USGS Science⌕ Search

SEARCH · USGS Science

Results for “groundwater aquifer”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94Linked to original sources
USGS1993

Public-supply water use in Florida, 1990

In 1990, public supply withdrawals represented nearly 26 percent of the total freshwater withdrawn in Florida. Total water withdrawn for public supply in Florida during 1990 averaged 1,925 million gal/day. Public suppliers served 11.23 million residents, in 1990. Groundwater was the source for more than 88 percent (1,699 million gal/day) of public-supply withdrawals and was used by more than 10.0 million residents; surface water was the source of the remaining 12 percent (226 million gal/day) and was used by about 1.2 million residents. The Floridan aquifer system was the source of the majority of groundwater in 1990 (50 percent), followed by the Biscayne aquifer (34 percent). Public-supply water withdrawals peaked in May 1990 at 2,140 million gal/day, primarily because of an increase in the residential demands for lawn irrigation. During 1990, withdrawals for January were lowest (1,870 million gal/day), nearly 270 million gal/day less than in May. Public-supply per capita use for Florida in 1990 was 171 gal/day and domestic (residential) per capita use was 111 gal/day. The population of Florida increased from 9.75 million in 1980 to more than 12.94 million in 1990, and the percentage of the population served by public supply increased from 80 percent in 1980 to 87 percent in 1990. Public-supply water with- drawals in Florida increased 41 percent between 1980 and 1990 even though public supply per capita use has remained fairly consistent since 1980. Public water suppliers in Dade County withdrew the largest amount of water (326 million gal/day) for public supply in the State for 1990 and served nearly 1.88 million people. (USGS)

Open-File Report↗
USGS2000

Water levels and ground-water discharge, regional aquifer system of the midwestern Basins and Arches Region, in parts of Indiana, Ohio, Illinois, and Michigan

Aquifers in Quaternary glacial deposits and the underlying Silurian and Devonian carbonate bedrock in parts of Indiana, Ohio, Illinois, and Michigan compose the regional aquifer system under investigation as part of the Midwestern Basins and Arches Regional Aquifer System Analysis (Midwestern Basins and Arches—RASA) project of the U.S. Geological Survey (USGS). The Midwestern Basins and Arches—RASA is part of a USGS program to assess the regional hydrology, geology, and water quality of the Nation's most important aquifers (Sun, 1986). An objective specific to the Midwestern Basins and Arches—RASA project is to conceptualize and describe regional ground-water flow in the glacial-deposit and carbonate-bedrock aquifer system, including regional recharge and discharge areas and regional relations between surface and ground water (Bugliosi, 1990). Water-level and ground-water discharge data were collected and (or) analyzed to help meet the above objective. Specifically, data from the USGS Ground-Water Site Inventory (GWSI) data base were used to determine relations between land-surface altitude and water levels in glacial-deposit aquifers. Water levels in the carbonate-bedrock aquifer were synoptically measured during July 1990, and the data were used to construct a potentiometric surface map of the aquifer. Regional hydraulic gradients and general directions of regional flow in the carbonate-bedrock aquifer can be inferred from this map. Steady-state groundwater discharge to streams that drain the area underlain by the glacial-deposit and carbonate bedrock aquifer system was estimated from base-flow daily values computed from streamflow records. Water-level and ground-water-discharge data collectively form the sample information necessary to develop calibration targets for calibration of a ground-water-flow model (Anderson and Woessner, 1992). Such a ground-water-flow model of the glacial-deposit and carbonate-bedrock aquifer system was constructed to help conceptualize and describe regional ground-water flow in the aquifer system. The model was calibrated to the water-level and ground-water-discharge data presented in this atlas.

