USGS Science⌕ Search

SEARCH · USGS Science

Results for “Acoustics”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 recordsLinked to original sources
USGS1985

Acoustic-televiewer and acoustic-waveform logs used to characterize deeply buried basalt flows, Hanford site, Benton County, Washington

Acoustic-waveform and acoustic-televiewer logs were obtained for a 400-meter interval of deeply buried basalt flows in three boreholes, and over shorter intervals in two additional boreholes located on the U.S. Department of Energy 's Hanford site in Benton County, Washington. Borehole-wall breakouts were observed in the unaltered interiors of a large part of individual basalt flows; however, several of the flows in one of the five boreholes had almost no breakouts. The distribution of breakouts observed on the televiewer logs correlated closely with the incidence of core disking in some intervals, but the correlation was not always perfect, perhaps because of the differences in the specific fracture mechanisms involved. Borehole-wall breakouts were consistently located on the east and west sides of the boreholes. The orientation is consistent with previous estimates of the principal horizontal-stress field in south-central Washington, if breakouts are assumed to form along the azimuth of the least principal stress. The distribution of breakouts repeatedly indicated an interval of breakout-free rock at the top and bottom of flows. Because breakouts frequently terminate at major low-angle fractures, the data indicate that fracturing may have relieved some of the horizontal stresses near flow tops and bottoms. Unaltered and unfractured basalt appeared to have a uniform compressional velocity of 6.0 + or - 0.1 km/sec and a uniform shear velocity of 3.35 + or - 0.1 km/sec throughout flow interiors. Acoustics-waveform logs also indicated that borehole-wall breakouts did not affect acoustic propagation along the borehole; so fracturing associated with the formation of breakouts appeared to be confined to a thin annulus of stress concentration around the borehole. Televiewer logs obtained before and after hydraulic fracturing in these boreholes indicated the extent of induced fractures, and also indicated minor changes to pre-existing fractures that may have been inflated during fracture generation.

Washington↗
USGS2020

Spatial and vertical bias in down-looking ship-based acoustic estimates of fish density in Lake Superior: Lessons learned from multi-directional acoustics

Hydroacoustic surveys using hull-mounted down-looking transducers are useful for estimating pelagic fish densities; however, this method may miss shallow fish owing to the acoustic surface dead zone and vessel avoidance. Our objective was to compare pelagic fish density estimates acquired by a traditional down-looking acoustic survey to estimates obtained by a new multi-directional-towed sled capable of sampling the entire water column using upward-, sideways-, and downward-aimed transducers simultaneously. We deployed both systems concurrently in the western arm of Lake Superior during a period of stable stratification. We found the two survey approaches provided significantly different estimates of fish density in the upper water column layer (~4–9 m below the lake surface) with the sled up-looking transducer providing 56 times higher densities compared to the traditional ship down-looking method. Densities also varied significantly in the 9–14 m layer where densities were 6.2 times higher in the sled survey. Midwater trawl sampling indicated that cisco ( Coregonus artedi ) and rainbow smelt ( Osmerus mordax ) were the predominant species occupying the uppermost 14 m of the water column. The two acoustic approaches provided similar results at water column depths >14 m where rainbow smelt and kiyi ( Coregonus kiyi ) were predominant . Overall, the sled-based method estimates were, on average, 2.5 times higher for the whole water column. Our findings show that the new sled can reduce bias by better sampling the surface dead zone leading to more accurate estimation of pelagic fish densities for both management and research.

Lake Superior↗
USGS1999

Measurement of velocities with an acoustic velocity meter, one side-looking and two upward-looking acoustic Doppler current profilers in the Chicago Sanitary and Ship Canal, Romeoville, Illinois

In 1998, a prototype 300 kHz, side-looking Acoustic Doppler Current Profiler (ADCP) was deployed in the Chicago Sanitary and Ship Canal (CSSC) at Romeoville, Illinois. Additionally, two upward-looking ADCP's were deployed in the same acoustic path as the side-looking ADCP and in the reach defined by the upstream and downstream acoustic velocity meter (AVM) paths. All three ADCP's were synchronized to the AVM clock at the gaging station so that data were sampled simultaneously. The three ADCP's were deployed for six weeks measuring flow velocities from 0.0 to 2.5 ft/s. Velocities measured by each ADCP were compared to AVM path velocities and to velocities measured by the other ADCP's.

