USGS Science⌕ Search

SEARCH · USGS Science

Results for “Stratigraphy”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62Linked to original sources
USGS2001

Geology and paleontology of five cores from Screven and Burke counties, eastern Georgia

Five deep stratigraphic test holes were drilled from 1991 to 1993 in support of multidisciplinary investigations to determine the stratigraphy of Upper Cretaceous and Tertiary sediments of the coastal plain in east-central Georgia. Cored sediment and geological logs from the Millhaven test hole in Screven County and the Girard and Millers Pond test holes in Burke County are the primary sources of lithologic and paleontologic information from this report. Lithologic and paleontologic information from the Thompson Oak and McBean test holes in Burke County supplements the discussion of stratigraphy and sedimentation in the updip part of the study area near the Millers Pond test hole.

Georgia↗
USGS2002

Crustal structure of the coastal and marine San Francisco Bay region, California

As of the time of this writing, the San Francisco Bay region is home to about 6.8 million people, ranking fifth among population centers in the United States. Most of these people live on the coastal lands along San Francisco Bay, the Sacramento River delta, and the Pacific coast. The region straddles the tectonic boundary between the Pacific and North American Plates and is crossed by several strands of the San Andreas Fault system. These faults, which are stressed by about 4 cm of relative plate motion each year, pose an obvious seismic hazard. We have many ways to study earthquake faults. Where faults break the land surface, we may learn valuable information needed for hazard assessment, such as cumulative offset, slip rate, and earthquake history. However, many of the major faults in the region are partly submerged beneath San Francisco and Monterey Bays. Although this situation poses problems in gathering observational data for hazard assessment, bay-region waterways provide an opportunity to study faultzone structure by using marine subsurface-imaging techniques, which are easier and cheaper than equivalent studies on land. In 1993, the U.S. Geological Survey (USGS) launched a 5-year project aimed at unearthing the basic science of the submerged San Andreas strike-slip fault system in the San Francisco Bay region with its many interacting strands. Primary project goals were structural, such as to discover how the San Andreas and Hayward Faults are connected or related at depth, to learn how the complex of faults in the San Andreas stepover zone on the Golden Gate platform functions, and to locate previously unknown faults. This volume thus contains mostly structural information about the San Francisco Bay region, much of it gathered through exploratory geophysical experiments. The volume is organized “top down,” from studies in the shallowest crust to the base of the crust. The first three chapters are linked through their use of novel geophysical techniques to study earthquake effects, coseismic slip, and shallow stratigraphy. Kayen and others examine crustal structure at very high resolution and demonstrate the use of ground-penetrating-radar tomography to measure the liquefaction potential of coastal sedimentary deposits. McGann and others use microfossils from drill cores along the San Francisco-Oakland Bay Bridge to determine a more detailed late Pleistocene stratigraphy of San Francisco Bay than was previously available. Geist and Zoback use the historical record of a small local tsunami generated by the great 1906 San Francisco earthquake to model the rupture process of that earthquake. The last four chapters are dedicated to studies of fault related structure of the seismogenic crust in and around the San Andreas Fault system in the San Francisco Bay region. Jachens and others compile an aeromagnetic anomaly map from new high-resolution flights across the bay region. Some of these anomalies mark the positions of offshore faults, and others are offset by faults, providing constraints on cumulative slip. Hart and others concisely summarize the marine seismic data recorded in and around San Francisco Bay, map the coverage, and provide archival information for those interested in acquiring data. The last two chapters present the results of the seismic data that have been analyzed. Bruns and others present their analysis of high-quality intermediate-resolution (~5-km penetration) seismic-reflection data gathered over the complex San Andreas-San Gregorio Fault junction. This junction, which is thought to be where the 1906 San Francisco earthquake originated (see Geist and Zoback, this volume), contains an apparent extensional right stepover in the San Andreas Fault. Finally, Parsons and others review and summarize the results of deep-crustal seismic-reflection experiments and local-earthquake tomographic studies, including previously unpublished data, and provide additional support and discussion for already-published studies. In summary, these studies were carried out in an environment where background information on faults in the San Francisco Bay region was sought. Much of the structural information presented here comes from experiments of a style unlikely to be conducted by the USGS in the near future. Together, the chapters in this volume provide a structural framework for a major part of a complex strike-slip fault system.

California↗
USGS2009

Post-Miocene Right Separation on the San Gabriel and Vasquez Creek Faults, with Supporting Chronostratigraphy, Western San Gabriel Mountains, California

