USGS Science⌕ Search

SEARCH · USGS Science

Results for “Topographic Map”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29Linked to original sources
USGS1965

Resource understanding: a challenge to aerial methods

Aerial survey methods are speeding acquisition of survey data needed to provide and manage the nation's resources. These methods have been applied to topographic mapping for a number of years and the record clearly shows their advantages in terms of cost and speed in contrast to the ground methods that have been historically employed. Limited use is now being made of aerial methods to assist cadastral surveys, in location, acquisition and development of National Parks, in mapping the geology of the nation, in locating and developing water resources, and in surveys of the oceans. It is the purpose of this paper to call attention to these uses and to encourage the scientific community to further refine aerial methods so that their use may be increased and the veracity of data improved.

Photogrammetric Engineering↗
USGS1976

Thermographic mosaic of Yellowstone National Park

An uncontrolled thermographic mosaic, which covers most of the area of Yellowstone National Park, has been compiled. The recording of aerial thermographic data on videotape is established as one of the prerequisites for the preparation of more accurate mosaics. Post-mission processing of the videotape record can rectify the nadir line to a topographic map base, correct for v/h variations in adjacent flight lines, correct for yaw distortions, rectify distortions caused by pitch, and rectify distortions produced by non-linearity of the side-wise scan. Installation of a thermal infrared scanning radiometer in a gyrostabilized mount and post-mission processing of the videotape record (principally rectification of side-wise scan distortion) would yield a controlled, photogrammetrically accurate thermographic mosaic. However, the techniques used in the preparation of the uncontrolled thermographic mosaic of Yellowstone National Park can be immediately applied to the preparation of regional thermographic mosaics, important to geologists and other scientists and engineers in studies of geothermal and volcanic areas, and to other types of environmental investigations such as pollution studies of large water bodies (e.g., harbors, estuaries, lakes, etc.), where a precise planimetric image is not critical.

Idaho;Montana;Wyoming↗
USGS1978

Applying satellite technology to energy and mineral exploration

IGCP Project 143 ("Remote Sensing and Mineral Exploration"), is a worldwide research project designed to make satellite data an operational geological tool along with the geologic pick, hand lens, topographic map, aerial photo and geophysical instruments and data that comprise the exploration package. While remote sensing data will not replace field exploration and mapping, careful study of such data prior to field work should make the effort more efficient.

Episodes↗
USGS1980

Integration of geological, geochemical, and geophysical spatial data of the Cement oil field, Oklahoma, test site

Measurement pertaining to geology, geochemistry, and geophysics of the Cement oil field, Oklahoma, test site were collected employing both airborne sensors and ground-based data collection. The measurements include: (1) airborne gamma-ray spectrometry (supplying bismuth 214, thalium 208, and potassium 40 gamma-ray intensities); (2) aeromagnetic survey data; (3) multi-frequency airborne resistivity survey data (supplying apparent electrical resistivity of near surface materials); (4) gravity data; (5) geological and topographic maps; and (6) image data from Landsat MSS and U-2 photography.

Oklahoma↗
USGS1989

Investigations of SPOT cartographic applications in the U.S. Geological Survey

The US Geological Survey has a longstanding commitment to the advancement of the technology and applications of remotely sensed data from civilian satellite systems. In the past, research based on satellite data was primarily directed toward natural resource and land use applications rather than cartographic applications. The availability of high-resolution, steroscopic data from the sensors on SPOT provides new opportunities for cartographic applications. The potential applications include production of satellite image and topographic maps, and generation of digital elevation data.

CISM Journal ACSGC↗
USGS1973

Stream-profile analysis and stream-gradient index

The generally regular three-dimensional geometry of drainage networks is the basis for a simple method of terrain analysis providing clues to bedrock conditions and other factors that determine topographic forms. On a reach of any stream, a gradient-index value can be obtained which allows meaningful comparisons of channel slope on streams of different sizes. The index is believed to reflect stream power or competence and is simply the product of the channel slope at a point and channel length measured along the longest stream above the point where the calculation is made. In an adjusted topography, changes in gradient-index values along a stream generally correspond to differences in bedrock or introduced load. In any landscape the gradient index of a stream is related to total relief and stream regimen. Thus, climate, tectonic events, and geomorphic history must be considered in using the gradient index. Gradient-index values can be obtained quickly by simple measurements on topographic maps, or they can be obtained by more sophisticated photogrammetric measurements that involve simple computer calculations from x, y, z coordinates.

