USGS Science⌕ Search

SEARCH · USGS Science

Results for “Atmospheric Measurement Techniques Discussions”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

11 recordsLinked to original sources
USGS2011

Early in-flight detection of SO 2 via Differential Optical Absorption Spectroscopy: A feasible aviation safety measure to prevent potential encounters with volcanic plumes

Volcanic ash constitutes a risk to aviation, mainly due to its ability to cause jet engines to fail. Other risks include the possibility of abrasion of windshields and potentially serious damage to avionic systems. These hazards have been widely recognized 5 since the early 1980s, when volcanic ash provoked several incidents of engine failure in commercial aircraft. In addition to volcanic ash, volcanic gases also pose a threat. Prolonged and/or cumulative exposure to sulphur dioxide (SO 2 ) or sulphuric acid (H 2 SO 4 ) aerosols potentially affects e.g. windows, air frame and may cause permanent damage to engines. SO 2 receives most attention among the gas species commonly found in 10 volcanic plumes because its presence above the lower troposphere is a clear proxy for a volcanic cloud and indicates that fine ash could also be present. Up to now, remote sensing of SO 2 via Differential Optical Absorption Spectroscopy (DOAS) in the ultraviolet spectral region has been used to measure volcanic clouds from ground based, airborne and satellite platforms. Attention has been given to vol- 15 canic emission strength, chemistry inside volcanic clouds and measurement procedures were adapted accordingly. Here we present a set of experimental and model results, highlighting the feasibility of DOAS to be used as an airborne early detection system of SO 2 in two spatial dimensions. In order to prove our new concept, simultaneous airborne and ground-based measurements of the plume of Popocatepetl volcano, Mexico, were conducted in April 2010. The plume extended at an altitude around 5250 m above sea level and was approached and traversed at the same altitude with several forward looking DOAS systems aboard an airplane. These DOAS systems measured SO 2 in the flight direction and at ±40 mrad (2.3◦) angles relative to it in both, horizontal and vertical directions. The approaches started at up to 25 km distance to 25 the plume and SO 2 was measured at all times well above the detection limit. In combination with radiative transfer studies, this study indicates that an extended volcanic cloud with a concentration of 1012 molecules cm−3 at typical flight levels of 10 km can be detected unambiguously at distances of up to 80 km away. This range provides enough time (approx. 5 min) for pilots to take action to avoid entering a volcanic cloud in the flight path, suggesting that this technique can be used as an effective aid to prevent dangerous aircraft encounters with potentially ash rich volcanic clouds.

Popocatepetl volcano↗
USGS2007

Water Budgets: Foundations for Effective Water-Resources and Environmental Management

INTRODUCTION Water budgets provide a means for evaluating availability and sustainability of a water supply. A water budget simply states that the rate of change in water stored in an area, such as a watershed, is balanced by the rate at which water flows into and out of the area. An understanding of water budgets and underlying hydrologic processes provides a foundation for effective water-resource and environmental planning and management. Observed changes in water budgets of an area over time can be used to assess the effects of climate variability and human activities on water resources. Comparison of water budgets from different areas allows the effects of factors such as geology, soils, vegetation, and land use on the hydrologic cycle to be quantified. Human activities affect the natural hydrologic cycle in many ways. Modifications of the land to accommodate agriculture, such as installation of drainage and irrigation systems, alter infiltration, runoff, evaporation, and plant transpiration rates. Buildings, roads, and parking lots in urban areas tend to increase runoff and decrease infiltration. Dams reduce flooding in many areas. Water budgets provide a basis for assessing how a natural or human-induced change in one part of the hydrologic cycle may affect other aspects of the cycle. This report provides an overview and qualitative description of water budgets as foundations for effective water-resources and environmental management of freshwater hydrologic systems. Perhaps of most interest to the hydrologic community, the concepts presented are also relevant to the fields of agriculture, atmospheric studies, meteorology, climatology, ecology, limnology, mining, water supply, flood control, reservoir management, wetland studies, pollution control, and other areas of science, society, and industry. The first part of the report describes water storage and movement in the atmosphere, on land surface, and in the subsurface, as well as water exchange among these compartments. Our ability to measure these phenomena and inherent uncertainties in measurement techniques also are discussed. The latter part of the report presents a number of case studies that illustrate how water-budget studies are conducted, documents how human activities affect water budgets, and describes how water budgets are used to address water and environmental issues.

