USGS Science⌕ Search

SEARCH · USGS Science

Results for “Energy”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82Linked to original sources
USGS2008

Comparison of two U.S. power-plant carbon dioxide emissions data sets

Estimates of fossil-fuel CO2 emissions are needed to address a variety of climate-change mitigation concerns over a broad range of spatial and temporal scales. We compared two data sets that report power-plant CO 2 emissions in the conterminous U.S. for 2004, the most recent year reported in both data sets. The data sets were obtained from the Department of Energy's Energy Information Administration (EIA) and the Environmental Protection Agency's eGRID database. Conterminous U.S. total emissions computed from the data sets differed by 3.5% for total plant emissions (electricity plus useful thermal output) and 2.3% for electricity generation only. These differences are well within previous estimates of uncertainty in annual U.S. fossil-fuel emissions. However, the corresponding average absolute differences between estimates of emissions from individual power plants were much larger, 16.9% and 25.3%, respectively. By statistical analysis, we identified several potential sources of differences between EIA and eGRID estimates for individual plants. Estimates that are based partly or entirely on monitoring of stack gases (reported by eGRID only) differed significantly from estimates based on fuel consumption (as reported by EIA). Differences in accounting methods appear to explain differences in estimates for emissions from electricity generation from combined heat and power plants, and for total and electricity generation emissions from plants that burn nonconventional fuels (e.g., biomass). Our analysis suggests the need for care in utilizing emissions data from individual power plants, and the need for transparency in documenting the accounting and monitoring methods used to estimate emissions.

Environmental Science & Technology↗
USGS1998

Partition characteristics of polycyclic aromatic hydrocarbons on soils and sediments

The partition behavior was determined for three polycyclic aromatic hydrocarbons (PAHs), i.e., naphthalene, phenanthrene, and pyrene, from water to a range of soil and sediment samples. The measured partition coefficients of the individual PAHs between soil/sediment organic matter (SOM) and water (i.e., K(oc) values) are relatively invariant either for the 'clean' (uncontaminated) soils or for the clean sediments; however, the mean K(oc) values on the sediments are about twice the values on the soils. This disparity is similar to the earlier observation for other nonpolar solutes and reflects the compositional differences between soil and sediment organic matters. No significant differences in K(oc) are observed between a clean coastal marine sediment and freshwater sediments. The coastal sediments that are significantly impacted by organic contaminants exhibit higher K(oc) values. At given K(ow) values (octanol-water), the PAHs exhibit much higher K(oc) values than other relatively nonpolar solutes (e.g., chlorinated hydrocarbons). This effect is shown to result from the enhanced partition of PAHs to SOM rather than from lower K(ow) values of PAHs at given supercooled liquid solute solubilities in water. The enhanced partition of PAHs over other nonpolar solutes in SOM provides an account of the markedly different correlations between log K(oc) and log K(ow) for PAHs and for other nonpolar solutes. The improved partition of PAHs in SOM stems apparently from the enhanced compatibility of their cohesive energy densities with those of the aromatic components in SOM. The approximate aromatic fraction in soil/sediment organic matter has been assessed by solid-state 13C-NMR spectroscopy.The partition behavior was determined for three polycyclic aromatic hydrocarbons (PAHs), i.e., naphthalene, phenanthrene, and pyrene, from water to a range of soil and sediment samples. The measured partition coefficients of the individual PAHs between soil/sediment organic matter (SOM) and water (i.e., Koc values) are relatively invariant either for the `clean' (uncontaminated) soils or for the clean sediments; however, the mean Koc values on the sediments are about twice the values on the soils. This disparity is similar to the earlier observation for other nonpolar solutes and reflects the compositional differences between soil and sediment organic matters. No significant differences in Koc are observed between a clean coastal marine sediment and freshwater sediments. The coastal sediments that are significantly impacted by organic contaminants exhibit higher Koc values. At given Kow values (octanol-water), the PAHs exhibit much higher Koc values than other relatively nonpolar solutes (e.g., chlorinated hydrocarbons). This effect is shown to result from the enhanced partition of PAHs to SOM rather than from lower Kow values of PAHs at given supercooled liquid solute solubilities in water. The enhanced partition of PAHs over other nonpolar solutes in SOM provides an account of the markedly different correlations between log Koc and log Kow for PAHs and for other nonpolar solutes. The improved partition of PAHs in SOM stems apparently from the enhanced compatibility of their cohesive energy densities with those of the aromatic components in SOM. The approximate aromatic fraction in soil/sediment organic matter has been assessed by solid-state 13C-NMR spectroscopy.