The right lateral San Gabriel Fault Zone in southern California extends from the northwestern corner of the Ridge Basin southeastward to the eastern end of the San Gabriel Mountains. It bifurcates to the southeast in the northwestern San Gabriel Mountains. The northern and older branch curves eastward in the range interior. The southern younger branch, the Vasquez Creek Fault, curves southeastward to merge with the Sierra Madre Fault Zone, which separates the San Gabriel Mountains from the northern Los Angeles Basin margin. An isolated exposure of partly macrofossiliferous nearshore shallow-marine sandstone, designated the Gold Canyon beds, is part of the southwest wall of the fault zone 5.5 km northwest of the bifurcation. These beds contain multiple subordinate breccia-conglomerate lenses and are overlain unconformably by folded Pliocene-Pleistocene Saugus Formation fanglomerate. The San Gabriel Fault Zone cuts both units. Marine macrofossils from the Gold Canyon beds give an age of 5.2+-0.3 Ma by 87Sr/86Sr analyses. Magnetic polarity stratigraphy dates deposition of the overlying Saugus Formation to between 2.6 Ma and 0.78 Ma. Distinctive metaplutonic rocks of the Mount Lowe intrusive suite in the San Gabriel Range are the source of certain clasts in both the Gold Canyon beds and Saugus Formation. Angular clasts of nondurable Paleocene sandstone also occur in the Gold Canyon beds. The large size and angularity of some of the largest of both clast types in breccia-conglomerate lenses of the beds suggest landslides or debris flows from steep terrain. Sources of Mount Lowe clasts, originally to the north or northeast, are now displaced southeastward by faulting and are located between the San Gabriel and Vasquez Creek faults, indicating as much as 12+-2 km of post-Miocene Vasquez Creek Fault right separation, in accord with some prior estimates. Post-Miocene right slip thus transferred onto the Vasquez Creek Fault southeast of the bifurcation. The right separation on the Vasquez Creek Fault adds to the generally accepted 22-23 km of middle-late Miocene right separation established for the San Gabriel Fault east of the bifurcation, resulting in total right separation of 34-35 km northwest of the bifurcation. Clast sizes and lithologies in Saugus Formation deformed alluvial fan deposits in the Gold and Little Tujunga Canyons area indicate that alluvial stream flow was from the north or north-northeast. The alluvial fan complex is beheaded at the San Gabriel Fault Zone, and no correlative deposits have been found north of the fault zone. Likely sources of several distinctive clast types are east of the bifurcation and north of the Vasquez Creek Fault. Combining these data with right slip caused by the 34 deg +-6 deg of clockwise local block rotation suggests that post-Saugus Formation (<2.6 to 0.78 Ma) right separation along the fault zone is 4+-2 km. The fossils, lithology, and age of the Gold Canyon beds correlate with the basal Pico Formation. The beds presumably connected southward or southwestward to a more open marine setting. A search for correlative strata to the south and southwest found that some strata previously mapped as Towsley Formation correlate with the Modelo Formation. Oyster spat in some Modelo Formation beds are the first recorded fossil occurrences and are especially remarkable because of associations with Miocene bathyal benthic foraminifers, planktonic calcareous nannofossils, and diatoms. Topanga Group basalt resting on basement rocks between Little and Big Tujunga Canyons gives an age of 16.14+-0.05 Ma from 40Ar/39Ar analysis. Improved understanding of the upper Miocene stratigraphy indicates large early movement on the eastern Santa Susana Fault at about 7-6 Ma.

Professional Paper↗
USGS2023

Stratigraphic notes—Volume 1, 2022

This is the first volume in the U.S. Geological Survey (USGS) series of reports on stratigraphy entitled “Stratigraphic Notes,” which consists of short papers that highlight stratigraphic studies, changes in stratigraphic nomenclature, and explanations of stratigraphic names and concepts used on published geologic maps. “Stratigraphic Notes” is a long-term (multiyear), multivolume publication containing articles that address updates or revisions to stratigraphic nomenclature (and whose content ultimately will be incorporated by National Geologic Map Database personnel into Geolex, https://ngmdb.usgs.gov/Geolex/ ). We welcome papers for the “Stratigraphic Notes” series from geoscientists of the USGS, of State Geological Surveys, and from academicians. Papers can be submitted for publication in “Stratigraphic Notes” by contacting the USGS Geologic Names Committee ( gnc@usgs.gov ). As new “Stratigraphic Notes” volumes are published, links to the volumes will be posted at https://doi.org/10.3133/pp1879 . This first volume ("Stratigraphic notes—Volume 1, 2022") includes articles that provide guidance for those who wish to submit papers to “Stratigraphic Notes,” as well as information on how to make your manuscripts compliant for geologic names reviews and how to organize your paper’s content to facilitate inclusion of new or revised names in Geolex. This volume also includes some specific guidance on conducting geologic names reviews of geologic and hydrogeologic reports.

Professional Paper↗
USGS2025

Stratigraphic notes—Volume 2, 2025

This is the second volume in the U.S. Geological Survey (USGS) series of reports on stratigraphy entitled “Stratigraphic Notes,” which consists of short papers that highlight stratigraphic studies, changes in stratigraphic nomenclature, and explanations of stratigraphic names and concepts used on published geologic maps. “Stratigraphic Notes” is a long-term (multiyear), multivolume publication containing articles that address updates or revisions to stratigraphic nomenclature (and whose content ultimately will be incorporated by National Geologic Map Database personnel into Geolex, https://ngmdb.usgs.gov/Geolex/ ). We welcome papers for the “Stratigraphic Notes” series from geoscientists of the USGS, of State Geological Surveys, and from academicians. Papers can be submitted for publication in “Stratigraphic Notes” by contacting the USGS Geologic Names Committee ( gnc@usgs.gov ). As new “Stratigraphic Notes” volumes are published, links to the volumes will be posted at https://doi.org/10.3133/pp1879 .