Journal of Research of the U.S. Geological Survey↗
USGS2011

The Hydrogeology of the San Juan Mountains Chapter 5

Knowledge of the occurrence, storage, and flow of groundwater in mountainous regions is limited by the lack of integrated data from wells, streams, springs, and climate. In his comprehensive treatment of the hydrogeology of the San Luis Valley, Huntley (1979) hypothesized that the underlying, fractured volcanic bedrock of the San Juan Mountains has relatively high bulk permeability and a regional-scale water table with a low hydraulic gradient. Other (some more recent) studies of fractured crystalline bedrock in mountainous terrain indicate that these rock units can act as aquifers (Kahn et al. 2008; Manning and Caine 2007; Robinson 1978; Stober and Bucher 2005). The body of recent work also suggests that the conception that fractured crystalline bedrock is of such low permeability that it constitutes a “no-flow zone” may be inappropriate. In addition to establishing a new baseline, the data presented here are used to test Huntley’s (1979) hypotheses that suggest that the San Juan Mountains may be underlain by a substantial groundwater system. With the advent of computers and digital databases, many types of publicly available data can be used to test hypotheses and provide new insights into mountain hydrogeology at the regional scale in the San Juan Mountains. Plate 16 illustrates processes that suggest several fundamental questions arising from our lack of knowledge of mountain hydrogeology. These questions include: What are the dynamic interrelationships among the tectonics of mountain building, climate, and groundwater, and what are the time scales over which associated processes operate? How does extreme topographic relief allow for groundwater recharge along steep surfaces rather than simply causing precipitation to run off ? How does extreme relief translate into hydraulic gradients that drive groundwater flow? Can extreme gradients drive large volumes of meteoric water deep into the Earth’s upper crust? Once in the subsurface, what are the residence times of these waters? Finally, how does complex geology, commonly associated with mountainous terrain, influence these processes and control potentially heterogeneous and tortuous flow pathways? This chapter presents a synthesis of hydrogeological data, in a reconnaissance style, at the regional scale for the San Juan Mountains. Analyses of these data shed some light on the questions posed earlier for the San Juan Mountains and on mountain hydrogeologic processes in general. These analyses are based on public digital data from geologic and topographic maps, precipitation networks, stream gauges, groundwater wells, and springs. These data can be integrated using the hydrologic cycle expressed as a mass balance between inputs and outputs. The data types noted earlier form the basic set of measurements used to explore, characterize, and quantify elements of the hydrologic cycle. This exploration at a variety of scales yields insight into the relationships among the physical geological framework, climatological and hydrological budgets, and the hydraulic properties of the major aquifers in the San Juan Mountains. Each of these factors has been broken down and investigated separately and then integrated at the end of the chapter, using a conceptual model. Although the San Juan Mountains contain extensive precious- and base-metal deposits that have led to natural and mining-related groundwater contamination, this topic is not addressed here. Interested readers should refer to the extensive body of US Geological Survey work in Gray et al. (1994), Plumlee et al. (1995), Wirt et al. (1999), Johnson and Yager (2006), Johnson et al. (2007), and Church, von Guerard, and Finger (2007). Huntley (1979) also provided a large database for regional hydro-geochemistry of the San Juan Mountains (SJM).

Colorado↗
USGS1969

Reconnaissance of the ground-water resources of the upper Fremont River valley, Wayne County, Utah

This report presents the results of an investigation of the ground-water resources of the upper Fremont River valley, Utah, which was carried out during the period July 1966-June 1967, by the U.S. Geological Survey in cooperation with the Utah Department of Natural Resources, Division of Water Rights. The purpose of the investigation was to determine: the source, occurrence, availability, approximate quantity, movement, and chemical quality of ground water in the valley; the recharge to and discharge from the ground-water reservoir; the extent and effects of use and development on the ground-water resources; the relation of ground water to streamflow; and if and where additional studies are needed. The report is concerned primarily with ground water in the valley fill and adjacent volcanic rocks and secondarily with the general hydrology of the upper Fremont River valley drainage basin. The field investigation was made mostly during the summer and fall of 1966. Data were collected for 63 wells and 16 springs in the valley. Records for wells and springs are given in table 4; drillers' logs of selected wells are given in table 5, and well locations are shown in figure 5. All the wells (except a few small-discharge wells) and all major springs were visited. The specific conductance of water was determined at most wells and springs; chemical analyses were made of water from selected wells and springs. Conductance data are included in table 4 and chemical analyses are given in table 6. The yield of water from wells and the water levels or artesian pressures were measured or estimated. Water-level measurements were made at monthly intervals 6 at 10 selected wells. Altitudes of the land surface at wells and springs were estimated from topographic maps or by hand leveling or determined by altimeter. Aerial photographs were used in the field to locate wells, boundaries of meadows or cultivated areas, edge of valley fill, and other features.

