USGS Science⌕ Search

SEARCH · USGS Science

Results for “Geological Society of America Bulletin”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,666 records · Page 44Linked to original sources
USGS1999

Simulation of the effects of development of the ground-water flow system of Long Island, New York

Extensive development on Long Island since the late 19th century and projections of increased urbanization and ground-water use makes effective water-resource management essential for preservation of the island's hydrologic environment and maintenance of a reliable source of water supply. This report presents results of a ground-water flow simulation analysis of the effects of development on the Long Island ground-water system. It describes ground-water levels, stream-flow, and the ground-water budget for the predevelopment period (pre-1900), the 1960's drought, and a more recent (1968-83) period with significant hydrologic stress. The report also presents estimated effects of a proposed water-supply strategy for the year 2020. Long Island has three major aquifers-the upper glacial (water-table), the Magothy, and the Lloyd aquifers-that are separated to varying degrees by confining units. Before development, recharge from precipitation entered the ground-water system at a rate of more than 1.1 billion gallons per day. An equal amount discharged to streams (41 percent), the shore (52 percent), and subsea boundaries (7 percent) . Urbanization and withdrawal of more than 400 Mgal/d (million gallons per day) from wells have resulted in local effects that include declines in ground-water levels, drying up and burial of streams and wetlands, reduction of ground-water recharge by increased overland flow to the ocean, a general decrease in ground-water discharge, and salt water intrusion. In some areas, the reduction in recharge is mitigated by leakage from water-supply and wastewater disposal lines, and infiltration of storm water through recharge basins. During 1968-83, a net loss of 240 Mgal/d from the ground-water system caused a decrease in ground-water discharge to streams (135 Mgal/d), to the shore (82 Mgal/d), and to subsea boundaries (23Mgal/d).The greatest adverse effects have been in western Long Island, where the most severe development has occurred. This analysis shows stream base flow to be highly sensitive to water-table fluctuations, and long streams to be more sensitive than short ones. A water-supply scenario for the year 2020 was simulated that employs redistribution of pumping centers to mitigate extreme local effects . Although the net stress on the ground-water system was projected to increase 57 Mgal/d (24 percent) above that of 1968-83, redistribution of ground-water withdrawals across the island would allow recovery of cones of depression in western Long Island, thereby reducing the threat of salt water intrusion and increasing base flow of some streams . The increased stress would cause a net decrease in base flow island wide of 44 Mgal/d; total base flow would be 281 Mgal/d - 39 percent below predevelopment levels or 14 percent below 1968-83 levels. The most severe effects would be in Nassau and western Suffolk Counties.

New York↗
USGS2025

Hydrologic response of groundwater and streamflow to natural and anthropogenic drivers of change in headwaters of the upper Colorado River basin during recent wet (1982–1999) and drought (2000–2022) conditions

Study region: Headwaters of the upper Colorado River basin (UCOL), USA Study focus: Surface-water and groundwater numerical models incorporating water-use information were used to investigate changes in climate, water use, and simulated hydrologic responses of snow processes, evapotranspiration, groundwater, and streamflow during recent wet (1982–1999) and drought (2000–2022) periods in the headwater subregions of the upper Colorado River basin. New hydrologic insights for the region: Decreases in average streamflow between wet and drought periods ranged from 20 % in the Colorado River headwaters subregion to 23 % in the Gunnison River headwaters subregion. Like streamflow, average surface runoff was statistically less during the drought than the wet period, with decreases from 24–31 % in the headwaters. On a volume basis, runoff decreases were greater than streamflow decreases in both the Colorado River and Gunnison River headwaters. Although the amount of water-year groundwater discharge to streams remained nearly the same between the wet and drought periods, groundwater as a percentage of streamflow increased between the wet and drought periods, highlighting the importance of groundwater in sustaining streamflow during drought conditions. Multiple linear regression analyses revealed that snowmelt-only models were better than the best precipitation and temperature models at explaining streamflow variability from all headwater subregions for both the wet and drought periods.