Professional Paper↗
USGS1909

Geology and water resources of the northern portion of the Black Hills and adjoining regions in South Dakota and Wyoming

This paper, which supplements the report on the geology and water resources of the southern half of the Black Hills, published in 1901, is the result of studies made at intervals during the years 1899 to 1907. It relates to an area of about 7,500 square miles, situated about half in South Dakota and half in the northeast corner of Wyoming (Pl. II), and covering the northern half of the Black Hills uplift and a wide area of adjacent plains. The report describes the geology of the sedimentary rocks - their stratigraphy, structure, and history - and discusses their mineral resources, including underground water, coal, gypsum, etc. It also contains information respecting surface waters available for irrigation and stock raising, timber, climate, and the history of the topographic development of the region. The crystalline rocks of the central portion of the Black Hills area and the various igneous rocks of later age are shown on some of the accompanying maps but without differentiation, as the study of their geology was not within the scope of the investigation; neither are their mineral resources considered here, for these are treated in other publications. In the field work I have been assisted mainly by Prof. C. C. O'Harra, of the School of Mines at Rapid, who has mapped the geology of large areas about Aladdin, the Devils Tower, Belle Fourche, and Rapid. Dr. W. S. Tangier Smith has mapped portions of the Bear Lodge and Nigger Hill uplifts, and Mr. C. A. Fisher has assisted in portions of the work. The geology of the region from Sturgis to a point beyond Spearfish Canyon was mapped by Prof. T. A. Jaggar, jr., with the assistance of Mr. J. M. Boutwell, in 1898 and 1899. It is desirable to repeat here the statement made in my previous report that all who study the geology of the Black Hills must feel impressed by the remarkably clear general conceptions of the geologic relations of this region afforded by the survey made by Mr. Henry Newton over a quarter of a century ago. In one short season, with many unfavorable conditions for traveling, he determined most of the broader features and recorded many of the essential details. His posthumous report, edited by Mr. G. K. Gilbert, will always remain a standard work on Black Hills geology. Later studies have added greatly to our knowledge of the details of the stratigraphy and structure, the distribution of the rocks and minerals, and the age of the beds, and have afforded means for a more complete elucidation of the geologic history, especially the physiographic development of the Black Hills region.

South Dakota, Wyoming↗
USGS2009

Geologic Map of the Needles 7.5' quadrangle, California and Arizona

The Needles 7.5' quadrangle straddles the Colorado River in the southern part of the Mohave Valley, in Mohave County, Arizona, and San Bernardino County, California. The quadrangle contains part of the Havasu National Wildlife Refuge, sections of the Fort Mojave Indian Reservation, most of the city of Needles, and several major interstate highways and railroads. The quadrangle is underlain by structurally undeformed sediments of Pliocene and younger age that were deposited by the Colorado River, as well as alluvial fan deposits on the piedmonts that flank the Black Mountains (in Arizona) and the Sacramento Mountains (in California). Multiple cycles of aggradation of the Colorado River, each followed by episodes of downcutting, are recorded by Pliocene through historic deposits on the piedmonts that border the floodplain. Regionally, the complex stratigraphy related to the Colorado River has been the subject of geologic interest for over 150 years. The California and Arizona piedmont portions of the Needles quadrangle expose a subset of this incompletely understood stratigraphic record. Thus, the stratigraphic sequence presented on this map is a version of the stratigraphy of the Colorado River as interpreted locally. The deposits in the recently active Colorado River valley floor support riparian habitat and irrigated agriculture. The distributions of sand-rich channel deposits and mud-rich floodplain deposits in the valley are mapped on the basis of the history of the movement of the Colorado River in the quadrangle, which has been documented in sequential aerial photographs since 1937 and maps dating to 1857.

Arizona, California↗
USGS2010

Geologic map of the Sand Creek Pass quadrangle, Larimer County, Colorado, and Albany County, Wyoming

New geologic mapping within the Sand Creek Pass 7.5 minute quadrangle defines geologic relationships within the northern Front Range of Colorado along the Wyoming border approximately 35 km south of Laramie, Wyo. Previous mapping within the quadrangle was limited to regional reconnaissance mapping; Eaton Reservoir 7.5 minute quadrangle to the east (2008), granite of the Rawah batholith to the south (1983), Laramie River valley to the west (1979), and the Laramie 30' x 60' quadrangle to the north (2007). Fieldwork was completed during 1981 and 1982 and during 2007 and 2008. Mapping was compiled at 1:24,000-scale. Minimal petrographic work was done and no isotope work was done in the quadrangle area, but detailed petrographic and isotope studies were performed on correlative map units in surrounding areas as part of a related regional study of the northern Front Range. Stratigraphy of Proterozoic rocks is primarily based upon field observation of bulk mineral composition, macroscopic textural features, and field relationships that allow for correlation with rocks studied in greater detail outside of the map area. Stratigraphy of Phanerozoic rocks is primarily based upon correlation with similar rocks to the north in the Laramie Basin of Wyoming and to the east in the Front Range of Colorado.

Scientific Investigations Map↗
USGS2014

Geologic map of the Ute Mountain 7.5' quadrangle, Taos County, New Mexico, and Conejos and Costilla Counties, Colorado

The Ute Mountain 7.5' quadrangle is located in the south-central part of the San Luis Basin of northern New Mexico, in the Rio Grande del Norte National Monument, and contains deposits that record volcanic, tectonic, and associated alluvial and colluvial processes over the past four million years. Ute Mountain has the distinction of being one of the largest intermediate composition eruptive centers of the Taos Plateau, a largely volcanic tableland occupying the southern portion of the San Luis Basin. Ute Mountain rises to an elevation in excess of 3,000 m, nearly 700 m above the basaltic plateau at its base, and is characterized by three distinct phases of Pliocene eruptive activity recorded in the stratigraphy exposed on the flanks of the mountain and in the Rio Grande gorge. Unconformably overlain by largely flat-lying lava flows of Servilleta Basalt, the area surrounding Ute Mountain records a westward thickening of basin-fill volcanic deposits interstratified in the subsurface with Pliocene basin-fill sedimentary deposits derived from older Tertiary and Precambrian sources to the east. Superimposed on this volcanic stratigraphy are alluvial and colluvial deposits derived from the flanks of Ute Mountain and more distally-derived alluvium from the uplifted Sangre de Cristo Mountains to the east, that record a complex temporal and stratigraphic succession of Quaternary basin deposition and erosion. Pliocene and younger basin deposition was accommodated along predominantly north-trending fault-bounded grabens. These poorly exposed fault scarps cutting lava flows of Ute Mountain volcano. The Servilleta Basalt and younger surficial deposits record largely down-to-east basinward displacement. Faults are identified with varying confidence levels in the map area. Recognizing and mapping faults developed near the surface in young, brittle volcanic rocks is difficult because: (1) they tend to form fractured zones tens of meters wide rather than discrete fault planes, (2) the relative youth of the deposits has resulted in only modest displacements on most faults, and (3) some of the faults may have significant strike-slip components that do not result in large vertical offsets that are readily apparent in offset of sub-horizontal contacts. Those faults characterized as &ldquo;certain&rdquo; either have distinct offset of map units or had slip planes that were directly observed in the field. Lineaments defined from magnetic anomalies form an additional constraint on potential fault locations and are indicated as such on the map sheet.