Hydrologic Atlas↗
USGS2013

Hydrogeology of the Susquehanna River valley-fill aquifer system and adjacent areas in eastern Broome and southeastern Chenango Counties, New York

The hydrogeology of the valley-fill aquifer system along a 32-mile reach of the Susquehanna River valley and adjacent areas was evaluated in eastern Broome and southeastern Chenango Counties, New York. The surficial geology, inferred ice-marginal positions, and distribution of stratified-drift aquifers were mapped from existing data. Ice-marginal positions, which represent pauses in the retreat of glacial ice from the region, favored the accumulation of coarse-grained deposits whereas more steady or rapid ice retreat between these positions favored deposition of fine-grained lacustrine deposits with limited coarse-grained deposits at depth. Unconfined aquifers with thick saturated coarse-grained deposits are the most favorable settings for water-resource development, and three several-mile-long sections of valley were identified (mostly in Broome County) as potentially favorable: (1) the southernmost valley section, which extends from the New York–Pennsylvania border to about 1 mile north of South Windsor, (2) the valley section that rounds the west side of the umlaufberg (an isolated bedrock hill within a valley) north of Windsor, and (3) the east–west valley section at the Broome County–Chenango County border from Nineveh to East of Bettsburg (including the lower reach of the Cornell Brook valley). Fine-grained lacustrine deposits form extensive confining units between the unconfined areas, and the water-resource potential of confined aquifers is largely untested. Recharge, or replenishment, of these aquifers is dependent not only on infiltration of precipitation directly on unconfined aquifers, but perhaps more so from precipitation that falls in adjacent upland areas. Surface runoff and shallow groundwater from the valley walls flow downslope and recharge valley aquifers. Tributary streams that drain upland areas lose flow as they enter main valleys on permeable alluvial fans. This infiltrating water also recharges valley aquifers. Current (2012) use of water resources in the area is primarily through domestic wells, most of which are completed in fractured bedrock in upland areas. A few villages in the Susquehanna River valley have supply wells that draw water from beneath alluvial fans and near the Susquehanna River, which is a large potential source of water from induced infiltration.

New York↗
USGS2001

Ground water near Newton, Jasper County, Iowa

The U.S. Geological Survey, in cooperation with the city of Newton, Iowa, conducted an investigation of the ground-water resources of Jasper County, Iowa, near Newton during 1999-2001. The purpose of the investigation was to provide additional information on the South Skunk River alluvial aquifer from which Newton obtains its present municipal supply and to summarize the available information on other groundwater resources in the county. The South Skunk River alluvial aquifer consists of unconsolidated deposits of sand and gravel of glacial and fluvial origin. These deposits overlie bedrock composed primarily of shale and limestone of Pennsylvanian or Mississippian age. Information on the South Skunk River alluvial aquifer and other Jasper County alluvial aquifers is limited to a few test holes in a few locations. Additional thickness and lithologic information was collected using seismic refraction and test hole drilling to increase the understanding of the South Skunk River alluvial aquifer near Newton. Water-level and water-quality information also was collected. The alluvial deposits along the South Skunk River near Newton range from less than 30 to more than 60 feet thick. Three areas of deposits exceeding 60 feet thick occur near the present city of Newton well field about 5,000 feet west of the present well field, at the present well field, and about 5,000 feet southeast of the present well field. Ground water in the South Skunk River alluvial aquifer near the Newton well field flows toward the municipal well field. Ground-water levels on the well-field side of the South Skunk River were lower than water levels in the river, indicating flow from the river toward the well field. The water quality in the South Skunk River and the alluvial aquifer was similar, except most ground-water samples contained low dissolved oxygen concentrations. The low dissolved-oxygen concentrations in ground water resulted in high concentrations of iron and manganese in some locations and reduced forms of nitrogen.

Iowa↗
USGS2003

Stable lead isotopes reveal a natural source of high lead concentrations to gasoline-contaminated groundwater

