USGS Science⌕ Search

SEARCH · USGS Science

Results for “Environmental Monitoring and Assessment”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,662 records · Page 60Linked to original sources
USGS1998

Water resources of Mellette and Todd counties, South Dakota

Mellette and Todd Counties are located in south-central South Dakota and have a combined area of 2,694 square miles. The White River and its tributaries, which include the Little White River, drain Mellette County and about one-half of Todd County. Tributaries to the Niobrara River, which include the Keya Paha River, drain the other one-half of Todd County. The average discharge of the Little White River is about 56 cubic feet per second as the river enters Todd County and is about 131 cubic feet per second as it discharges to the White River in northern Mellette County. The average discharge of the Keya Paha River just outside Todd County is about 39 cubic feet per second. The average annual runoff for Mellette and Todd Counties ranges from 0.94 to 2.36 inches based on records from nine streamflow-gaging stations in and near the counties. The average annual runoff is 1.62 inches, which compares with the average annual precipitation of about 19 inches. In Todd County, shallow wells completed in the alluvial, Ogallala, Arikaree, and White River aquifers generally can supply water that has low concentrations of dissolved solids, is fresh, and is soft to moderately hard. Ground water from shallow aquifers is limited in Mellette County; therefore, deep wells, often greater than 1,000 feet, are sometimes installed. The Pierre Shale often is used to supply rural domestic and stock wells in Mellette County even though well yields are low and the water has high dissolved solids, is moderately saline, and is very hard. Alluvial aquifers are present in both counties and store an estimated 1.6 million acre-feet of water. The water quality of the alluvial aquifers is dependent on the underlying deposits, and generally the water has low concentrations of dissolved solids, is fresh, and is soft to moderately hard where underlain by the Ogallala and Arikaree Formations; has moderate concentrations of dissolved solids, is slightly saline, and is hard where underlain by the White River Group; and has high concentrations of dissolved solids, is saline, and is very hard where underlain by the Pierre Shale. Also, yields often are lower where the alluvial aquifers are underlain by the Pierre Shale. The Ogallala aquifer is present in only Todd County, and the Arikaree aquifer is present throughout most of Todd County and southwestern and south-central Mellette County. The Ogallala aquifer contains an estimated 17 million acre-feet of water in storage, and the Arikaree aquifer contains an estimated 50 million acre-feet of water in storage. Both aquifers generally are suitable for irrigation, and yields from these aquifers are sometimes greater than 1,000 gallons per minute. Nitrate concentrations in 13 out of 92 water samples collected from the Ogallala aquifer exceeded the Primary Drinking Water Maximum Contaminant Level (MCL) of 10 milligrams per liter. In 11 out of 46 samples collected from the Arikaree aquifer, arsenic concentrations exceeded the MCL of 50 micrograms per liter. The White River aquifer, where present, is usually the shallowest source of ground water in Mellette County. The White River aquifer also is used in northern Todd County where the Ogallala and Arikaree aquifers are not present. The White River aquifer contains an estimated 50 million acre-feet of water in storage. Reported yields from the aquifer range from 1 to 30 gallons per minute, which generally is insufficient to support irrigation in most areas. However, yields are sufficient for livestock-watering and rural-domestic purposes. In both counties, the Pierre Shale is the shallowest bedrock aquifer and is exposed at the land surface throughout most of Mellette County. This aquifer is used primarily in Mellette County. Although the aquifer contains an estimated maximum of 1.5 million acre-feet of water in storage, it is not a viable source of ground water because the aquifer is relatively impermeable, yields are low, and water usually can be obtained from shallower sources, especially in Todd County. Reported yields from the Pierre Shale aquifer range from 1 to 8 gallons per minute. Because few test holes and wells penetrate below the Pierre Shale, little is known about the extent of the deeper bedrock aquifers. All wells completed in the Dakota Sandstone, Inyan Kara, and Minnelusa and Madison aquifers in the counties are used for stock-watering purposes. High concentrations of dissolved solids and hard water are characteristic of the water quality in the bedrock aquifers. Depths to the top of the deeper bedrock aquifers range from 1,270 feet to greater than 2,000 feet below land surface.