Proceedings of the IEEE Working Conference on Curr↗
USGS2009

Laboratory evaluation of an OTT acoustic digital current meter and a SonTek Laboratory acoustic Doppler velocimeter

Recently, an acoustic current meter known as the OTT * acoustic digital current meter (ADC) was introduced as an alternative instrument for stream gaging measurements. The Bureau of Reclamation and the U.S. Geological Survey collaborated on a side- by-side evaluation of the ADC and a SonTek/YSI acoustic Doppler velocimeter (ADV). Measurements were carried out in a laboratory flume to evaluate the performance characteristics of the ADC under a range of flow and boundary conditions. The flume contained a physical model of a mountain river with a diversion dam and variety of bed materials ranging from smooth mortar to a cobble bed. The instruments were installed on a trolley system that allowed them to be easily moved within the flume while maintaining a consistent probe orientation. More than 50 comparison measurements were made in an effort to verify the manufacturer’s performance specifications and to evaluate potential boundary disturbance for near-bed and vertical boundary measurements. Data and results from this evaluation are presented and discussed.

Conference Paper↗
USGS2016

Probability of acoustic transmitter detections by receiver lines in Lake Huron: results of multi-year field tests and simulations

Background Advances in acoustic telemetry technology have led to an improved understanding of the spatial ecology of many freshwater and marine fish species. Understanding the performance of acoustic receivers is necessary to distinguish between tagged fish that may have been present but not detected and from those fish that were absent from the area. In this study, two stationary acoustic transmitters were deployed 250 m apart within each of four acoustic receiver lines each containing at least 10 receivers (i.e., eight acoustic transmitters) located in Saginaw Bay and central Lake Huron for nearly 2 years to determine whether the probability of detecting an acoustic transmission varied as a function of time (i.e., season), location, and distance between acoustic transmitter and receiver. Distances between acoustic transmitters and receivers ranged from 200 m to >10 km in each line. The daily observed probability of detecting an acoustic transmission was used in simulation models to estimate the probability of detecting a moving acoustic transmitter on a line of receivers. Results The probability of detecting an acoustic transmitter on a receiver 1000 m away differed by month for different receiver lines in Lake Huron and Saginaw Bay but was similar for paired acoustic transmitters deployed 250 m apart within the same line. Mean probability of detecting an acoustic transmitter at 1000 m calculated over the study period varied among acoustic transmitters 250 m apart within a line and differed among receiver lines in Lake Huron and Saginaw Bay. The simulated probability of detecting a moving acoustic transmitter on a receiver line was characterized by short periods of time with decreased detection. Although increased receiver spacing and higher fish movement rates decreased simulated detection probability, the location of the simulated receiver line in Lake Huron had the strongest effect on simulated detection probability. Conclusions Performance of receiver lines in Lake Huron varied across a range of spatiotemporal scales and was inconsistent among receiver lines. Our simulations indicated that if 69 kHz acoustic transmitters operating at 158 dB in 10–30 m of freshwater were being used, then receivers should be placed 1000 m apart to ensure that all fish moving at 1 m s −1 or less will be detected 90% of days over a 2-year period. Whereas these results can be used as general guidelines for designing new studies, the irregular variation in acoustic transmitter detection probabilities we observed among receiver line locations in Lake Huron makes designing receiver lines in similar systems challenging and emphasizes the need to conduct post hoc analyses of acoustic transmitter detection probabilities.