Arizona, Colorado, New Mexico, Utah, Wyoming↗
USGS2025

A northeast-dipping zone of low frequency earthquakes at the southern edge of Cascadia subduction

Tectonic tremor monitoring occasionally detects events in an anomalous zone in southern Cascadia, 50–100 km west of the main tremor band, near the expected southern edge of the subducting Gorda slab at the Mendocino triple junction. To investigate the geometry and temporal behavior of this tremor, we examine its constituent low-frequency earthquakes (LFEs) by developing 27 stacked LFE waveform templates that we use to detect events from 2018 to 2024. We then relocate LFE sources together with regional seismicity. We find that LFE hypocenters form a northeast-dipping alignment at 22–29 km depth, extending eastward from a zone of micro-earthquakes, ∼15 km south of the southern edge of Gorda slab seismicity. These LFE families exhibit small bursts of activity every few days. Considering the strong world-wide association of tremor and LFEs with high slip-rate, plate-bounding faults, we hypothesize these LFEs may demark the southern edge of Cascadia subduction.

California↗
USGS1983

Use of digital land-cover data from the Landsat satellite in estimating streamflow characteristics in the Cumberland Plateau of Tennessee

Characteristics of Streamflow at ungaged sites in coal-mining areas of the Cumberland Plateau may be estimated with regression equations that relate streamflow characteristics to the physiographic and climatic characteristics of the corresponding drainage basins. An experiment was performed to compare the accuracy of equations using basin characteristics derived from maps and climatological records (control group equations) with the accuracy of equations using basin characteristics derived from digital processing of Landsat spectral data as well as maps and climatological records (experimental group equations). Results of this experiment show that (with the exception of low flows and four of six annual peak logarithms) drainage area can explain more than 90 percent of the variance in all streamflow characteristics in both groups of equations. Seventeen of 39 experimental group equations that have two basin characteristics each are different from the corresponding control group equations. Five of the 17 differing experimental group equations have no counterpart in the control group because of lack of significance in control group basin characteristics, seven are slightly more accurate, and five are not measurably different in accuracy. When the equations in both groups are arranged into six flow categories, there is no substantial difference in accuracy between equations using basin characteristics derived from maps and climatological records (control group) and equations using basin characteristics derived from Landsat tapes as well as maps and climatological records (experimental group) for this particular study area, the Cumberland Plateau of Tennessee.

Tennessee↗
USGS2024

Effects of drought and cloud-water interception on groundwater recharge and wildfire hazard for recent and future climate conditions, Kauaʻi, Oʻahu, Molokaʻi, Maui, and the Island of Hawaiʻi

The Water-budget Accounting for Tropical Regions Model (WATRMod) code was used for Kauaʻi, Oʻahu, Molokaʻi, Maui, and the Island of Hawaiʻi to estimate the spatial distribution of groundwater recharge, soil moisture, evapotranspiration, and climatic water deficit for a set of water-budget scenarios. The scenarios included historical and future drought conditions, and a land-cover condition where shrubland and forest within the cloud zone were converted to grassland. For the historical drought condition, island-wide mean annual recharge estimates range from a decrease of 30 percent (239 million gallons per day [Mgal/d]) for Kauaʻi to a decrease of 39 percent (2,706 Mgal/d) for the Island of Hawaiʻi, relative to the reference condition consisting of 1978–2007 rainfall and 2020 land cover. For the future drought condition, estimates of island-wide mean annual recharge range from a decrease of 40 percent (477 Mgal/d) on Maui to a decrease of 51 percent (116 Mgal/day) on Molokaʻi. Complete conversion of all shrubland and forest within the cloud zone to grassland for each drought condition produces estimated land-cover-related decreases in island-wide mean annual recharge (in addition to the drought-related decreases) of 11–12 Mgal/d on Oʻahu, 119–135 Mgal/day on Maui, and 689–849 Mgal/d on the Island of Hawaiʻi. The spatial distributions of increases in conditions indicative of moisture stress and potential wildfire hazard were quantified using the relative frequency of soil moisture less than a selected threshold value (monthly mean soil moisture less than 0.074, expressed as a fraction of available water capacity), evapotranspiration less than a selected threshold value (monthly evapotranspiration less than 0.96 inches), and climatic water deficit greater than a selected threshold value (monthly climatic water deficit greater than 0.77, expressed as fraction of potential evapotranspiration). For the historical drought condition, the greatest increases in the relative frequency for the moisture-stress indicators occur across parts of east and southwest Kauaʻi; central, east, and west Oʻahu; central Molokaʻi; central Maui and low- to mid-altitude parts of West Maui volcano; and the northwestern and southern parts of the Island of Hawaiʻi. For the future drought condition, the greatest increases in the relative frequency of the moisture-stress indicators occur across parts of west Kauaʻi; central and west Oʻahu and Molokaʻi; a band of mid-altitude area on the southern slope of West Maui volcano and across the southwestern slope of Haleakalā; and mid-altitude areas of the northwestern and southern parts of the Island of Hawaiʻi. Complete conversion of all shrubland and forest within the cloud zone to grassland for each drought condition results in land-cover-related increases in the relative frequency of moisture-stress indicators around Kaʻala in the Waiʻanae Range and the southeastern part of the Koʻolau Range on Oʻahu, the southern part of West Maui volcano and the southwestern slope of Haleakalā on Maui, and the upland regions of the western and southern parts of the Island of Hawaiʻi.

