USGS Science⌕ Search

SEARCH · USGS Science

Results for “Marine Geology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69Linked to original sources
USGS1993

Map showing sediment isopachs in the deep-sea basins of the Pacific Continental Margin, Strait of Juan de Fuca to Cape Mendocino

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1993

Map showing depth to basement in the deep-sea basins of the Pacific continental margin, Strait of Juan de Fuca to Cape Mendocino

The U.S. Geological Survey conducted a series of cruises, EEZSCAN 84 (EEZ-SCAN 84 Scientific Staff, 1986), to collect reconnaissance data on the newly proclaimed Exclusive Economic Zone (EEZ), the area out to 200 nautical miles from the coastline of the United States. The cruises systematically surveyed the entire conterminous United States west coast EEZ using the Geological Long-Range Inclined Asdic (GLORIA) side-scan sonar, a 160-in 3 airgun seismic-reflection profiler, a 3.5-kHz high-resolution seismic-reflection profiler, a 10-kHz echo sounder, and a proton-precession magnetometer. The nominal trackline spacing throughout the survey was 30 km. Derivative maps of sediment thickness (I-2089-A, I-2090-A, I-2091-A) and depth to basement (I-2089-B, I-2090-B, I-2091-B) in the basins of the west coast EEZ were compiled from both the sonar-image dala and the deep-penetration seismic data obtained on these cruises. Only EEZ-SCAN 84 data were used for the map compilations because available data from other cruises in this region are sparsely located, have poor navigational control, or were obtained with seismic systems that were not powerful enough to resolve oceanic basement. For this map series, sediment thickness and depth to basement were determined only in the deep-ocean basin regions because the seismic system used on the EEZ-SCAN 84 cruises could not resolve oceanic basement beneath the thick sediments of the continental slope. All the data used to compile the maps are presented in the "Atlas of the Exclusive Economic Zone, Western Conterminous United States" (EEZ-SCAN 84 Scientific Staff, 1986). Basement Outcrops GLORIA imagery was used to locate areas of basement outcrop throughout the region. Where possible, sediment thickness on and immediately adjacent to basement outcrops was measured from seismic data. Where there was no bathymetric or seismic control, a seamount peak was assumed to have no sediment cover. A pattern is used on the map to indicate all basement outcrops. Data Reduction Acoustic basement in the basins, invariably oceanic Layer 2, was observed on all of the seismic records. One-way traveltime was measured from the sea floor to acoustic basement. Because the trackline spacing of about 30 km is relatively large compared to the data density along track, we chose to measure the sediment thickness every 0.5 hour or at an interval of approximately 7.5 km. Water depth was measured with a 10-kHz profiler. Depth to basement was calculated using the sea surface as the zero datum and adding the corrected water depth (Carter, 1980) to the sediment thickness. Acoustic travel times were converted to depths by first calculating a regression equation from the interval velocity versus depth data of Connard and others (1984). Their data base comprises a compilation of all available Deep Sea Drilling Project data plus wide-angle refraction data, which were collected in Cascadia Basin west of Oregon and represents the best data set available for the United States west coast EEZ. The regression equation was integrated to determine sediment thickness as a function of one-way traveltime . The resulting equation is z = 1400t + 0 .5t 2 where z is sediment thickness in meters, and t is one-way traveltime in seconds. Sediment thicknesses calculated using this equation were compared to values calculated from the general equation of Carlson and others (1986). Values for sediment thickness calculated by the two equations differed by no greater than 10 percent throughout the range of travel times. Bathymetry The bathymetry is from Chase and others (1981). The bathymetric data were compiled from a variety of sources, and data quality is inconsistent. Because of differences in navigational precision and density of coverage, the bathymetric contours of a feature may be at a different location than the corresponding isopleths derived from the EEZ-SCAN 84 data, or a feature may not be indicated on the bathymetry at all. These situations occur because either the feature is poorly located in the bathymetric data set or, especially in the outer EEZ, the bathymetric data are too sparse to have defined the existence of a feature. Acknowledgments Topographic digital data bases were corrected and verified by Christina Lief. Gerald Evenden developed the computer software system MAPGEN, used to compose this map. Reviews, suggestions, and technical contributions from Edward C. Escowitz and Florence Wong and advice about cartographic design from Will Stettner substantially improved the quality of this map. References Cited Carlson, R.L., Gangi, A.F., and Snow, K.R., 1986, Empirical reflection-traveltime/ depth and velocity/depth functions for the deep-sea sediment column: Journal of Geophysical Research, v. 91, no. B8, p. 8249-8266. Carter, D.J.T., 1980, Echo-sounding correction tables: Taunton, United Kingdom, Hydrographic Department, Ministry of Defence, 150 p. Chase, T.E., Wilde, Pat, Normark, W.R, Miller, C.P., Seekins, B.A., and Young, J.D., 1981, Offshore topography of the Western United States between 32° and 49° North latitudes: U.S. Geological Survey Open-File Report 81-443, scale 1:864,518 at 38° latitude, 2 sheets. Connard, G., Couch, R., Keeling , K., Roy, J., and Troseth, S., 1984, Abyssal plain and continental net-objective sedimentary thicknesses, in Kulm, L.D., and others, eds., Western North America continental margin and adjacent ocean floor off Oregon and Washington, Atlas 1 of Regional Atlas Series, Ocean Margin Drilling Program: Woods Hole, Mass., Marine Science International, sheet 7. EEZ-SCAN 84 Scientific Staff, 1986, Atlas of the Exclusive Economic Zone, Western Conterminous United States: U.S. Geological Survey Miscellaneous Investigations Series I-1792, scale 1:500,000, 152 p. See Also "U.S. Pacific West Coast Field Activities" (Paskevich and others, 2011; http://pubs.usgs.gov/of/2010/1332/htmldocs/pc/pc_overview.html). Paskevich, V.F., Wong, F.L., O?Malley, J.J., Stevenson, A.J., and Gutmacher, C.E., 2011, GLORIA sidescan-sonar imagery for parts of the U.S. Exclusive Economic Zone and adjacent areas: U.S. Geological Survey Open-File Report 2010?1332, available at http://pubs.usgs.gov/of/2010/1332/.