Concentrations of total lead as high as 1,600 μg/L were detected in gasoline-contaminated and uncontaminated groundwater at three gasoline-release sites in South Carolina. Total lead concentrations were highest in turbid groundwater samples from gasoline-contaminated and uncontaminated wells, whereas lower turbidity groundwater samples (collected using low-flow methods) had lower total lead concentrations. Dissolved lead concentrations in all wells sampled, however, were less than 15 μg total lead/L, the current United States Environmental Protection Agency (US EPA) maximum contaminant level (MCL). Because many total lead concentrations exceeded the MCL, the source of lead to the groundwater system at two of the three sites was investigated using a stable lead isotope ratio approach. Plots of the stable isotope ratios of lead (Pb) in groundwater as 207 Pb/ 206 Pb versus 208 Pb/ 206 Pb, and 208 Pb/ 204 Pb versus 206 Pb/ 204 Pb were similar to ratios characteristic of lead-based minerals in local rocks of the southeastern US, and were not similar to the stable lead isotopes ratios characteristic of distant lead ore deposits such as Broken Hill, Australia, used to produce tetraethyl lead in gasoline products prior to its phase-out and ban in the United States. Moreover, the isotopic composition of dissolved lead was equivalent to the isotopic composition of total lead in turbid samples collected from the same well, suggesting that the majority of the lead detected in the groundwater samples was associated with sediment particulates of indigenous aquifer material, rather than lead associated with spilled leaded gasoline. The results of this investigation indicate that (1) lead detected at some gasoline-release sites may be derived from the local aquifer material, rather than the gasoline release, and consequently may affect site-specific remediation goals; (2) non-low flow groundwater sampling methods, such as a disposable bailer, may result in turbid groundwater samples and high total lead concentrations, and; (3) stable lead isotopes can be used to clarify the source of lead detected above permissible levels in gasoline-contaminated groundwater systems.

Environmental Geology↗
USGS2004

Approaches to surface complexation modeling of Uranium(VI) adsorption on aquifer sediments

Uranium(VI) adsorption onto aquifer sediments was studied in batch experiments as a function of pH and U(VI) and dissolved carbonate concentrations in artificial groundwater solutions. The sediments were collected from an alluvial aquifer at a location upgradient of contamination from a former uranium mill operation at Naturita, Colorado (USA). The ranges of aqueous chemical conditions used in the U(VI) adsorption experiments (pH 6.9 to 7.9; U(VI) concentration 2.5 · 10 −8 to 1 · 10 −5 M; partial pressure of carbon dioxide gas 0.05 to 6.8%) were based on the spatial variation in chemical conditions observed in 1999–2000 in the Naturita alluvial aquifer. The major minerals in the sediments were quartz, feldspars, and calcite, with minor amounts of magnetite and clay minerals. Quartz grains commonly exhibited coatings that were greater than 10 nm in thickness and composed of an illite-smectite clay with occluded ferrihydrite and goethite nanoparticles. Chemical extractions of quartz grains removed from the sediments were used to estimate the masses of iron and aluminum present in the coatings. Various surface complexation modeling approaches were compared in terms of the ability to describe the U(VI) experimental data and the data requirements for model application to the sediments. Published models for U(VI) adsorption on reference minerals were applied to predict U(VI) adsorption based on assumptions about the sediment surface composition and physical properties (e.g., surface area and electrical double layer). Predictions from these models were highly variable, with results overpredicting or underpredicting the experimental data, depending on the assumptions used to apply the model. Although the models for reference minerals are supported by detailed experimental studies (and in ideal cases, surface spectroscopy), the results suggest that errors are caused in applying the models directly to the sediments by uncertain knowledge of: 1) the proportion and types of surface functional groups available for adsorption in the surface coatings; 2) the electric field at the mineral-water interface; and 3) surface reactions of major ions in the aqueous phase, such as Ca 2+ , Mg 2+ , HCO 3 − , SO 4 2− , H 4 SiO 4 , and organic acids. In contrast, a semi-empirical surface complexation modeling approach can be used to describe the U(VI) experimental data more precisely as a function of aqueous chemical conditions. This approach is useful as a tool to describe the variation in U(VI) retardation as a function of chemical conditions in field-scale reactive transport simulations, and the approach can be used at other field sites. However, the semi-empirical approach is limited by the site-specific nature of the model parameters.

Geochimica et Cosmochimica Acta↗
USGS2014

Using state-of-the-art technology to evaluate saltwater intrusion in the Biscayne aquifer of Miami-Dade County, Florida

The fresh groundwater supplies of many communities have been adversely affected or limited by saltwater intrusion. An insufficient understanding of the origin of intruded saltwater may lead to inefficient or ineffective water-resource management. A 2008–2012 cooperative U.S. Geological Survey (USGS) and Miami-Dade County study of saltwater intrusion describes state-of-the art technology used to evaluate the origin and distribution of this saltwater.