Lake Huron↗
USGS2016

Long-term continuous acoustical suspended-sediment measurements in rivers - Theory, application, bias, and error

It is commonly recognized that suspended-sediment concentrations in rivers can change rapidly in time and independently of water discharge during important sediment‑transporting events (for example, during floods); thus, suspended-sediment measurements at closely spaced time intervals are necessary to characterize suspended‑sediment loads. Because the manual collection of sufficient numbers of suspended-sediment samples required to characterize this variability is often time and cost prohibitive, several “surrogate” techniques have been developed for in situ measurements of properties related to suspended-sediment characteristics (for example, turbidity, laser-diffraction, acoustics). Herein, we present a new physically based method for the simultaneous measurement of suspended-silt-and-clay concentration, suspended-sand concentration, and suspended‑sand median grain size in rivers, using multi‑frequency arrays of single-frequency side‑looking acoustic-Doppler profilers. The method is strongly grounded in the extensive scientific literature on the incoherent scattering of sound by random suspensions of small particles. In particular, the method takes advantage of theory that relates acoustic frequency, acoustic attenuation, acoustic backscatter, suspended-sediment concentration, and suspended-sediment grain-size distribution. We develop the theory and methods, and demonstrate the application of the method at six study sites on the Colorado River and Rio Grande, where large numbers of suspended-sediment samples have been collected concurrently with acoustic attenuation and backscatter measurements over many years. The method produces acoustical measurements of suspended-silt-and-clay and suspended-sand concentration (in units of mg/L), and acoustical measurements of suspended-sand median grain size (in units of mm) that are generally in good to excellent agreement with concurrent physical measurements of these quantities in the river cross sections at these sites. In addition, detailed, step-by-step procedures are presented for the general river application of the method. Quantification of errors in sediment-transport measurements made using this acoustical method is essential if the measurements are to be used effectively, for example, to evaluate uncertainty in long-term sediment loads and budgets. Several types of error analyses are presented to evaluate (1) the stability of acoustical calibrations over time, (2) the effect of neglecting backscatter from silt and clay, (3) the bias arising from changes in sand grain size, (4) the time-varying error in the method, and (5) the influence of nonrandom processes on error. Results indicate that (1) acoustical calibrations can be stable for long durations (multiple years), (2) neglecting backscatter from silt and clay can result in unacceptably high bias, (3) two frequencies are likely required to obtain sand-concentration measurements that are unbiased by changes in grain size, depending on site-specific conditions and acoustic frequency, (4) relative errors in silt-and-clay- and sand-concentration measurements decrease substantially as concentration increases, and (5) nonrandom errors may arise from slow changes in the spatial structure of suspended sediment that affect the relations between concentration in the acoustically ensonified part of the cross section and concentration in the entire river cross section. Taken together, the error analyses indicate that the two-frequency method produces unbiased measurements of suspended-silt-and-clay and sand concentration, with errors that are similar to, or larger than, those associated with conventional sampling methods.

Arizona, Texas↗
USGS2019

Temporally adaptive acoustic sampling to maximize detection across a suite of focal wildlife species

Acoustic recordings of the environment can produce species presence–absence data for characterizing populations of sound-producing wildlife over multiple spatial scales. If a species is present at a site but does not vocalize during a scheduled audio recording survey, researchers may incorrectly conclude that the species is absent (“false negative”). The risk of false negatives is compounded when audio devices have sampling constraints, do not record continuously, and must be manually scheduled to operate at pre-selected times of day, particularly when research programs target multiple species with acoustic availability that varies across temporal conditions. We developed a temporally adaptive acoustic sampling algorithm to maximize detection probabilities for a suite of focal species amid sampling constraints. The algorithm combines user-supplied species vocalization models with site-specific weather forecasts to set an optimized sampling schedule for the following day. To test our algorithm, we simulated hourly vocalization probabilities for a suite of focal species in a hypothetical monitoring area for the year 2016. We conducted a factorial experiment that sampled from the 2016 acoustic environment to compare the probability of acoustic detection by a fixed (stationary) schedule versus a temporally adaptive optimized schedule under several sampling efforts and monitoring durations. We found that over the course of a study season, the probability of acoustically capturing a focal species (given presence) at least once via automated acoustic monitoring was greater (and acoustic capture occurred earlier in the season) when using the temporally adaptive optimized schedule as compared to a fixed schedule. The advantages of a temporally adaptive optimized acoustic sampling schedule are magnified when a study duration is short, sampling effort is low, and/or species acoustic availability is minimal. This methodology presents the opportunity to maximize acoustic monitoring sampling efforts amid constraints.