Circular↗
USGS2025

Ultraviolet and visible remote sensing of volcanic gases

As magma rises in volcanic systems, volatile species exsolve from the silicate melt and are emitted as gases into the atmosphere. Measuring the magnitude and composition of gas emissions from volcanoes provides insights into processes occurring deep within the Earth and helps constrain the impact of volcanic degassing on atmospheric chemistry. Optical remote sensing techniques allow volcanic gas emissions to be characterized without the need to access hazardous areas near active volcanic vents. This paper reviews the state of the art in ultraviolet and visible volcanic gas remote sensing from the ground, air, and space. Special attention is given to discussing the physics of atmospheric radiative transfer on which these techniques are based. The functionality and limitations of different remote sensing instruments are examined, making clear that the ideal choice of instrumentation will depend on the volcanic system to which it is applied and the sought measurement parameters. Common algorithms for determining trace gas column densities, gas burdens, and volcanic emission rates from measurements of spectral radiance are outlined and compared, showing how some algorithms attempt to model the physics of the measurement while others maximize sensitivity. Several examples demonstrate how remote sensing measurements continue to advance our understanding of volcanic systems and their impact on the atmosphere. Finally, a few promising directions of inquiry are suggested that could lead to improvements in remote sensing instrumentation and analysis techniques. By combining spectroscopic and imaging techniques, improving our understanding of atmospheric radiative transfer, expanding the suite of target gases, and increasing the coverage and frequency of observations, we stand to significantly improve our ability to detect and quantify volcanic gas emissions and gain new insights into important Earth-system processes.

Journal of Volcanology and Geothermal Research↗
USGS2025

Insights and strategic opportunities from the USGS 2024 Per- and Polyfluoroalkyl Substances (PFAS) Interagency Workshop