Florida↗
USGS1987

Hydrologic effects of artificial-recharge experiments with reclaimed water at East Meadow, Long Island, New York

Artificial recharge experiments were conducted at East Meadow, Long Island, New York, from October 1982 through January 1984 to evaluate the degree of groundwater mounding and the chemical effects of artificially replenishing the groundwater system with tertiary-treated wastewater. More than 800 million gallons of treated effluent was returned to the upper glacial aquifer through recharge basins and injection wells in the 15-month period. Reclaimed water was provided by the Cedar Creek advanced wastewater treatment facility in Wantagh, 6 miles away. The chlorinated effluent was pumped to the recharge facility, where it was fed to basins by gravity flow and to injection wells by pumps. Observations during the recharge tests indicate that the two most significant factors in limiting the rate of infiltration through the basin floor were the recharge test duration and quality of reclaimed water. Head buildup in the aquifer beneath the basins ranged from 4.3 to 6.7 ft, depending on the quantity and duration of water application. Head buildup near the injection wells within the aquifer ranged from 0.3 to 1.2 ft. Recharge basins provided a more effective means of moving large quantities of reclaimed water into the aquifer than injection wells. Results of 3-day and 176-day ponding tests in two basins indicate that reclaimed water is relatively unchanged chemically by percolation through the unsaturated zone because: (1) the sand and gravel of the upper glacial aquifer is unreactive, (2) the water moves to the water table rapidly, and (3) the water is highly treated before recharge. The quality of water in the aquifer zones affected by recharge improved, on the whole. Groundwater concentrations of nitrate nitrogen and several low molecular weight hydrocarbons, decreased to well within drinking water standards as a direct result of recharge. Sodium and chloride concentrations increased above background levels as a result of recharge but remained well within drinking water standards and the New York State effluent standards established for this groundwater recharge study. (Lantz-PTT)

Water-Resources Investigations Report↗
USGS2023

Quality of groundwater used for domestic supply in the Modesto, Turlock, and Merced Subbasins of the San Joaquin Valley, California

Summary More than 2 million Californians rely on groundwater from privately owned domestic wells for drinking-water supply. This report summarizes a water-quality survey of domestic and small-system drinking-water supply wells in the Modesto, Turlock, and Merced subbasins of the San Joaquin Valley where more than 78,000 residents are estimated to use privately owned domestic wells. Results indicate that inorganic and organic constituents in groundwater were respectively present above regulatory (maximum contaminant level, MCL) benchmarks for public drinking-water quality in 37 percent and 9 percent of the aquifer area used for domestic drinking-water supplies (herein, “domestic groundwater resources”). The most prevalent inorganic constituents exceeding regulatory benchmarks were nitrate, uranium, and arsenic. The only organic constituents exceeding regulatory benchmarks were the fumigant constituents 1,2,3-trichloropropane (1,2,3-TCP) and 1,2-dibromo-3-chloropropane (DBCP), but the herbicides atrazine and simazine were detected at low concentrations below one-tenth of regulatory benchmarks in 30 percent of domestic groundwater resources. Total dissolved solids (TDS) and manganese exceeded aesthetic-based (secondary maximum contaminant level [SMCL]) benchmarks for drinking water in 3 percent and 13 percent of domestic groundwater resources, respectively. Per- and polyfluoroalkyl substances (PFAS) were detected in 23 percent of domestic groundwater resources, with 4 percent exceeding California state notification or response levels for specific compounds. Total coliform bacteria were detected in 20 percent of domestic groundwater resources. Elevated concentrations of nitrate, uranium, TDS, and pesticides (fumigant constituents and herbicides) are related to agricultural land use and were typically present at shallow depths up to 75 meters below land surface. Agriculturally derived constituents were detected in wells screened below the Corcoran Clay Member of the Tulare Formation (herein, “Corcoran Clay”) in the southeastern part of the study area, where the Corcoran Clay tends to be shallower and thinner than in areas to the northwest. Nitrate, uranium, and TDS were most prevalent in the northwest part of the study area proximal to the valley trough where soils are poorly drained and agricultural land uses are predominantly grain, alfalfa, and dairy farms. Pesticides tended to occur in groundwater below coarse-grained surficial deposits and within a northwest to southeast trending band along the eastern extent of the Corcoran Clay that typically demarcates the western extent of well-drained soils associated with perennial orchard crops. Elevated concentrations of arsenic tended to occur west of this band in reducing groundwater but also sometimes co-occurred with elevated nitrate in oxic groundwater, most likely because of geochemical conditions in agriculturally affected groundwater that can enhance the mobility of arsenic from aquifer sediments.

