USGS ScienceSearch

FIND YOUR NEXT DISCOVERY

Results for “Completion Report”

Original records, connected by a shared subject.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

313 recordsLinked to original sources

Completion summary for monitor wells NRF-17 and NRF-18 at the Naval Reactors Facility, Idaho National Laboratory, Idaho

The U.S. Geological Survey (USGS)—in cooperation with the U.S. Department of Energy (DOE) for the Naval Reactors Laboratory Field Office that supports operations for the Naval Reactors Facility (NRF) located at the Idaho National Laboratory (INL)—drilled and constructed well NRF-17 (formerly borehole USGS 151) and well NRF-18 (formerly borehole USGS 152) for stratigraphic framework analyses and water-quality monitoring at the Idaho National Laboratory (INL) near the NRF, in southeastern Idaho. Borehole USGS 151 was continuously cored from about 48 to 1,070 feet (ft) below land surface (BLS); rotary drilled from approximately 1,070 to 1,720 ft BLS; and re-drilled to complete construction as a monitor well NRF-17, completed to 461 ft BLS. Borehole USGS 152 was continuously cored from approximately 19 to 1,259 ft BLS; rotary drilled from approximately 1,259 to 1,630 ft BLS; and re-drilled to complete construction as a monitor well NRF-18, completed to 450 ft BLS. Geophysical data were examined with photographed core material to record lithologic descriptions and to suggest zones where groundwater flow was anticipated. Basalt flows varied from highly fractured to dense, with high-to-low vesiculation. Well NRF-17 generally was constructed in mostly dense basalt (greater than 75 percent), and well NRF-18 was constructed in primarily fractured and (or) vesicular basalt. In well NRF-17, the well capacity is directly affected by the limited amount of fractured basalt, which serves as the primary pathway for groundwater. This effect was observed during the pumping test conducted after the well's final construction. Single-well aquifer tests were done at wells NRF-17 and NRF-18 to provide estimates of transmissivity and hydraulic conductivity after final well construction and initial well development. Estimated values of transmissivity and hydraulic conductivity for well NRF-17 were 8.81 feet squared per day (ft 2 /d) and 1.04×10 -2 feet per day (ft/d), respectively. Estimated values of transmissivity and hydraulic conductivity for well NRF-18 were 4.77×10 3 ft 2 /d and 5.61 ft/d, respectively. The NRF-17 pump test resulted in 19.41 ft of measured drawdown at a sustained average pumping rate of 3.3 gallons per minute (gal/min). The NRF-18 pump test resulted in 0.55 ft of measured drawdown at a sustained average pumping rate of 31.0 gal/min. Water-quality samples collected from the two wells were analyzed for cations, anions, metals, nutrients, volatile organic compounds, stable isotopes, and radionuclides. Water samples for select inorganic constituents showed concentrations consistent with signatures from tributary valley groundwater with influences from ephemeral surface-water recharge from the Big Lost River. Water-quality samples analyzed for stable isotopes of oxygen and hydrogen are consistent with signatures from tributary valley groundwater and surface-water recharge inputs to the aquifer. No measured water-quality results were greater than their respective maximum contaminant levels for public drinking-water supplies. Inorganic and nutrient water-quality results for well NRF-17 and well NRF-18 suggest the groundwater in this area is potentially affected by industrial wastewater disposal.

