Geology topics

Paul F. Juckem

Publications and source records attributed to Paul F. Juckem.

26 records · Page 2Linked to original sources

USGS2010

Simulation of the shallow groundwater-flow system near the Hayward Airport, Sawyer County, Wisconsin

There are concerns that removal and trimming of vegetation during expansion of the Hayward Airport in Sawyer County, Wisconsin, could appreciably change the character of a nearby cold-water stream and its adjacent environs. In cooperation with the Wisconsin Department of Transportation, a two-dimensional, steady-state groundwater-flow model of the shallow groundwater-flow system near the Hayward Airport was refined from a regional model of the area. The parameter-estimation code PEST was used to obtain a best fit of the model to additional field data collected in February 2007 as part of this study. The additional data were collected during an extended period of low runoff and consisted of water levels and streamflows near the Hayward Airport. Refinements to the regional model included one additional hydraulic-conductivity zone for the airport area, and three additional parameters for streambed resistance in a northern tributary to the Namekagon River and in the main stem of the Namekagon River. In the refined Hayward Airport area model, the calibrated hydraulic conductivity was 11.2 feet per day, which is within the 58.2 to 7.9 feet per day range reported for the regional glacial and sandstone aquifer, and is consistent with a silty soil texture for the area. The calibrated refined model had a best fit of 8.6 days for the streambed resistance of the Namekagon River and between 0.6 and 1.6 days for the northern tributary stream. The previously reported regional groundwater-recharge rate of 10.1 inches per year was adjusted during calibration of the refined model in order to match streamflows measured during the period of extended low runoff; this resulted in an optimal groundwater-recharge rate of 7.1 inches per year during this period. The refined model was then used to simulate the capture zone of the northern tributary to the Namekagon River.

Scientific Investigations Report↗

USGS2009

Simulation of the Groundwater-Flow System in Pierce, Polk, and St. Croix Counties, Wisconsin

Groundwater is the sole source of residential water supply in Pierce, Polk, and St. Croix Counties, Wisconsin. A regional three-dimensional groundwater-flow model and three associated demonstration inset models were developed to simulate the groundwater-flow systems in the three-county area. The models were developed by the U.S. Geological Survey in cooperation with the three county governments. The objectives of the regional model of Pierce, Polk, and St. Croix Counties were to improve understanding of the groundwaterflow system and to develop a tool suitable for evaluating the effects of potential water-management programs. The regional groundwater-flow model described in this report simulates the major hydrogeologic features of the modeled area, including bedrock and surficial aquifers, groundwater/surface-water interactions, and groundwater withdrawals from high-capacity wells. Results from the regional model indicate that about 82 percent of groundwater in the three counties is from recharge within the counties; 15 percent is from surface-water sources, consisting primarily of recirculated groundwater seepage in areas with abrupt surface-water-level changes, such as near waterfalls, dams, and the downgradient side of reservoirs and lakes; and 4 percent is from inflow across the county boundaries. Groundwater flow out of the counties is to streams (85 percent), outflow across county boundaries (14 percent), and pumping wells (1 percent). These results demonstrate that the primary source of groundwater withdrawn by pumping wells is water that recharges within the counties and would otherwise discharge to local streams and lakes. Under current conditions, the St. Croix and Mississippi Rivers are groundwater discharge locations (gaining reaches) and appear to function as 'fully penetrating' hydraulic boundaries such that groundwater does not cross between Wisconsin and Minnesota beneath them. Being hydraulic boundaries, however, they can change in response to water withdrawals. Tributary rivers act as 'partially penetrating' hydraulic boundaries such that groundwater can flow underneath them through the deep sandstone aquifers. The model also demonstrates the effects of development on groundwater in the study area. Water-level declines since predevelopment (no withdrawal wells) are most pronounced where pumping is greatest and flow between layered aquifers is impeded by confining units or faults. The maximum simulated water-level decline is about 40 feet in the deep Mount Simon aquifer below the city of Hudson, Wisconsin. Three inset models were extracted from the regional model to demonstrate the process and additional capabilities of the U.S. Geological Survey MODFLOW code. Although the inset models were designed to provide information about the groundwater-flow system, results from the inset models are presented for demonstration purposes only and are not sufficiently detailed or calibrated to be used for decisionmaking purposes without refinement. Simulation of groundwater/lake-water interaction around Twin Lakes near Roberts, in St. Croix County, Wisconsin, showed that groundwater represents approximately 5 to 20 percent of the overall lake-water budget. Groundwater-contributing areas to streams in western Pierce County are generally similar in size to the surface-water-contributing areas but do not necessarily correspond to the same land area. Transient streamflow simulations of Osceola Creek in Polk County demonstrate how stream base flow can be influenced not only by seasonal precipitation and recharge variability but also by systematic changes to the system, such as groundwater withdrawal from wells.