Colorado, New Mexico↗
USGS2014

Bedrock geologic and structural map through the western Candor Colles region of Mars

The Candor Colles are a population of low, conical hills along the southeast flank of Ceti Mensa, in west Candor Chasma, within the Valles Marineris system of Mars (fig. 1). Ceti Mensa and the adjacent Candor Mensa are mounds of layered sedimentary deposits and are the most prominent landforms within west Candor Chasma. Prior to the arrival of the Mars Reconnaissance Orbiter (MRO) in orbit around Mars in 2006 (Zurek and Smrekar, 2007), geologic maps of the area utilized the relatively low resolution Viking Orbiter photomosaics (20&ndash;150 m/pixel). Geologic maps covering west Candor Chasma were created at scales of 1:15,000,000 for the western equatorial region of Mars (Scott and Tanaka, 1986), 1:2,000,000 for the Valles Marineris region (Witbeck and others, 1991), and 1:500,000 for the far eastern part of west Candor Chasma (Mars Transverse Mercator quadrangle&ndash;05072; Lucchitta, 1999). Previous structural mapping in west Candor Chasma at scales of less than 1:24,000 (Okubo and others, 2008; Okubo, 2010) employed digital terrain models (DTMs), with 1-m post spacings, derived from stereo MRO High Resolution Imaging Science Experiment (HiRISE) imagery (McEwen and others, 2010) and focused on examining the relative timing between deposition of the youngest unit of the layered deposits in this area (unit Avme of Witbeck and others, 1991) relative to regional faulting related to chasma formation. These previous mapping efforts on the southwest flank of Ceti Mensa demonstrated that unit Avme is not deformed by faults attributed to formation of the chasma. Studies of other layered deposits (primarily unit Hvl, but also including units Avme, Avsl, Avsd, and Avfs; Witbeck and others, 1991) exposed along the southeast flank of Ceti Mensa using a High-Resolution Stereo Camera (HRSC) digital terrain model (DTM) (50 m/pixel) refined the local stratigraphy and revealed evidence for syntectonic deposition of these deposits (Fueten and others, 2006, 2008; Jaumann and others, 2007; Birnie and others, 2012). Layered deposits such as those that constitute Ceti Mensa are widespread throughout the interior regions of Valles Marineris (Witbeck and others, 1991). These sedimentary deposits have been variously interpreted as eolian sediments (Nedell and others, 1987), hyaloclastic debris (Chapman and Tanaka, 2001; Komatsu and others, 2004), lacustrine or fluvial sediment (Dromart and others, 2007; Mangold and others, 2008; Metz and others, 2009), pyroclastic deposits (Hynek and others, 2003), evaporites (Mangold and others, 2008; Andrews-Hanna and others, 2010), or various combinations thereof. Recent analysis of data from the MRO Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) shows that these sediments consist primarily of hydrated sulfates (Murchie and others, 2009a,b). Further, hydrologic modeling indicates that spring-fed lakes likely occurred within the chasma (Andrews-Hanna and others, 2010). These recent findings point to a scenario in which the layered deposits accumulated as sequences of evaporites precipitating in hypersaline lakes, with contemporaneous trapping of eolian dust and sand, diagenesis, and iron-cycling, interspersed with periods of eolian and fluvial erosion (Murchie and others, 2009a). Water vapor released from these lakes may have also driven localized precipitation of snow and accumulation of layered deposits on the adjacent plateaus (Kite and others, 2011a,b). This scenario is in contrast to recent alternative interpretations that the layered deposits formed within the chasma through weathering of dust-rich ice deposits (Niles and Michalski, 2009; Michalski and Niles, 2012). The structure and geology of the layered deposits in the Candor Colles region corresponding to units Avfs, Avme, and Hvl of Witbeck and others (1991) are reevaluated in this 1:18,000-scale map. The objectives herein are to gather high-resolution structural measurements to (1) refine the previous unit boundaries in this area established by Witbeck and others (1991), (2) revise the local stratigraphy where necessary, (3) characterize bed forms to help constrain depositional processes, and (4) determine the styles and extent of deformation to better inform reconstructions of the local post-depositional geologic history.