South Dakota↗
USGS2025

The role of bedrock circulation depth and porosity in mountain streamflow response to prolonged drought

Quantitative understanding is lacking on how the depth of active groundwater circulation in bedrock affects mountain streamflow response to a multi‐year drought. We use an integrated hydrological model to explore the sensitivity of a variety of streamflow metrics to bedrock circulation depth and porosity under a plausible extreme drought scenario lasting up to 5 years. Endmember depth versus hydraulic conductivity relationships and porosity values for fractured crystalline rock are simulated. With drought, a deeper circulation system with higher drainable porosity more effectively buffers minimum flow and significantly limits perennial stream loss in comparison to a shallow circulation system. Streamflow buffering is accomplished through extensive groundwater storage loss. However, deeper circulation systems experience prolonged recovery from drought in comparison to storage‐limited shallow systems. Research highlights the importance of characterizing the deeper bedrock hydrogeology in mountainous watersheds to better understand and predict drought impacts on stream ecosystem health and water resource sustainability.

Colorado↗
USGS2026

A process-based model for forecasting wave runup along the coast of Georgia

Wave runup is an important nearshore process that impacts total water level, sediment transport, and coastal design. Current methods for forecasting wave runup implement an empirical model that considers offshore wave height, wave period, and generalized beach slope. In this study, the authors generated wave runup forecasts from offshore wave conditions and a system of polynomial equations derived from numerical simulations at three different still water datums for each beach profile. They developed a process-based methodology that incorporated site-specific cross-shore topobathy into the phase-resolving numerical model. A comparison between the system of equations, deterministic hydrodynamic simulations, and observed high-water marks was made using Hurricanes Matthew (2016) and Irma (2017) for 12 cases, and it showed that the polynomials were capable of being consistent with the results from full simulation runs, while not requiring hours of runtime when a forecast was needed—the differences between the polynomial and the observed high water marks ranged from 3 to 32 cm for the Irma hindcast and 9–70 cm for Matthew. Then, using forcings from Hurricanes Ian and Nicole (2022), the model predicted the occurrence of dune collision, overwash, and inundation for the coast of Georgia and suggested that wave runup was impacted by the still water level and local topobathy.

Georgia↗
USGS2023

A comprehensive fault system inversion approach: Methods and application to NSHM23

We present updated inversion‐based fault‐system solutions for the 2023 update to the National Seismic Hazard Model (NSHM23), standardizing earthquake rate model calculations on crustal faults across the western United States. We build upon the inversion methodology used in the Third Uniform California Earthquake Rupture Forecast (UCERF3) to solve for time‐independent rates of earthquakes in an interconnected fault system. The updated model explicitly maps out a wide range of fault recurrence and segmentation behavior (epistemic uncertainty), more completely exploring the solution space of viable models beyond those of UCERF3. We also improve the simulated annealing implementation, greatly increasing computational efficiency (and thus inversion convergence), and introduce an adaptive constraint weight calculation algorithm that helps to mediate between competing constraints. Hazard calculations show that ingredient changes (especially fault and deformation models) are the primary driver of hazard changes between NSHM23 and UCERF3. Updates to the inversion methodology are also consequential near faults in which the slip rate in UCERF3 was poorly fit or was satisfied primarily using large multifault ruptures that are now restricted by explicit b ‐value and segmentation constraints.

Bulletin of the Seismological Society of America↗
USGS2024

Mapping Arundo donax (Arundo cane) with multispectral imagery before, during, and after herbicide treatment along the Rio Grande in Webb County, Texas, 2020–21