Introduction In 2021, the U.S. Geological Survey (USGS) published Circular 1490 titled, “Integrated Science for the Study of Perfluoroalkyl and Polyfluoroalkyl Substances (PFAS) in the Environment: A Strategic Science Vision for the U.S. Geological Survey” (Tokranov and others, 2021). Circular 1490 was created to be a resource for USGS scientists prioritizing and planning research related to per- and polyfluoroalkyl substances (PFAS) and to be a guide for developing partnerships with other scientists, State and Federal agencies, and stakeholders engaged in PFAS research and management and mitigation of the environmental and human-health effects of PFAS. This USGS PFAS Strategic Science Vision document was intended to be the foundation for a “living strategic vision,” periodically providing updates on the state of USGS PFAS research, emerging PFAS data gaps and needs, and progress on interagency and stakeholder PFAS partnerships and priorities. To meet this objective, the USGS planned to host an Interagency and Stakeholder PFAS Workshop every 2–3 years. During September 10–12, 2024, the USGS hosted the first Interagency and Stakeholder PFAS Workshop in Reston, Virginia. The Workshop brought together experts from other Federal agencies (U.S. Environmental Protection Agency, National Institute of Environmental Health Sciences, Food and Drug Administration, Department of Defense [Air Force, Army]), State agencies (Washington Fish and Wildlife, Virginia Department of Transportation), and academia (Harvard University, University of Maryland) to address key challenges relating to the measurement and modeling of PFAS and the implications for environmental health. Participants engaged in in-depth discussions centered around six pivotal topics related to PFAS: (1) sampling protocols, methods and interpretation; (2) environmental sources, source apportionment, and occurrence; (3) environmental fate and transport; (4) human and wildlife exposure routes and risk; (5) bioconcentration, bioaccumulation, and biomagnification; and (6) ecotoxicology and effects. Each topic had three breakout sessions. A recurrent theme of workshop discussions was how data on a nationwide scale for PFAS occurrence in various environmental matrices, including air, water, food crops, biota, soil, and streambed sediment could help to advance scientific understanding. Participants noted significant geospatial data gaps, particularly in the midwestern and southern United States and the Pacific Northwest. PFAS data collection tends to be more robust along the eastern seaboard and in California. Participants stressed how enhancing the integration of large and small datasets across various agencies could help to support national scale understanding of PFAS. To address these gaps, attendees suggested leveraging datasets from Federal entities like the USGS and the U.S. Department of Defense, State agencies, and municipal utility services to develop predictive contaminant detection and transport models. Improved coordination between water quality programs and USGS research could help to facilitate access to valuable data, leading to comprehensive databases that inform PFAS point (wastewater treatment plants and landfills) and nonpoint (runoff from land, atmospheric deposition, food packaging) sources, environmental transport mechanisms, environmental detection and concentrations, potential exposure routes, and health effects on different biota, including humans. A specific request was made to develop a map demarking the depth of modern (1953 or later) groundwater, which is susceptible to surface-derived anthropogenic (that is, human-made) contamination, based on tritium-age dating. Emphasis was placed on incorporation of hydrology, groundwater flow paths, groundwater–surface water interactions, and landscape factors in predictive statistical models as a step to improve contaminant source identification and tracking. Molecular fingerprinting approaches garnered attention as techniques to link specific PFAS mixtures detected in a sample to environmental sources and levels in biota (Dávila-Santiago and others, 2022). Integrating data from abiotic (that is, water, soil, and air) and biotic (that is, living organisms) systems identified as a research opportunity. For example, understanding the composition of soils and sediments, which include a mixture of mineral, plant, and animal components, could advance understanding of exposure pathways. The discussions highlighted opportunities to explore and understand the potential redistribution and biotic exposures of PFAS from biosolid and wastewater treatment plant effluent land application practices, in addition to atmospheric releases and discharges from landfill and wastewater treatment plants. Participants identified research gaps surrounding how these sources may contribute to contamination and may affect surrounding ecosystems, including a better definition of anthropogenic background concentrations. Moving forward, the collection of co-occurrence data was noted as a means to improve understanding of complex mixtures and to leverage companion modeling efforts focused on areas with high and low contamination levels to identify areas of concern and unaffected resources. Participants emphasized how centralized USGS databases and the establishment of sample-metadata archives can help to ensure that samples are preserved and accessible for future research. In conclusion, the workshop participants identified opportunities to bridge data gaps and improve measurement techniques, modeling frameworks, databases, and communication, to enhance the understanding of PFAS and their effects on environmental and human health. Upon completion of the workshop, participants indicated an interest in developing strategic data collection, modeling, and analytical approaches to address these challenges.

Open-File Report↗
USGS2011

Measurement and modeling of unsaturated hydraulic conductivity

The unsaturated zone plays an extremely important hydrologic role that influences water quality and quantity, ecosystem function and health, the connection between atmospheric and terrestrial processes, nutrient cycling, soil development, and natural hazards such as flooding and landslides. Unsaturated hydraulic conductivity is one of the main properties considered to govern flow; however it is very difficult to measure accurately. Knowledge of the highly nonlinear relationship between unsaturated hydraulic conductivity (K) and volumetric water content () is required for widely-used models of water flow and solute transport processes in the unsaturated zone. Measurement of unsaturated hydraulic conductivity of sediments is costly and time consuming, therefore use of models that estimate this property from more easily measured bulk-physical properties is common. In hydrologic studies, calculations based on property-transfer models informed by hydraulic property databases are often used in lieu of measured data from the site of interest. Reliance on database-informed predicted values with the use of neural networks has become increasingly common. Hydraulic properties predicted using databases may be adequate in some applications, but not others. This chapter will discuss, by way of examples, various techniques used to measure and model hydraulic conductivity as a function of water content, K(). The parameters that describe the K() curve obtained by different methods are used directly in Richards’ equation-based numerical models, which have some degree of sensitivity to those parameters. This chapter will explore the complications of using laboratory measured or estimated properties for field scale investigations to shed light on how adequately the processes are represented. Additionally, some more recent concepts for representing unsaturated-zone flow processes will be discussed.