Environmental Science & Technology↗
USGS1998

Application of the surface complexation concept to complex mineral assemblages

Two types of modeling approaches are illustrated for describing inorganic contaminant adsorption in aqueous environments: (a) the component additivity approach and (b) the generalized composite approach. Each approach is applied to simulate Zn2+ adsorption by a well-characterized sediment collected from an aquifer at Cape Cod, MA. Zn2+ adsorption by the sediment was studied in laboratory batch experiments with a range of pH and Zn(II) concentrations selected to encompass conditions observed in the aquifer. In the generalized composite approach, one, and two-site surface complexation model parameters were calibrated with the experimental data using FITEQL. The pH dependence of Zn2+ adsorption was simulated without explicit representation of electrostatic energy terms. Surface acidity constants and ion pair formation by major electrolyte ions were also not required in the model thereby minimizing the number of fitted parameters. Predictions of Zn2+ adsorption with the component additivity modeling approach did not simulate the experimental data adequately without manipulation of surface area or site density parameter values. To apply the component additivity approach to environmental sorbents, further research is needed to better characterize the composition of sediment surface coatings. The generalized composite modeling approach requires less information and can be viewed as more practical for application within solute transport models. With only three adjustable parameters, this approach could simulate Zn2+ adsorption over a range of chemical conditions that would cause several orders of magnitude variation in the distribution coefficient (K(d)) for Zn2+ within the aquifer.Two types of modeling approaches are illustrated for describing inorganic contaminant adsorption in aqueous environments: (a) the component additivity approach and (b) the generalized composite approach. Each approach is applied to simulate Zn2+ adsorption by a well-characterized sediment collected from an aquifer at Cape Cod, MA. Zn2+ adsorption by the sediment was studied in laboratory batch experiments with a range of pH and Zn(II) concentrations selected to encompass conditions observed in the aquifer. In the generalized composite approach, one- and two-site surface complexation model parameters were calibrated with the experimental data using FITEQL. The pH dependence of Zn2+ adsorption was simulated without explicit representation of electrostatic energy terms. Surface acidity constants and ion pair formation by major electrolyte ions were also not required in the model, thereby minimizing the number of fitted parameters. Predictions of Zn2+ adsorption with the component additivity modeling approach did not simulate the experimental data adequately without manipulation of surface area or site density parameter values. To apply the component additivity approach to environmental sorbents, further research is needed to better characterize the composition of sediment surface coatings. The generalized composite modeling approach requires less information and can be viewed as more practical for application within solute transport models. With only three adjustable parameters, this approach could simulate Zn2+ adsorption over a range of chemical conditions that would cause several orders of magnitude variation in the distribution coefficient (Kd) for Zn2+ within the aquifer.

Environmental Science & Technology↗
USGS2014

Methane hydrates in nature - Current knowledge and challenges

Recognizing the importance of methane hydrate research and the need for a coordinated effort, the United States Congress enacted the Methane Hydrate Research and Development Act of 2000. At the same time, the Ministry of International Trade and Industry in Japan launched a research program to develop plans for a methane hydrate exploratory drilling project in the Nankai Trough. India, China, the Republic of Korea, and other nations also have established large methane hydrate research and development programs. Government-funded scientific research drilling expeditions and production test studies have provided a wealth of information on the occurrence of methane hydrates in nature. Numerous studies have shown that the amount of gas stored as methane hydrates in the world may exceed the volume of known organic carbon sources. However, methane hydrates represent both a scientific and technical challenge, and much remains to be learned about their characteristics and occurrence in nature. Methane hydrate research in recent years has mostly focused on: (1) documenting the geologic parameters that control the occurrence and stability of methane hydrates in nature, (2) assessing the volume of natural gas stored within various methane hydrate accumulations, (3) analyzing the production response and characteristics of methane hydrates, (4) identifying and predicting natural and induced environmental and climate impacts of natural methane hydrates, (5) analyzing the methane hydrate role as a geohazard, (6) establishing the means to detect and characterize methane hydrate accumulations using geologic and geophysical data, and (7) establishing the thermodynamic phase equilibrium properties of methane hydrates as a function of temperature, pressure, and gas composition. The U.S. Department of Energy (DOE) and the Consortium for Ocean Leadership (COL) combined their efforts in 2012 to assess the contributions that scientific drilling has made and could continue to make to advance our understanding of methane hydrates in nature. COL assembled a Methane Hydrate Project Science Team with members from academia, industry, and government. This Science Team worked with COL and DOE to develop and host the Methane Hydrate Community Workshop, which surveyed a substantial cross section of the methane hydrate research community for input on the most important research developments in our understanding of methane hydrates in nature and their potential role as an energy resource, a geohazard, and/or as an agent of global climate change. Our understanding of how methane hydrates occur in nature is still growing and evolving, and it is known with certainty that field, laboratory, and modeling studies have contributed greatly to our understanding of hydrates in nature and will continue to be a critical source of the information needed to advance our understanding of methane hydrates.