Utah↗
USGS1899

Geology and mining industry of the Tintic district, Utah: Section in Nineteenth Annual Report of the United States Geological Survey to the Secretary of the Interior 1897 - 1898: Part III - Economic Geology

The field work upon which this report is based was begun in July, 1897, and continued without interruption until December of the same year. The area studied is approximately 15 miles square and contains 234 square miles. The topographic maps, which are two in number, were prepared under the direction of Mr. R. U. Goode, Mr. S. S. Gannett doing the triangulation and Messrs. Marshall and Griswold the topography in the fall of 1896 and summer of 1897. The mapping is done on two scales; the larger area, approximately 15 miles square, is mapped on a scale of 1: 62,500. This map is designed to form a part of the Geologic Atlas of the United States. The other map represents the portion of the larger area in which the majority of the mines are located. It is on a scale of 1: 9,600, and covers an area of 12 square miles. The work has been greatly facilitated through the assistance rendered by the mining men of the district, among whom special thanks are due to Messrs. G. H. Robinson, W. J. Craig, W. M. Nesbit, and C. H. Blanchard. The chemical work on the ores and country rocks from the district has been done in the laboratory of the Survey by Messrs. H. N. Stokes and George Steiger, and the determination of the fossils collected is to be credited to Mr. G. H. Girty, also of the Geological Survey. In the field work the authors have cooperated constantly on every phase of the varied problems. The same is true for the office work, except that the stratigraphic and economic problems have been the especial studies of Mr. Tower, while the petrologic and remaining problems have been the special studies of Mr. Smith. In pursuance of this system of work the introduction has been written conjointly, Chapter II of Part I and all of Part II have been written by Mr. Tower, and Chapters I and III to VII of Part I by Mr. Smith.

Utah↗
USGS2016

High performance computing to support multiscale representation of hydrography for the conterminous United States

The National Hydrography Dataset (NHD) for the United States furnishes a comprehensive set of vector features representing the surface-waters in the country (U.S. Geological Survey 2000). The high-resolution (HR) layer of the NHD is largely comprised of hydrographic features originally derived from 1:24,000-scale (24K) U.S. Topographic maps. However, in recent years (2009 to present) densified hydrographic feature content, from sources as large as 1:2,400, have been incorporated into some watersheds of the HR NHD within the conterminous United States to better support the needs of various local and state organizations. As such, the HR NHD is a multiresolution dataset with obvious data density variations because of scale changes. In addition, data density variations exist within the HR NHD that are particularly evident in the surface-water flow network (NHD flowlines) because of natural variations of local geographic conditions; and also because of unintentional compilation inconsistencies due to variations in data collection standards and climate conditions over the many years of 24K hydrographic data collection (US Geological Survey 1955).

Conference Paper↗
USGS2006

The HRSC DTM test

The High Resolution Stereo Camera (HRSC) has been orbiting the planet Mars since January 2004 onboard the ESA Mars Express mission and delivers imagery which is being used for topographic mapping of the planet. The HRSC team is currently conducting a systematic inter-comparison of different alternatives for the production of high resolution Digital Terrain Models (DTMs) from the multilook HRSC push broom imagery. Based on carefully chosen test sites the test participants have produced DTMs which have been subsequently analysed in a quantitative and a qualitative manner. This paper reports on the results obtained in this test.

Conference Paper↗
USGS1978

Remote-sensing methods for monitoring surface coal mining in the northern Great Plains

Recent studies at a large surface coal mine in southern Montana confirm that remote sensing is both feasible and effective for gathering land-use and environmental data (spatial, dynamic, and seasonal) for large-scale surface mines in the northern Great Plains. The Western Energy Co.'s Rosebud mine near Colstrip, Mont., was selected as a test site because it typifies surface operations in the Powder River Basin of Montana and Wyoming and elsewhere in the northern Great Plains. Several basic interpretive and analytical remote-sensing techniques were used to identify and delineate various categories of surface-mining operations and concurrent stages of reclamation that characterize most, if not all, such mining operations. Color infrared and black-and-white aerial photographs and a black-and-white band 5 Landsat image were used to identify (1) high wall and bench areas, (2) ungraded spoils, (3) graded and recontoured areas, (4) revegetated recontoured areas, (5) natural and impounded surface water, and (6) miscellaneous areas. Over the lifespan of an extensive surface mine, cultural and natural processes and cumulative environmental effects can be monitored by capitalizing on the close correlation between enhanced satellite imagery, infrared and (or) black-and-white aerial photography, standard large-scale topographic maps (such as U.S. Geological Survey 7½-minute quadrangle maps), and results of onsite inspection of mining and reclamation by Federal or State agencies.