Book chapter↗
USGS2011

Monitoring of urban subsidence with SAR interferometric point target analysis: A case study in Suzhou, China

Ground subsidence, mainly caused by over exploitation of groundwater and other underground resources, such as oil, gas and coal, occurs in many cities in China. The annual direct loss associated with subsidence across the country is estimated to exceed 100 million US dollar. Interferometric SAR (InSAR) is a powerful tool to map ground deformation at an unprecedented level of spatial detail. It has been widely used to investigate the deformation resulting from earthquakes, volcanoes and subsidence. Repeat-pass InSAR, however, may fail due to impacts of spatial decorrelation, temporal decorrelation and heterogeneous refractivity of atmosphere. In urban areas, a large amount of natural stable radar reflectors exists, such as buildings and engineering structures, at which radar signals can remain coherent during a long time interval. Interferometric point target analysis (IPTA) technique, also known as persistent scatterers (PS) InSAR is based on these reflectors. It overcomes the shortfalls in conventional InSAR. This paper presents a procedure for urban subsidence monitoring with IPTA. Calculation of linear deformation rate and height residual, and the non-linear deformation estimate, respectively, are discussed in detail. Especially, the former is highlighted by a novel and easily implemented 2-dimensional spatial search algorithm. Practically useful solutions that can significantly improve the robustness of IPTA, are recommended. Finally, the proposed procedure is applied to mapping the ground subsidence in Suzhou city, Jiangsu province, China. Thirty-four ERS-1/2 SAR scenes are analyzed, and the deformation information over 38,881 point targets between 1992 and 2000 are generated. The IPTA-derived deformation estimates correspond well with leveling measurements, demonstrating the potential of the proposed subsidence monitoring procedure based on IPTA technique. Two shortcomings of the IPTA-based procedure, e.g., the requirement of large number of SAR images and assumed linear plus non-linear deformation model, are discussed as the topics of further research.

Jaingsu Province↗
USGS2010

Water-budget methods

A water budget is an accounting of water movement into and out of, and storage change within, some control volume. Universal and adaptable are adjectives that reflect key features of water-budget methods for estimating recharge. The universal concept of mass conservation of water implies that water-budget methods are applicable over any space and time scales (Healy et al ., 2007). The water budget of a soil column in a laboratory can be studied at scales of millimeters and seconds. A water-budget equation is also an integral component of atmospheric general circulation models used to predict global climates over periods of decades or more. Water-budget equations can be easily customized by adding or removing terms to accurately portray the peculiarities of any hydrologic system. The equations are generally not bound by assumptions on mechanisms by which water moves into, through, and out of the control volume of interest. So water-budget methods can be used to estimate both diffuse and focused recharge, and recharge estimates are unaffected by phenomena such as preferential flow paths within the unsaturated zone. Water-budget methods represent the largest class of techniques for estimating recharge. Most hydrologic models are derived from a water-budget equation and can therefore be classified as water-budget models. It is not feasible to address all water-budget methods in a single chapter. This chapter is limited to discussion of the “residual” water-budget approach, whereby all variables in a water-budget equation, except for recharge, are independently measured or estimated and recharge is set equal to the residual. This chapter is closely linked with Chapter 3, on modeling methods, because the equations presented here form the basis of many models and because models are often used to estimate individual components in water-budget studies. Water budgets for streams and other surface-water bodies are addressed in Chapter 4. The use of soil-water budgets and lysimeters for determining potential recharge and evapotranspiration from changes in water storage is discussed in Chapter 5. Aquifer water-budget methods based on the measurement of groundwater levels are described in Chapter 6.