California↗
USGS2021

Effects of climate and irrigation on GRACE-based estimates of water storage changes in major US aquifers

Understanding climate and human impacts on water storage is critical for sustainable water-resources management. Here we assessed climate and human drivers of total water storage (TWS) variability from Gravity Recovery and Climate Experiment (GRACE) satellites compared with drought severity and irrigation water use in 14 major aquifers in the United States. Results show that long-term variability in TWS tracked by GRACE satellites is dominated by interannual variability in most of the 14 major US aquifers. Low TWS trends in the humid eastern U.S. are linked to low drought intensity. Although irrigation pumpage in the humid Mississippi Embayment aquifer exceeded that in the semi-arid California Central Valley, a surprising lack of TWS depletion in the Mississippi Embayment aquifer is attributed to extensive streamflow capture. Marked storage depletion in the semi-arid southwestern Central Valley and south-central High Plains totaled ∼90 km 3 , about three times greater than the capacity of Lake Mead, the largest U.S. reservoir. Depletion in the Central Valley was driven by long-term droughts (⩽5 yr) amplified by switching from mostly surface water to groundwater irrigation. Low or slightly rising TWS trends in the northwestern (Columbia and Snake Basins) US are attributed to dampening drought impacts by mostly surface water irrigation. GRACE satellite data highlight synergies between climate and irrigation, resulting in little impact on TWS in the humid east, amplified TWS depletion in the semi-arid southwest and southcentral US, and dampened TWS deletion in the northwest and north central US Sustainable groundwater management benefits from conjunctive use of surface water and groundwater, inefficient surface water irrigation promoting groundwater recharge, efficient groundwater irrigation minimizing depletion, and increasing managed aquifer recharge. This study has important implications for sustainable water development in many regions globally.

Environmental Research Letters↗
USGS2011

Hydrogeologic and geochemical characterization of groundwater resources in Rush Valley, Tooele County, Utah