Colorado↗
USGS2022

Characteristics, relationships and precision of direct acoustic-to-seismic coupling measurements from local explosions

Acoustic energy originating from explosions, sonic booms, bolides and thunderclaps have been recorded on seismometers since the 1950s. Direct pressure loading from the passing acoustic wave has been modelled and consistently observed to produce ground deformations of the near surface that have retrograde elliptical particle motions. In the past decade, increased deployments of colocated seismometers and infrasound sensors have driven efforts to use the transfer function between direct acoustic-to-seismic coupling to infer near-surface material properties including seismic velocity structure and elastic moduli. In this study, we use a small aperture (≈600 m) array of broadband seismometers installed in different manners and depths in both granite and sedimentary overburden to understand the fundamental nature and repeatability of seismic excitation from 1 to 15 Hz using horizontally propagating acoustic waves generated by 97 local (2–10 km) explosions. In agreement with modelling, we find that the ground motions induced by acoustic-to-seismic coupling attenuate rapidly with depth. We confirm the modelled relation between acoustic and ground motion amplitudes, but show that within one acoustic wavelength, the uncertainty in the transfer coefficient between seismic and acoustic energy at a given seismic station increases linearly with separation distance between the seismic and acoustic sensor. We attribute this observation to the rapid decorrelation of the infrasonic wavefield across small spatial scales and recommend colocating seismic and infrasound sensors for use in studies seeking to invert for near-surface material properties. Additionally, contrary to acoustic-to-seismic coupling theory and prior observations, we find that seismometers emplaced in granite do not record retrograde elliptical particle motions in response to direct pressure loading. We rule out seismometer tilt effects as a likely source of this observations and suggest that existing models of acoustic-to-seismic excitation may be too simplistic for seismometers placed in high rigidity materials.

Geophysical Journal International↗
USGS2016

Sediment acoustic index method for computing continuous suspended-sediment concentrations

Suspended-sediment characteristics can be computed using acoustic indices derived from acoustic Doppler velocity meter (ADVM) backscatter data. The sediment acoustic index method applied in these types of studies can be used to more accurately and cost-effectively provide time-series estimates of suspended-sediment concentration and load, which is essential for informed solutions to many sediment-related environmental, engineering, and agricultural concerns. Advantages of this approach over other sediment surrogate methods include: (1) better representation of cross-sectional conditions from large measurement volumes, compared to other surrogate instruments that measure data at a single point; (2) high temporal resolution of collected data; (3) data integrity when biofouling is present; and (4) less rating curve hysteresis compared to streamflow as a surrogate. An additional advantage of this technique is the potential expansion of monitoring suspended-sediment concentrations at sites with existing ADVMs used in streamflow velocity monitoring. This report provides much-needed standard techniques for sediment acoustic index methods to help ensure accurate and comparable documented results. A sediment acoustic index gage is used to collect continuous acoustic backscatter data, using an ADVM deployed in a fixed location, which are related to results from discrete suspended-sediment samples. The raw ADVM backscatter data are adjusted for variables affecting backscatter other than the sediment concentration to compute the sediment-corrected backscatter ( SCB ) and sediment attenuation coefficient ( SAC ). The sediment acoustic index rating (rating) is then developed by relating the sediment characteristics from the periodic samples to the SCB and (or) SAC and other explanatory variables in a site-specific, instrument-specific, simple or multiple linear regression model. The rating is reviewed and checked to ensure the technique has been applied appropriately. This review includes an assessment of the theoretical soundness, the adequacy of the model calibration dataset, and the quality of the regression model and regression diagnostics. The rating can then be applied to the acoustic surrogates and other explanatory variables to obtain continuous records of computed suspended-sediment concentration. The estimates of suspended-sediment concentration can then be paired with streamflow data, if available, to compute continuous records of suspended-sediment load. Once developed, sediment acoustic index ratings must be validated with additional suspended-sediment samples, beyond the period of record used in the rating development, to verify that the regression model continues to adequately represent sediment conditions within the stream. Changes in ADVM configuration or installation, or replacement with another ADVM, may require development of a new rating. The best practices described in this report can be used to develop continuous estimates of suspended-sediment concentration and load using sediment acoustic surrogates to enable more informed and accurate responses to diverse sedimentation issues.