IMAP↗
USGS1958

The relation of phosphorites to ground water in Beaufort County, North Carolina

Recent ground-water studies undertaken by the U.S. Geological Survey in cooperation with the North Carolina Division of Mineral Resources have delineated phosphorite deposits, tentatively regarded as being of middle Miocene age, in Beaufort County. These deposits lie unconforma-bly on limestone of Eocene age and are unconformably overlain by late Miocene marl. The phosphorites, buried beneath strata ranging in thickness from 45 to 250 feet, underlie an area approximating 450 square miles. The total thickness of the phosphorite column throughout the area ranges from several feet to nearly 90 feet. The phosphorite column consists of phosphatic sands and intercalated shell limestones. The sands, composed of pellets of brown sand-size collophane (probably carbonate-fluorapatite) and sand-size, flat-sided angular quartz with some silt, clay, and organic material, have a median diameter between 0.50 and 0.25 mm. Chemical analyses of representative samples of the raw sand show a variation in PaOs content from 8 to 31 percent. The P2O5 content is apparently proportionate to the collophane content throughout the area. Reconstruction of the geologic history suggests that the phosphorites were deposited as chemical precipitates and as in situ replacements in a restricted marine basin where the pH of the water acted as the primary depositional control. Reconstruction of the hydrologic history of the phosphorites indicates that the deposits were preserved under artesian conditions; they were never subjected to alteration under water-table conditions. The absence of postpositional alteration makes this area a potentially classic one for studies of phosphorite genesis. Chemical analyses of artesian waters from the phosphorites and from limestones overlain by phosphorites reveal significantly greater concentrations of iodide and bromide in solution than are present in water from overlying sediments or from underlying limestones not overlain by phosphorites. Such anomalies, if present in other similar terranes, may indicate the presence of buried phosphorites. The depth and size distribution of the material suggest a recovery method utilizing wells constructed to "pump sand."

North Carolina↗
USGS2015

Geological sampling data and benthic biota classification: Buzzards Bay and Vineyard Sound, Massachusetts

Sea-floor sample collection is an important component of a statewide cooperative mapping effort between the U.S. Geological Survey (USGS) and the Massachusetts Office of Coastal Zone Management (CZM). Sediment grab samples, bottom photographs, and video transects were collected within Vineyard Sound and Buzzards Bay in 2010 aboard the research vessel Connecticut . This report contains sample data and related information, including analyses of surficial-sediment grab samples, locations and images of sea-floor photography, survey lines along which sea-floor video was collected, and a classification of benthic biota observed in sea-floor photographs and based on the Coastal and Marine Ecological Classification Standard (CMECS). These sample data and analyses information are used to verify interpretations of geophysical data and are an essential part of geologic maps of the sea floor. These data also provide a valuable inventory of benthic habitat and resources. Geographic information system (GIS) data, maps, and interpretations, produced through the USGS and CZM mapping cooperative, are intended to aid efforts to manage coastal and marine resources and to provide baseline information for research focused on coastal evolution and environmental change.

Massachusetts↗
USGS2016

Trace elements at the intersection of marine biological and geochemical evolution

Life requires a wide variety of bioessential trace elements to act as structural components and reactive centers in metalloenzymes. These requirements differ between organisms and have evolved over geological time, likely guided in some part by environmental conditions. Until recently, most of what was understood regarding trace element concentrations in the Precambrian oceans was inferred by extrapolation, geochemical modeling, and/or genomic studies. However, in the past decade, the increasing availability of trace element and isotopic data for sedimentary rocks of all ages has yielded new, and potentially more direct, insights into secular changes in seawater composition – and ultimately the evolution of the marine biosphere. Compiled records of many bioessential trace elements (including Ni, Mo, P, Zn, Co, Cr, Se, and I) provide new insight into how trace element abundance in Earth's ancient oceans may have been linked to biological evolution. Several of these trace elements display redox-sensitive behavior, while others are redox-sensitive but not bioessential (e.g., Cr, U). Their temporal trends in sedimentary archives provide useful constraints on changes in atmosphere-ocean redox conditions that are linked to biological evolution, for example, the activity of oxygen-producing, photosynthetic cyanobacteria. In this review, we summarize available Precambrian trace element proxy data, and discuss how temporal trends in the seawater concentrations of specific trace elements may be linked to the evolution of both simple and complex life. We also examine several biologically relevant and/or redox-sensitive trace elements that have yet to be fully examined in the sedimentary rock record (e.g., Cu, Cd, W) and suggest several directions for future studies.