Journal of Chemical and Engineering Data↗
USGS1997

Vertical accretion and shallow subsidence in a mangrove forest of southwestern Florida, U.S.A

Simultaneous measurements of vertical accretion from artificial soil marker horizons and soil elevation change from sedimentation-erosion table (SET) plots were used to evaluate the processes related to soil building in range, basin, and overwash mangrove forests located in a low-energy lagoon which recieves minor inputs of terregenous sediments. Vertical accretion measures reflect the contribution of surficial sedimentation (sediment deposition and surface root growth). Measures of elevation change reflect not only the contributions of vertical accretion but also those of subsurface processes such as compaction, decomposition and shrink-swell. The two measures were used to calculate amounts of shallow subsidence (accretion minus elevation change) in each mangrove forest. The three forest types represent different accretionary envrionments. The basin forest was located behind a natural berm. Hydroperiod here was controlled primarily by rainfall rather than tidal exchange, although the basin flooded during extreme tidal events. Soil accretion here occurred primarily by autochthonous organic matter inputs, and elevation was controlled by accretion and shrink-swell of the substrate apparently related to cycles of flooding-drying and/or root growth-decomposition. This hydrologically-restricted forest did not experience an accretion or elevation deficit relative to sea-level rise. The tidally dominated fringe and overwash island forests accreted through mineral sediment inputs bound in place by plant roots. Filamentous turf algae played an important role in stabilizing loose muds in the fringe forest where erosion was prevalent. Elevation in these high-energy environments was controlled not only by accretion but also by erosion and/or shallow subsidence. The rate of shallow subsidence was consistently 3-4 mm y-1 in the fringe and overwash island forests but was negligible in the basin forest. Hence, the vertical development of mangrove soils was influenced by both surface and subsurface processes and the procces controlling soil elevation differed among forest types. The mangrove ecosystem at Rookery Bay has remained stable as sea level has risen during the past 70 years. Yet, lead-210 accretion data suggest a substantial accretion deficit has occurred in the past century (accretion was 10-20 cm < sea-level rise from 1930 to 1990) in the fringe and island forests at Rookery Bay. In contrast, our measures of elevation change mostly equalled the estimates of sea-level rise and shallow subsidence. These data suggest that (1) vertical accretion in this system is driven by local sea-level rise and shallow subsidence, and (2) the mangrove forests are mostly keeping pace with sea-level rise. Thus, the vulnerability of this mangrove ecosystem to sea-level rise is best described in terms of an elevation deficit (elevation change minus sea-level rise) based on annual measures rather than an accretion deficit (accretion minus sea-level rise) based on decadal measures.

Mangroves and Salt Marshes↗
USGS1997

The rupture process of the Manjil, Iran earthquake of 20 June 1990 and implications for intraplate strike-slip earthquakes