Techniques and Methods↗
USGS2022

Field testing a high-frequency acoustic attenuation system for measuring fine suspended sediments and algal movements

Acoustic measurements of suspended sediment have the potential to allow remote, autonomous monitoring of sediment movements at much higher temporal resolution than traditional manual sampling methods. Although suspended sands present a challenging measurement problem due to their logarithmic distribution with depth, fine clay sediments are distributed evenly throughout a stream cross section, making them amenable to point measurements. In order to improve measurement capabilities for fine sediments in stream channels, The National Center for Physical Acoustics at The University of Mississippi has developed a remote, autonomous acoustic system to monitor fine sediments transported in streams. The system was tested on the Middle Rio Grande near San Acacia, New Mexico, and in Goodwin Creek in Panola County, Mississippi. The acoustic instruments were compared to sediment concentrations from physical samples in both deployments. Diurnal patterns were found in the acoustic signals from the Middle Rio Grande, and a follow up experiment at The University of Mississippi Biological Field Station was used to investigate the potential effects of algal biomass on acoustic attenuation measurements. The results showed diurnal patterns in attenuation were associated with patterns in light, temperature, and dissolved oxygen. These results combined with information from the literature indicate diel movement of algal colonies in the water column of some water bodies may interfere with high-frequency acoustic measurements in natural environments and that acoustic methods have the potential to allow ecological researchers to evaluate mass algal movements in the field. Results from Goodwin Creek demonstrate that the acoustic system is able to provide measurements of sediment concentration with high temporal resolution that track well with expected sediment transport patterns in response to discharge hydrographs.

Applied Acoustics↗
USGS2006

Seismo-acoustic signals associated with degassing explosions recorded at Shishaldin Volcano, Alaska, 2003-2004

In summer 2003, a Chaparral Model 2 microphone was deployed at Shishaldin Volcano, Aleutian Islands, Alaska. The pressure sensor was co-located with a short-period seismometer on the volcano’s north flank at a distance of 6.62 km from the active summit vent. The seismo-acoustic data exhibit a correlation between impulsive acoustic signals (1–2 Pa) and long-period (LP, 1–2 Hz) earthquakes. Since it last erupted in 1999, Shishaldin has been characterized by sustained seismicity consisting of many hundreds to two thousand LP events per day. The activity is accompanied by up to ∼200 m high discrete gas puffs exiting the small summit vent, but no significant eruptive activity has been confirmed. The acoustic waveforms possess similarity throughout the data set (July 2003–November 2004) indicating a repetitive source mechanism. The simplicity of the acoustic waveforms, the impulsive onsets with relatively short (∼10–20 s) gradually decaying codas and the waveform similarities suggest that the acoustic pulses are generated at the fluid–air interface within an open-vent system. SO 2 measurements have revealed a low SO 2 flux, suggesting a hydrothermal system with magmatic gases leaking through. This hypothesis is supported by the steady-state nature of Shishaldin’s volcanic system since 1999. Time delays between the seismic LP and infrasound onsets were acquired from a representative day of seismo-acoustic data. A simple model was used to estimate source depths. The short seismo-acoustic delay times have revealed that the seismic and acoustic sources are co-located at a depth of 240±200 m below the crater rim. This shallow depth is confirmed by resonance of the upper portion of the open conduit, which produces standing waves with f =0.3 Hz in the acoustic waveform codas. The infrasound data has allowed us to relate Shishaldin’s LP earthquakes to degassing explosions, created by gas volume ruptures from a fluid–air interface.

Alaska↗
USGS2014

Use of acoustic backscatter to estimate continuous suspended sediment and phosphorus concentrations in the Barton River, northern Vermont, 2010-2013