Earth-Science Reviews↗
USGS2025

New evidence for eolian activity and mammoths on Santa Rosa Island prior to the Last Glacial Maximum

Sea-level fluctuations due to the growth and decay of continental ice sheets of the Quaternary exert a strong influence on geologic processes along coastlines. The California Channel Islands are no exception to this, and many studies have been conducted that focus on the extremes of these glacial-interglacial cycles, such as the last glacial period (marine isotope stage [MIS] 2) and the last interglacial period (MIS 5). Far less attention has been paid to intermediate time periods between these extremes, such as MIS 4. Here, we present two very different geologic records from this time period that show how sea-level change affected the nature of sedimentation on the northern shore of Santa Rosa Island. On the northwestern coast of Santa Rosa Island, thick eolian sediments accumulated between ~80 ka and ~45 ka due to a lowered sea level that exposed carbonate-rich skeletal sands that had accumulated during the last interglacial period. On the central part of the northern coast of Santa Rosa Island, thick alluvial sediments were deposited between 80 ka and 47 ka, similar to the time of eolian sedimentation to the west. A mammoth tusk discovered within these deposits is only the third stratigraphically controlled mammoth fossil on the Channel Islands that dates prior to MIS 2. Its discovery adds to the evidence that mammoths migrated to the Channel Islands from mainland California prior to the Last Glacial Maximum.

California↗
USGS1973

Atlas of Mars, Phoenicis Lacus quadrangle, MC-17

This mosaic is made with computer enhanced Mariner 9 pictures, rectified and scaled to a Mercator projection. Computer processing was performed by the Image Processing Laboratory (IPL) of the Jet Propulsion Laboratory (JPL). Processing included contrast enhancement and high-pass filtering which accentuates topographic features while subduing albedo variations. Photographic reproductions of the images were generated from the IPL digital magnetic tapes and mosaicked by the U.S. Geological Survey. Horizontal controls were derived from spacecraft tracking data, which are based on astronomical definitions of the spin axis and system of longitudes in use during the Mariner 9 mission. The projection is based on a theoretical dynamical ellipticity of 1/192. The scale is based on an equatorial radius of 3393.4 km. Standard deviation in image placement is less than 5 km at map scale.

Open-File Report↗
USGS2018

Science partnership between U.S. Geological Survey and the Lower Elwha Klallam Tribe—Understanding the Elwha River Dam Removal Project

After nearly a century of producing power, two large hydroelectric dams on the Elwha River in Washington State were removed during 2011 to 2014 to restore the river ecosystem and recover imperiled salmon populations. Roughly two-thirds of the 21 million cubic meters of sediment—enough to fill nearly 2 million dump trucks—contained behind the dams was released downstream, which restored natural processes and initiated important changes to the river, estuarine, and marine ecosystems. A multidisciplinary team of scientists from the Lower Elwha Klallam Tribe, academia, non-governmental organizations, Federal and state agencies, and the U.S. Geological Survey collected key data before, during, and after dam removal to understand the outcomes of this historic project on the Elwha River ecosystem.

Washington↗
USGS2002

Crustal structure of the coastal and marine San Francisco Bay region, California

As of the time of this writing, the San Francisco Bay region is home to about 6.8 million people, ranking fifth among population centers in the United States. Most of these people live on the coastal lands along San Francisco Bay, the Sacramento River delta, and the Pacific coast. The region straddles the tectonic boundary between the Pacific and North American Plates and is crossed by several strands of the San Andreas Fault system. These faults, which are stressed by about 4 cm of relative plate motion each year, pose an obvious seismic hazard. We have many ways to study earthquake faults. Where faults break the land surface, we may learn valuable information needed for hazard assessment, such as cumulative offset, slip rate, and earthquake history. However, many of the major faults in the region are partly submerged beneath San Francisco and Monterey Bays. Although this situation poses problems in gathering observational data for hazard assessment, bay-region waterways provide an opportunity to study faultzone structure by using marine subsurface-imaging techniques, which are easier and cheaper than equivalent studies on land. In 1993, the U.S. Geological Survey (USGS) launched a 5-year project aimed at unearthing the basic science of the submerged San Andreas strike-slip fault system in the San Francisco Bay region with its many interacting strands. Primary project goals were structural, such as to discover how the San Andreas and Hayward Faults are connected or related at depth, to learn how the complex of faults in the San Andreas stepover zone on the Golden Gate platform functions, and to locate previously unknown faults. This volume thus contains mostly structural information about the San Francisco Bay region, much of it gathered through exploratory geophysical experiments. The volume is organized “top down,” from studies in the shallowest crust to the base of the crust. The first three chapters are linked through their use of novel geophysical techniques to study earthquake effects, coseismic slip, and shallow stratigraphy. Kayen and others examine crustal structure at very high resolution and demonstrate the use of ground-penetrating-radar tomography to measure the liquefaction potential of coastal sedimentary deposits. McGann and others use microfossils from drill cores along the San Francisco-Oakland Bay Bridge to determine a more detailed late Pleistocene stratigraphy of San Francisco Bay than was previously available. Geist and Zoback use the historical record of a small local tsunami generated by the great 1906 San Francisco earthquake to model the rupture process of that earthquake. The last four chapters are dedicated to studies of fault related structure of the seismogenic crust in and around the San Andreas Fault system in the San Francisco Bay region. Jachens and others compile an aeromagnetic anomaly map from new high-resolution flights across the bay region. Some of these anomalies mark the positions of offshore faults, and others are offset by faults, providing constraints on cumulative slip. Hart and others concisely summarize the marine seismic data recorded in and around San Francisco Bay, map the coverage, and provide archival information for those interested in acquiring data. The last two chapters present the results of the seismic data that have been analyzed. Bruns and others present their analysis of high-quality intermediate-resolution (~5-km penetration) seismic-reflection data gathered over the complex San Andreas-San Gregorio Fault junction. This junction, which is thought to be where the 1906 San Francisco earthquake originated (see Geist and Zoback, this volume), contains an apparent extensional right stepover in the San Andreas Fault. Finally, Parsons and others review and summarize the results of deep-crustal seismic-reflection experiments and local-earthquake tomographic studies, including previously unpublished data, and provide additional support and discussion for already-published studies. In summary, these studies were carried out in an environment where background information on faults in the San Francisco Bay region was sought. Much of the structural information presented here comes from experiments of a style unlikely to be conducted by the USGS in the near future. Together, the chapters in this volume provide a structural framework for a major part of a complex strike-slip fault system.