In terms of seismically radiated energy or moment release, the earthquake of 20 January 1990 in the Manjil Basin-Alborz Mountain region of Iran is the second largest strike-slip earthquake to have occurred in an intracontinental setting in the past decade. It caused enormous loss of life and the virtual destruction of several cities. Despite a very large meizoseismal area, the identification of the causative faults has been hampered by the lack of reliable earthquake locations and conflicting field reports of surface displacement. Using broadband data from global networks of digitally recording seismographs, we analyse broadband seismic waveforms to derive characteristics of the rupture process. Complexities in waveforms generated by the earthquake indicate that the main shock consisted of a tiny precursory subevent followed in the next 20 seconds by a series of four major subevents with depths ranging from 10 to 15 km. The focal mechanisms of the major subevents, which are predominantly strike-slip, have a common nodal plane striking about 285°–295°. Based on the coincidence of this strike with the dominant tectonic fabric of the region we presume that the EW striking planes are the fault planes. The first major subevent nucleated slightly south of the initial precursor. The second subevent occurred northwest of the initial precursor. The last two subevents moved progressively southeastward of the first subevent in a direction collinear with the predominant strike of the fault planes. The offsets in the relative locations and the temporal delays of the rupture subevents indicate heterogeneous distribution of fracture strength and the involvement of multiple faults. The spatial distribution of teleseismic aftershocks, which at first appears uncorrelated with meizoseismal contours, can be decomposed into stages. The initial activity, being within and on the periphery of the rupture zone, correlates in shape and length with meizoseismal lines. In the second stage of activity the aftershock zone expands and appears to cluster about the geomorphic and geologic features several tens of kilometres from the rupture zone. The activity is interpreted as a regional response to quasistatic stress migration along zones of tectonic weakness. The radiated energy of the main shock and the estimate of seismic moment yields an apparent stress of 20 bars. High apparent stress may be typical of strike slip earthquakes occurring in intracontinental environments undergoing continental collision.

Studia Geophysica et Geodaetica↗
USGS1999

Formation of natural gas hydrates in marine sediments 1. Conceptual model of gas hydrate growth conditioned by host sediment properties

The stability of submarine gas hydrates is largely dictated by pressure and temperature, gas composition, and pore water salinity. However, the physical properties and surface chemistry of deep marine sediments may also affect the thermodynamic state, growth kinetics, spatial distributions, and growth forms of clathrates. Our conceptual model presumes that gas hydrate behaves in a way analogous to ice in a freezing soil. Hydrate growth is inhibited within fine-grained sediments by a combination of reduced pore water activity in the vicinity of hydrophilic mineral surfaces, and the excess internal energy of small crystals confined in pores. The excess energy can be thought of as a "capillary pressure" in the hydrate crystal, related to the pore size distribution and the state of stress in the sediment framework. The base of gas hydrate stability in a sequence of fine sediments is predicted by our model to occur at a lower temperature (nearer to the seabed) than would be calculated from bulk thermodynamic equilibrium. Capillary effects or a build up of salt in the system can expand the phase boundary between hydrate and free gas into a divariant field extending over a finite depth range dictated by total methane content and pore-size distribution. Hysteresis between the temperatures of crystallization and dissociation of the clathrate is also predicted. Growth forms commonly observed in hydrate samples recovered from marine sediments (nodules, and lenses in muds; cements in sands) can largely be explained by capillary effects, but kinetics of nucleation and growth are also important. The formation of concentrated gas hydrates in a partially closed system with respect to material transport, or where gas can flush through the system, may lead to water depletion in the host sediment. This "freeze-drying" may be detectable through physical changes to the sediment (low water content and overconsolidation) and/or chemical anomalies in the pore waters and metastable presence of free gas within the normal zone of hydrate stability.

Journal of Geophysical Research B: Solid Earth↗
USGS2000

Preface [to special section on recent Loch Vale Watershed research]

Catchment-scale intensive and extensive research conducted over the last decade shows that our understanding of the biogeochemical and hydrologic processes in subalpine and alpine basins is not yet sufficiently mature to model and predict how biogeochemical transformations and surface water quality will change in response to climatic or human-driven changes in energy, water, and chemicals. A better understanding of these processes is needed for input to decision-making regulatory agencies and federal land managers. In recognition of this problem the National Research Council [1998] has identified as a critical research need an improved understanding of how global change will affect biogeochemical interactions with the hydrologic cycle and biogeochemical controls over the transport of water, nutrients, and materials from land to freshwater ecosystems. Improved knowledge of alpine and subalpine ecosystems is particularly important since high-elevation catchments are very sensitive to small changes in the flux of energy, chemicals, and water. Furthermore, alpine ecosystems may act as early warning indicators for ecosystem changes at lower elevations.