Book chapter↗
USGS2002

Rationale and operational plan to upgrade the U.S. gravity database

A concerted effort is underway to prepare a substantially upgraded digital gravity anomaly database for the United States and to make this data set and associated usage tools available on the internet. This joint effort, spearheaded by the geophysics groups at the National Imagery and Mapping Agency (NIMA), University of Texas at El Paso (UTEP), U.S. Geological Survey (USGS), and National Oceanic and Atmospheric Administration (NOAA), is an outgrowth of the new geoscientific community initiative called Geoinformatics (www.geoinformaticsnetwork.org). This dominantly geospatial initiative reflects the realization by Earth scientists that existing information systems and techniques are inadequate to address the many complex scientific and societal issues. Currently, inadequate standardization and chaotic distribution of geoscience data, inadequate accompanying documentation, and the lack of easy-to-use access tools and computer codes for analysis are major obstacles for scientists, government agencies, and educators. An example of the type of activities envisioned, within the context of Geoinformatics, is the construction, maintenance, and growth of a public domain gravity database and development of the software tools needed to access, implement, and expand it. This product is far more than a high quality database; it is a complete data system for a specific type of geophysical measurement that includes, for example, tools to manipulate the data and tutorials to understand and properly utilize the data. On August 9, 2002, twenty-one scientists from the federal, private and academic sectors met at a workshop to discuss the rationale for upgrading both the United States and North American gravity databases (including offshore regions) and, more importantly, to begin developing an operational plan to effectively create a new gravity data system. We encourage anyone interested in contributing data or participating in this effort to contact G.R. Keller or T.G. Hildenbrand. This workshop was the first step in building a web-based data system for sharing quality gravity data and methodology, and it builds on existing collaborative efforts. This compilation effort will result in significant additions to and major refinement of the U.S. database that is currently released publicly by NOAA’s National Geophysical Data Center and will also include an additional objective to substantially upgrade the North American database, released over 15 years ago (Committee for the Gravity Anomaly Map of North America, 1987).

Open-File Report↗
USGS2013

Applying UV cameras for SO 2 detection to distant or optically thick volcanic plumes

Ultraviolet (UV) camera systems represent an exciting new technology for measuring two dimensional sulfur dioxide (SO 2 ) distributions in volcanic plumes. The high frame rate of the cameras allows the retrieval of SO 2 emission rates at time scales of 1 Hz or higher, thus allowing the investigation of high-frequency signals and making integrated and comparative studies with other high-data-rate volcano monitoring techniques possible. One drawback of the technique, however, is the limited spectral information recorded by the imaging systems. Here, a framework for simulating the sensitivity of UV cameras to various SO 2 distributions is introduced. Both the wavelength-dependent transmittance of the optical imaging system and the radiative transfer in the atmosphere are modeled. The framework is then applied to study the behavior of different optical setups and used to simulate the response of these instruments to volcanic plumes containing varying SO 2 and aerosol abundances located at various distances from the sensor. Results show that UV radiative transfer in and around distant and/or optically thick plumes typically leads to a lower sensitivity to SO 2 than expected when assuming a standard Beer–Lambert absorption model. Furthermore, camera response is often non-linear in SO 2 and dependent on distance to the plume and plume aerosol optical thickness and single scatter albedo. The model results are compared with camera measurements made at Kilauea Volcano (Hawaii) and a method for integrating moderate resolution differential optical absorption spectroscopy data with UV imagery to retrieve improved SO 2 column densities is discussed.

Journal of Volcanology and Geothermal Research↗
USGS2004

Estimating hydraulic properties of the Floridan Aquifer System by analysis of earth-tide, ocean-tide, and barometric effects, Collier and Hendry Counties, Florida

Aquifers are subjected to mechanical stresses from natural, non-anthropogenic, processes such as pressure loading or mechanical forcing of the aquifer by ocean tides, earth tides, and pressure fluctuations in the atmosphere. The resulting head fluctuations are evident even in deep confined aquifers. The present study was conducted for the purpose of reviewing the research that has been done on the use of these phenomena for estimating the values of aquifer properties, and determining which of the analytical techniques might be useful for estimating hydraulic properties in the dissolved-carbonate hydrologic environment of southern Florida. Fifteen techniques are discussed in this report, of which four were applied. An analytical solution for head oscillations in a well near enough to the ocean to be influenced by ocean tides was applied to data from monitor zones in a well near Naples, Florida. The solution assumes a completely non-leaky confining unit of infinite extent. Resulting values of transmissivity are in general agreement with the results of aquifer performance tests performed by the South Florida Water Management District. There seems to be an inconsistency between results of the amplitude ratio analysis and independent estimates of loading efficiency. A more general analytical solution that takes leakage through the confining layer into account yielded estimates that were lower than those obtained using the non-leaky method, and closer to the South Florida Water Management District estimates. A numerical model with a cross-sectional grid design was applied to explore additional aspects of the problem. A relation between specific storage and the head oscillation observed in a well provided estimates of specific storage that were considered reasonable. Porosity estimates based on the specific storage estimates were consistent with values obtained from measurements on core samples. Methods are described for determining aquifer diffusivity by comparing the time-varying drawdown in an open well with periodic pressure-head oscillations in the aquifer, but the applicability of such methods might be limited in studies of the Floridan aquifer system.