The water resources of Rush Valley were assessed during 2008–2010 with an emphasis on refining the understanding of the groundwater-flow system and updating the groundwater budget. Surface-water resources within Rush Valley are limited and are generally used for agriculture. Groundwater is the principal water source for most other uses including supplementing irrigation. Most groundwater withdrawal in Rush Valley is from the unconsolidated basin-fill aquifer where conditions are generally unconfined near the mountain front and confined at lower altitudes near the valley center. Productive aquifers also occur in fractured bedrock along the valley margins and beneath the basin-fill deposits in some areas. Drillers’ logs and geophysical gravity data were compiled and used to delineate seven hydrogeologic units important to basin-wide groundwater movement. The principal basin-fill aquifer includes the unconsolidated Quaternary-age alluvial and lacustrine deposits of (1) the upper basin-fill aquifer unit (UBFAU) and the consolidated and semiconsolidated Tertiary-age lacustrine and alluvial deposits of (2) the lower basin-fill aquifer unit (LBFAU). Bedrock hydrogeologic units include (3) the Tertiary-age volcanic unit (VU), (4) the Pennsylvanian- to Permian-age upper carbonate aquifer unit (UCAU), (5) the upper Mississippian- to lower Pennsylvanian-age upper siliciclastic confining unit (USCU), (6) the Middle Cambrian- to Mississippian-age lower carbonate aquifer unit (LCAU), and (7) the Precambrian- to Lower Cambrian-age noncarbonate confining unit (NCCU). Most productive bedrock wells in the Rush Valley groundwater basin are in the UCAU. Average annual recharge to the Rush Valley groundwater basin is estimated to be about 39,000 acre-feet. Nearly all recharge occurs as direct infiltration of snowmelt and rainfall within the mountains with smaller amounts occurring as infiltration of streamflow and unconsumed irrigation water at or near the mountain front. Groundwater generally flows from the higher altitude recharge areas toward two distinct valley-bottom discharge areas: one in the vicinity of Rush Lake in northern Rush Valley and the other located west and north of Vernon. Average annual discharge from the Rush Valley groundwater basin is estimated to be about 43,000 acre-feet. Most discharge occurs as evapotranspiration in the valley lowlands, as discharge to springs and streams, and as withdrawal from wells. Subsurface discharge outflow to Tooele and Cedar Valleys makes up only a small fraction of natural discharge. Groundwater samples were collected from 25 sites (24 wells and one spring) for geochemical analysis. Dissolved-solids concentrations in water from these sites ranged from 181 to 1,590 milligrams per liter. Samples from seven wells contained arsenic concentrations that exceed the Environmental Protection Agency Maximum Contaminant Level of 10 micrograms per liter. The highest arsenic levels are found north of Vernon and in southeastern Rush Valley. Stable-isotope ratios of oxygen and deuterium, along with dissolved-gas recharge temperatures, indicate that nearly all modern groundwater is meteoric and derived from the infiltration of high altitude precipitation in the mountains. These data are consistent with recharge estimates made using a Basin Characterization Model of net infiltration that shows nearly all recharge occurring as infiltration of precipitation and snowmelt within the mountains surrounding Rush Valley. Tritium concentrations between 0.4 and 10 tritium units indicate the presence of modern (less than 60 years old) groundwater at 7 of the 25 sample sites. Apparent 3 H/ 3 He ages, calculated for six of these sites, range from 3 to 35 years. Adjusted minimum radiocarbon ages of premodern water samples range from about 1,600 to 42,000 years with samples from 11 of 13 sites being more than 11,000 years. These data help to identify areas where modern groundwater is circulating through the hydrologic system on time scales of decades or less and indicate that large parts of the principal basin-fill and the bedrock aquifers are much less active and receive little to no modern recharge.

Utah↗
USGS2007

Use of sinkhole and specific capacity distributions to assess vertical gradients in a karst aquifer

The carbonate-rock aquifer in the Great Valley, West Virginia, USA, was evaluated using a database of 687 sinkholes and 350 specific capacity tests to assess structural, lithologic, and topographic influences on the groundwater flow system. The enhanced permeability of the aquifer is characterized in part by the many sinkholes, springs, and solutionally enlarged fractures throughout the valley. Yet, vertical components of subsurface flow in this highly heterogeneous aquifer are currently not well understood. To address this problem, this study examines the apparent relation between geologic features of the aquifer and two spatial indices of enhanced permeability attributed to aquifer karstification: (1) the distribution of sinkholes and (2) the occurrence of wells with relatively high specific capacity. Statistical results indicate that sinkholes (funnel and collapse) occur primarily along cleavage and bedding planes parallel to subparallel to strike where lateral or downward vertical gradients are highest. Conversely, high specific capacity values are common along prominent joints perpendicular or oblique to strike. The similarity of the latter distribution to that of springs suggests these fractures are areas of upward-convergent flow. These differences between sinkhole and high specific capacity distributions suggest vertical flow components are primarily controlled by the orientation of geologic structure and associated subsurface fracturing. ?? 2007 Springer-Verlag.