Scientific Investigations Map↗
USGS2022

Bedrock geologic map of the Crown Point quadrangle, Essex County, New York, and Addison County, Vermont

The bedrock geology of the 7.5-minute Crown Point quadrangle consists of deformed and metamorphosed Mesoproterozoic gneisses of the Adirondack Highlands unconformably overlain by weakly deformed lower Paleozoic sedimentary rocks of the Champlain Valley. The Mesoproterozoic rocks occur on the eastern edge of the Adirondack Highlands and represent an extension of the Grenville Province of Laurentia. Granulite facies Mesoproterozoic paragneiss, marble, and amphibolite hosted the emplacement of granitic orthogneiss at approximately 1.18–1.15 giga-annum (Ga, billion years before present). The earliest of four phases of deformation (D1) is characterized by gneissosity, rarely preserved F1 isoclinal folds, and migmatite in the host rocks. Subsequent D2 deformation produced a composite penetrative gneissosity, migmatite, and isoclinal F2 folds. Towards the end of D2, felsic magmatism (including the regionally extensive Lyon Mountain Granite Gneiss, abbreviated “LMG”) spread by penetrative migration as semiconcordant alkali feldspar granite sheets subparallel to S2 into previously deformed lithologies. The LMG crystallized at approximately 1.15 Ga and displays synkinematic F2 folds thus constraining the time of D2 deformation. Exhumation during D3 produced F3 folds exhibited in regional domes and basins, such as the Keeney Mountain synform, local reactivation of the S2 foliation, partial melting, metamorphism, metasomatism, iron ore remobilization, and intrusion of magnetite-bearing pegmatite both as layer-parallel sills and crosscutting dikes. D4 created NE- and NW-trending boudinage, local high-grade ductile shear zones, and crosscutting granitic pegmatite dikes. Kilometer (km)-scale lineaments readily observed in lidar data are Ediacaran mafic dikes and Phanerozoic brittle faults. The Paleozoic rocks are part of the Early Cambrian to Late Ordovician great American carbonate bank on the ancient margin of Laurentia. Cambrian-Ordovician stratigraphy records an approximately 1-km-thick section and a transition from synrift clastics to passive margin peritidal carbonate buildups to gradually deeper water subtidal to shelf carbonates during foreland basin development associated with the Taconic orogeny. The Paleozoic rocks are weakly folded and block faulted. Large areas of the Champlain Valley are covered by undifferentiated glacial deposits, some of which contain mapped landslides. The map also shows waste rock piles and tailings from historical mining operations and large areas of artificial fill. This study was undertaken to improve our understanding of the bedrock geology in the Adirondack Highlands, establish a modern framework for 1:24,000-scale bedrock geologic mapping in the Adirondacks, provide a context for historical iron mines in the eastern Adirondacks, and update the stratigraphy of the Champlain Valley in New York and Vermont. This Scientific Investigations Map of the Crown Point 7.5-minute quadrangle consists of a map sheet, an explanatory pamphlet, and a geographic information system database that includes bedrock geologic units, faults, outcrops, and structural geologic information. The map sheet includes a bedrock geologic map, a correlation of map units, a description of map units, an explanation of map symbols, three cross sections, and a simplified surficial geologic map that includes lidar percent slope. The explanatory pamphlet includes a discussion of the geology. The bedrock geologic map on the map sheet is multi-layered and has been designed to enable the user to turn off the surficial map layer to view the concealed bedrock map units.

New York, Vermont↗
USGS2007

Application of surface geophysical methods, with emphasis on magnetic resonance soundings, to characterize the hydrostratigraphy of the Brazos River alluvium aquifer, College Station, Texas, July 2006: A pilot study

The U.S. Geological Survey, in cooperation with the Texas Water Development Board, used surface geophysical methods at the Texas A&M University Brazos River Hydrologic Field Research Site near College Station, Texas, in a pilot study, to characterize the hydrostratigraphic properties of the Brazos River alluvium aquifer and determine the effectiveness of the methods to aid in generating an improved ground-water availability model. Three non-invasive surface geophysical methods were used to characterize the electrical stratigraphy and hydraulic properties and to interpret the hydrostratigraphy of the Brazos River alluvium aquifer. Two methods, time-domain electromagnetic (TDEM) soundings and two-dimensional direct-current (2D–DC) resistivity imaging, were used to define the lateral and vertical extent of the Ships clay, the alluvium of the Brazos River alluvium aquifer, and the underlying Yegua Formation. Magnetic resonance sounding (MRS), a recently developed geophysical method, was used to derive estimates of the hydrologic properties including percentage water content and hydraulic conductivity. Results from the geophysics study demonstrated the usefulness of combined TDEM, 2D–DC resistivity, and MRS methods to reduce the need for additional boreholes in areas with data gaps and to provide more accurate information for ground-water availability models. Stratigraphically, the principal finding of this study is the relation between electrical resistivity and the depth and thickness of the subsurface hydrostratigraphic units at the site. TDEM data defined a three-layer electrical stratigraphy corresponding to a conductor-resistor-conductor that represents the hydrostratigraphic units—the Ships clay, the alluvium of the Brazos River alluvium aquifer, and the Yegua Formation. Sharp electrical boundaries occur at about 4 to 6 and 20 to 22 meters below land surface based on the TDEM data and define the geometry of the more resistive Brazos River alluvium aquifer. Variations in resistivity in the alluvium aquifer range from 10 to more than 175 ohm-meters possibly are caused by lateral changes in grain size. Resistivity increases from east to west along a profile away from the Brazos River, which signifies an increase in grain size within the alluvium aquifer and therefore a more productive zone with more abundant water in the aquifer. MRS data can help delineate the subsurface hydrostratigraphy and identify the geometric boundaries of the hydrostratigraphic units by identifying changes in the free water content, transmissivity, and hydraulic conductivity. MRS data indicate that most productive zones of the alluvium aquifer occur between 12 and 25 meters below land surface in the western part of the study area where the hydraulic conductivity can be as high as 250 meters per day. Hydrostratigraphically, individual hydraulic conductivity values derived from MRS were consistent with those from aquifer tests conducted in 1996 in the study area. Average hydraulic conductivity values from the aquifer tests range from about 61 to 80 meters per day, whereas the MRS-derived hydraulic conductivity values range from about 27 to 97 meters per day. Interpreting an interpolated profile of the hydraulic conductivity values and individual values derived from MRS can help describe the hydrostratigraphic framework of an area and constrain ground-water models for better accuracy.