Scientific Investigations Report↗

USGS2009

Water Quality and Hydrology of Whitefish (Bardon) Lake, Douglas County, Wisconsin, With Special Emphasis on Responses of an Oligotrophic Seepage Lake to Changes in Phosphorus Loading and Water Level

Whitefish Lake, which is officially named Bardon Lake, is an oligotrophic, soft-water seepage lake in northwestern Wisconsin, and classified by the Wisconsin Department of Natural Resources as an Outstanding Resource Water. Ongoing monitoring of the lake demonstrated that its water quality began to degrade (increased phosphorus and chlorophyll a concentrations) around 2002 following a period of high water level. To provide a better understanding of what caused the degradation in water quality, and provide information to better understand the lake and protect it from future degradation, the U.S. Geological Survey did a detailed study from 2004 to 2008. The goals of the study were to describe the past and present water quality of the lake, quantify water and phosphorus budgets for the lake, simulate the potential effects of changes in phosphorus inputs on the lake's water quality, analyze changes in the water level in the lake since 1900, and relate the importance of changes in climate and changes in anthropogenic (human-induced) factors in the watershed to the water quality of the lake. Since 1998, total phosphorus concentrations increased from near the 0.005-milligrams per liter (mg/L) detection limit to about 0.010 mg/L in 2006, and then decreased slightly in 2007-08. During this time, chlorophyll a concentrations and Secchi depths remained relatively stable at about 1.5 micrograms per liter (ug/L) and 26 feet, respectively. Whitefish Lake is typically classified as oligotrophic. Because the productivity in Whitefish Lake is limited by phosphorus, phosphorus budgets were constructed for the lake. Because it was believed that much of its phosphorus comes from the atmosphere, phosphorus deposition was measured in this study. Phosphorus input from the atmosphere was greater than computed based on previously reported wetfall phosphorus concentrations. The concentrations and deposition rates can be used to estimate atmospheric loading in future lake studies. The average annual load of phosphorus to the lake was 232 pounds: 56 percent from precipitation, 27 percent from groundwater, and 16 percent from septic systems. During a series of dry years (low water levels) and wet years (high water levels), the inputs of water and phosphorus ranged by only 10-13 percent. Results from the Canfield and Bachmann eutrophication model and Carlson trophic-state-index equations demonstrated that the lake directly responds to changes in external phosphorus loading, with percent change in chlorophyll a being similar to the percent change in loading and the change in total phosphorus and Secchi depth being slightly smaller. Therefore, changes in phosphorus loading should affect the water quality of the lake. Specific scenarios that simulated the effects of anthropogenic (human-induced) and climatic (water level) changes demonstrated that: surface-water inflow (runoff) based on current development has little effect on pelagic water quality, changes in the inputs from septic systems and development in the watershed could have a large effect on water quality, and decreases in water and phosphorus loading during periods of low water level had little effect on water quality. Sustained high water levels, resulting from several wet years with relatively high water and phosphorus input, however, could cause a small degradation in water quality. Although high water levels may be associated with a degradation in water quality, it appears that anthropogenic changes in the watershed may be more important in affecting the future water quality of the lake. Fluctuations in water levels since 1998 are representative of what has occurred since 1900, with fluctuations of about 3 feet occurring about every 15 years. Based on total phosphorus concentrations inferred from sediment core analysis, there has been little long-term change in water quality and there has been a slight deterioration in water quality following most periods of high water levels. There