Arundo donax , commonly called Arundo cane, giant reed, or Carrizo cane, is an invasive bamboo-like perennial grass common in riparian areas throughout the southwestern United States. In Texas, not only does it negatively affect riparian ecosystems, but it has also become a problem for border security because it reduces visibility along the Rio Grande. To address these problems, in 2015 the Texas State Soil and Water Conservation Board was authorized by the Texas State Legislature to develop a program to eradicate Arundo cane along the Rio Grande. In 2020, the Texas State Soil and Water Conservation Board applied imazapyr and glyphosate herbicides along a 19.3-kilometer reach of the Rio Grande, northwest of Laredo, Texas. The U.S. Geological Survey, in cooperation with the Texas State Soil and Water Conservation Board and the Webb Soil and Water Conservation District, used WorldView-3 Standard high-resolution satellite imagery to map Arundo cane extent along the reach before , during , and after the herbicide-treatment period on June 30, 2020, September 26, 2020, and May 7, 2021, respectively. A maximum likelihood supervised classification analysis was computed on the images to map the spatial extent and estimate the area covered by Arundo cane. The estimated area covered by Arundo cane in the before classification was 1,282,000 square meters, in the during classification was 1,064,000 square meters, and in the after classification was 1,108,000 square meters. The qualitative comparison of the three images shows that there was an overall decrease in vegetation classified as Arundo cane throughout the study area.

Texas↗
USGS2025

Airborne geophysics for geologic mapping of critical mineral systems in the United States southern midcontinent

The increased demand for clean energy technology and a significant reliance on foreign supply chains have given impetus to understanding critical mineral systems and locating potential resources within the United States. At least thirteen critical mineral-bearing systems have been identified throughout the U.S. southern Midcontinent (Hofstra and Kreiner, 2020) but much of the region’s geologic framework is concealed by vegetation and sedimentary cover that hinder traditional geologic mapping efforts. Airborne geophysical data provide an effective way to overcome these obstacles and to provide additional insight into the deeper structures that underlie shallow mineralization. However, legacy airborne magnetic and radiometric data were collected using now-outdated instruments and methods, inconsistent survey parameters, and large flight-line spacings resulting in low-resolution data that present challenges to regional-scale study and interpretation. Over the last decade, the U.S. Geological Survey Earth Mapping Resources Initiative (EMRI) and National Cooperative Geologic Mapping Program have conducted a series of high-resolution airborne magnetic and radiometric surveys across the southern Midcontinent (Fig. 1) as part of an effort to improve understanding of the geophysical framework and natural resource potential in the region. These surveys are designed using modern survey methods and instruments with consistent parameters for flight-line spacing and flight height relative to magnetic sources. The EMRI airborne surveys are planned in collaboration with State geological surveys based on focus areas (Dicken et al., 2022) according to the presence of or potential for critical mineral deposits. High-resolution airborne magnetic and radiometric data cover focus areas such as the southeast Missouri iron metallogenic province and South-Central iron-oxide-apatite (IOA) – iron-oxide-copper-gold (IOCG) province, the Magnet Cove alkaline-carbonatite complex, the Midwest Permian ultramafic dike district, the Illinois-Kentucky fluorspar district, and several Mississippi Valley-type lead-zinc deposits and districts (Fig. 1). These focus areas represent known deposits or prospective host systems of critical minerals including rare earth elements (REEs), platinum-group elements (PGEs), cobalt, lithium, fluorspar, niobium, titanium, vanadium, lead, zinc, gallium, germanium, and many more. Other significant geologic and geophysical features covered include the Reelfoot rift, the New Madrid seismic zone, the Illinois basin, the Arkoma basin, the South-Central magnetic lineament, and the Kentucky-Tennessee magnetic anomaly (Fig. 1). This presentation focuses on new airborne magnetic and radiometric data with continuous coverage across parts of six states, preliminary interpretations, examples of geologic mapping applications, and discussion of newly discovered magnetic anomalies and follow-up investigations.

Conference Paper↗
USGS2025

Quantifying groundwater response and uncertainty in beaver-influenced mountainous floodplains using machine learning-based model calibration

Beavers ( Castor canadensis ) alter river corridor hydrology by creating ponds and inundating floodplains, and thereby improving surface water storage. However, the impact of inundation on groundwater, particularly in mountainous alluvial floodplains with permeable gravel/cobble layers overlain by a soil layer, remains uncertain. Numerical modeling across various floodplain structures considers topographic and sediment complexity and multidirectional flow, linking inundation to groundwater response. This study develops a model-data integration workflow to address uncertainty in groundwater response to beaver-induced inundations in a mountainous alluvial floodplain in the Upper Colorado River Basin. Uncertain factors include seasonal hydrologic dynamics, hydraulic conductivities, floodplain structures, and meteorological forcings. We employed an ensemble of groundwater models, based on geophysical and hydrologic data, with machine learning-based calibration using a neural density estimator. This allowed us to quantify the vertical flux from the soil layer to the permeable gravel bed, the down-valley underflow within the gravel bed, and their ratios. Results show a significant increase in the vertical flux relative to down-valley underflow, from 2% during dry pond periods to 20% during wet periods, serving as an analogy for conditions without and with beaver ponds. The study highlights the influence of floodplain structure on groundwater storage, water balance, and water quality impacted by beaver ponds. A thick gravel bed layer, with a large down-valley underflow, minimizes the effect of beaver-induced inundation on water quality. We emphasize the need for field-scale measurements of floodplain structure and improved characterization of evapotranspiration changes to reduce uncertainty in groundwater response.