The U.S. Geological Survey, in cooperation with the Vermont Department of Environmental Conservation, investigated the use of acoustic backscatter to estimate concentrations of suspended sediment and total phosphorus at the Barton River near Coventry, Vermont. The hypothesis was that acoustic backscatter—the reflection of sound waves off objects back to the source from which they came—measured by an acoustic Doppler profiler (ADP) and recorded as ancillary data for the calculation of discharge, also could be used to generate a continuous concentration record of suspended sediment and phosphorus at the streamgage, thereby deriving added value from the instrument. Suspended-sediment and phosphorus concentrations are of particular interest in Vermont, where impairment of surface waters by suspended sediments and phosphorus is a major concern. Regression models for estimating suspended-sediment concentrations (SSCs) and total phosphorus concentrations evaluated several independent variables: measured backscatter (MB), water-corrected backscatter (WCB), sediment-corrected backscatter (SCB), discharge, fluid-absorption coefficient, sediment-driven acoustic attenuation coefficient, and discharge hysteresis. The best regression equations for estimating SSC used backscatter as the predictor, reflecting the direct relation between acoustic backscatter and SSC. Backscatter was a better predictor of SSC than discharge in part because hysteresis between SSC and backscatter was less than for SSC and discharge. All three backscatter variables—MB, WCB, and SCB—performed equally as predictors of SSC and phosphorus concentrations at the Barton River site. The similar abilities to predict SSC among backscatter terms may partially be attributed to the low values and narrow range of the sediment-driven acoustic attenuation in the Barton River. The regression based on SCB was selected for estimating SSC because it removes potential bias caused by attenuation and temperature fluctuations. The best regression model for estimating phosphorus concentrations included terms for discharge and discharge hysteresis. The finding that discharge hysteresis was a significant predictor of phosphorus concentrations might be related to preferential sorption of phosphorus to fine-grained sediments, which have been found to be particularly sensitive to hysteresis. Regression models designed to estimate phosphorus concentrations had less predictive power than the models for SSCs. Data from the Barton River did not fully support one of the study’s hypotheses—that backscatter is mostly caused by sands, and attenuation is mostly caused by fines. Sands, fines, and total SSCs in the Barton River all related better to backscatter than to sediment-driven acoustic attenuation. The weak relation between SSC and sediment-driven acoustic attenuation may be related to the low values and narrow range of SSCs and sediment attenuations observed at Barton River. A weak relation between SSC and sediment-driven acoustic attenuation also suggests that the diameters of the fine-sized suspended sediments in the Barton River may be predominantly greater than 20 micrometers (μm). Long-term changes in the particle-size distribution (PSD) were not observed in Barton River; however, some degree of within-storm changes in sediment source and possibly PSD were inferred from the hysteresis between SSC and SCB.

Vermont↗
USGS2022

Categorizing active marine acoustic sources based on their potential to affect marine animals

Marine acoustic sources are widely used for geophysical imaging, oceanographic sensing, and communicating with and tracking objects or robotic vehicles in the water column. Under the U.S. Marine Mammal Protection Act and similar regulations in several other countries, the impact of controlled acoustic sources is assessed based on whether the sound levels received by marine mammals meet the criteria for harassment that causes certain behavioral responses. This study describes quantitative factors beyond received sound levels that could be used to assess how marine species are affected by many commonly deployed marine acoustic sources, including airguns, high-resolution geophysical sources (e.g., multibeam echosounders, sidescan sonars, subbottom profilers, boomers, and sparkers), oceanographic instrumentation (e.g., acoustic doppler current profilers, split-beam fisheries sonars), and communication/tracking sources (e.g., acoustic releases and locators, navigational transponders). Using physical criteria about the sources, such as source level, transmission frequency, directionality, beamwidth, and pulse repetition rate, we divide marine acoustic sources into four tiers that could inform regulatory evaluation. Tier 1 refers to high-energy airgun surveys with a total volume larger than 1500 in 3 (24.5 L) or arrays with more than 12 airguns, while Tier 2 covers the remaining low/intermediate energy airgun surveys. Tier 4 includes most high-resolution geophysical, oceanographic, and communication/tracking sources, which are considered unlikely to result in incidental take of marine mammals and therefore termed de minimis . Tier 3 covers most non-airgun seismic sources, which either have characteristics that do not meet the de minimis category (e.g., some sparkers) or could not be fully evaluated here (e.g., bubble guns, some boomers). We also consider the simultaneous use of multiple acoustic sources, discuss marine mammal field observations that are consistent with the de minimis designation for some acoustic sources, and suggest how to evaluate acoustic sources that are not explicitly considered here.