California↗
USGS2001

Geologic Map of the MTM-85000 Quadrangle, Planum Australe Region of Mars

Introduction The polar deposits on Mars probably record martian climate history over the last 107 to 109 years (for example, Thomas and others, 1992). The area shown on this map includes layered polar deposits and residual polar ice, as well as some exposures of older terrain. Howard and others (1982) noted that an area (at lat 84.8 S., long 356 W.) near a 23-km diameter impact crater (Plaut and others, 1988) appears to have undergone recent deposition, as evidenced by the partial burial of secondary craters. Herkenhoff and Murray (1990a) mapped this area as a mixture of frost and defrosted ground and suggested that the presence of frost throughout the year stabilizes dust deposited in this area. This quadrangle was mapped using high-resolution Mariner 9 (table 1) and Viking Orbiter images in order to study the relations among erosional, cratering, and depositional processes on the polar layered deposits and to search for further evidence of recent deposition. Published geologic maps of the south polar region of Mars are based on images acquired by Mariner 9 (Condit and Soderblom, 1978; Scott and Carr, 1978) and the Viking Orbiters (Tanaka and Scott, 1987). The extent of the layered deposits mapped previously from Mariner 9 data is different from that mapped using Viking Orbiter images, and the present map agrees with the map by Tanaka and Scott (1987): the layered deposits extend to the northern boundary of the map area. However, the oldest unit in this area is mapped as undivided material (unit HNu) rather than the hilly unit in the plateau sequence (unit Nplh; Tanaka and Scott, 1987). The residual polar ice cap, areas of partial frost cover, the layered deposits, and two nonvolatile surface units-the dust mantle and the dark material-were mapped by Herkenhoff and Murray (1990a) at 1:2,000,000 scale using a color mosaic of Viking Orbiter images. This mosaic was used to confirm the identification of the non-volatile Amazonian units for this map and to test hypotheses for their origin and evolution. The colors and albedos of these units, as measured in places both within and outside of this map area, are presented in table 2 and figure 1. The red/violet ratio image was particularly useful in distinguishing the various low-albedo materials, as brightness variations due to topography are essentially removed in such ratio images and color variations are easily seen. Because the resolution of the color mosaics is not sufficient to map these units in detail at 1:500,000 scale, contacts between them were recognized and mapped using higher resolution black and white Viking and Mariner 9 images. The largest impact crater in the layered deposits, 23 km in diameter at lat 84.5 S., long 359 W., now named 'McMurdo,' was recognized by Plaut and others (1988). The northern rim of this crater is missing, perhaps due to erosion of the layered deposits in which it was formed (fig. 2). Secondary craters from this impact are not observed north of the crater but are abundant to the south. Although the crater statistics are poor (only 16 likely impact craters found in Viking Orbiter images of the south polar layered deposits), these observations generally support the conclusions that the south polar layered deposits are Late Amazonian in age and that some areas have been exposed for about 120 million years (Plaut and others, 1988; Herkenhoff and Murray, 1992, 1994; Herkenhoff, 1998). However, the recent cratering flux on Mars is poorly constrained, so inferred ages of surface units are uncertain. The Viking Orbiter 2 images used to construct the base were taken during the southern summer of 1977, with resolutions no better than 130 m/pixel. A digital mosaic of Mariner 9 images also was constructed to aid in mapping. The Mariner 9 images were taken during the southern summer of 1971 and 1972 and have resolutions as high as 85 m/pixel (table 1). However, the usefulness of the Mariner 9 mosaic image is limited by incomplete coverag

IMAP↗
USGS2022

Mechanisms and magnitude of dissolved silica release from a New England salt marsh