Colorado↗
USGS1976

Water-quality study of a reach of the Merced River in Yosemite National Park and vicinity, California, April 1973 through September 1974

A 25-mile (40-kilometre) reach of the Merced River was studied to provide the National Park Service with water-quality data prior to the operation of a new sewage-treatment plant. Data were collected periodically at four Merced River and two inflow stations. Discharge varied seasonally with highest flow occurring at the time of spring snowmelt runoff. Lowest flow occurred during late summer, coinciding with high park visitor use and elevated water temperature. Water-quality variables investigated were discharge, temperature, major chemical constituents, selected trace metals, specific conductance, suspended sediment, turbidity, dissolved oxygen, pH, alkalinity, carbon dioxide, total organic carbon, nitrogen, phosphorus, algal growth potential, coliform bacteria, periphyton, and benthic invertebrates. Diel measurements were made at some stations to delineate daily fluctuations in selected water-quality variables. Results indicate that water in the reach of the Merced River studied was of good quality. The river had low concentrations of dissolved solids (8 to 41 milligrams per litre) and low alkalinity values (2 to 24 milligrams per litre of alkalinity as CaCO 3 ). Mean concentrations of nitrogen and phosphorus were highest in the Merced River at Rancheria Flat. Algal growth potential tests showed that phosphorus was limiting algal growth at Happy Isles Bridge, El Capitan Bridge, and South Fork Merced River, whereas nitrogen was limiting growth at Rancheria Flat. Input of excessive nitrogen and phosphorus concentrations in the Merced River during the summer low-flow period, and mixing with warm tributary inflow could cause excessive algal growth and production. The algal types found were diatoms, green algae, and blue-green algae. Biomass/chlorophyll a ratios in the Merced River were low (0.3 to 7.7). Benthic invertebrates consisted chiefly of Diptera, Ephemeroptera, and Plecoptera.

California↗
USGS2025

Bayesian ETAS modeling for the Pacific Northwest: Uncovering effects of tectonic regimes, regional differences, and swarms on aftershock parameters

The Pacific Northwest (PNW) of North America has high seismic hazard due to numerous earthquake sources under populated areas. It hosts several tectonic regimes and subregional seismic zones that are hypothesized to have different patterns of earthquake and aftershock occurrence. It is also predisposed to earthquake swarms, which can complicate the statistical modeling of these patterns. We present the first statistical seismicity model of the PNW catalog using the epidemic‐type aftershock sequence (ETAS) framework. We develop a Bayesian inference procedure that provides a stable estimation of both ETAS parameters and their uncertainties for different sets of PNW earthquakes, even those with very sparse catalogs. The Bayesian approach allows us to investigate how parameter estimates change between the intraslab and crustal tectonic regimes, the northern and southern PNW, and when swarms are included and excluded from the catalog. We also utilize our Bayesian framework to calculate parameter estimates under different prior beliefs about PNW seismicity, as well as to propagate catalog measurement errors into ETAS parameter estimates. We discuss the implications of parameter differences across the region for aftershock forecasting for the PNW.

Pacific Northwest↗
USGS1976

A comparison of electronic particle counting and pipette techniques in routine mud analysis

Electronic particle counting and pipette size-analysis techniques are compared for their relative effectiveness in large-scale routine mud analysis. Optimum laboratory procedures for conducting electronic analyses with a Model TA Coulter Counter are presented. Comparative electronic and pipette analyses conducted on the same samples resulted in equivalent precision for both techniques. Results of electronic analyses consistently showed size distributions significantly coarser than those obtained by pipette analyses. The laboratory efficiency of the relatively rapid electronic technique is far superior to that of the pipette technique, although more extensive precautionary measures are required to maintain a high level of analytical accuracy and precision. The quality of electronic analyses largely depends upon the effectiveness of standardized operational procedures established within the laboratory.