Journal of Marine Science and Engineering↗
USGS2017

Comparison of acoustic recorders and field observers for monitoring tundra bird communities

Acoustic recorders can be useful for studying bird populations but their efficiency and accuracy should be assessed in pertinent ecological settings before use. We investigated the utility of an acoustic recorder for monitoring abundance of tundra‐breeding birds relative to point‐count surveys in northwestern Alaska, USA, during 2014. Our objectives were to 1) compare numbers of birds and species detected by a field observer with those detected simultaneously by an acoustic recorder; 2) evaluate how detection probabilities for the observer and acoustic recorder varied with distance of birds from the survey point; and 3) evaluate whether avian guild‐specific detection rates differed between field observers and acoustic recorders relative to habitat. Compared with the observer, the acoustic recorder detected fewer species (β Method = −0.39 ± 0.07) and fewer individuals (β Method = −0.56 ± 0.05) in total and for 6 avian guilds. Discrepancies were attributed primarily to differences in effective area surveyed (91% missed by device were >100 m), but also to nonvocal birds being missed by the recorder (55% missed <100 m were silent). The observer missed a few individuals and one species detected by the device. Models indicated that relative abundance of various avian guilds was associated primarily with maximum shrub height and less so with shrub cover and visual obstruction. The absence of a significant interaction between survey method (observer vs . acoustic recorder) and any habitat characteristic suggests that traditional point counts and acoustic recorders would yield similar inferences about ecological relationships in tundra ecosystems. Pairing of the 2 methods could increase survey efficiency and allow for validation and archival of survey results.

Alaska↗
USGS2020

Acoustic space occupancy: Combining ecoacoustics and lidar to model biodiversity variation and detection bias across heterogeneous landscapes

There is global interest in quantifying changing biodiversity in human-modified landscapes. Ecoacoustics may offer a promising pathway for supporting multi-taxa monitoring, but its scalability has been hampered by the sonic complexity of biodiverse ecosystems and the imperfect detectability of animal-generated sounds. The acoustic signature of a habitat, or soundscape, contains information about multiple taxa and may circumvent species identification, but robust statistical technology for characterizing community-level attributes is lacking. Here, we present the Acoustic Space Occupancy Model, a flexible hierarchical framework designed to account for detection artifacts from acoustic surveys in order to model biologically relevant variation in acoustic space use among community assemblages. We illustrate its utility in a biologically and structurally diverse Amazon frontier forest landscape, a valuable test case for modeling biodiversity variation and acoustic attenuation from vegetation density. We use complementary airborne lidar data to capture aspects of 3D forest structure hypothesized to influence community composition and acoustic signal detection. Our novel analytic framework permitted us to model both the assembly and detectability of soundscapes using lidar-derived estimates of forest structure. Our empirical predictions were consistent with physical models of frequency-dependent attenuation, and we estimated that the probability of observing animal activity in the frequency channel most vulnerable to acoustic attenuation varied by over 60%, depending on vegetation density. There were also large differences in the biotic use of acoustic space predicted for intact and degraded forest habitats, with notable differences in the soundscape channels predominantly occupied by insects . This study advances the utility of ecoacoustics by providing a robust modeling framework for addressing detection bias from remote audio surveys while preserving the rich dimensionality of soundscape data, which may be critical for inferring biological patterns pertinent to multiple taxonomic groups in the tropics. Our methodology paves the way for greater integration of remotely sensed observations with high-throughput biodiversity data to help bring routine, multi-taxa monitoring to scale in dynamic and diverse landscapes.

Mato Grosso↗
USGS2004

Estimating suspended solids concentrations from backscatter intensity measured by acoustic Doppler current profiler in San Francisco Bay, California