Idaho

Mapping potential sensitivity to hydrogeomorphic change in the UMRS riverscape

In 2020 the U.S. Geological Survey (USGS), as part of the Upper Mississippi River Restoration (UMRR) Program, began a new project to characterize potential hydrogeomorphic change associated with hydrogeomorphic units (HGUs) and their catenae (units linked by their association with sediment sources and flow origins). The goal of the project was to develop a geographic information system (GIS) database of HGUs for the Upper Mississippi River System (UMRS) available to both scientists and river managers working on UMRR studies and HREP planning and design studies. The characterization was based on a hydrogeomorphic change hierarchical classification developed previously for the UMRS. The products were generated with automated techniques in a GIS using systemic datasets. Landforms were mapped from the 2015 UMRS topobathymetric dataset with geomorphon (shape-based) tools tailored for the large riverscape, valley bottom environments in the UMRS. A clustering analysis was applied to the resulting landforms to identify HGUs associated with zones of perennial low flows, bankfull flows, and overbank floodplains. Catenae were assembled based on the proximity of the units to the main channel, tributary mouths, and side channels from previously published aquatic areas (USACE, 2018) coupled with least-cost flowpath linkages between potential sediment origins and planform change units developed by Rogala, Fitzpatrick, and Henderson (2020). These GIS-based analyses were successful at identifying a range of HGUs using an automated technique with available data across the entire riverscape, with emphasis on those that have the potential for hydrogeomorphic change. Most of the resulting features are depositional, as expected in a large river system. However, this is the first attempt of linking tributary inputs, side channel erosion and levee breaches with their depositional counterparts. The approach was successfully piloted in Pools 8 and 10 in the Upper Impounded Reach and Pool 14 in the Lower Impounded Reach, with next steps for application in reaches of the unimpounded section and Illinois River. This report emphasizes results from Pool 10, which was the focus of most of our attention during the pilot phase.

Illinois, Indiana, Iowa, Minnesota, Missouri, Sout

The National Map Corps—Federal Emergency Management Agency and Oak Ridge National Laboratory pilot project report

This report provides an overview of the U.S. Geological Survey National Map Corps —Federal Emergency Management Agency and Oak Ridge National Laboratory pilot project in St. James Parish, Louisiana, that began in February 2024 and ended at the end of March 2024. The project used the power of The National Map Corps’ volunteer community to improve building classifications in the original Federal Emergency Management Agency’s U.S.A. Structures dataset. The report highlights the project’s completion and details the work and results achieved through a collaborative effort to enhance geospatial data quality and utility.

Open-File Report

Bathymetric and acoustic-backscatter mapping of Lake Sammamish, Washington, during USGS field activity 2021-656-FA

In 2021, scientists from the U.S. Geological Survey (USGS) acquired bathymetric and acoustic-backscatter data within Lake Sammamish, Washington. Mapping was completed to find evidence of past earthquakes such as underwater landslides and is part of a larger USGS project to understand the overall geologic hazards history of the Cascadia Margin region. The survey was conducted using the USGS research vessel Parke Snavely outfitted with an interferometric sidescan-sonar system for swath mapping. Three estimates of bathymetric uncertainty were calculated from the post-processed bathymetric data. This report provides a summary of the mapping mission.

Washington

Bathymetric maps, surface areas, and storage capacities of Council Grove Lake and Marion Reservoir, Kansas, and Pine Creek Lake, Oklahoma, 2024

The U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, completed high-resolution multibeam bathymetric surveys to compute new elevation-area-capacity tables for Council Grove Lake and Marion Reservoir, Kansas, and Pine Creek Lake, Oklahoma. Elevation-area-capacity tables identify the relation between the water-surface elevation, surface area, and storage capacity of the lake. The surface areas and storage capacities of each lake were computed from bathymetric surfaces combining multibeam echo sounder data collected in 2024 and light detection and ranging point-cloud data collected in 2016 and 2018.

Kansas, Oklahoma

System characterization report on the Environmental Mapping and Analysis Program (EnMAP)

This report addresses system characterization of the Environmental Mapping and Analysis Program hyperspectral sensor by the DLR (German Aerospace Center, ground segment project management), GFZ (Deutsches Geoforschungszentrum, science lead) and is part of a series of system characterization reports produced and delivered by the U.S. Geological Survey Earth Resources Observation and Science Cal/Val Center of Excellence. These reports present and detail the methodology and procedures for characterization; present technical and operational information about the EnMAP hyperspectral sensor; and provide a summary of test measurements, data retention practices, data analysis results, and conclusions. The Earth Resources Observation and Science Cal/Val Center of Excellence system characterization team completed data analyses to characterize the geometric (interior and exterior), and radiometric performances of the EnMAP hyperspectral sensor. Results of these analyses indicate that the Environmental Mapping and Analysis Program has a band-to-band geometric performance in the range of −0.135 to 0.15 pixel, geometric performance relative to the Operational Land Imager in the range of −27.716 meters (−0.92 pixel) to 32.892 meters (1.09 pixels) offset in comparison to Landsat 8 Operational Land Imager, offset of a radiometric comparison in the range of −0.012 to 0.020, slope of a radiometric comparison in the range of 0.947 to 1.031.