Open-File Report↗
USGS2025

Linking stream-reach nitrogen loads and groundwater “reachsheds” to inform wastewater-nitrogen management actions, Cape Cod, Massachusetts

Study Region Cape Cod, Massachusetts, U.S.A. Study Focus Anthropogenic nitrogen (N) is a key factor in degrading groundwater and surface-water quality, particularly in coastal New England where onsite wastewater systems are prevalent. This study evaluated whether direct N-load measurements in streams on Cape Cod, Massachusetts, coupled with flow-path information from groundwater-flow models, can effectively identify potential land areas where nitrogen mitigation could substantially reduce loads to receiving waters. Nitrogen fluxes were measured along 63 stream reaches during winter and summer and paired with simulated groundwater recharge areas to identify and rank potential areas for reduction of nonpoint-source N inputs. New Hydrologic Insights for the Region Reach-scale nitrate-N loads ranged from −39.1–1182 kg-N/yr per 100 m of stream, indicating spatially variable groundwater inputs across seasons. “Reachsheds” — areas contributing groundwater recharge to specific stream reaches — were delineated using a regional groundwater-flow model. Strong correlations were found between observed N loads and land-use characteristics, especially the number of septic systems and total N inputs from the sum of considered sources. Observed N loads were moderately correlated with recharge area size and wastewater flow estimates. Correlating reach-specific groundwater N loads with land use and parcel-scale nitrogen-yield data identified reachsheds with the highest potential for N load reduction. This approach enables targeted implementation of restoration efforts to optimize nutrient management and support regional load reduction.

Massachusetts↗
USGS2025

Groundwater salinity: Applying the specific conductance and water type proxy

Groundwater is increasingly needed for water supplies but may have limited utility in some locations because of its salinity. Salinity, often expressed as total dissolved solid (TDS), is frequently estimated using specific conductance (SC) measurements. However, the commonly used proxy (0.65 multiplied by SC to indicate TDS, common in many handheld meters) can result in inaccurate TDS estimates. First, the TDS–SC relationship is not linear over the entire concentration range of groundwater. Furthermore, the TDS (and salinity)–SC relationships vary substantially depending on the major-ion composition. Here we develop a proxy method utilizing SC and major-ion water type to estimate TDS and salinity specifically for groundwaters. Compared to most surface waters, groundwater tends to have a wider range of salinity (fresh to highly saline) and higher concentrations of bedrock-derived solutes such as carbonate ions, silica, and many other ions. The dataset used to develop the proxies includes water chemistry data from 149,059 discrete groundwater samples. The groundwater proxies, which employ nonlinear log–log relations, utilize five water types (HCO 3 , Cl, Ca-Mg-SO 4 , Na-K-SO 4 , and mixed waters), are accurate (median percent difference between TDS and salinity determined using the proxy compared to discrete measurements was <±0.8%) over a wide range of SC (up to 200 mS/cm), rapid, cost-effective, and can be measured on-site.

Groundwater↗
USGS2026

Upper Triassic igneous rocks of the southern Kenai Peninsula, Alaska – Prelude to Early Jurassic subduction along the western Wrangellia composite terrane margin