Hawaii↗
USGS2025

Rapid emplacement of the Keaiwa Lava Flow of 1823 from the Great Crack in the Southwest Rift Zone of Kilauea volcano

The Keaīwa Lava Flow of 1823 in the Southwest Rift Zone of Kīlauea volcano is unusual for its expansive pāhoehoe sheet flow morphology and lack of constructive vent topography, despite having a similar tholeiitic basalt composition to other lavas erupted from Kīlauea. This lava flow issued from a ∼10-km-long continuous fissure now known as the Great Crack, and has an unusually thin sheet flow morphology with margin thicknesses of ∼15–110 cm (average of 42 cm). Based on field observations of the lava flow at its fissure vent (e.g., drain-back features), we propose that the Great Crack formed, or at least significantly widened, just prior to and syn-eruptively with this 1823 eruption. The absence of pyroclastic cones or spatter ramparts indicates that the eruption consisted of a rapid outpouring of relatively degassed lava as the fissure unzipped. The rapidly moving lava flow overtopped pre-existing tumuli and scoria cones (e.g., Lava Plastered Cones) up to ∼10 m tall. Glass and whole-rock chemistry yield homogeneous compositions for the lavas erupted from the Great Crack, with glass compositions of 6.40 ± 0.10 wt% MgO and whole-rock compositions of 7.39 ± 0.07 wt% MgO. Lava pads erupted from a short western fissure system are richer in mafic minerals (e.g., olivine and clinopyroxene), and show slightly more MgO-rich whole-rock compositions (7.79 ± 0.05 wt%). MgO-in-glass thermometry on juvenile spatter yield eruption temperatures of 1153 ± 13°C that are typical of Kīlauea lavas. Thus, the extensive sheet-like lava flow morphology is not a direct consequence of unusual magmatic or rheological conditions (i.e., low viscosity). Instead, the flow morphology is associated with high effusion rates caused by sudden drainage of uprift magma as it erupted from the Great Crack. Lava flow modeling on a 2-m-resolution digital elevation model indicates that a minimum bulk effusion rate of ∼5800 m 3 /s (∼3500 m 3 /s dense rock equivalent) and a minimum flow velocity of ∼11 m/s are required for the lava flow to overcome the topography of the Lava Plastered Cones. This effusion rate is among the highest inferred for eruptions in Hawaiʻi and around the world. This study highlights a less frequent eruption style at Hawaiian volcanoes characterized by a sudden outpouring of lava from an unusual fissure system. Local eyewitness accounts indicate that the 1823 eruption was preceded by seismicity. Given the complex magmatic-volcanic-tectonic relations across Kīlauea, we speculate that the south flank could have slipped over one or more events that ultimately triggered unzipping of the Great Crack and passive release of briefly stored uprift magma. An eruption similar to 1823 at Kīlauea or Mauna Loa, with an eruptive timeframe that could be as short as an hour, with high effusion rates and rapid flow front velocities, would not easily allow for a timely response.