Salt marshes are sites of silica (SiO 2 ) cycling and export to adjacent coastal systems, where silica availability can exert an important control over coastal marine primary productivity. Mineral weathering and biologic fixation concentrate silica in these systems; however, the relative contributions of geologic versus biogenic silica dissolution to this export are not known. We collected water samples from the tidal creek of a relatively undisturbed New England (USA) salt marsh over 13 tidal cycles in spring, summer, and fall 2014–2016 to determine patterns of dissolved silica (DSi) concentration in the water entering and leaving the marsh. DSi concentrations in the tidal creek peaked in the summer and were at a minimum in the fall. Additionally, we analyzed DSi concentrations and Ge/Si ratios in marsh porewater and groundwater samples as a tracer of DSi origin. Ge/Si ratios in the porewater, subterranean estuary, and fresh groundwater averaged 6.3 ± 0.31 µmol/mol, which is consistent with production via silicate weathering rather than biogenic silica dissolution. These results highlight a previously unstudied role marsh sediment plays in coastal biogeochemistry by supplying DSi to coastal ecosystems. This marsh exported 1170 mmol DSi m −2 year −1 , 85% of which originated from porewater exchange, with minor contributions from brackish groundwater discharge from the subterranean estuary. Examining these values in the context of the other known DSi inputs indicates that coastal marshes provide ~ 75% of the annual silica inputs into the adjacent estuary, Waquoit Bay.

Massachusetts↗
USGS1983

Aeromagnetic map and interpretation of geophysical data from the Condrey Mountain Roadless Area, Siskiyou County, California

The Condrey Mountain Roadless Area lies within the Klamath Mountains geologic province, a province composed of four eastward-dipping imbricate thrust slices or belts consisting predominantly of marine arc-related volcanic and sedimentary rocks, but also including significant amounts of ultramafic and other ophiolitic rocks (Irwin, 1981). From west to east the four Klamath Mountains thrust slices are called the western Jurassic belt, the western Paleozoic and Triassic belt, the central metamorphic belt, and the eastern Klamath belt. The Condrey Mountain Road less Area is located within a structural window in the western Paleozoic and Triassic belt, a window in which the structural dome comprised of the Condrey Mountain Schist is exposed (Coleman and others, 1983). North, east and south of the roadless area, the Condrey Mountain Schist is separated from the overlying western Paleozoic and Triassic belt by a low-angle regional thrust, whereas to the west the two units are in high-angle fault contact (Coleman and others, 1983). The Condrey Mountain schist consists mainly of sedimentary and volcanic rocks metamorphosed to greenschist facies. Metasedimentary rocks are exposed over most of the eastern and central parts of the structural window. Metavolcanic rocks occupy the western part of the window but also occur in small exposures within the metasedimentary rocks and along the eastern and southern margins of the window. Tabular bodies of metaserpentinite, the largest of which crops out near White Mountain, are contained within the metasedimentary rocks. Densities of hand samples from 11 sites scattered throughout the Condrey Mountain window average 2.66±0.05 g/cm 3 . The four samples of metavolcanic rocks yielded a higher average density than the seven samples of metasedimentary rocks (2.71±0.04 g/cm 3 versus 2.63±0.03 g/cm 3 ). Along the western edge of the Condrey Mountain Road less Area, numerous narrow north-trending zones of mineralized schist extend from near Copper Butte on the south, northward to Elliot Creek (Coleman and others, 1983). These zones contain abundant pyrite mineralization associated with pyrrhotite, chalcopyrite, qalena, and sphalerite. The Blue Ledge mine area, 2 mi north-northeast of Copper Butte, is located in a zone of mineralized schist. The western Paleozoic and Triassic belt that nearly surrounds the Condrey Mountain Schist is a melange of sedimentary, volcanic, and ultramafic rocks metamorphosed to amphibolite facies (Coleman and others, 1983). Only two samples of the metamorphic melange were collected near the Condrcy Mountain Road less Area, but extensive sampling of this unit southwest of the roadless area yielded an average sample density of 2.86±0.15 g/cm 3 (112 samples) (Jachens and others, 1983).

California↗
USGS2013

Intrusive dike complexes, cumulate cores, and the extrusive growth of Hawaiian volcanoes

The Hawaiian Islands are the most geologically studied hot-spot islands in the world yet surprisingly, the only large-scale compilation of marine and land gravity data is more than 45 years old. Early surveys served as reconnaissance studies only, and detailed analyses of the crustal-density structure have been limited. Here we present a new chain-wide gravity compilation that incorporates historical island surveys, recently published work on the islands of Hawai‘i, Kaua‘i, and Ni‘ihau, and >122,000 km of newly compiled marine gravity data. Positive residual gravity anomalies reflect dense intrusive bodies, allowing us to locate current and former volcanic centers, major rift zones, and a previously suggested volcano on Ka‘ena Ridge. By inverting the residual gravity data, we generate a 3-D view of the dense, intrusive complexes and olivine-rich cumulate cores within individual volcanoes and rift zones. We find that the Hāna and Ka‘ena ridges are underlain by particularly high-density intrusive material (>2.85 g/cm 3 ) not observed beneath other Hawaiian rift zones. Contrary to previous estimates, volcanoes along the chain are shown to be composed of a small proportion of intrusive material (<30% by volume), implying that the islands are predominately built extrusively.