Colorado↗
USGS2000

Fracture process zone in granite

In uniaxial compression tests performed on Aue granite cores (diameter 50 mm, length 100 mm), a steel loading plate was used to induce the formation of a discrete shear fracture. A zone of distributed microcracks surrounds the tip of the propagating fracture. This process zone is imaged by locating acoustic emission events using 12 piezoceramic sensors attached to the samples. Propagation velocity of the process zone is varied by using the rate of acoustic emissions to control the applied axial force. The resulting velocities range from 2 mm/s in displacement-controlled tests to 2 μm/s in tests controlled by acoustic emission rate. Wave velocities and amplitudes are monitored during fault formation. P waves transmitted through the approaching process zone show a drop in amplitude of 26 dB, and ultrasonic velocities are reduced by 10%. The width of the process zone is ∼9 times the grain diameter inferred from acoustic data but is only 2 times the grain size from optical crack inspection. The process zone of fast propagating fractures is wider than for slow ones. The density of microcracks and acoustic emissions increases approaching the main fracture. Shear displacement scales linearly with fracture length. Fault plane solutions from acoustic events show similar orientation of nodal planes on both sides of the shear fracture. The ratio of the process zone width to the fault length in Aue granite ranges from 0.01 to 0.1 inferred from crack data and acoustic emissions, respectively. The fracture surface energy is estimated from microstructure analysis to be ∼2 J. A lower bound estimate for the energy dissipated by acoustic events is 0.1 J.

Journal of Geophysical Research B: Solid Earth↗
USGS2000

A compartmentalized solute transport model for redox zones in contaminated aquifers: 1. Theory and development

This paper, the first of two parts [see Abrams and Loague , this issue], takes the compartmentalized approach for the geochemical evolution of redox zones presented by Abrams et al . [1998] and embeds it within a solute transport framework. In this paper the compartmentalized approach is generalized to facilitate the description of its incorporation into a solute transport simulator. An equivalent formulation is developed which removes any discontinuities that may occur when switching compartments. Rate‐limited redox reactions are modeled with a modified Monod relationship that allows either the organic substrate or the electron acceptor to be the rate‐limiting reactant. Thermodynamic constraints are used to inhibit lower‐energy redox reactions from occurring under infeasible geochemical conditions without imposing equilibrium on the lower‐energy reactions. The procedure used allows any redox reaction to be simulated as being kinetically limited or thermodynamically limited, depending on local geochemical conditions. Empirical reaction inhibition methods are not needed. The sequential iteration approach (SIA), a technique which allows the number of solute transport equations to be reduced, is adopted to solve the coupled geochemical/solute transport problem. When the compartmentalized approach is embedded within the SIA, with the total analytical concentration of each component as the dependent variable in the transport equation, it is possible to reduce the number of transport equations even further than with the unmodified SIA. A one‐dimensional, coupled geochemical/solute transport simulation is presented in which redox zones evolve dynamically in time and space. The compartmentalized solute transport (COMPTRAN) model described in this paper enables the development of redox zones to be simulated under both kinetic and thermodynamic constraints. The modular design of COMPTRAN facilitates the use of many different, preexisting solute transport and geochemical codes. The companion paper [ Abrams and Loague , this issue] presents examples of the application of COMPTRAN to field‐scale problems.

Water Resources Research↗
USGS2001

Stress drop with constant, scale independent seismic efficiency and overshoot

To model dissipated and radiated energy during earthquake stress drop, I calculate dynamic fault slip using a single degree of freedom spring-slider block and a laboratory-based static/kinetic fault strength relation with a dynamic stress drop proportional to effective normal stress. The model is scaled to earthquake size assuming a circular rupture; stiffness varies inversely with rupture radius, and rupture duration is proportional to radius. Calculated seismic efficiency, the ratio of radiated to total energy expended during stress drop, is in good agreement with laboratory and field observations. Predicted overshoot, a measure of how much the static stress drop exceeds the dynamic stress drop, is higher than previously published laboratory and seismic observations and fully elasto-dynamic calculations. Seismic efficiency and overshoot are constant, independent of normal stress and scale. Calculated variation of apparent stress with seismic moment resembles the observational constraints of McGarr [1999].