Hawaii↗
USGS1991

Reconnaissance of the occurrence of agricultural chemicals in ground water in Haywood, Lake, Obion and Shelby Counties, Tennessee

Data on the occurrence of agricultural chemicals in ground wafer in Tennessee are sparse. The surficial alluvial aquifer is an important source of domestic water supply in West Tennessee, and potentially is subject fo contamination from the application of agricultural chemicals in the area. Nineteen shallow wells completed in the alluvial aquifers in areas of high density agricultural use were sampled in the winter and again in the summer of 1988 to ascertain the occurrence of agricultural chemical in ground water. Although no triazine herbicides or organophosphorus insecticides were detected in any of the wells sampled, elevated nitrite plus nitrate (as nitrogen) concentrations were detected. Results from the winter sampling period indicate a range of nitrite plus nitrate (as nitrogen) concentrations of less than 0.1 to 7.8 milligrams per liter with a median concentration of 2.6 milligrams per liter. Results from the summer sampling period indicate a range of nitrite plus nitrate (as nitrogen) concentrations of less than 0.1 to 8.9 milligrams per liter, median, 2.5 milligrams per liter. The highest concentrations occurred in the shallowest wells, and, in one instance, in a shallow well near a heavily irrigated field.

Tennessee↗
USGS2026

Preliminary geology of the North Meadow Creek Area, Tobacco Root Mountains, southwest Montana: The North Meadow Creek Fault

This report documents a previously unmapped fault, informally referred to herein as the North Meadow Creek fault, on the east flank of the Tobacco Mountains of southwestern Montana. This fault has an apparently long and complex history, including Quaternary offset of an older alluvial terrace, offset of a debris flow of presumed Pleistocene age, offset of rhyolite lava flows of presumed Tertiary age from their presumed source several kilometers east, on the opposite side of the fault, and offset and possible rotation of blocks of Archean gneiss on northeast side of the fault. The western part of the fault is covered by glacial moraines of two apparent ages, both Pleistocene.

Montana↗
USGS2024

Deep syntectonic burial of the Anthracite belt, Eastern Pennsylvania

Fluid inclusion microthermometry and Raman spectroscopy of fluid inclusions in quartz veins from the Pennsylvanian rocks of the Anthracite belt, eastern Pennsylvania support a deep burial model of coalification in favor of focused orogenic hot fluid flow. High-temperature (250 to 255 °C) trapping of CH 4 ± CO 2 saturated aqueous fluids and CH 4 ± CO 2 inclusions indicate fluid trapping at depths of 11.5 to 13.4 km under a cover of Pennsylvanian to Permian(?) syntectonic load. In the folded rocks to the south of the Anthracite belt, CH 4 ± CO 2 fluid inclusions indicate a sediment load that was up to 16.3 km thick. Re -equilibrated aqueous fluid inclusions from veins in Silurian through Devonian rocks give the same range of trapping conditions but a wide range of fluid salinities suggesting that folding, fracturing, and meteoric recharge resulted in the intermixing of fluids from throughout the stratigraphic succession.

Pennsylvania↗
USGS2025

Assessment of density pattern retention of generalized data for 1:100,000-scale United States topographic maps

Cartographic generalization reduces the complexity of geographic data to produce legible, smaller-scale displays that retain essential information and logical geographic patterns. Generalization is a vital process in topographic map production. An important challenge in this process is managing and evaluating consistency across scale in the density and spatial distribution of map features such as buildings, roads, streams, water bodies, and elevation contours. Density patterns in these features reflect underlying physiographic conditions, which include factors such as bedrock geology, tectonics, climate, and landforms. Assessments of an acceptable level of change in feature density patterns are critical to ensuring the readability, usability, and accuracy of generalized maps and data. Preserving realistic density patterns across mapping scales also supports sustainable development goals in cartography, by helping to prioritize and communicate the relative reliability of geospatial data at specific scales.