Hawai'i↗
USGS1997

Biostratigraphic data for the Cretaceous marine sediments in the USGS-St. George no. 1 core (DOR-211), Dorchester County, South Carolina

The USGS-St. George corehole was drilled for the U.S. Geological Survey (USGS) by a commercial drilling company during 1982. The corehole is located within the Coastal Plain Province in northern Dorchester County, South Carolina, about three miles southeast of the town of St. George near the village of Byrd (fig. 1). Coordinates for the corehole are 33o09'25'N latitude and 80o31'18'W longitude; ground elevation at the site is +78 feet (Reid and others, 1986). The St. George corehole is designated as USGS drill hole DOR-211. The St. George corehole was drilled to a total depth of 2,067 ft. The hole was cored continuously with generally good recovery from 300 ft to its total depth. Spot cores were taken at selected intervals between the top of the hole and a depth of 300 ft (50-55 ft, 100-110 ft, 150-165 ft, 200-205 ft, and 250-255 ft); however, recovery was poor in most of these intervals. The St. George core currently is stored at the USGS National Center, Reston, VA (March, 1997). The St. George corehole bottomed in basalt of probable early Mesozoic age beneath an Upper Cretaceous and Cenozoic sedi-mentary section. Reid and others (1986) placed the top of basalt saprolite at 1,962 ft in the hole. Our examination of the geophysical logs and original core descriptions suggests that the top of the saprolite is higher in the hole, at about 1,939 ft. The Cretaceous-Tertiary boundary was placed at or near 550 ft in the core by Reid and others (1986) and by Habib and Miller (1989). In this report, we provide paleontologic data for marine sediments in the upper part of the Upper Cretaceous section in the St. George core. Biostratigraphic and paleoenvironmental data and interpretations based on the study of calcareous nannofossils and ostracodes from the Cretaceous section are discussed.

Open-File Report↗
USGS2008

Coast salish and U.S. Geological Survey: Tribal journey water quality project

The ancestral waters of the Coast Salish People, the Salish Sea, comprise a large inland sea contained within both United States (Puget Sound) and Canadian (Georgia Strait) territory. The Salish Sea is home to more than 220 species of fish, 29 species of marine mammals, more than 40 species of commercial and recreationally harvested invertebrates, and numerous resident and migratory bird species (Washington Sea Grant Program, 2000). Unfortunately, at least 60 of these marine based species are listed as threatened, endangered or of concern (Fraser and others, 2006), many of which sustained Coast Salish for millennia and are of essential cultural importance. The cumulative impacts of human activities and climate change are deteriorating coastal ecosystems and accelerating the loss of ecologically and culturally important marine resources. Watershed modifications, coastal development and industrial activities are altering river and tidal flow, sediment transport, and nutrient delivery all across the region, leading to the break down of ecosystem functions and decreasing biodiversity, thus changing the face of the Salish Sea. A cooperative trans-boundary partnership between the U.S. Environmental Protection Agency (USEPA) and the Government of Canada has identified Salish Sea indicators of health. Several of these indicators have been noted as having degrading quality including urbanization and forest change, river, stream, and lake quality, marine species at risk, toxics in harbor seals, and marine water quality conditions (USEPA, 2008). The functioning of the Salish Sea ecosystem is increasingly threatened by ever more frequent observations and expanding zones of anoxia. The complexities of monitoring, protecting, and restoring such a large and diverse geographical area are exacerbated by a political border. The Coast Salish Peoples and U.S. Geological Survey (USGS) have commenced on a partnership to examine water quality throughout the Georgia Straits and Puget Sound, blending tradition and science, in response to this deterioration of coastal environments and loss of essential habitats and marine resources of cultural and ecological importance throughout the ancestral waters of the Salish Sea. This report describes the Coast Salish Tribal Journey Water Quality Project, its inception, the results of the 2008 Tribal Journey project, lessons learned, and recommendations for future directions.

Report↗
USGS2001

Delineation of tidal scour through marine geophysical techniques at Sloop Channel and Goose Creek bridges, Jones Beach State Park, Long Island, New York

Inspection of the Goose Creek Bridge in southeastern Nassau County in April 1998 by the New York State Department of Transportation (NYSDOT) indicated a separation of bridge piers from the road bed as a result of pier instability due to apparent seabed scouring by tidal currents. This prompted a cooperative study by the U.S. Geological Survey with the NYSDOT to delineate the extent of tidal scour at this bridge and at the Sloop Channel Bridge, about 0.5 mile to the south, through several marine- geophysical techniques. These techniques included use of a narrow-beam, 200-kilohertz, research-grade fathometer, a global positioning system accurate to within 3 feet, a 3.5 to 7-kilohertz seismic-reflection profiler, and an acoustic Doppler current profiler (ADCP). The ADCP was used only at the Sloop Channel Bridge; the other techniques were used at both bridges. Results indicate extensive tidal scour at both bridges. The fathometer data indicate two major scour holes nearly parallel to the Sloop Channel Bridge—one along the east side, and one along the west side (bridge is oriented north-south). The scour-hole depths are as much as 47 feet below sea level and average more than 40 feet below sea level; these scour holes also appear to have begun to connect beneath the bridge. The deepest scour is at the north end of the bridge beneath the westernmost piers. The east-west symmetry of scour at Sloop Channel Bridge suggests that flood and ebb tides produce extensive scour. The thickness of sediment that has settled within scour holes could not be interpreted from fathometer data alone because fathometer frequencies cannot penetrate beneath the sea-floor surface. The lower frequencies used in seismic-reflection profiling can penetrate the sea floor and underlying sediments, and indicate the amount of infilling of scour holes, the extent of riprap under the bridge, and the assemblages of clay, sand, and silt beneath the sea floor. The seismic- reflection surveys detected 2 to 5 feet of sediment filling the scour holes at both bridges; this indicates that the fathometer surveys were undermeasuring the effective depth of bridge scour by 2 to 5 feet through their inability to penetrate the infilled sediment. Several clay layers with thicknesses of 3 to 5 feet were detected beneath the sea floor at both bridges. Most of the piers beneath Sloop Channel Bridge appear to be surrounded by riprap, but, in several areas the riprap appears to be slumping or sliding into adjacent scour holes. Similar slumping was indicated at the Goose Creek Bridge. Most of the sediment underlying the sea floor at both bridges is interpreted as a fine-grained, cross-bedded sand. ADCP data from Sloop Channel indicate that the constricted flow beneath the bridge increases the horizontal current velocities from 2 to 6 feet per second. Total measured discharge beneath Sloop Channel Bridge was 41,800 cubic feet per second at flood tide and 27,600 cubic feet per second at ebb tide.