Texas↗
USGS2017

Land subsidence and recovery in the Albuquerque Basin, New Mexico, 1993–2014

The Albuquerque Bernalillo County Water Utility Authority (ABCWUA) drinking water supply was almost exclusively sourced from groundwater from within the Albuquerque Basin before 2008. In 2008, the San Juan-Chama Drinking Water Project (SJCDWP) provided surface-water resources to augment the groundwater supply, allowing for a reduction in groundwater pumping in the Albuquerque Basin. In 2013, the U.S. Geological Survey, in cooperation with the ABCWUA, began a study to measure and compare aquifer-system and land-surface elevation change before and after the SJCDWP in 2008. Three methods of data collection with different temporal and spatial resolutions were used for this study: (1) aquifer-system compaction data collected continuously at a single extensometer from 1994 to 2013; (2) land-surface elevation change from Global Positioning System (GPS) surveys of a network of monuments collected in 1994–95, 2005, and 2014; and (3) spatially distributed Interferometric Synthetic Aperture Radar (InSAR) satellite data from 1993 to 2010. Collection of extensometer data allows for direct and continuous measurement of aquifer-system compaction at the extensometer location. The GPS surveys of a network of monuments allow for periodic measurements of land-surface elevation change at monument locations. Interferograms are limited in time by lifespan of the satellite, orbital pattern, and data quality but allow for measurement of gridded land-surface elevation change over the study area. Each of these methods was employed to provide a better understanding of aquifer-system compaction and land-surface elevation change for the Albuquerque Basin. Results do not show large magnitudes of subsidence in the Albuquerque Basin. High temporal-resolution but low spatial-resolution data measurements of aquifer-system compaction at the Albuquerque extensometer show elastic aquifer-system response to recovering groundwater levels. Results from the GPS survey of the network of monuments show inconsistent land-surface elevation changes over the Albuquerque Basin, likely because of the lack of significant change and the complexity of subsurface stratigraphy in addition to the spatial and temporal heterogeneity of groundwater withdrawals over the study period. Results from the InSAR analysis show areas of land-surface elevation increase after 2008, which could be attributed to elastic recovery of the aquifer system. The spatial extent to which elastic recovery of the aquifer system has resulted in recovery of land-surface elevation is limited to the in-situ measurements at the extensometer. Examination of spatially distributed InSAR data relative to limited spatial extent of the complex heterogeneity subsurface stratigraphy may explain some of the heterogeneity of land-surface elevation changes over this study period.

New Mexico↗
USGS2017

Correlation between basalt flows and radiochemical and chemical constituents in selected wells in the southwestern part of the Idaho National Laboratory, Idaho

Wastewater discharged to wells and ponds and wastes buried in shallow pits and trenches at facilities at the Idaho National Laboratory (INL) have contributed contaminants to the eastern Snake River Plain (ESRP) aquifer in the southwestern part of the INL. This report describes the correlation between subsurface stratigraphy in the southwestern part of the INL with information on the presence or absence of wastewater constituents to better understand how flow pathways in the aquifer control the movement of wastewater discharged at INL facilities. Paleomagnetic inclination was used to identify subsurface basalt flows based on similar inclination measurements, polarity, and stratigraphic position. Tritium concentrations, along with other chemical information for wells where tritium concentrations were lacking, were used as an indicator of which wells were influenced by wastewater disposal. The basalt lava flows in the upper 150 feet of the ESRP aquifer where wastewater was discharged at the Idaho Nuclear Technology and Engineering Center (INTEC) consisted of the Central Facilities Area (CFA) Buried Vent flow and the AEC Butte flow. At the Advanced Test Reactor (ATR) Complex, where wastewater would presumably pond on the surface of the water table, the CFA Buried Vent flow probably occurs as the primary stratigraphic unit present; however, AEC Butte flow also could be present at some of the locations. At the Radioactive Waste Management Complex (RWMC), where contamination from buried wastes would presumably move down through the unsaturated zone and pond on the surface of the water table, the CFA Buried Vent; Late Basal Brunhes; or Early Basal Brunhes basalt flows are the flow unit at or near the water table in different cores. In the wells closer to where wastewater disposal occurred at INTEC and the ATR-Complex, almost all the wells show wastewater influence in the upper part of the ESRP aquifer and wastewater is present in both the CFA Buried Vent flow and AEC Butte flow. The CFA Buried Vent flow and AEC Butte flow are also present in wells at and north of CFA and are all influenced by wastewater contamination. All wells with the AEC Butte flow present have wastewater influence and 83 percent of the wells with the more prevalent CFA Buried Vent flow have wastewater influence. South and southeast of CFA, most wells are not influenced by wastewater disposal and are completed in the Big Lost Flow and the CFA Buried Vent flow. Wells southwest of CFA are influenced by wastewater disposal and are completed in the Big Lost flow and CFA Buried Vent flow at the top of the aquifer. Basalt stratigraphy indicates that the CFA Buried Vent flow is the predominant flow in the upper part of the ESRP aquifer at and near the RWMC as it is present in all the wells in this area. The Late Basal Brunhes flow, Middle Basal Brunhes flow, Early Basal Brunhes flow, South Late Matuyama flow, and Matuyama flow are also present in various wells influenced by waste disposal. Some wells south of RWMC do not show wastewater influence, and the lack of wastewater influence could be due to low hydraulic conductivities. Several wells south and southeast of CFA also do not show wastewater influence. Low hydraulic conductivities or ESRP subsidence are possible causes for lack of wastewater south of CFA. Multilevel monitoring wells completed much deeper in the aquifer show influence of wastewater in numerous basalt flows. Well Middle 2051 (northwest of RWMC) does not show wastewater influence in its upper three basalt flows (CFA Buried Vent, Late Basal Brunhes, and Middle Basal Brunhes); however, wastewater is present in two deeper flows (the Matuyama and Jaramillo flows). Well USGS 131A (southwest of CFA) and USGS132 (south of RWMC) both show wastewater influence in all the basalt flows sampled in the upper 600 feet of the aquifer. Wells USGS 137A, 105, 108, and 103 completed along the southern boundary of the INL all show wastewater influence in several basalt flows including the G flow, Middle and Early Basal Brunhes flows, the South Late Matuyama flow and the Matuyama flow; however, the strongest wastewater influence appears to be in the South Late Matuyama flow. The concentrations of wastewater constituents in deeper parts of these wells support the concept of groundwater flow deepening in the southwestern part of the INL.

