus, consolidation strength, and other properties were measured in the laboratory. Pulsating-load tests simulated earthquake loading. Most of the destructive landslides in the Anchorage area moved primarily by translation rather than by rotation. Thus, all the highly damaging slides were of a single structural dynamic family despite wide variations in size, appearance, and complexity. They slid on nearly horizontal slip surfaces after loss of strength in the Bootlegger Core Clay. Same failures are attributed to spontaneous liquefaction of sand layers. All translatory slides surmounted flat-topped bluffs bounded marginally by steep slopes facing lower ground. Destructive translatory slides occurred in the downtown area (Fourth Avenue slide and L Street slide), at Government Hill, and at Turnagain Heights. Less destructive slides occurred in many other places-mostly uninhabited or undeveloped areas. In most translatory slides, damage was greatest in graben areas at the head and in pressure-ridge areas at the toe. Many buildings inside the perimeters of slide blocks were little damaged despite horizontal translations of several feet. The large Turnagain Heights slide, however, was characterized by a complete disintegration and drastic lowering of the prequake land surface. Extensive damage back from the slide, moreover, was caused by countless tension cracks. An approximation of the depth of failure in the Bootlegger Cove Clay in the various slides may be obtained by using a geometric relationship herein called the "graben rule." Because the cross-sectional area of the graben at the head of the slide approximated the cross-sectional area of the space voided behind the slide block as the block moved outward, the depth of failure was equal to the area of the graben divided by the lateral displacement. This approximation supplements and accords with test data obtained from borings. The graben rule should apply to any translatory slide in which flowage of material from the zone of failure has not been excessive. Geologic evidence indicates that landslides similar to those triggered by the March 27 earthquake have occurred in the Anchorage area at various times in the past.

Alaska↗
USGS1994

Neural networks for river flow prediction

The surface‐water hydrographs of rivers exhibit large variations due to many natural phenomena. One of the most commonly used approaches for interpolating and extending streamflow records is to fit observed data with an analytic power model. However, such analytic models may not adequately represent the flow process, because they are based on many simplifying assumptions about the natural phenomena that influence the river flow. This paper demonstrates how a neural network can be used as an adaptive model synthesizer as well as a predictor. Issues such as selecting an appropriate neural network architecture and a correct training algorithm as well as presenting data to neural networks are addressed using a constructive algorithm called the cascade‐correlation algorithm. The neural‐network approach is applied to the flow prediction of the Huron River at the Dexter sampling station, near Ann Arbor, Mich. Empirical comparisons are performed between the predictive capability of the neural network models and the most commonly used analytic nonlinear power model in terms of accuracy and convenience of use. Our preliminary results are quite encouraging. An analysis performed on the structure of the networks developed by the cascade‐correlation algorithm shows that the neural networks are capable of adapting their complexity to match changes in the flow history and that the models developed by the neural‐network approach are more complex than the power model.

Journal of Computing in Civil Engineering↗
USGS1996

Ground-Water Discharge to Biscayne Bay

Introduction The South Florida Ecosystem Restoration Program is an intergovernmental effort, involving a number of agencies, to reestablish and maintain the ecosystem of south Florida. One element of the restoration effort is the development of a firm scientific basis for resource decision making. The U.S. Geological Survey (USGS), one of the agencies, provides scientific information as part of the South Florida Ecosystem Restoration Program. The USGS began their own program, called the South Florida Ecosystem Program, in fiscal year 1995 for the purpose of gathering hydrologic, cartographic, and geologic data that relate to the mainland of south Florida, Florida Bay, and the Florida Keys and Reef ecosystems. Over the years, the construction of canals and levees has altered the natural hydrologic conditions of the Everglades. The canals and levees were constructed to convey water, prevent flooding, and store water in conservation areas for future use. The U.S. Army Corps of Engineers (COE) in Jacksonville, Fla., is planning to construct gated spillways and culverts to allow for the restoration of natural sheetflow conditions to Everglades National Park (ENP). These proposed changes may further affect the hydrologic conditions of ENP and other parts of the ecosystem, thus leading to the following questions: Is ground water flowing to Biscayne Bay a significant component of the water budget in south Florida? Would the quantity of ground water flowing to Biscayne Bay be greatly affected by changes in the operation of gates and control structures in canals? How much change in ground-water discharges to Biscayne Bay has occurred due to modifications to the hydrologic system? Federal, State, and local agencies need to know the effect that changes in the operation of gates and control structures in canals will have on the water-budget components of the natural water systems in south Florida, including ground-water flow to Biscayne Bay.