Scientific Investigations Report↗

USGS2009

Simulation of the Regional Ground-Water-Flow System and Ground-Water/Surface-Water Interaction in the Rock River Basin, Wisconsin

A regional, two-dimensional, areal ground-water-flow model was developed to simulate the ground-water-flow system and ground-water/surface-water interaction in the Rock River Basin. The model was developed by the U.S. Geological Survey (USGS), in cooperation with the Rock River Coalition. The objectives of the regional model were to improve understanding of the ground-water-flow system and to develop a tool suitable for evaluating the effects of potential regional water-management programs. The computer code GFLOW was used because of the ease with which the model can simulate ground-water/surface-water interactions, provide a framework for simulating regional ground-water-flow systems, and be refined in a stepwise fashion to incorporate new data and simulate ground-water-flow patterns at multiple scales. The ground-water-flow model described in this report simulates the major hydrogeologic features of the modeled area, including bedrock and surficial aquifers, ground-water/surface-water interactions, and ground-water withdrawals from high-capacity wells. The steady-state model treats the ground-water-flow system as a single layer with hydraulic conductivity and base elevation zones that reflect the distribution of lithologic groups above the Precambrian bedrock and a regionally significant confining unit, the Maquoketa Formation. In the eastern part of the Basin where the shale-rich Maquoketa Formation is present, deep ground-water flow in the sandstone aquifer below the Maquoketa Formation was not simulated directly, but flow into this aquifer was incorporated into the GFLOW model from previous work in southeastern Wisconsin. Recharge was constrained primarily by stream base-flow estimates and was applied uniformly within zones guided by regional infiltration estimates for soils. The model includes average ground-water withdrawals from 1997 to 2006 for municipal wells and from 1997 to 2005 for high-capacity irrigation, industrial, and commercial wells. In addition, the model routes tributary base flow through the river network to the Rock River. The parameter-estimation code PEST was linked to the GFLOW model to select the combination of parameter values best able to match more than 8,000 water-level measurements and base-flow estimates at 9 streamgages. Results from the calibrated GFLOW model show simulated (1) ground-water-flow directions, (2) ground-water/surface-water interactions, as depicted in a map of gaining and losing river and lake sections, (3) ground-water contributing areas for selected tributary rivers, and (4) areas of relatively local ground water captured by rivers. Ground-water flow patterns are controlled primarily by river geometries, with most river sections gaining water from the ground-water-flow system; losing sections are most common on the downgradient shore of lakes and reservoirs or near major pumping centers. Ground-water contributing areas to tributary rivers generally coincide with surface watersheds; however the locations of ground-water divides are controlled by the water table, whereas surface-water divides are controlled by surface topography. Finally, areas of relatively local ground water captured by rivers generally extend upgradient from rivers but are modified by the regional flow pattern, such that these areas tend to shift toward regional ground-water divides for relatively small rivers. It is important to recognize the limitations of this regional-scale model. Heterogeneities in subsurface properties and in recharge rates are considered only at a very broad scale (miles to tens of miles). No account is taken of vertical variations in properties or pumping rates, and no provision is made to account for stacked ground-water-flow systems that have different flow patterns at different depths. Small-scale flow systems (hundreds to thousands of feet) associated with minor water bodies are not considered; as a result, the model is not currently designed for simulating site-specifi

Scientific Investigations Report↗

USGS2008

Simulation of contributing areas and surface-water leakage to potential replacement wells near the community of New Post, Sawyer County, Wisconsin, by means of a two-dimensional ground-water flow model