Idaho↗
USGS2021

Improving flood-frequency analysis with a 4,000-year record of flooding on the Tennessee River near Chattanooga, Tennessee

This comprehensive field study applied paleoflood hydrology methods to estimate the frequency of low-probability floods for the Tennessee River near Chattanooga, Tennessee. The study combined stratigraphic records of large, previously unrecorded floods with modern streamflow records and historical flood accounts. The overall approach was to (1) develop a flood chronology for the Tennessee River near Chattanooga using stratigraphic analyses and geochronology from multiple sites at multiple elevations in the study area; (2) estimate peak flow magnitudes associated with elevations of flood evidence using a one-dimensional hydraulic model; (3) combine the information obtained from steps 1 and 2 to develop a history of timing and magnitude of large floods in the study reach; and (4) use all available information (including paleoflood, gaged, and historical records of flooding) to estimate flood frequency using a standardized statistical approach for flood-frequency analysis. The stratigraphy, geochronology, and hydraulic modeling results from all paleoflood sites along the Tennessee River were distilled into an overall chronology of the number, timing, and magnitude of large unrecorded floods. In total, 30 sites were identified and the stratigraphy of 17 of those sites was closely examined, measured, and recorded. Flood-frequency analyses were done using the U.S. Geological Survey software program PeakFQ v7.2 that follows the Guidelines for Determining Flood Flow Frequency—Bulletin 17C. Resolving stratigraphic and chronologic information from all 17 sites yielded information for eight unique large floods in the last 3,500–4,000 years for the Tennessee River near Chattanooga. Two of these floods had discharges of 470,000 cubic feet per second (ft 3 /s), slightly greater than the 1867 historical peak at the Chattanooga streamgage (459,000 ft 3 /s). One flood with a discharge of 1,100,000 ft 3 /s was substantially greater than any other flood on the Tennessee River during the last several thousand years. This large flood occurred only a few hundred years ago, likely in the mid-to-late 1600s. Two additional floods in the last 1,000 years had estimated magnitudes of about 420,000 and 400,000 ft 3 /s. The remaining three unique floods identified in the paleoflood record were much smaller (less than 240,000 ft 3 /s) and occurred about 3,000–800 years ago. Flood-frequency analyses show that the addition of paleoflood information markedly improves estimates of low probability floods—most clearly shown by substantial narrowing of the 95-percent confidence limits. For the most plausible flood scenario, the 95-percent confidence interval for the 1,000-year quantile estimate derived from incorporating the four most recent paleofloods is about 480,000–620,000 ft 3 /s compared to about 380,000–610,000 ft 3 /s for the gaged and historical record alone, a reduction in the uncertainty of the estimate by 38 percent. Similarly, uncertainty for all flood quantile estimates from 100 to 10,000 years was reduced by 22–44 percent by the addition of the paleoflood record to the flood-frequency analyses.

Tennessee↗
USGS1992

Geohydrology and water quality of stratified-drift aquifers in the lower Merrimack and coastal river basins, southeastern New Hampshire