New U–Pb zircon geochronology identifies a latest Triassic (ca 214–201 Ma) igneous suite of tuff, hypabyssal dikes, and a pluton on the southern Kenai Peninsula, Alaska. The igneous suite was emplaced within Upper Triassic sedimentary rocks along the southern margin of Western Wrangellia, the western-most fragment of the Wrangellia composite terrane. The igneous rocks range from mafic (50.6% SiO 2 ) to felsic (78.3% SiO 2 ), characteristically have less than 1.55% K 2 O, and generally have low trace element abundances. The tonalitic and trondhjemitic magmas were largely sourced in mafic-rich lower crust and incompletely assimilated quartz and other mineral xenocrysts are common. Fractionation involving plagioclase and amphibole is indicated for some magmas and composite intrusions and igneous xenoliths indicate magma mixing was possible. Paleozoic and Precambrian inherited zircons and initial 87 Sr/ 86 Sr (0.704103–0.705609) and 143 Nd/ 144 Nd (0.512396–0.512777) ratios indicate that the Western Wrangellia crustal sources are heterogeneous and contain sialic components. The latest Triassic magmatism reflects processes that preceded Early Jurassic subduction along the Wrangellia composite terrane and Pacific Ocean plate boundary. These processes involved heating and melting of mantle lithosphere and lower crust as mantle instabilities accompanied the breaking of the plate boundary linkages. The Late Triassic transition to subduction along the Wrangellia composite terrane margin coincided with the transition to subduction cessation in the Late Triassic arcs of the western Intermontane terranes of Canada. The shift to subduction along the outboard Wrangellia composite terrane margin marks the beginning of the Pacific Ocean–Cordillera plate interactions that came to dominate the tectonic evolution of the northern Cordillera from the Early Jurassic to today.

Alaska↗
USGS1998

Transmissivity and water quality of water-producing zones in the intermediate aquifer system, Sarasota County, Florida

The intermediate aquifer system is an important water source in Sarasota County, Florida, because the quality of water in it is usually better than that in the underlying Upper Floridan aquifer. The intermediate aquifer system consists of a group of up to three water-producing zones separated by less-permeable units that restrict the vertical movement of ground water between zones. The diverse lithology, that makes up the intermediate aquifer system, reflects the variety of depositional environments that occurred during the late Oligocene and Miocene epochs. Slight changes in the depositional environment resulted in aquifer heterogeneity, creating both localized connection between water-producing zones and abrupt culmination of water-producing zones that are not well documented. Aquifer heterogeneity results in vertical and areal variability in hydraulic and water-quality properties. The uppermost water-producing zone is designated producing zone 1 but is not extensively used because of its limited production capability and limited areal extent. The second water-producing zone is designated producing zone 2, and most of the domestic- and irrigation-supply wells in the area are open to this zone. Additionally, producing zone 2 is utilized for public supply in southern coastal areas of Sarasota County. Producing zone 3 is the lowermost and most productive water-producing zone in the intermediate aquifer system. Public-supply well fields serving the cities of Sarasota and Venice, as well as the Plantation and Mabry Carlton Reserve well fields, utilize producing zone 3. Heads within the intermediate aquifer system generally increase with aquifer depth. However, localized head-gradient reversals occur in the study area, coinciding with sites of intense ground-water withdrawals. Heads in producing zones 1, 2, and 3 range from 1 to 23, 0.2 to 34, and 7 to 42 feet above sea level, respectively. Generally, an upward head gradient exists between producing zones 3 and 2. However, an upward head gradient between producing zones 2 and 1 does not consistently occur throughout Sarasota County, probably the result of greater ground-water withdrawals from producing zone 2 than from producing zone 1. The transmissivity of the intermediate aquifer system is spatially variable. Specific-capacity data from selected wells penetrating producing zones 2 and 3, were used to estimate transmissivity. Estimated transmissivity values for producing zones 2 and 3 range from about 100 to 26,000 feet squared per day and from about 1,300 to 6,200 feet squared per day, respectively. Because the capacity of specific water-producing zones is highly variable from site to site, estimating the performance of a specific water-producing zone as a water resource is difficult. Water samples collected during the study were analyzed for major-ion concentrations. Generally, bicarbonate type water from rock interaction occurs in northern Sarasota County; enriched calcium-magnesium-sulfate type water from deeper aquifers occurs in central Sarasota County; and sodium-chloride type water from saltwater mixing occurs in southern Sarasota County. In some areas of northern Sarasota County, the major-ion concentrations in water are lower in producing zone 2 than in producing zone 1. Major-ion concentrations in water are higher in producing zone 3 throughout the study area. A major objective of the study was to evaluate hydraulic and water-quality data to determine distinctions that could be used to characterize a particular producing zone. However, data indicate that both hydraulic and water-quality properties are highly variable within and between zones, and are more related to the degree of connection between and areal extent of water-producing zones than to aquifer depth and distance from the coast.