The estimation of mass concentration of suspended solids is one of the properties needed to understand the characteristics of sediment transport in bays and estuaries. However, useful measurements or estimates of this property are often problematic when employing the usual methods of determination from collected water samples or optical sensors. Analysis of water samples tends to undersample the highly variable character of suspended solids, and optical sensors often become useless from biological fouling in highly productive regions. Acoustic sensors, such as acoustic Doppler current profilers that are now routinely used to measure water velocity, have been shown to hold promise as a means of quantitatively estimating suspended solids from acoustic backscatter intensity, a parameter used in velocity measurement. To further evaluate application of this technique using commercially available instruments, profiles of suspended solids concentrations are estimated from acoustic backscatter intensity recorded by 1200- and 2400-kHz broadband acoustic Doppler current profilers located at two sites in San Francisco Bay, California. ADCP backscatter intensity is calibrated using optical backscatterance data from an instrument located at a depth close to the ADCP transducers. In addition to losses from spherical spreading and water absorption, calculations of acoustic transmission losses account for attenuation from suspended sediment and correction for nonspherical spreading in the near field of the acoustic transducer. Acoustic estimates of suspended solids consisting of cohesive and noncohesive sediments are found to agree within about 8-10% (of the total range of concentration) to those values estimated by a second optical backscatterance sensor located at a depth further from the ADCP transducers. The success of this approach using commercially available Doppler profilers provides promise that this technique might be appropriate and useful under certain conditions in spite of some theoretical limitations of the method. ?? 2004 Elsevier B.V. All rights reserved.

Marine Geology↗
USGS2025

Simulated soundscapes and transfer learning boost the performance of acoustic classifiers under data scarcity

1. The biodiversity crisis necessitates spatially extensive methods to monitor multiple taxonomic groups for evidence of change in response to evolving environmental conditions. Programs that combine passive acoustic monitoring and machine learning are increasingly used to meet this need. These methods require large, annotated datasets, which are time-consuming and expensive to produce, creating potential barriers to adoption in data- and funding-poor regions. Recently released pre-trained avian acoustic classification models provide opportunities to reduce the need for manual labelling and accelerate the development of new acoustic classification algorithms through transfer learning. Transfer learning is a strategy for developing algorithms under data scarcity that uses pre-trained models from related tasks to adapt to new tasks. 2. Our primary objective was to develop a transfer learning strategy using the feature embeddings of a pre-trained avian classification model to train custom acoustic classification models in data-scarce contexts. We used three annotated avian acoustic datasets to test whether transfer learning and soundscape simulation-based data augmentation could substantially reduce the annotated training data necessary to develop performant custom acoustic classifiers. We also conducted a sensitivity analysis for hyperparameter choice and model architecture. We then assessed the generalizability of our strategy to increasingly novel non-avian classification tasks. 3. With as few as two training examples per class, our soundscape simulation data augmentation approach consistently yielded new classifiers with improved performance relative to the pre-trained classification model and transfer learning classifiers trained with other augmentation approaches. Performance increases were evident for three avian test datasets, including single-class and multi-label contexts. We observed that the relative performance among our data augmentation approaches varied for the avian datasets and nearly converged for one dataset when we included more training examples. 4. We demonstrate an efficient approach to developing new acoustic classifiers leveraging open-source sound repositories and pre-trained networks to reduce manual labelling. With very few examples, our soundscape simulation approach to data augmentation yielded classifiers with performance equivalent to those trained with many more examples, showing it is possible to reduce manual label-ling while still achieving high-performance classifiers and, in turn, expanding the potential for passive acoustic monitoring to address rising biodiversity monitoring needs.

Methods in Ecology and Evolution↗
USGS2016

Estimating suspended sediment using acoustics in a fine-grained riverine system, Kickapoo Creek at Bloomington, Illinois

Acoustic technologies have the potential to be used as a surrogate for measuring suspended-sediment concentration (SSC). This potential was examined in a fine-grained (97-100 percent fines) riverine system in central Illinois by way of installation of an acoustic instrument. Acoustic data were collected continuously over the span of 5.5 years. Acoustic parameters were regressed against SSC data to determine the accuracy of using acoustic technology as a surrogate for measuring SSC in a fine-grained riverine system. The resulting regressions for SSC and sediment acoustic parameters had coefficients of determination ranging from 0.75 to 0.97 for various events and configurations. The overall Nash-Sutcliffe model-fit efficiency was 0.95 for the 132 observed and predicted SSC values determined using the sediment acoustic parameter regressions. The study of using acoustic technologies as a surrogate for measuring SSC in fine-grained riverine systems is ongoing. The results at this site are promising in the realm of surrogate technology.

Illinois↗