Conference Paper↗
USGS2024

Mapping the resistivity structure of Walker Ridge 313 in the Gulf of Mexico using the marine CSEM method

A marine controlled source electromagnetic (CSEM) campaign was carried out in the Gulf of Mexico to further develop marine electromagnetic techniques in order to aid the detection and mapping of gas hydrate deposits. Marine CSEM methods are used to obtain an electrical resistivity structure of the subsurface which can indicate the type of substance filling the pore space, such as gas hydrates which are more resistive. Results from the Walker Ridge 313 study (WR 313) are presented in this paper and compared with the Gulf of Mexico Gas Hydrate Joint Industry Project II (JIP2) logging while drilling (LWD) results and available seismic data. The hydrate, known to exist within sheeted sand deposits, is mapped as a resistive region in the two dimensional (2D) CSEM inversion models. This is consistent with the JIP2 LWD resistivity results. CSEM inversions that use seismic horizons provide more realistic results compared to the unconstrained inversions by providing sharp boundaries and architectural control on the location of the resistive and conductive regions in the CSEM model. The seismic horizons include: 1) the base of the gas hydrate stability zone (BGHSZ), 2) the top of salt, and 3) the top and bottom of a fine grained marine mud interval with near vertical hydrate filled fractures, to constrain the CSEM inversion model. The top of salt provides improved location for brines, water saturated salt, and resistive salt. Inversions of the CSEM data map the occurrence of a ‘halo’ of conductive brines above salt. The use of the BGHSZ as a constraint on the inversion helps distinguish between free gas and gas hydrate as well as gas hydrate and water saturated sediments.

Louisiana↗
USGS2026

Utilization of multiple geochronology techniques to constrain the age of laterization and mineralization of the world-class Mount Weld rare earth element deposit, Western Australia

Pervasive chemical weathering on stable cratons may form thick regoliths and elemental enrichment, but constraining the age of regolith formation is challenging. In this study we utilize multiple geochronological techniques on different minerals from the world-class Mount Weld rare earth element (REE) deposit, formed by lateritic weathering of a carbonatite, to constrain the age of formation and provide insight into landscape evolution. The oldest dates, ca. 100 to 38 Ma, are from Lu-Hf dating of churchite [HREE(PO 4 )·2(H 2 O)], a heavy REE phosphate mineral. Growth bands on individual minerals show a younging outwards. 40 Ar/ 39 Ar geochronology of cryptomelane [K(Mn 4+ ,Mn 2+ )₈O₁₆] yielded dates from ca. 40 to 27 Ma. Similarly, (U-Th)/He geochronology of goethite [FeO(OH)] yielded dates ranging from ca. 45 to 19 Ma. Integrating results into regional constraints, suggests 1) churchite formed by mineral saturation in a karst-like setting below the water table from ca. 100 to 40 Ma, 2) with minor uplift and erosion, cryptomelane and goethite formed at or near the water table between ca. 45 and 19 Ma, 3) after ca. 15 to 10 Ma chemical weathering within the profile had ended. Other studies document that the region experienced minimal uplift and a wet, warm climate from ca. 100 Ma to 15 Ma. These conditions and the high carbonate content of the carbonatite promote extensive chemical weathering, a deep weathering profile, and the preservation of the weathered section. This study highlights the use of multiple geochronological techniques utilizing different minerals to provide insight into how laterites form and to constrain the timing and history of the formation of this important mineral deposit.

Western Australia↗
USGS2025

Special issue "Effects of surface geology on seismic motion (ESG): General state-of-research"

To understand and predict the behaviors of strong ground motions incurred during devastating earthquakes, studies focused on the “effects of surface geology (ESG) on seismic motions” (following tradition, herein contracted as: “ESG”) have progressed steadily in the last three decades. These ESG studies typically involve in situ measurements of the wavefield and commonly apply both analytical and computational approaches. Concurrently, improvements in ESG related research can be readily attributed to the proliferation of openly accessible strong motion data, as well as advances in computational power. Nevertheless, there remain significant shortfalls in our understanding of the epistemic and aleatory uncertainties associated with the ESG as demonstrated by phenomena from recent deadly earthquake-related site effects. Thus, investigations toward addressing these deficiencies should be underscored in future earthquake related disaster mitigation efforts. This special issue of Earth, Planets, and Space (EPS) is dedicated to the ongoing efforts by the International Association of Seismology and Physics of the Earth’s Interior (IASPEI) and the International Association of Earthquake Engineering (IAEE) that champion activities promoting studies related to the ESG.