Water-Resources Investigations Report↗
USGS1933

Metalliferous deposits of the greater Helena mining region, Montana

The ore deposits described in this bulletin are distributed through a region of about 3,000 square miles surrounding the city of Helena, Mont. In general the surface of this region is mountainous, but it includes several large intermontane valleys. Large areas in the northern and eastern parts of the region sire underlain by sedimentary rocks of the Algonkian Belt series, and on the northeast and southwest the Belt rocks are overlain without any noticeable angular unconformity by Paleozoic and Mesozoic beds. Oligocene, Miocene, and possibly Pliocene sediments, composed chiefly of volcanic ash and land waste of local origin, occupy large areas in the intermontane valleys and lie unconformably upon Cretaceous and older rocks. A thin veneer of Pleistocene and Recent alluvium generally overspreads the Tertiary. In the extreme northern part of the region are large deposits of glacial drift that represent two stages of the Pleistocene. The principal igneous body of the region is the northern part of the early Tertiary or late Cretaceous Boulder batholitb of quartz monzonite. The main exposure of this body occupies an area of nearly 1,200 square miles and extends southward beyond the limits of the particular region considered. Smaller areas of similar rocks are clustered around this exposure. Most of the exposures probably represent bodies that are connected in depth to form a single mass. The late Cretaceous and older sedimentary rocks are involved in a series of northwestward-trending folds. Along the east side of the region overthrust faults related to the great Lewis overthrust of Glacier National Park cause Belt rocks to overlie rocks of Paleozoic and Mesozoic ages. Large normal faults occur near Marysville and faults of moderate displacement near Helena. The Tertiary beds are slightly deformed by folds and faults that are unrelated to the structure of the older rock. The geologic history of the region includes two contrasting periods, the earlier of which was characterized by the accumulation of marine sediments and the later by mountain building and erosion. The later period began with folding and elevation in late Cretaceous or early Eocene time, followed by overthrust faulting and the intrusion of the Boulder batholith. Next, there ensued a period of crustal stability, during which erosion reduced the region to a surface of low relief and cut away at least 10,000 feet of strata in the area north of Helena. In Oligocene, Miocene, and Pliocene (?) time sediments composed of land waste and volcanic ash were deposited, and this event was followed by warping and faulting that elevated the present mountains. During Pliocene and Pleistocene time the mountains were maturely dissected, and in middle and late Pleistocene time local glaciers formed in the higher mountains and large valley glaciers invaded the extreme northern part of the region. The ore deposits include lodes and placers that have yielded gold, silver, lead, copper, and zinc to a value of at least $176,860,000. The placers were formed mostly during interglacial stages of the Pleistocene. They have been almost entirely exhausted. Most of the lodes are classified as regards age in two groups, an older and a younger. The older lodes are related in origin to the Boulder batholith or some of the neighboring intrusive granitic bodies and were probably formed during early Eocene time. The younger lodes were formed after dacite of probable Miocene age was erupted. They are possibly related in origin to some unexposed intrusive granitic rock. For convenience in description the region is divided into three parts districts north of Helena, districts in the Belt Mountains, and districts south of Helena. The districts north of Helena include a 50-mile stretch of the Continental Divide that forms a broad ridge surmounted with considerable areas of flat or gently sloping surface at a general altitude of 7,000 feet. Narrow valleys 1,000 to 2,000 feet deep are cut into this surface and lead out to the neighboring wide intermontane valleys. The area is underlain mostly by shale, sandstone, and limestone of the upper part of the Belt series. Beds of Paleozoic and Mesozoic age occur south of the Belt area and extend from Helena west and northwest. The igneous rocks of the area include diorite and gabbro sills and dikes of probable Cretaceous age, extrusive andesite that is probably Oligocene or Miocene, and stocks of quartz monzonite, granodiorite, and quartz diorite, probably of Oligocene or Miocene age. The ore deposits of the northern districts are chiefly lodes that are valuable for gold and silver but contain some lead and copper. In the Ophir district bodies of gold and silver ore occur mainly in limestone near a body of quartz monzonite. In the Scratchgravel Hills and Grass Valley districts veins of gold quartz and veins containing lead-silver ore occur in quartz monzonite and in the adjoining metamorphic rocks. In the Austin district lodes containing gold; silver, lead, and copper are found in limestone near intrusive quartz monzonite. An unusual mineral in one of these lodes is corkite, a hydrous sulphate of lead containing arsenic. A small stock of quartz diorite in the Marysville district has invaded and domed Belt rocks. Marginal and radial fractures formed during the cooling and contraction of the igneous body became the receptacles of gold and silver veins, one of which, the Drumlummon, has produced $16,000,000. The veins filled open fractures and are characterized by a gangue of platy calcite and quartz. Lodes in Towsley Gulch in the western part of the district contain lead in addition to gold. In the Gould district a small stock of the granodiorite has invaded the Belt rocks and caused the deposition of veins similar to those near Marysville. In the Heddleston district lodes