Florida↗
USGS2026

Moment magnitude for small earthquakes in the Delaware basin of west Texas and southeast New Mexico, USA

The Delaware Basin region of west Texas and southeast New Mexico has become one of the most prolific regions of seismic activity in the continental United States due to widespread hydraulic fracturing and wastewater disposal injection. In response to the increased number of earthquakes in this region, rapid and accurate characterization of earthquake sources is necessary to understand the evolution of seismic activity and level of seismic hazard associated with these earthquakes. This study re-evaluates earthquake magnitudes, estimating moment magnitude (MW) for small earthquakes in the Delaware Basin using 1) moment-rate spectra derived from S-wave coda envelopes, and 2) a relative magnitude method that relies exclusively on the ratio of waveform amplitudes between highly correlated waveform pairs. The coda-envelope method produces accurate M W estimates for small earthquakes ( M 1.5 – 3) that are consistent with independent, waveform modeled moment magnitudes for events with M W > 3 . Using the relative amplitudes method to extend these M W magnitudes to many other events, we successfully provide relative moment magnitude ( M W,rel ) values for 81% of the Texas Seismological Network catalog in the Delaware Basin region, and 45% of the USGS Induced Seismicity Project’s catalog of events in southeast New Mexico. The adoption and integration of the calibrated M W,rel method with current magnitude estimation methods offers valuable insights into the relationships between local and moment magnitude and will contribute to improved characterization of widespread induced seismicity.

New Mexico, Texas↗
USGS2025

Structural setting and geothermal potential of northeastern Reese River Valley, north-central Nevada: Highly prospective detailed study site for the INGENIOUS project

The northeastern part of the Reese River basin situated ~15 km southeast of Battle Mountain, Nevada, scored highly in the Nevada geothermal play fairway analysis (PFA) for hosting potential hidden geothermal systems. This site (also referred to as Argenta Rise) was therefore chosen for detailed study in the INGENIOUS project (INnovative Geothermal Exploration through Novel Investigations Of Undiscovered Systems). The high PFA scores resulted primarily from favorable structural settings (e.g., fault intersections and pull aparts) with relatively high slip rates on Quaternary faults. The INGENIOUS project is utilizing additional parameters and more rigorous analytical techniques to further advance exploration at this site. This includes integration of geological (e.g., Quaternary fault mapping) and new geophysical datasets (e.g., gravity, magnetics, MT data, and five reprocessed seismic reflection profiles) to build a structural model and to identify specific favorable sites for potential geothermal upwellings. Two-meter temperature surveys were also conducted in the area (139 measurements). This part of north-central Nevada is characterized by systems of intersecting northerly and ENE-striking faults within the broader Humboldt structural zone, a poorly understood belt of ENE-striking faults and relatively high heat flow extending across northern Nevada. Kinematic analysis of exposed fault surfaces shows that ENE-striking faults have accommodated sinistral-normal slip, and normal slip characterizes N- to NNE-striking faults. Northeastern Reese River Valley lies within a broad left step between major ENE-striking fault zones on the northern flanks of the Argenta Rim and Shoshone Range and thus corresponds to a broad pull-apart in the ENE-striking sinistral-normal fault system. Notably, the nearby Beowawe geothermal system in Whirlwind Valley (with abundant sinter, hot springs, and a geothermal power plant) occupies a fault intersection in a relatively small left step in a major ENE-striking sinistral-normal fault and may serve as an analogue for a potential hidden system in northeastern Reese River Valley. Existing geological maps, high-resolution lidar, and seismic reflection data demonstrate that northeastern Reese River Valley is structurally complex with multiple intersections between the ENE- and N- to NNE-striking fault systems. Some of these fault intersections correspond to low resistivity anomalies, magnetic lows, and/or very subtle 2-m temperature anomalies, which may indicate hidden geothermal upwellings. Three-dimensional modeling and temperature-gradient drilling are planned to further evaluate these sites for geothermal activity.