Earth, Planets and Space↗
USGS2025

Hydrogeologic framework and considerations for drilling and grouting of closed-loop geothermal bores in the Erie-Ontario Lowlands and Allegheny Plateau of New York State

The hydrogeologic framework at closed-loop geothermal sites in the Erie-Ontario Lowlands and Allegheny Plateau of central and western New York is the result of the complex interaction of bedrock geology, glacial geology, and groundwater hydrology, and the occurrence of petroleum and gas. Considerations for closed-loop geothermal bore installation include the thickness and character of glacial deposits, bedrock solubility and depth to competent rock, karst development, the distribution of highly permeable zones and their hydraulic heads, and the presence of saline water, gas, and oil. The hydrogeology of the Erie-Ontario Lowlands and Allegheny Plateau poses challenges to closed-loop geothermal bore drilling and casing; managing drill cuttings, discharge water, and gas; and grouting. The potential to encounter severe challenges typically increases with bore depth. This report highlights hydrogeologic considerations for closed-loop geothermal bore installation in New York’s Erie-Ontario Lowlands and Allegheny Plateau to help guide the efficient and safe development of geothermal resources in the regions.

New York↗
USGS2024

Evaluation of an open earthquake early warning system in Mexico, and laboratory tests of their sensors

Microelectromechanical system (MEMS) accelerometers are useful for seismological and engineering applications because of their ability to record unsaturated large seismic signals. Recent advances in MEMS technologies enable the design of instruments with improved capabilities that also allow the recording of small signals. As a result, MEMS can be useful across a broad dynamic range and for both major earthquakes and smaller magnitude events. Here, we analyze the performance of a MEMS‐based accelerometer with the capability of real‐time data transmission. We discuss the self‐noise level, dynamic range, and sensitivity, along with the timing precision and data transmission latency, and compare these parameters to other MEMS‐based instruments. We also summarize observations from a regional network deployed in southern Mexico over a period of 3+ yr for the purpose of earthquake early warning. In addition to the sensor evaluation, we present a large, openly available data set of strong motion data from the Mexican network that comprises continuous ground‐motion records from 24 accelerometers in the period between 2017 and 2022.

Seismological Research Letters↗
USGS2025

Relations of groundwater quality to long-term surface disposal of produced water near the Midway-Sunset and Buena Vista Oil Fields, California, USA

Contamination of groundwater by oil-field fluids in proximity to oil and gas development has been an issue of concern to water users and regulators given long histories of development and legacy disposal practices. A robust set of geochemical tracers including petroleum hydrocarbon compounds, thermogenic gases, inorganic ion concentrations, stable isotopes, radioactive isotopes, and noble gases were used to assess if oil-field fluids mixed with groundwater near the Midway-Sunset and Buena Vista Oil Fields in California, USA. Results show evidence of mixing of oil-field fluids with groundwater within the study area from either anthropogenic or natural processes. Produced water plumes associated with modern surface disposal facilities, used since the late 1950s, extend up to 1.5 km and currently remain within the boundaries of the oil fields. Plumes associated with earlier routing of produced water down natural drainages and in large retention structures (Midway Basin and Sunset Basin) near the Buena Vista Lake Bed are present in groundwater east of the oil fields. Based on geochemical tracer evidence, aerial imagery, and aerial electromagnetic surveys, these legacy plumes reach the western portion of the Central Valley aquifer system, an important groundwater resource for agricultural and domestic supply. The legacy plume associated with Sunset Basin may further be detected downgradient in deeper groundwater beneath the southern extent of the Buena Vista Lake Bed based on the presence of thermogenic gases and petroleum hydrocarbon compounds.