Environmental Geology↗
USGS2011

Documentation for the State Variables Package for the Groundwater-Management Process of MODFLOW-2005 (GWM-2005)

Many groundwater-management problems are concerned with the control of one or more variables that reflect the state of a groundwater-flow system or a coupled groundwater/surface-water system. These system state variables include the distribution of heads within an aquifer, streamflow rates within a hydraulically connected stream, and flow rates into or out of aquifer storage. This report documents the new State Variables Package for the Groundwater-Management Process of MODFLOW-2005 (GWM-2005). The new package provides a means to explicitly represent heads, streamflows, and changes in aquifer storage as state variables in a GWM-2005 simulation. The availability of these state variables makes it possible to include system state in the objective function and enhances existing capabilities for constructing constraint sets for a groundwater-management formulation. The new package can be used to address groundwater-management problems such as the determination of withdrawal strategies that meet water-supply demands while simultaneously maximizing heads or streamflows, or minimizing changes in aquifer storage. Four sample problems are provided to demonstrate use of the new package for typical groundwater-management applications.

Techniques and Methods↗
USGS2019

Groundwater salinity and the effects of produced water disposal in the Lost Hills-Belridge oilfields, Kern County, California

Increased oil and gas production in many areas has led to concerns over the effects these activities may be having on nearby groundwater quality. In this study we determine the lateral and vertical extent of groundwater with less than 10,000 milligrams per liter (mg/l) total dissolved solids (TDS) near the Lost Hills-Belridge oilfields in northwestern Kern County, California and document evidence of impacts by produced water disposal within the Tulare aquifer and overlying alluvium—the primary protected aquifers in the area. The depth at which groundwater salinity surpasses 10,000 mg/l ranges from 150 m (500 ft [ft]) in the northwestern part of the study area to 490 to 550 m (1,600-1,800 ft) in the south and east respectively as determined by geophysical log analysis and lab analysis of produced water samples. Comparison of logs from replacement wells with logs from their older counterparts shows relatively higher resistivity intervals representing the vadose zone or fresher groundwater being replaced by intervals with much lower resistivity due to infiltration of brines from surface disposal ponds and injection of brines into disposal wells. The effect of the surface ponds is confined to the alluvial aquifer—the underlying Tulare aquifer is largely protected by a regional clay layer at the base of the alluvium. Sand layers affected by injection of produced waters in nearby disposal wells often exhibit log resistivity profiles that change from high resistivity in their upper parts to low resistivity near the base due to stratification by gravity segregation of the denser brines within each affected sand. The effects of produced water injection are mainly evident within the Tulare Formation and can be noted as far as 550 m (1,800 ft) from the main group of disposal wells located along the east flank of South Belridge.

California↗
USGS2014

Modeling nitrate at domestic and public-supply well depths in the Central Valley, California

Aquifer vulnerability models were developed to map groundwater nitrate concentration at domestic and public-supply well depths in the Central Valley, California. We compared three modeling methods for ability to predict nitrate concentration >4 mg/L: logistic regression (LR), random forest classification (RFC), and random forest regression (RFR). All three models indicated processes of nitrogen fertilizer input at the land surface, transmission through coarse-textured, well-drained soils, and transport in the aquifer to the well screen. The total percent correct predictions were similar among the three models (69–82%), but RFR had greater sensitivity (84% for shallow wells and 51% for deep wells). The results suggest that RFR can better identify areas with high nitrate concentration but that LR and RFC may better describe bulk conditions in the aquifer. A unique aspect of the modeling approach was inclusion of outputs from previous, physically based hydrologic and textural models as predictor variables, which were important to the models. Vertical water fluxes in the aquifer and percent coarse material above the well screen were ranked moderately high-to-high in the RFR models, and the average vertical water flux during the irrigation season was highly significant (p < 0.0001) in logistic regression.

California↗
USGS2016

Analyses of infrequent (quasi-decadal) large groundwater recharge events in the northern Great Basin: Their importance for groundwater availability, use, and management