A two-dimensional, steady-state ground-water-flow model of the shallow ground-water-flow system near the community of New Post, Sawyer County, Wis., was refined from an existing model of the area. Hydraulic-conductivity and recharge values were not changed from the existing model for the scenario simulations described in this report. Rather, the model was refined by adding detail along the Chippewa Flowage and then was used to simulate contributing areas for three potential replacement wells pumping 30,000 gallons per day. The model also was used to simulate potential surface-water leakage out of the Chippewa Flowage captured by replacement-well pumping. A range in resistance to vertical ground-water flow was simulated along the Chippewa Flowage for each potential replacement-well location to bound the potential effects of representing three-dimensional flow with a two-dimensional model. Results indicate that pumping from a replacement well sited about 130 feet from the Chippewa Flowage could capture as much as 39 percent of the total pumping from the flowage. Pumping from either of two potential replacement wells sited at least 400 feet from the Chippewa Flowage did not induce surface-water leakage out of the flowage regardless of the resistance applied along the flowage for simulations described in this report.

Wisconsin↗

USGS2008

Ground-Water Flow in the Vicinity of the Ho-Chunk Nation Communities of Indian Mission and Sand Pillow, Jackson County, Wisconsin

An analytic element ground-water-flow model was constructed to help understand the ground-water-flow system in the vicinity of the Ho-Chunk Nation communities of Indian Mission and Sand Pillow in Jackson County, Wisconsin. Data from interpretive reports, well-drillers' construction reports, and an exploratory augering program in 2003 indicate that sand and gravel of varying thickness (0-150 feet[ft]) and porous sandstone make up a composite aquifer that overlies Precambrian crystalline rock. The geometric mean values for horizontal hydraulic conductivity were estimated from specific-capacity data to be 61.3 feet per day (ft/d) for sand and gravel, 6.6 ft/d for sandstone, and 12.0 ft/d for the composite aquifer. A ground-water flow model was constructed, the near field of which encompassed the Levis and Morrison Creeks Watershed. The flow model was coupled to the parameter-estimation program UCODE to obtain a best fit between simulated and measured values of ground-water levels and estimated Q50 flow duration (base flow). Calibration of the model with UCODE provided a ground-water recharge rate of 9 inches per year and a horizontal hydraulic conductivity of 13 ft/d for the composite aquifer. Using these calibrated parameter values, simulated heads from the model were on average within 5 ft of the measured water levels. In addition, these parameter values provided an acceptable base-flow calibration for Hay, Dickey, and Levis Creeks; the calibration was particularly close for Levis Creek, which was the most frequently measured stream in the study area. The calibrated model was used to simulate ground-water levels and to determine the direction of ground-water flow in the vicinity of Indian Mission and Sand Pillow communities. Backward particle tracking was conducted for Sand Pillow production wells under two pumping simulations to determine their 20-year contributing areas. In the first simulation, new production wells 6, 7, and 8 were each pumped at 50 gallons per minute (gal/min). In the second simulation, new production wells 6, 7, and 8 and existing production well 5 were each pumped at 50 gal/min. The second simulation demonstrated interference between the existing production well 5 and the new production wells when all were pumping at 50 gal/min.

Scientific Investigations Report↗

USGS2007

Simulation of the shallow ground-water-flow system near Grindstone Creek and the community of New Post, Sawyer County, Wisconsin