Florida↗
USGS1989

A close-range photogrammetric technique for mapping neotectonic features in trenches

Close-range photogrammetric techniques and newly available computerized plotting equipment were used to map exploratory trench walls that expose Quaternary faults in the vicinity of Yucca Mountain, Nevada. Small-scale structural, lithologic, and stratigraphic features can be rapidly mapped by the photogrammetric method. This method is more accurate and significantly more rapid than conventional trench-mapping methods, and the analytical plotter is capable of producing cartographic definition of high resolution when detailed trench maps are necessary.

Bulletin of the Association of Engineering Geologi↗
USGS2013

National assessment of geologic carbon dioxide storage resources: Results

In 2012, the U.S. Geological Survey (USGS) completed an assessment of the technically accessible storage resources ( TA SR ) for carbon dioxide (CO 2 ) in geologic formations underlying the onshore and State waters area of the United States. The formations assessed are at least 3,000 feet (914 meters) below the ground surface. The TA SR is an estimate of the CO 2 storage resource that may be available for CO 2 injection and storage that is based on present-day geologic and hydrologic knowledge of the subsurface and current engineering practices. Individual storage assessment units (SAUs) for 36 basins were defined on the basis of geologic and hydrologic characteristics outlined in the assessment methodology of Brennan and others (2010, USGS Open-File Report 2010–1127) and the subsequent methodology modification and implementation documentation of Blondes, Brennan, and others (2013, USGS Open-File Report 2013–1055). The mean national TA SR is approximately 3,000 metric gigatons (Gt). The estimate of the TA SR includes buoyant trapping storage resources ( B SR ), where CO 2 can be trapped in structural or stratigraphic closures, and residual trapping storage resources, where CO 2 can be held in place by capillary pore pressures in areas outside of buoyant traps. The mean total national B SR is 44 Gt. The residual storage resource consists of three injectivity classes based on reservoir permeability: residual trapping class 1 storage resource ( R1 SR ) represents storage in rocks with permeability greater than 1 darcy (D); residual trapping class 2 storage resource ( R2 SR ) represents storage in rocks with moderate permeability, defined as permeability between 1 millidarcy (mD) and 1 D; and residual trapping class 3 storage resource ( R3 SR ) represents storage in rocks with low permeability, defined as permeability less than 1 mD. The mean national storage resources for rocks in residual trapping classes 1, 2, and 3 are 140 Gt, 2,700 Gt, and 130 Gt, respectively. The known recovery replacement storage resource ( KRR SR ) is a conservative estimate that represents only the amount of CO 2 at subsurface conditions that could replace the volume of known hydrocarbon production. The mean national KRR SR , determined from production volumes rather than the geologic model of buoyant and residual traps that make up TA SR , is 13 Gt. The estimated storage resources are dominated by residual trapping class 2, which accounts for 89 percent of the total resources. The Coastal Plains Region of the United States contains the largest storage resource of any region. Within the Coastal Plains Region, the resources from the U.S. Gulf Coast area represent 59 percent of the national CO 2 storage capacity.

Circular↗
USGS2004

Summary and Comparison of Multiphase Streambed Scour Analysis at Selected Bridge Sites in Alaska

The U.S. Geological Survey and the Alaska Department of Transportation and Public Facilities undertook a cooperative multiphase study of streambed scour at selected bridges in Alaska beginning in 1994. Of the 325 bridges analyzed for susceptibility to scour in the preliminary phase, 54 bridges were selected for a more intensive analysis that included site investigations. Cross-section geometry and hydraulic properties for each site in this study were determined from field surveys and bridge plans. Water-surface profiles were calculated for the 100- and 500-year floods using the Hydrologic Engineering Center?s River Analysis System and scour depths were calculated using methods recommended by the Federal Highway Administration. Computed contraction-scour depths for the 100- and 500-year recurrence-interval discharges exceeded 5 feet at six bridges, and pier-scour depths exceeded 10 feet at 24 bridges. Complex pier-scour computations were made at 10 locations where the computed contraction-scour depths would expose pier footings. Pressure scour was evaluated at three bridges where the modeled flood water-surface elevations intersected the bridge structure. Site investigation at the 54 scour-critical bridges was used to evaluate the effectiveness of the preliminary scour analysis. Values for channel-flow angle of attack and approach-channel width were estimated from bridge survey plans for the preliminary study and were measured during a site investigation for this study. These two variables account for changes in scour depths between the preliminary analysis and subsequent reanalysis for most sites. Site investigation is needed for best estimates of scour at bridges with survey plans that indicate a channel-flow angle of attack and for locations where survey plans did not include sufficient channel geometry upstream of the bridge.