valuable for gold, silver, lead, and copper occur in Belt sedimentary rocks and diorite, some of them associated with porphyry dikes. In the Wolf Creek district veins in Belt rocks have produced copper ore composed mainly of chalcopyrite or chalcopyrite and tennantite accompanied by pyrite and a gangue of quartz and barite. Placer deposits along the western slope of the Belt Mountains have produced $17,500,000 in gold. Sapphires were formerly obtained from some of these deposits. The central part of the Belt Mountains is a plateaulike area considered to be the remnant of a surface produced by erosion during Tertiary time. This surface was elevated and has been deeply trenched by narrow, transverse valleys that are bordered with remnants of low terraces in which most of the placer deposits occur. Most of the western slope of the mountains is underlain by sedimentary rocks of the Belt series. At the foot of the mountains these give place to Paleozoic rocks, and these in turn are overlain unconformably in Townsend Valley by Tertiary and later deposits. The main structural feature is a great arch called the York anticline, which occupies most of the west side of the mountains. At the west foot of the mountains this fold is bordered by a series of small synclines that are tightly squeezed, faulted, and overturned as a result of pressure exerted from the west or southwest along a fracture described as the El Dorado overthrust On another fracture called1 the Scout Camp overthrust the Belt rocks composing the western slope of the mountains are thrust eastward over Paleozoic beds. Both faults are regarded as branches of the Lewis overthrust of Glacier Park. Igneous rocks that probably range in age from early Eocene to Pleistocene are widely but sparingly distributed.' They include sills and dikes of quartz dibrite, porphyry dikes, small stocks of quartz monzonite and quartz diorite, and surface flows of andesite and basalt. The deposits in the Belt Mountains that are of most interest at the present time are lodes that are chiefly valuable for gold. Most of them are found in the vicinity of York and Confederate Gulch. Nearly all are small quartz veins formed along fractures in diorite dikes and stocks or on bedding planes in the adjoining Belt sedimentary rocks. An exception is the Golden Messenger, a replacement deposit of large size but low grade, formed along fractures in a quartz diorite dike. Other veins in the same dike belong to the rather uncommon class called ladder veins. Many of the small veins contain shoots and bunches of rich ore in their upper parts. Downward- enrichment in gold is indicated to have occurred in some of the veins near York that lie below an old erosion surface. Elsewhere the origin of the placer deposits from erosion o'f the lodes during interglacial stages of the Pleistocene is indicated. Lodes containing chalcopyrite occupy tension fractures in the Belt shales that were produced by lateral movements of the mass composing the mountain front. In the districts south of Helena mining began with the discovery, on July 14, 1864, of rich placer deposits at the present site of the city of Helena, on Last Chance Creek. Since then the placer and lode deposits of these districts have produced metals worth $130,000,000 or more, of which about one-third was gold, the remainder chiefly lead and zinc. Sedimentary rocks ranging in age from Algonkian to Cretaceous underlie parts of the region, and other parts are underlain by a bedded series of andesite and latite tuffs, breccias, and flows. These rocks have been intruded and severely metamorphosed by the quartz monzonite of the Boulder batholith, the exposures of which occupy a large area. Rocks later than the intrusion of the batholith are chiefly a series of late Tertiary dacites and rhyolites. The placers of the southern districts have been almost entirely worked out. The lodes have yielded metals worth $111,600,000, but many of them are still productive. They include veins and contact-metamorphic deposits. Some of the contact deposits contain copper ore, and others contain iron ore valuable for fluxing. The veins are of two ages. The older veins have yielded most of the metallic production of the region. Their ores in general are heavy sulphide aggregates composed mainly of galena, sphalerite, and pyrite. Arsenopyrite is generally present; tetrahedrite and chalcopyrite are less common. Many of the veins are distinguished from the usual type of ore body by the occurrence of abundant tourmaline. The, metals produced are chiefly silver, lead, gold, and zinc, with some copper. The younger veins are essentially precious-metal deposits. They are mainly fissure veins but include some disseminated deposits of low grade. They are widely distributed and include several productive bodies. A distinguishing feature is the occurrence in the gangue of cryptocrystalline quartz and lamellar calcite. A dominant eastward trend of the vein fractures of the older group indicates them to be tension cracks in the crust block lying west of the Lewis overthrust that were produced by stretching in a direction at right angles to the thrust.

Montana↗
USGS2009

High-Resolution Geologic Mapping of the Inner Continental Shelf: Cape Ann to Salisbury Beach, Massachusetts

The geologic framework of the Massachusetts inner continental shelf between Cape Ann and Salisbury Beach has been shaped by a complicated history of glaciation, deglaciation, and changes in relative sea level. New geophysical data (swath bathymetry, sidescan sonar and seismic-reflection profiling), sediment samples, and seafloor photography provide insight into the geomorphic and stratigraphic record generated by these processes. High-resolution spatial data and geologic maps in this report support coastal research and efforts to understand the type, distribution, and quality of subtidal marine habitats in the Massachusetts coastal ocean.

Open-File Report↗