Communities in the lower Merrimack River basin and coastal river basins of southeastern New Hampshire are experiencing increased demands for water because of a rapid increase in population. The population in 1987 was 225,495 and is expected to increase by 30 percent during the next decade. As of 1987, five towns used the stratified-drift aquifers for municipal supply and withdrew an estimated 6 million gallons per day. Four towns used the bedrock aquifer for municipal supply and withdrew an average of 1 .6 million gallons per day. Stratified-drift deposits cover 78 of the 327 square miles of the study area. These deposits are generally less than 10 square miles in areal extent, and their saturated thickness ranges front less than 20 feet to as much as 100 feet. Transmissivity exceeds 4,000 square feet per day in several locations. Stratified-drift aquifers in the eastern part are predominantly small ice-contact deposits surrounded by marine sediments or till of low hydraulic conductivity. Stratified-drift aquifers in the western part consist of ice-contact and proglacial deposits that are large in areal extent and are commonly in contact with surface-water bodies. Five stratified-drift aquifers, in the towns of Derry, Windham, Kingston, North Hampton, and Greenland, have the greatest potential to supply additional amounts of water. Potential yields and contributing areas of hypothetical supply wells were estimated for an aquifer in Windham near Cobbetts Pond and for an aquifer in Kingston along the Powwow River by use of a method analogous to superposition in conjunction with a numerical ground-waterflow model. The potential yield is estimated to be 0 .6 million gallons per day for the Windham-Cobbetts Pond aquifer and 4 .0 million gallons per day for the Kingston-Powwow River aquifer. Contributing recharge area for supply wells is estimated to be 1.6 square miles in the Windham-Cobbetts Pond aquifer and 4.9 square miles in the Kingston-Powwow River aquifer. Analyses of water samples from 30 wells indicate that the water quality in the basins studied is generally suitable for drinking and other domestic purposes. Concentrations of iron and manganese exceeded the U.S. Environmental Protection Agency's (USEPA) and the New Hampshire Water Supply Engineering Bureau's secondary maximum contaminant levels for drinking water in 20 samples. With one exception, concentrations of volatile organic compounds at all wells sampled met New Hampshire Water Supply and Engineering Bureau's drinking-water standards. At one well, trichloroethylene was detected at a concentration of 5.7 micrograms per liter. Ground-water contamination has been detected at several hazardous-waste sites in the study area. Currently, 5 sites are on the USEPA's National Priority List of superfund sites, 10 sites are Resource Conservation and Recovery Act of 1976 sites, and 1 site is a Department of Defense hazardous-waste site of stratigraphic layers is a product of a material's density and the velocity at which sound travels through that material. The reflected signals return to the hydrophones at the water surface and are then filtered, amplified, and displayed graphically on the chart recorder to allow interpretation of aquifer stratigraphy and bedrock depths. Lithologic data from nearby wells and test holes were used as control points to check the interpretation of the reflection profiles. Test drilling was done at 66 locations (pls. 1-3) to determine sediment grain size, stratigraphy, depth to water table, depth to bedrock, and ground water quality. A 6-inch-diameter, hollow-stem auger was used for test drilling. Split-spoon samples of subsurface materials collected at specific depths were used to evaluate the grain-size characteristics and identify the stratigraphic sequence of materials comprising the aquifers. Thirty-eight test holes cased with a 2-inch-diameter polyvinyl-chloride (PVC) pipe and slotted screens were used to make ground-water-level measurements and collect ground-water-quality samples. Surface-water-discharge measurements were made at 16 sites during low flow when the surface water is primarily ground-water discharge. These low-flow measurements indicate quantities of ground water potentially available from aquifers. Hydraulic conductivities of aquifer materials were estimated from grain-size-distribution data from 61 samples of stratified drift. Transmissivity was estimated from well logs by assigning hydraulic conductivity to specific well-log intervals, multiplying by the saturated thickness of the interval, and summing the results. Additional transmissivity values were obtained from an analysis of specific capacity and aquifer-test data. Long-term aquifer yields and contributing areas to hypothetical supply wells were estimated by application of a method that is analogous to super position and incorporates a ground-water-flow model developed by McDonald and Harbaugh (1988). This method was applied to two aquifers judged to have the best potential for providing additional ground-water supplies. Samples of ground water from 26 test wells and 4 municipal wells were collected in March and August 1987 for analysis of common inorganic, organic, and volatile organic constituents. Methods for collecting and analyzing the samples are described by Fishman and Freidman (1989). The water-quality results from the well samples were used to characterize background water quality in the stratified-drift aquifers.

New Hampshire↗
USGS2022

Geologic characterization and depositional history of the Uteland Butte member, Green River Formation, southwestern Uinta Basin, Utah

The 15- to 65-m-thick informal Uteland Butte member of the Eocene Green River Formation represents the first widespread transgression of Lake Uinta in the Uinta Basin, Utah. This study assesses the spatial and temporal variation of Uteland Butte member deposits along a 40-km transect in the southwestern margin of the Uinta Basin using detailed measured sections, organic and inorganic geochemical data, and outcrop gamma ray logs. Fourteen lithofacies are identified, which comprise seven facies associations linked to with lacustrine, palustrine, and deltaic depositional settings. Facies associations are traceable laterally across the study area, where five 4- to 12-m-thick depositional cycles are identified. Each shallowing upwards cycle is defined by a >1.5-m-thick basal package of organic-rich, argillaceous laminated mudstone, and is capped by thick packages of bedded carbonate. In the far western study area (Kyune Creek Canyon), thick deposits of organic-rich mudstone are present and represent the most distal outcrop section; time-equivalent strata in the eastern study area (Minnie Maud Creek Canyon) are relatively organic lean with higher silt and clay content, interpreted to represent proximal lake margin deposits influenced by a nearby delta. The outcrop belt is correlated to more distal cores and well logs across the western Uinta Basin. Similar lithological and petrophysical patterns across the western Uinta Basin are used to subdivide stratigraphy into nine laterally contiguous sub-units based on nomenclature from the oil-producing area of the central basin (from base to top: lower Uteland Butte, D Bench, D Shale, C Bench, C Shale, B Bench, B Shale, A Bench, and A Shale). Siliciclastic clay-rich and carbonaterich intervals are correlated across the region and indicate distinct siliciclastic- and carbonate-dominated lake phases during Uteland Butte member deposition. Climate is interpreted to be the dominant driver of these claycarbonate cycles, in which relatively humid periods resulted in increased fluvially derived siliciclastic sediment into the basin (clay-rich periods), and arid periods resulted in evaporative conditions with decreased fluvial sediment input that favor carbonate accumulation. Climatically driven depositional cycles within the Uteland Butte member reflect, to a smaller degree, the larger scale climatically driven depositional cycles observed at the member- and formation levels of Paleocene and Eocene Uinta Basin stratigraphy. Importantly, the Uteland Butte member clay-carbonate cycles showcase how relatively small-scale climate shifts can impact basin-scale lacustrine deposition.

Utah↗