Open-File Report

Treatability study to evaluate bioremediation of trichloroethene at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, 2020–22

Executive Summary Chlorinated solvents, including trichloroethene (TCE) and other chlorinated volatile organic compounds (cVOCs), are widespread contaminants that can be treated by bioremediation approaches that enhance anaerobic reductive dechlorination. Reductive dechlorination can be enhanced either through the addition of an electron donor (biostimulation) or the addition of a known dechlorinating culture (bioaugmentation) along with an electron donor. Although bioremediation has been applied at many TCE-contaminated groundwater sites, application in source zones at sites where residual dense nonaqueous phase liquid (DNAPL) is present is more limited. In this study, laboratory and field treatability tests were completed to evaluate the potential application of anaerobic bioremediation for a shallow groundwater plume containing TCE in a perched alluvial aquifer at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, which was on the National Priorities List as the New Brighton/Arden Hills Superfund site until 2019. In addition to the presence of residual DNAPL at the site, temporal variability in groundwater flow directions and input of oxygenated recharge were possible complicating factors for the application of enhanced anaerobic biodegradation in the shallow plume. The Site K plume extends beneath the footprint of Building 103, which was demolished in 2006, and soil excavations to a maximum depth of 6 feet (ft) below ground surface in 2014 were known to leave some deeper contaminated soil in place in the TCE source area. Groundwater treatment at the site, formalized as part of the 1997 Record of Decision, has been in operation since 1986 and consists of an extraction trench at the downgradient edge of the plume to collect groundwater, which is then pumped to an on-site air stripper. Groundwater concentrations in the plume have been relatively stable since treatment began, indicating a continued source of TCE in the aquifer. The desire for a destructive remedy that would enhance the removal of cVOCs in the aquifer at Site K and shorten the remediation timeframe led the U.S. Army to request that the U.S. Geological Survey conduct a groundwater treatability study to assess bioremediation. This report describes the U.S. Geological Survey bioremediation treatability study conducted during 2020–22, including pre-design site characterization to assist in formulating the bioremediation approach, laboratory experiments to support the design of the field pilot test, and implementation and 1-year performance monitoring results for the pilot test. Pre-design site characterization included the collection of soil cores for cVOC analysis and lithologic descriptions and the re-installment of three wells to obtain hydrologic measurements and initial groundwater chemistry. Relatively flat head gradients were measured at the site, and substantial decreases in water-level elevations occurred from spring to summer (May–July 2021). Continuous water-level monitoring indicated a rapid response to precipitation. Groundwater flow velocities were consistently less than 0.5 foot per day, and the pilot bioremediation test was therefore designed with short lateral distances (about 5 ft) between injection and individual monitoring points. Soil analyses confirmed that high volatile organic compound contamination was left in place in the source area. The highest concentrations were near or in clay at the base of the perched aquifer. Concentrations of cVOCs measured in the replaced wells were consistent with historical data and had a maximum TCE concentration of 57,700 micrograms per liter (μg/L), indicative of nearby residual DNAPL based on the general rule of observed concentrations exceeding 1 percent of solubility. The primary TCE daughter product detected was 1,2-cis-dichloroethene (cisDCE), which indicated limited reductive dechlorination in the plume. Groundwater in both the source and downgradient areas was relatively reducing during the pre-design characterization, particularly in the source area where methane concentrations greater than 400 μg/L were measured. Initial laboratory tests conducted using native aquifer microorganisms from the three replacement wells showed that anaerobic TCE biodegradation rates were low when biostimulated with the addition of sodium lactate as an electron donor, also known as a carbon donor, and resulted in the production of only cisDCE. Addition of a known dechlorinating culture, WBC-2, however, resulted in rapid biodegradation and production of ethene, verifying complete reductive dechlorination of TCE. Microcosms constructed with aquifer soil collected from the site were used to evaluate other electron donors besides lactate to support reductive dechlorination by WBC-2, including corn syrup as an alternative fast-release compound and whey, soy-based vegetable oil, and 3-D Microemulsion (Regenesis, San Clemente, California) as slow-release compounds. First-order rate constants for total organic chlorine removal in these WBC-2 amended microcosms were greatest with either lactate or vegetable oil as the donor, ranging between 0.061 and 0.047 per day