A two-dimensional, steady-state ground-water-flow model of Grindstone Creek, the New Post community, and the surrounding areas was developed using the analytic element computer code GFLOW. The parameter estimation code UCODE was used to obtain a best fit of the model to measured water levels and streamflows. The calibrated model was then used to simulate the effect of ground-water pumping on base flow in Grindstone Creek. Local refinements to the regional model were subsequently added in the New Post area, and local water-level data were used to evaluate the regional model calibration. The locally refined New Post model was also used to simulate the areal extent of capture for two existing water-supply wells and two possible replacement wells. Calibration of the regional Grindstone Creek simulation resulted in horizontal hydraulic conductivity values of 58.2 feet per day (ft/d) for the regional glacial and sandstone aquifer and 7.9 ft/d for glacial thrust-mass areas. Ground-water recharge in the calibrated regional model was 10.1 inches per year. Simulation of a golf-course irrigation well, located roughly 4,000 feet away from the creek, and pumping at 46 gallons per minute (0.10 cubic feet per second, ft3/s), reduced base flow in Grindstone Creek by 0.05 ft3/s, or 0.6 percent of the median base flow during water year 2003, compared to the calibrated model simulation without pumping. A simulation of peak pumping periods (347 gallons per minute or 0.77 ft3/s) reduced base flow in Grindstone Creek by 0.4 ft3/s (4.9 percent of the median base flow). Capture zones for existing and possible replacement wells delineated by the local New Post simulation extend from the well locations to an area south of the pumping well locations. Shallow crystalline bedrock, generally located south of the community, limits the extent of the aquifer and thus the southerly extent of the capture zones. Simulated steady-state pumping at a rate of 9,600 gallons per day (gal/d) from a possible replacement well near the Chippewa Flowage induced 70 gal/d of water from the flowage to enter the aquifer. Although no water-quality samples were collected from the Chippewa Flowage or the ground-water system, surface-water leakage into the ground-water system could potentially change the local water quality in the aquifer.

Wisconsin↗

USGS2007

Hydrogeologic characteristics of the St. Croix River basin, Minnesota and Wisconsin: Implications for the susceptibility of ground water to potential contamination

Population growth in the St. Croix River Basin in Minnesota and Wisconsin has intensified concerns of county resource managers and the National Park Service, which is charged with protecting the St. Croix National Scenic Riverway, about the potential for ground-water contamination in the basin. This report describes a previously developed method that was adapted to illustrate potential ground-water-contamination susceptibility in the St. Croix River Basin. The report also gives an estimate of ground-water-residence time and surface-water/ground-water interaction as related to natural attenuation and movement of contaminants in five tributary basins. A ground-water-contamination-susceptibility map was adapted from a state-wide map of Wisconsin to the St. Croix River Basin by use of well-driller construction records and regional maps of aquifer properties in Minnesota and Wisconsin. Measures of various subsurface properties were combined to generate a spatial index of susceptibility. The subjective index method developed for the State of Wisconsin by Schmidt (1987) 1 was not derived from analyses of water-quality data or physical processes. Nonetheless, it was adapted for this report to furnish a seamless map across state boundaries that would be familiar to many resource managers. Following this method, areas most susceptible to contamination appear to have coarse-grained sediments (sands or gravels) and shallow water tables or are underlain by carbonate-bedrock aquifers. The least susceptible areas appear to have fine-grained sediments and deep water tables. If an aquifer becomes contaminated, the ground-water-residence time can affect potential natural attenuation along the ground-water-flow path. Mean basin ground-water-residence times were computed for the Apple, Kettle, Kinnickinnic, Snake and Sunrise River Basins, which are tributary basins to the St. Croix Basin, by use of average aquifer properties of saturated thickness, porosity, and recharge rates. The Apple River Basin had the shortest mean ground-water-residence times (20–120 years), owing largely to the moderate saturated thickness and high recharge rate in the basin. The Kinnickinnic and Sunrise River Basins had the longest mean residence times (60–350 and 70–390 years, respectively) chiefly because of the relatively large saturated thickness of the basins. Owing to limitations of the residence-time calculations, actual ground-water-residence times will vary around the mean values within each basin and may range from days or weeks in karst carbonate aquifers to millennia in deep confined sandstone aquifers. Areas of relatively short residence time (less than the median residence time in each basin) were identified by use of ground-water-flow models for each of the five tributary basins. Results of simulations show that these areas, in which contaminants may have relatively less time for natural attenuation along the short flow paths, generally occur near streams and rivers where ground water discharges to the surface. Finally, the ground-water-flow models were used to simulate ground-water/surface-water interaction in the five tributary basins. Results of simulations show that some lakes and reservoirs leak surface water into the ground-water-flow system on their downgradient side, where the surface-water outflow has been restricted by a dam or a naturally constricted outlet. These locations are noteworthy because contaminated surface waters could potentially enter the ground-water-flow system at these locations.

Minnesota, Wisconsin↗