Montana↗
USGS2016

Using satellite vegetation and compound topographic indices to map highly erodible cropland buffers for cellulosic biofuel crop developments in eastern Nebraska, USA

Cultivating annual row crops in high topographic relief waterway buffers has negative environmental effects and can be environmentally unsustainable. Growing perennial grasses such as switchgrass ( Panicum virgatum L.) for biomass (e.g., cellulosic biofuel feedstocks) instead of annual row crops in these high relief waterway buffers can improve local environmental conditions (e.g., reduce soil erosion and improve water quality through lower use of fertilizers and pesticides) and ecosystem services (e.g., minimize drought and flood impacts on production; improve wildlife habitat, plant vigor, and nitrogen retention due to post-senescence harvest for cellulosic biofuels; and serve as carbon sinks). The main objectives of this study are to: (1) identify cropland areas with high topographic relief (high runoff potentials) and high switchgrass productivity potential in eastern Nebraska that may be suitable for growing switchgrass, and (2) estimate the total switchgrass production gain from the potential biofuel areas. Results indicate that about 140,000 hectares of waterway buffers in eastern Nebraska are suitable for switchgrass development and the total annual estimated switchgrass biomass production for these suitable areas is approximately 1.2 million metric tons. The resulting map delineates high topographic relief croplands and provides useful information to land managers and biofuel plant investors to make optimal land use decisions regarding biofuel crop development and ecosystem service optimization in eastern Nebraska.

Nebraska↗
USGS1975

Relations between thermal, photographic, and topographic linears and mapped and measured structures in a Precambrian terrane in Colorado

Comparison of orientation of faults, foliations, and joints, observed during geologic mapping in Colorado, with thermal, photographic, and topographic linears shows that topographic linears are statistically useful indicators of mappable faults and fractures, photographic linears are less useful, and thermal linears, believed to represent zones of moisture concentration, are parallel to faults, foliations, and, a statistically minor, but more open joint set.

Colorado↗
USGS1909

The topographic and geologic atlas of the United States

The Geological Survey is making a topographic and geologic map of the United States. The topographic map is being published in separate sheets and the geologic map in parts called folios. Each folio includes a topographic map and geologic maps of a small area, together with explanatory and descriptive text. Beginning with No. 164 the geologic folios are issued in two forms, the octavo or field edition and the folio or library edition.

Report↗
USGS2009

THEMIS high-resolution digital terrain: Topographic and thermophysical mapping of Gusev Crater, Mars

We discuss a new technique to generate high-resolution digital terrain models (DTMs) and to quantitatively derive and map slope-corrected thermophysical properties such as albedo, thermal inertia, and surface temperatures. This investigation is a continuation of work started by Kirk et al. (2005), who empirically deconvolved Thermal Emission Imaging System (THEMIS) visible and thermal infrared data of this area, isolating topographic information that produced an accurate DTM. Surface temperatures change as a function of many variables such as slope, albedo, thermal inertia, time, season, and atmospheric opacity. We constrain each of these variables to construct a DTM and maps of slope-corrected albedo, slope- and albedo-corrected thermal inertia, and surface temperatures across the scene for any time of day or year and at any atmospheric opacity. DTMs greatly facilitate analyses of the Martian surface, and the MOLA global data set is not finely scaled enough (128 pixels per degree, ???0.5 km per pixel near the equator) to be combined with newer data sets (e.g., High Resolution Imaging Science Experiment, Context Camera, and Compact Reconnaissance Imaging Spectrometer for Mars at ???0.25, ???6, and ???20 m per pixel, respectively), so new techniques to derive high-resolution DTMs are always being explored. This paper discusses our technique of combining a set of THEMIS visible and thermal infrared observations such that albedo and thermal inertia variations within the scene are eliminated and only topographic variations remain. This enables us to produce a high-resolution DTM via photoclinometry techniques that are largely free of albedo-induced errors. With this DTM, THEMIS observations, and a subsurface thermal diffusion model, we generate slope-corrected maps of albedo, thermal inertia, and surface temperatures. In addition to greater accuracy, these products allow thermophysical properties to be directly compared with topography.

Journal of Geophysical Research E: Planets↗