or corresponding half-lives of 11–15 days. Testing of commercial products in other WBC-2-bioaugmented microcosms led to selection for the field pilot test of an emulsified vegetable oil product that also contained some sodium lactate as a fast-release donor. Delaying the addition of WBC-2 relative to the donor in the microcosms resulted in the most rapid overall biodegradation rates. The selected design for the pilot test utilized three separate test plots, each about 30-ft wide and 60-ft long: plots GS1 and GS2 in the source area of the plume and plot GS3 in the downgradient area of the plume near the excavation trench. Each test plot had one injection well, one monitoring well upgradient from the injection point, and 12 surrounding monitoring wells in a grid to capture variable groundwater flow directions. Donor injections, which included a bromide tracer, were completed in October 2021, immediately following baseline sampling, and the WBC-2 culture was injected about 40 days later, between November 30 and December 2, 2021. Performance monitoring conducted until December 2022 included hydrologic measurements and analyses of cVOCs, redox-sensitive constituents, dissolved organic carbon, bromide, volatile fatty acids, compound-specific carbon isotopes, and microbial communities. The biogeochemical data collected during the pilot tests in the three treatment plots showed that enhanced, complete reductive dechlorination of cVOCs in the groundwater was achieved in the GS1 and GS3 plots. In contrast, evidence of distribution of the injected amendments and subsequent biodegradation was limited in GS2, which was in an area of more heterogeneous soil lithology and low water table elevations. The molar composition of volatile organic compounds in the GS1 and GS3 plots was dominated by ethene in wells that were reached by the injected amendments by the end of the monitoring period. In the GS1 and GS3 plots, similar patterns were observed of cVOC concentrations decreasing to near detection levels, or below, at some wells sampled in July and October 2022, whereas ethene became dominant and indicated sustained complete reductive dechlorination. Baseline cVOC concentrations were more than a factor of 10 higher in the groundwater in the GS1 plot than in GS3, but no apparent inhibition of complete dechlorination occurred. As expected from the initial pre-design site data and the laboratory experiments, enhanced dissolution of residual DNAPL coupled to biodegradation was evident in the GS1 plot, where a marked increase in dichloroethene (DCE) above the initial baseline and upgradient TCE and DCE concentrations occurred. DCE concentrations subsequently declined where DNAPL dissolution was evident, concurrent with production of vinyl chloride and then predominantly ethene. Thus, overall biodegradation rates outpaced the DNAPL dissolution and desorption and DCE production in the source area. This success in complete degradation to predominantly ethene was achieved even in areas where the DCE concentrations reached a maximum of about 30,000 μg/L. Compound specific isotope analysis of carbon in TCE, cisDCE, trans-1,2-dichloroethene, and vinyl chloride was conducted to provide another line of evidence of the occurrence and extent of anaerobic biodegradation. Along a flow path in each plot that was affected by the injected amendments, carbon isotopes in the TCE and daughter cVOCs in the groundwater became isotopically heavier, indicating biodegradation. Enhanced biodegradation rates calculated from the field tests in GS1 and GS3 showed half-lives of 36.9–75.3 days for DCE degradation and 9.48–38.5 days for ethene production. Notably, these ethene production rates calculated from the field tests are consistent with the results of WBC-2-bioaugmented microcosms amended with either lactate or vegetable oil, which had half-lives for total organic chlorine removal that ranged from 11 to 15 days. These rates indicated rapid enhanced biodegradation, which is promising for application of a full-scale bioremediation remedy. Ultimately, however, the mass of residual or sorbed TCE in the aquifer that remains accessible for dissolution and biodegradation would likely control the time required for a full-scale bioremediation effort to achieve performance goals for TCE and cisDCE specified in the Record of Decision for Site K. The field pilot tests showed that the relatively low hydraulic head gradients and temporal changes in groundwater flow directions in the shallow aquifer would add complexity to a full-scale bioremediation effort. The radius of influence (ROI) at GS1 and GS3 (16.3 ft and 12.7 ft, respectively) were close to the design ROI of 15 ft. The estimated ROI at GS2 was about four times the design ROI, but may be less reliable at this location owing to groundwater flow direction. In addition, the low temperatures following WBC-2 injection in late November to early December 2021, in combination with the low hydraulic head gradients, were probably major factors in the delay observed before the onset of enhanced biodegradation following injection of the culture. Additional test injections could be beneficial to optimize the timing of donor and culture injections with the variable temperatures and hydraulic head in the shallow aquifer.