Scientific Investigations Report↗
USGS2017

Implementing Nepal's national building code—A case study in patience and persistence

The April 2015 Gorkha Nepal earthquake revealed the relative effectiveness of the Nepal Standard, or national building code (NBC), and irregular compliance with it in different parts of Nepal. Much of the damage to more than half a million Nepal's residential structures may be attributed to the prevalence of owner-built or owner-supervised construction and the lack of owner and builder responsiveness to seismic risk and training in the appropriate means of complying with the NBC. To explain these circumstances, we review the protracted implementation of the NBC and the role played by one organization, the National Society for Earthquake Technology-Nepal (NSET), in the NBC's implementation. We also share observations on building code compliance made by individuals in Nepal participating in workshops led by the Earthquake Engineering Research Institute's 2014 class of Housner Fellows.

Earthquake Spectra↗
USGS2014

Estimating structural collapse fragility of generic building typologies using expert judgment

The structured expert elicitation process proposed by Cooke (1991), hereafter referred to as Cooke’s approach, is applied for the first time in the realm of structural collapse-fragility assessment for selected generic construction types. Cooke’s approach works on the principle of objective calibration scoring of judgments coupled with hypothesis testing used in classical statistics. The performance-based scoring system reflects the combined measure of an expert’s informativeness about variables in the problem area under consideration, and their ability to enumerate, in a statistically accurate way through expressing their true beliefs, the quantitative uncertainties associated with their assessments. We summarize the findings of an expert elicitation workshop in which a dozen earthquake-engineering professionals from around the world were engaged to estimate seismic collapse fragility for generic construction types. Development of seismic collapse fragility functions was accomplished by combining their judgments using weights derived from Cooke’s method. Although substantial effort was needed to elicit the inputs of these experts successfully, we anticipate that the elicitation strategy described here will gain momentum in a wide variety of earthquake seismology and engineering hazard and risk analyses where physical model and data limitations are inherent and objective professional judgment can fill gaps.

Conference Paper↗
USGS2006

Estimated flood-inundation mapping for the Lower Blue River in Kansas City, Missouri, 2003-2005

The U.S. Geological Survey, in cooperation with the city of Kansas City, Missouri, began a study in 2003 of the lower Blue River in Kansas City, Missouri, from Gregory Boulevard to the mouth at the Missouri River to determine the estimated extent of flood inundation in the Blue River valley from flooding on the lower Blue River and from Missouri River backwater. Much of the lower Blue River flood plain is covered by industrial development. Rapid development in the upper end of the watershed has increased the volume of runoff, and thus the discharge of flood events for the Blue River. Modifications to the channel of the Blue River began in late 1983 in response to the need for flood control. By 2004, the channel had been widened and straightened from the mouth to immediately downstream from Blue Parkway to convey a 30-year flood. A two-dimensional depth-averaged flow model was used to simulate flooding within a 2-mile study reach of the Blue River between 63rd Street and Blue Parkway. Hydraulic simulation of the study reach provided information for the design and performance of proposed hydraulic structures and channel improvements and for the production of estimated flood-inundation maps and maps representing an areal distribution of water velocity, both magnitude and direction. Flood profiles of the Blue River were developed between Gregory Boulevard and 63rd Street from stage elevations calculated from high water marks from the flood of May 19, 2004; between 63rd Street and Blue Parkway from two-dimensional hydraulic modeling conducted for this study; and between Blue Parkway and the mouth from an existing one-dimensional hydraulic model by the U.S. Army Corps of Engineers. Twelve inundation maps were produced at 2-foot intervals for Blue Parkway stage elevations from 750 to 772 feet. Each map is associated with National Weather Service flood-peak forecast locations at 63rd Street, Blue Parkway, Stadium Drive, U.S. Highway 40, 12th Street, and the Missouri River at the Hannibal railroad bridge in Kansas City. The National Weather Service issues peak-stage forecasts for these locations during times of flooding. Missouri River backwater inundation profiles were developed using interpolated Missouri River stage elevations at the mouth of the Blue River. Twelve backwater-inundation maps were produced at 2-foot intervals for the mouth of the Blue River from 730.9 to 752.9. To provide public access to the information presented in this report, a World Wide Web site (http://mo.water.usgs.gov/indep/kelly/blueriver/index.htm) was created that displays the results of two-dimensional modeling between 63rd Street and Blue Parkway, estimated flood-inundation maps, estimated backwater-inundation maps, and the latest gage heights and National Weather Service stage forecast for each forecast location within the study area. In addition, the full text of this report, all tables, and all plates are available for download at http://pubs.water.usgs.gov/sir2006-5089.

Missouri↗