Geophysical Research Letters↗
USGS2001

Moss and lichen cover mapping at local and regional scales in the boreal forest ecosystem of central Canada

Mosses and lichens are important components of boreal landscapes [Vitt et al., 1994; Bubier et al., 1997]. They affect plant productivity and belowground carbon sequestration and alter the surface runoff and energy balance. We report the use of multiresolution satellite data to map moss and lichens over the BOREAS region at a 10 m, 30 m, and 1 km scales. Our moss and lichen classification at the 10 m scale is based on ground observations of associations among soil drainage classes, overstory composition, and cover type among four broad classes of ground cover (feather, sphagnum, and brown mosses and lichens). For our 30 m map, we used field observations of ground cover-overstory associations to map mosses and lichens in the BOREAS southern study area (SSA). To scale up to a 1 km (AVHRR) moss map of the BOREAS region, we used the TM SSA mosaics plus regional field data to identify AVHRR overstory-ground cover associations. We found that: 1) ground cover, overstory composition and density are highly correlated, permitting inference of moss and lichen cover from satellite-based land cover classifications; 2) our 1 km moss map reveals that mosses dominate the boreal landscape of central Canada, thereby a significant factor for water, energy, and carbon modeling; 3) TM and AVHRR moss cover maps are comparable; 4) satellite data resolution is important; particularly in detecting the smaller wetland features, lakes, and upland jack pine sites; and 5) distinct regional patterns of moss and lichen cover correspond to latitudinal and elevational gradients. Copyright 2001 by the American Geophysical Union.

Journal of Geophysical Research D: Atmospheres↗
USGS2004

Crystallographic controls on the frictional behavior of dry and water-saturated sheet structure minerals

We compare the frictional strengths of 17 sheet structure mineral powders, measured under dry and water-saturated conditions, to identify the factors that cause many of them to be relatively weak. The dry coefficient of friction μ ranges upward from 0.2 for graphite, leveling off at 0.8 for margarite, clintonite, gibbsite, kaolinite, and lizardite. The values of μ (dry) correlate directly with calculated (001) interlayer bond strengths of the minerals. This correlation occurs because shear becomes localized along boundary and Riedel shears and the platy minerals in them rotate into alignment with the shear planes. For those gouges with μ (dry) < 0.8, shear occurs by breaking the interlayer bonds to form new cleavage surfaces. Where μ (dry) = 0.8, consistent with Byerlee's law, the interlayer bonds are sufficiently strong that other frictional processes dominate. The transition in dry friction mechanisms corresponds to calculated surface energies of 2–3 J/m 2 . Adding water causes μ to decrease for every mineral tested except graphite. If the minerals are separated into groups with similar crystal structures, μ (wet) increases with increasing interlayer bond strength within each group. This relationship also holds for the swelling clay montmorillonite, whose water-saturated strength is consistent with the strengths of nonswelling clays of similar crystal structure. Water in the saturated gouges forms thin, structured films between the plate surfaces. The polar water molecules are bonded to the plate surfaces in proportion to the mineral's surface energy, and μ (wet) reflects the stresses required to shear through the water films.

Journal of Geophysical Research B: Solid Earth↗
USGS2011

International heat flow commission celebrates 40 years

The outflow of heat from the Earth's interior is, in terms of energy, the most impressive terrestrial phenomenon. Its present rate of about 1021 joules per year is order‐of‐magnitudes greater than the energy dissipation of earthquakes or heat loss from volcanic eruptions. The study of the Earth's internal heat plays an important role in understanding the Earth's origin, internal constitution, and plate tectonics. The thermal structure of the Earth, generally referred to as the geothermics, or also as the (terrestrial) heat flow, has been studied for a long time. However, modern geothermics, one of the fundamental geophysical disciplines, is relatively young. The International Heat Flow Commission (IHFC), under which the academic geothermal research on the international scale is organized, was created only in 1963. The IHFC, operating under the International Association of Seismology and Physics of the Earth's Interior (IASPEI), covers a broad scope of geophysical studies, and links the activities of other associations of the International Union of Geodesy and Geophysics (IUGG).

Eos, Earth and Space Science News↗
USGS2004

Application of near real-time radial semblance to locate the shallow magmatic conduit at Kilauea Volcano, Hawaii

Radial Semblance is applied to broadband seismic network data to provide source locations of Very-Long-Period (VLP) seismic energy in near real time. With an efficient algorithm and adequate network coverage, accurate source locations of VLP energy are derived to quickly locate the shallow magmatic conduit system at Kilauea Volcano, Hawaii. During a restart in magma flow following a brief pause in the current eruption, the shallow magmatic conduit is pressurized, resulting in elastic radiation from various parts of the conduit system. A steeply dipping distribution of VLP hypocenters outlines a region extending from sea level to about 550 m elevation below and just east of the Halemaumau Pit Crater. The distinct hypocenters suggest the shallow plumbing system beneath Halemaumau consists of a complex plexus of sills and dikes. An unconstrained location for a section of the conduit is also observed beneath the region between Kilauea Caldera and Kilauea Iki Crater.