Minnesota

Satellite tracking of Galapagos Petrel Pterodroma phaeopygia reveals distribution and movements during chick rearing

We tracked 19 adult Galapagos Petrels Pterodroma phaeopygia during the chick-rearing seasons in 2009 and 2010 (Santa Cruz Island [ n = 16] and Floreana Island [ n = 3]) in the Galápagos Islands, Ecuador. Eight petrels performed 27 complete foraging trips lasting 0.6 to 18.8 days. Short trips (3.2 ± 2.1 days; 785 km; max displacement 671 km) and long trips (10.8 ± 3.9 days; 2,856 km; max displacement 1,034 km) resulted in concentrated use of waters off southern and western Isabela Island and within the Galápagos Marine Reserve (GMR). Less concentrated time extended farther southwest and eastward, in that case toward mainland Ecuador. Total distance covered among all completed trips, independent of duration, was strongly correlated with trip duration ( R ² = 0.92), indicating a strategy favoring active searching and foraging over commuting. Petrels ranged across Ecuador's exclusive economic zone (EEZ), as well as other countries' (Colombia, Costa Rica, Perú), and waters beyond; they spent 46%, 27%, and 34% of their time in the GMR during short, long, and apparent (incomplete) trips, respectively. However, overlap with EEZs or marine protected areas (MPAs) does not necessarily confer protection, because commercial tuna fishing, including legal fishing historically permitted inside the GMR, occurs within these waters. Including all complete and incomplete trips, petrels spent 37% of their time in high-seas waters without formal protection, outside both MPAs and EEZs. While some hot spots overlapped Galápagos MPAs, the far-ranging nature of chick-provisioning petrels underscores the importance for this species of also having coordinated, multinational protection of the high seas.

Floreana Island, Galápagos Islands, Santa Cruz Isl

Bedrock geologic map of the Bellows Falls 7.5- x 15-minute quadrangle, Windham and Windsor Counties, Vermont, and Sullivan and Cheshire Counties, New Hampshire

Introduction The bedrock geology of the Bellows Falls 7.5- x 15-minute quadrangle, Vermont and New Hampshire, consists of polydeformed Ordovician to Devonian metasedimentary, metavolcanic, and metaplutonic rocks of the Connecticut Valley trough, Bronson Hill anticlinorium (or Bronson Hill terrane), and the Central Maine terrane. Previous work in this area includes a 1:62,500-scale published map and text (1946), State geologic maps of New Hampshire (1997) and Vermont (2011), and various maps and reports presented largely as parts of field trip guidebooks. A provisional open-file map of the geology of the Vermont part of the Bellows Falls 7.5- x 15-minute quadrangle, completed in 1997, is incorporated and revised on this map based on additional fieldwork. This study recognizes three major structural levels from west to east and from lowest to highest: (1) autochthonous rocks of the Connecticut Valley trough; (2) allochthonous rocks of the New Hampshire sequence and Bronson Hill arc in the Monroe thrust sheet (or nappe), including the Skitchewaug nappe; and (3) allochthonous rocks of the Fall Mountain thrust sheet or nappe.