California↗
USGS2024

Beyond the wedge: Impact of tidal streams on salinization of groundwater in a coastal aquifer stressed by pumping and sea-level rise

Saltwater intrusion (SWI) is a well-studied phenomenon that threatens the freshwater supplies of coastal communities around the world. The development and advancement of numerical models has led to improved assessment of the risk of salinization. However, these studies often fail to include the impact of surface waters as potential sources of aquifer salinity and how they may impact SWI. Based on field-collected data, we developed a regional, variable-density groundwater model using SEAWAT for east Dover, Delaware. In this location, major users of groundwater from the surficial aquifer are the City of Dover and irrigation for agriculture. Our model includes salinized marshland and tidal streams, along with irrigation and municipal pumping wells. Model scenarios were run for 100 years and included changes in pumping rates and sea-level rise (SLR). We examined how these drivers of SWI affect the extent and location of salinization in the surficial aquifer by evaluating differences in chloride concentration near surface waters and the subsurface freshwater-saltwater interface. We found the presence of the marsh inverts the typical freshwater-saltwater wedge interface and that the edge of the interface did not migrate farther inland. Additionally, we found that tidal streams are the dominant pathways of SWI at our site with salinization from streams being exacerbated by SLR. Our results also show that spatial distribution of pumping affects both the magnitude and extent of salinization, with an increase in concentrated pumping leading to more intensive salinization than a more widely distributed increase of the same total pumping volume.

Delaware↗
USGS2026

Mineral chemistry perspective on remobilization of stored magma at Kamakai'a Hills, Southwest Rift Zone of Kilauea, Island of Hawai'i, USA

Differentiated magmas stored in the rift zones of Kīlauea have received more attention in recent years following eruption of andesite during the early phase of 2018 lower East Rift Zone activity. Despite this growing interest, some of the most voluminous eruptions of differentiated rift zone magmas remain poorly studied. One such eruption, and the most voluminous exposed differentiated flow field at Kīlauea, is the Kamakaiʻa Hills. This eruption took place in the Southwest Rift Zone of Kīlauea, a region that is hypothesized to contain a long-lived rift zone reservoir. The Kamakaiʻa Hills flow field encompasses >250 × 10 6 m 3 of basaltic andesite and basalt compositions with a mineral assemblage of orthopyroxene + clinopyroxene + plagioclase during its early ʻaʻā phase and clinopyroxene + plagioclase + olivine during its late pāhoehoe phase. To better understand storage conditions and magma accumulation, this study focuses on major, minor, and trace elements from the mineral assemblage present within the early ʻaʻā and late pāhoehoe phases. The diversity of clinopyroxene and plagioclase compositions within the early ʻaʻā and late pāhoehoe phases, as well as diverse compositions of plagioclase and orthopyroxene within the early ʻaʻā phase, suggest multiple magma bodies and limited pre-eruption magma mixing within the broader Kamakaiʻa Hills reservoir. Oscillatory zoning patterns (particularly in clinopyroxene) imply processes such as recharge events, magma mixing or mingling, or convection within a differentially cooling, chemically stratified reservoir over protracted time intervals, whereas only limited resorbed mineral textures indicate incomplete mixing of heat and chemically distinct magmas during the dike intrusion that triggered the eruption. Mineral-mineral and mineral-melt thermobarometry indicate predominantly shallow (≤2.5 km depth) crustal storage conditions of the cooled, differentiated magma (∼1100 °C and cooler for the basaltic andesites) to hotter temperatures for the basalts (all >1100 °C). Despite the known large standard errors estimated for mineral-melt and mineral-mineral barometry (10s to >100 MPa), the calculated pressures and depths broadly correspond with earthquake swarm depths beneath the Kamakaiʻa Hills, and drill core and fluid inclusion barometry storage depths of differentiated magmas within the lower East Rift Zone. The Kamakaiʻa Hills differentiated magmas have H 2 O contents (∼0.5 wt%, using plagioclase-melt hygrometry) equivalent to typical Kīlauea basalts. Our data and interpretations demonstrate a complex, long-lived rift zone storage system that consisted of multiple magma bodies and was mobilized into eruption through intrusion of a hotter and more primitive summit-derived (uprift) magma.

Hawaii↗