There has been a considerable amount of research linking climatic variability to hydrologic responses in the western United States. Although much effort has been spent to assess and predict changes in surface water resources, little has been done to understand how climatic events and changes affect groundwater resources. This study focuses on characterizing and quantifying the effects of large, multiyear, quasi-decadal groundwater recharge events in the northern Utah portion of the Great Basin for the period 1960–2013. Annual groundwater level data were analyzed with climatic data to characterize climatic conditions and frequency of these large recharge events. Using observed water-level changes and multivariate analysis, five large groundwater recharge events were identified with a frequency of about 11–13 years. These events were generally characterized as having above-average annual precipitation and snow water equivalent and below-average seasonal temperatures, especially during the spring (April through June). Existing groundwater flow models for several basins within the study area were used to quantify changes in groundwater storage from these events. Simulated groundwater storage increases per basin from a single recharge event ranged from about 115 to 205 Mm 3 . Extrapolating these amounts over the entire northern Great Basin indicates that a single large quasi-decadal recharge event could result in billions of cubic meters of groundwater storage. Understanding the role of these large quasi-decadal recharge events in replenishing aquifers and sustaining water supplies is crucial for long-term groundwater management.

Utah↗
USGS2014

Analysis of potential water-supply management options, 2010-60, and documentation of revisions to the model of the Irwin Basin Aquifer System, Fort Irwin National Training Center, California

The Fort Irwin National Training Center is considering several alternatives to manage their limited water-supply sources in the Irwin Basin. An existing three-dimensional, finite-difference groundwater-flow model—the U.S. Geological Survey’s MODFLOW—of the aquifer system in the basin was updated and the initial input dataset was supplemented with groundwater withdrawal data for the period 2000–10. The updated model was then used to simulate four combinations, or scenarios, of groundwater withdrawal and recharge over the next 50 years (January 2011 through December 2060). The scenarios included combinations of continuing withdrawals from currently active production wells, supplementing any increases in demand with withdrawals from an inactive production well, reducing withdrawal amounts and rates, and reducing the discharge of treated wastewater to infiltration ponds that provide a recharge source to the underlying aquifer. Results of the simulations indicated that, depending on the scenario implemented, groundwater levels would rise (over the next 50 years) from 40 feet to as much as 65 feet in the northwestern part of the Irwin Basin, and from 5 feet to 10 feet in the southeastern part.

California↗
USGS2014

Hydrogeologic framework and groundwater/surface-water interactions of the South Fork Nooksack River Basin, northwestern Washington

A hydrogeologic framework of the South Fork (SF) Nooksack River Basin in northwestern Washington was developed and hydrologic data were collected to characterize the groundwater-flow system and its interaction with surface‑water features. In addition to domestic, agricultural, and commercial uses of groundwater within the SF Nooksack River Basin, groundwater has the potential to provide ecological benefits by maintaining late-summer streamflows and buffering stream temperatures. Cold-water refugia, created and maintained in part by groundwater, have been identified by water-resource managers as key elements to restore the health and viability of threatened salmonids in the SF Nooksack River. The SF Nooksack River drains a 183-square mile area of the North Cascades and the Puget Lowland underlain by unconsolidated glacial and alluvial sediments deposited over older sedimentary, metamorphic, and igneous bedrock. The primary aquifer that interacts with the SF Nooksack River was mapped within unconsolidated glacial outwash and alluvial sediment. The lower extent of this unit is bounded by bedrock and fine-grained, poorly sorted unconsolidated glaciomarine and glaciolacustrine sediments. In places, these deposits overlie and confine an aquifer within older glacial sediments. The extent and thickness of the hydrogeologic units were assembled from mapped geologic units and lithostratigraphic logs of field-inventoried wells. Generalized groundwater-flow directions within the surficial aquifer were interpreted from groundwater levels measured in August 2012; and groundwater seepage gains and losses to the SF Nooksack River were calculated from synoptic streamflow measurements made in the SF Nooksack River and its tributaries in September 2012. A subset of the field-inventoried wells was measured at a monthly interval to determine seasonal fluctuations in groundwater levels during water year 2013. Taken together, these data provide the foundation for a future groundwater-flow model of the SF Nooksack River Basin that may be used to investigate the potential effects of future climate change, land use, and groundwater pumping on water resources in the study area. Site-specific hydrologic data, including time series of longitudinal temperature profiles measured with a fiber-optic distributed temperature sensor and continuous monitoring of stream stage and water levels measured in wells in adjacent wetlands and aquifers, also were measured to characterize the interaction among the SF Nooksack River, surficial aquifers, and riparian wetlands.

Washington↗