New Hampshire, Vermont

Uppermost Oligocene and Miocene diatom biostratigraphy of Ocean Drilling Program Sites 682 and 688 from the Peru Margin

The diatom biochronology of ODP (Ocean Drilling Program) Holes 682A and 688E provides a detailed framework for refiningMiocene diatom zonation in the East Pisco Basin of southern Peru, establishing both a nearly complete offshore reference section and a correlation tool for the fragmentary onshore vertebrate-bearing deposits. This new biostratigraphic record documents a complete succession of low latitude and/or northeastern Pacific Miocene diatom zones, with two notable exceptions: a dissolution and/or hiatus interval (*16.5–14 Ma) during the Middle Miocene Climatic Optimum and a likely earliest Miocene hiatus (*23.4–21.8 Ma). Although eastern equatorial Pacific diatom zones characterize the Upper Oligocene and Lower Miocene strata, an increased abundance of cool-water diatoms that lived during the Middle and Late Miocene allows better application of northeast Pacific diatom zones, except during the Messinian (7–6 Ma) when warm-water diatoms predominate. The effects of eustatic sea level and tectonics on depositional sequences in the EPB and in offshore cores off central Peru are discussed.

Stratigraphy

Hydrogeology of unconsolidated and bedrock aquifers along the Salmon River, including Malone, Franklin County, New York

The U.S. Geological Survey, in cooperation with the New York State Department of Environmental Conservation, investigated the hydrogeology of the unconsolidated and bedrock aquifers along the Salmon River corridor in northern Franklin County, New York. The study area covers roughly 147 square miles and includes the village of Malone and parts of the Towns of Malone, Bellmont, Burke, Constable, Westville, Bangor, Duane, and Franklin, New York. Groundwater is the primary source for water supply within the study area. Eighty-three percent of all residents use public water supplied from two production wells that draw water from a thick, highly productive sand-and-gravel aquifer likely receiving induced infiltration from the Salmon River. Twenty-four percent of the 187 verified domestic wells in the study area outside of the production well service area boundary are screened in typically discontinuous deposits of stratified sand and sand and gravel. Seventy-six percent of the wells are completed in bedrock aquifers including the Potsdam Sandstone, metamorphic rocks, Theresa Formation, and unknown bedrock. Characterizing and understanding potential groundwater resources is critical for protecting the quality of the groundwater. The information in this report may be used to guide delineation of groundwater contributing areas, assess potential threats to aquifers from both point and nonpoint sources, respond to contamination from spills or leaks from underground storage facilities or other sources, and to support assessments for future development of municipal water supplies.

New York

Geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers within Hays County, Texas

During 2023–24, the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, revised a previous publication of the geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers that was completed during 2018 within Hays County, Texas. The purpose of this report is to present the updated geologic framework and hydrostratigraphy of the rocks containing the Edwards and Trinity aquifers in Hays County from field observations of the surficial expressions of the rocks. The report includes a detailed 1:24,000-scale hydrostratigraphic map with names and descriptions of the geologic framework and hydrostratigraphic units (HSUs) in the study area. The study includes updates to the interpretation of the Kainer Formation of the Edwards Group with the addition of a burrowed unit between the basal nodular and dolomitic members. Hydrostratigraphy was also updated with the addition of the Seco Pass HSU for the burrowed member of the Kainer Formation. The study also includes updates to the interpretation of the hydrostratigraphy of the Trinity aquifer with the addition of the cavernous HSU at the top of the upper zone of the Trinity aquifer and the Herff Falls HSU between the Bulverde and Rust HSUs of the middle zone of the Trinity aquifer. This updated report provides additional information about a complex aquifer system. The complexity in the aquifer system results from a combination of the original depositional history, bioturbation, development of primary and secondary porosity, postdepositional diagenesis, fracturing, and faulting.

Texas

Rewilding the upper Klamath River Basin: Rapid recolonization of Chinook salmon following the world’s largest dam removal

Habitat fragmentation is a global driver of decline in biodiversity, yet evaluations of ecological response following re-connection remain rare. In 2024, four hydroelectric dams on the Klamath River were removed, reconnecting over 640 km of anadromous habitat and marking the largest dam removal project completed to date. We used a stationary high-resolution multi-beam imaging SONAR to quantify adult Chinook salmon ( Oncorhynchus tshawytscha ) passage into newly reopened reaches during the first two migratory seasons following dam removal. An estimated 7,742 (95% CI: 7,702–7,778) Chinook salmon migrated upstream in 2024 and 13,310 (95% CI: 12,876–13,733) in 2025, representing 18–19% of fish returning to the Klamath River Basin. Within this period, Chinook salmon recolonized 88% of their documented historical distribution, expanding into 345 km of reconnected habitats and reaching elevations of up to 1,250 m. Recolonization required fish to swim through dam removal sites, complex hydraulic corridors and engineered fishways, demonstrating the propensity for rapid recolonization at basin scale despite these challenges. These findings provide the first quantitative assessment of salmon response to the world’s largest dam removal and demonstrate how reconnection can catalyze large-scale recolonization in historically fragmented river networks.