Hawaii↗
USGS2005

Nearshore wave-induced cyclical flexing of sea cliffs

[1] Evolution of a tectonically active coast is driven by geomorphically destructive energy supplied by ocean waves. Wave energy is episodic and concentrated; sea cliffs are battered by the geomorphic wrecking ball every 4-25 s. We measure the response of sea cliffs to wave assault by sensing the ground motion using near-coastal seismometers. Sea cliffs respond to waves in two distinct styles. High-frequency motion (20 Hz) reflects the natural frequency of the sea cliff as it rings in response to direct wave impact. Low-frequency motion in the 0.1-0.05 Hz (10-20 s) band consistently agrees with the dominant nearshore wave period. Integrating microseismic velocities suggests 50 ??m and 10 ??m displacements in horizontal and vertical directions, respectively. Displacement ellipsoids exhibit simultaneous downward and seaward sea cliff motion with each wave. Video footage corroborates the downward sea cliff flex in response to the imposed water load on the wave cut platform. Gradients in displacement amplitudes documented using multiple seismometers suggest longitudinal and shear strain of the flexing sea cliff on the order of 0.5-4 ?? strains during each wave loading cycle. As this sea cliff flexure occurs approximately 3 million times annually, it has the potential to fatigue the rock through cyclical loading. Local sea cliff retreat rates of 10 cm/yr imply that a given parcel of rock is flexed through roughly 109 cycles of increasing amplitude before exposure to direct wave attack at the cliff face. Copyright 2005 by the American Geophysical Union.

Journal of Geophysical Research F: Earth Surface↗
USGS2006

Surface drifter derived circulation in the northern and middle Adriatic Sea: Response to wind regime and season

More than 120 satellite-tracked drifters were deployed in the northern and middle Adriatic (NMA) Sea between September 2002 and November 2003, with the purpose of studying the surface circulation at mesoscale to seasonal scale in relation to wind forcing, river runoff, and bottom topography. Pseudo-Eulerian and Lagrangian statistics were calculated from the low-pass-filtered drifter velocity data between September 2002 and December 2003. The structure of the mean circulation is determined with unprecedented high horizontal resolution by the new data. In particular, mean currents, velocity variance, and kinetic energy levels are shown to be maximal in the Western Adriatic Current (WAC). Separating data into seasons, we found that the mean kinetic energy is maximal in fall, with high values also in winter, while it is significantly weaker in summer. High-resolution Local Area Model Italy winds were used to relate the drifter velocities to the wind fields. The surface currents appear to be significantly influenced by the winds. The mean flow during the northeasterly bora regime shows an intensification of the across-basin recirculating currents. In addition, the WAC is strongly intensified both in intensity and in its offshore lateral extension. In the southeasterly sirocco regime, northward flow without recirculation dominates in the eastern half of the basin, while during northwesterly maestro the WAC is enhanced. Separating the data into low and high Po River discharge rates for low-wind conditions shows that the WAC and the velocity fluctuations in front of the Po delta are stronger for high Po River runoff. Lagrangian covariance, diffusivity, and integral time and space scales are larger in the along-basin direction and are maximal in the southern portion of the WAC. Copyright 2006 by the American Geophysical Union.

Journal of Geophysical Research C: Oceans↗
USGS2006

Mountain hydrology of the western United States

Climate change and climate variability, population growth, and land use change drive the need for new hydrologic knowledge and understanding. In the mountainous West and other similar areas worldwide, three pressing hydrologic needs stand out: first, to better understand the processes controlling the partitioning of energy and water fluxes within and out from these systems; second, to better understand feedbacks between hydrological fluxes and biogeochemical and ecological processes; and, third, to enhance our physical and empirical understanding with integrated measurement strategies and information systems. We envision an integrative approach to monitoring, modeling, and sensing the mountain environment that will improve understanding and prediction of hydrologic fluxes and processes. Here extensive monitoring of energy fluxes and hydrologic states are needed to supplement existing measurements, which are largely limited to streamflow and snow water equivalent. Ground‐based observing systems must be explicitly designed for integration with remotely sensed data and for scaling up to basins and whole ranges.

Water Resources Research↗