Florida↗
USGS2019

Demonstrating the value of Earth observations—methods, practical applications, and solutions—group on Earth observations side event proceedings

Executive Summary The U.S. Geological Survey, the National Oceanic and Atmospheric Administration, the European Association for Remote Sensing Companies, and the European Space Agency in coordination with the GEOValue Community hosted a side event to the Group on Earth Observations Plenary on October 23–24, 2017, in Washington, D.C. The workshop, entitled “Demonstrating the Value of Earth Observations: Methods, Practical Applications and Solutions,” brought together more than 60 international experts including economists, scientists, and engineers to consider the state of the science and applications of valuing Earth observations (EO). This 2-day workshop built upon previous activities developed under the GEOValue initiative. This workshop brought together expert analysts from multiple disciplines and backgrounds who are developing methods to identify and measure the value of information generated from the use of satellite and in-situ data. The mix of government agencies, international financial institutions, and independent consultants who participated in the workshop blended to develop a rich mix of views, approaches, and outcomes. During the first part of the workshop, the focus was on the latest science in valuing EO. A number of methodologies were described. Approaches generally assess the societal benefits of specific actions (for example, investments in EO). Some methods focus on broad measures of economic activity (for example, gross domestic product) or methods to assess total economic value such as contingent valuation surveys. Alternatively, use-case approaches (a use case is defined as an evaluation in which one or more decisions, applications, or other uses of data, information, and information products are specifically considered) start with the specific actions and how information is used to support decision making and affect outcomes. The second part of the meeting was focused on the use and development of value chains and decision trees. A value chain can be defined as the set of value-adding activities that one or more organizations perform in creating and distributing goods and services. In terms of EO, the value chain approach can be applied to consider societal benefits of the data and assess the value of data and data features. The EO value chain considers the geospatial data sources and the processing of the data into value added information to be incorporated into decision-support systems, leading to decision makers’ actions. To understand the value of EO, one would also need to recognize the demand side of the equation or how EO benefits users. Extending the value chain concept and incorporating tenets of Bayesian decision making, a decision tree would include one or more use cases. The value provided by the marginal increase in information could flow from one or several parts of the supply side of the value chain. The decision tree is based on the premise that information has no value if it is not used in at least one decision. By connecting the value chain and the decision tree, a framework is created that allows for conceptualizing the value of EO in its many uses. One can then apply economic techniques to monetize the marginal benefit of an outcome with information versus one without. A third part of the meeting applied the value chain and decision-tree frameworks to five specific thematic areas, each with the focus of using information for a decision point: Effect of increasing temperatures on human health; Flooding—Mitigating, managing, and avoiding impacts to safety and property damage; Harmful algal blooms—Effects on human health, recreation, and tourism; Energy and mineral supply—Mitigating, managing, and avoiding impacts of shortfalls on the economy; and Effects of natural hazards on transportation systems—Effects on mobility, safety, and the economy. During the working session, five separate groups worked to define and delineate the value chains and decision trees associated with each topic, discussing the related challenges and data needs. The outcomes were reported back to the full group. Because of the complexity of the topics, most groups first identified a network of value chains and then narrowed the scope to develop a single value chain to address their group’s topic. Although they worked separately and on different topics, the groups came to similar conclusions, concurring that the value chain and decision-tree frameworks are very effective for informing quantitative impact assessments and developing a relatable narrative to assist the public in understanding the link between EO and citizens.

Open-File Report↗