California, Oregon

Comparisons of shoreline positions from satellite-derived and traditional field- and remote-sensing techniques

Satellite-derived shorelines (SDS) have the potential to help researchers answer critical coastal science questions and support work to predict coastal change by filling in the spatial and temporal gaps present in current field-based and remote-sensing data collection methods. The U.S. Geological Survey conducted comparison analyses of traditionally sourced shorelines and SDS in diverse coastal landscapes to determine how SDS could be used in ongoing and future work across varied coastal environments and provided some initial findings that could be used for implementation. Using CoastSeg, a browser-based program for SDS detection and mapping, SDS for the period 1984–2023 for multiple locations across the United States were compared to shoreline positions from traditionally sourced shoreline data. In this report, the authors present these comparisons alongside lessons learned and challenges encountered when building SDS workflows in different coastal locations. Results show that individual SDS have larger uncertainty and yet produced similar linear trends to sparser, traditionally sourced shoreline data; because SDS methods provide orders of magnitude more data than traditional shoreline-detection methods, they can be used to evaluate shoreline behaviors. Refining average scalar slopes used in tidal corrections did not result in substantial decreases in uncertainty. Using lessons from this work to outline needs for regional implementation, initial setup time would be considerable, being on the order of weeks. However, once complete, shoreline detections and analyses are fast (on the order of minutes to hours) and achievable using a desktop computer.

Alaska, Florida, Massachusetts, Washington

Selected water-quality data from the Cedar River and Cedar Rapids well fields, Cedar Rapids, Iowa, 2017–22

The Cedar River alluvial aquifer is the source of drinking water in Cedar Rapids, Iowa. Production wells are completed in the alluvial aquifer approximately 40 to 80 feet below land surface. The City of Cedar Rapids and the U.S. Geological Survey have studied the groundwater-flow system and water quality of the aquifer in the vicinity of Cedar Rapids since 1992. Results of these studies documented hydrologic conditions, water quality, and geochemistry of the alluvial aquifer and interactions with the Cedar River. Water-quality samples were collected for studies involving well field monitoring, trends, source-water protection, groundwater geochemistry, surface-water–groundwater interaction, and pesticides in groundwater and surface water. Water quality was analyzed for dissolved major ions (boron, bromide, calcium, chloride, fluoride, iron, magnesium, manganese, potassium, silica, sodium, sulfate, and total dissolved solids), dissolved nutrients (ammonia as nitrogen, ammonia plus organic nitrogen as nitrogen, nitrite plus nitrate as nitrogen, nitrite as nitrogen, orthophosphate as phosphorus, and phosphorus), dissolved organic carbon, and selected pesticides. Physical characteristics (alkalinity, dissolved oxygen, pH, specific conductance, and water temperature) were measured on site and recorded for each water sample collected. This report presents the results of routine water-quality data-collection activities from October 2017 through September 2022. Methods of data collection, quality assurance, water-quality analyses, and statistical procedures are presented. Data include the results of water-quality analyses from quarterly sampling from monitoring wells, production wells, two water treatment plants, and the Cedar River at Blairs Ferry Road at Palo, Iowa, streamgage (U.S. Geological Survey station number 05464420), as well as monthly nutrient sampling from the Cedar River and Morgan Creek near Covington, Iowa, streamgage (U.S. Geological Survey station number 05464475).

Iowa

Altitude of the potentiometric surface and depth to water in the Mississippi River Valley alluvial aquifer, spring 2022

Potentiometric-surface and depth-to-water maps for spring 2022 were created for the Mississippi River Valley alluvial aquifer (MRVA) using groundwater-altitude data from 1,136 wells completed in the MRVA and from the altitude of the top of the water surface in area rivers from 160 streamgages. The potentiometric-surface and depth-to-water maps for 2022 were created to support investigations to characterize the MRVA as part of the U.S. Geological Survey Water Availability and Use Science Program. Sufficient data were available to map the potentiometric surface and depth to water of the MRVA for spring 2022 for about 83 percent of the aquifer area. The potentiometric contours ranged from 0 to 340 feet (ft) above the North American Vertical Datum of 1988. The regional direction of groundwater gradient was generally to the south-southwest, except in areas of groundwater-altitude depressions, where the groundwater gradient was into the depression, and near rivers, where the groundwater gradient can be from aquifer to the river or from the river into the aquifer. There are large depressions in the potentiometric-surface map in the lower one-half of the Cache region and in much of the Grand Prairie and Delta regions. Depth to water in the MRVA, spring 2022, by well ranged from 5.00 ft above land surface to 145.66 ft below land surface.

Mississippi River Valley alluvial aquifer

Stepovers and beyond: Structural control of The Geysers geothermal system and the broader Clear Lake region

Fault geometry exerts a first-order control on geothermal systems by governing stress localization, fracture development, and permeability, yet in complex fault networks or broader shear zones, the relative influence of individual geometric features is often difficult to resolve. In the northern California Coast Ranges, The Geysers geothermal field is commonly interpreted to occur within a releasing stepover, although no single, clearly defined stepover is identified in published studies. To investigate the structural controls on The Geysers and the broader Clear Lake region, a two-dimensional elastic boundary element model is developed to evaluate spatial patterns of dilational strain associated with progressively more complete fault geometries. Model results show that dilation in the region is not controlled by a single structure but instead reflects the combined effects of multiple interacting fault elements. Three primary controls are identified: (1) opposing bends in the regional strike-slip fault system, including a releasing bend along the Maacama fault; (2) the southern fault tip of the Collayomi fault, which generates a prominent dilational lobe beneath the southern Geysers; and (3) a releasing stepover between the Collayomi fault and the Geyser Peak–Mercuryville–Big Sulphur Creek fault system, inferred to collectively behave as a right-lateral shear zone bounding the western margin of The Geysers. Predicted dilational strain magnitudes are sufficient to localize permeability between faults. These results highlight that incorporating complete fault networks and bedrock geological mapping can enhance geothermal assessments and provide a transferable framework for evaluating structurally controlled permeability in tectonically active regions.

California

Geologic framework, hydrostratigraphy, and ichnology of the Blanco, Payton, and Rough Hollow 7.5-minute quadrangles, Blanco, Comal, Hays, and Kendall Counties, Texas

During 2023, the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, revised an initial characterization completed during 2015–16 of the geologic framework, hydrostratigraphy, and ichnology of the Edwards and Trinity aquifers in the Blanco, Payton, and Rough Hollow 7.5-minute quadrangles in Blanco, Comal, Hays, and Kendall Counties, Texas. The purpose of this report is to present the updated geologic framework, hydrostratigraphy, and ichnology of the Trinity and Edwards Groups in those quadrangles. Rocks exposed in the study area are of the Lower Cretaceous Trinity Group and lower part of the Fort Terrett Formation of the Lower Cretaceous Edwards Group. The faulting and fracturing in the study area are part of the Balcones Fault Zone, an extensional system of faults active during the Paleocene to middle Eocene that generally trends southwest to northeast in south-central Texas. Hydrostratigraphically, the rocks exposed in the study area contain a section of the Edwards (Balcones Fault Zone) aquifer, upper zone of the Trinity aquifer, and middle zone of the Trinity aquifer. In the study area, the only hydrostratigraphic units of the Edwards (Balcones Fault Zone) aquifer remaining are (from top to bottom) VII and VIII, which cap several hills. The mapped hydrostratigraphic units of the upper zone of the Trinity aquifer are (from top to bottom) the cavernous, Camp Bullis, upper evaporite, fossiliferous, and lower evaporite. The mapped hydrostratigraphic units of the middle zone of the Trinity aquifer are (from top to bottom) the Bulverde, Little Blanco, Twin Sisters, Doeppenschmidt, Herff Falls (where present), Rust, Honey Creek, Hensell, and Cow Creek hydrostratigraphic units.

Texas