Nevada↗
USGS2026

Mineral chemistry perspective on remobilization of stored magma at Kamakai'a Hills, Southwest Rift Zone of Kilauea, Island of Hawai'i, USA

Differentiated magmas stored in the rift zones of Kīlauea have received more attention in recent years following eruption of andesite during the early phase of 2018 lower East Rift Zone activity. Despite this growing interest, some of the most voluminous eruptions of differentiated rift zone magmas remain poorly studied. One such eruption, and the most voluminous exposed differentiated flow field at Kīlauea, is the Kamakaiʻa Hills. This eruption took place in the Southwest Rift Zone of Kīlauea, a region that is hypothesized to contain a long-lived rift zone reservoir. The Kamakaiʻa Hills flow field encompasses >250 × 10 6 m 3 of basaltic andesite and basalt compositions with a mineral assemblage of orthopyroxene + clinopyroxene + plagioclase during its early ʻaʻā phase and clinopyroxene + plagioclase + olivine during its late pāhoehoe phase. To better understand storage conditions and magma accumulation, this study focuses on major, minor, and trace elements from the mineral assemblage present within the early ʻaʻā and late pāhoehoe phases. The diversity of clinopyroxene and plagioclase compositions within the early ʻaʻā and late pāhoehoe phases, as well as diverse compositions of plagioclase and orthopyroxene within the early ʻaʻā phase, suggest multiple magma bodies and limited pre-eruption magma mixing within the broader Kamakaiʻa Hills reservoir. Oscillatory zoning patterns (particularly in clinopyroxene) imply processes such as recharge events, magma mixing or mingling, or convection within a differentially cooling, chemically stratified reservoir over protracted time intervals, whereas only limited resorbed mineral textures indicate incomplete mixing of heat and chemically distinct magmas during the dike intrusion that triggered the eruption. Mineral-mineral and mineral-melt thermobarometry indicate predominantly shallow (≤2.5 km depth) crustal storage conditions of the cooled, differentiated magma (∼1100 °C and cooler for the basaltic andesites) to hotter temperatures for the basalts (all >1100 °C). Despite the known large standard errors estimated for mineral-melt and mineral-mineral barometry (10s to >100 MPa), the calculated pressures and depths broadly correspond with earthquake swarm depths beneath the Kamakaiʻa Hills, and drill core and fluid inclusion barometry storage depths of differentiated magmas within the lower East Rift Zone. The Kamakaiʻa Hills differentiated magmas have H 2 O contents (∼0.5 wt%, using plagioclase-melt hygrometry) equivalent to typical Kīlauea basalts. Our data and interpretations demonstrate a complex, long-lived rift zone storage system that consisted of multiple magma bodies and was mobilized into eruption through intrusion of a hotter and more primitive summit-derived (uprift) magma.

Hawaii↗
USGS2024

Global variability of the composition and temperature at the 410-km discontinuity from receiver function analysis of dense arrays

Seismic boundaries caused by phase transitions between olivine polymorphs in Earth's mantle provide thermal and compositional markers that inform mantle dynamics. Seismic studies of the mantle transition zone often use either global averaging with sparse arrays or regional sampling from a single dense array. The intermediate approach of this study utilizes many densely spaced seismic arrays distributed around the globe. We systematically compute teleseismic P-to-S receiver functions for each seismic array and invert for the 1-D seismic velocity structure of the mantle transition zone beneath each array to facilitate a comparison between densely sampled regions. We stack 3,600 receiver functions on average at 67 arrays in total. The stack is used in a probabilistic inversion to estimate the mantle transition zone interface depths and velocities beneath each array. We focus on the 410-km discontinuity (410) because it is a prominent seismic interface that is clearly linked to a single mineral phase transition between olivine and wadsleyite. The depths and velocity contrasts of the 410 are mapped to temperatures and compositions using mineral physics constraints. The depth of the 410 ranges from ∼405–440 km, which is consistent with a ∼360 K temperature range in a dry mantle and a ∼260 K temperature range in a wet mantle (2 wt. % water). The Vs contrast across the 410 ranges from ∼2.5–8 %, which is consistent with ∼20–70 vol. % olivine composition in a dry mantle and ∼25–80 vol. % in a wet mantle. The bulk composition of the upper mantle near the 410-km discontinuity is typically considered to be well-mixed because there is no thermodynamic impediment to convection at the olivine to wadsleyite phase transition. However, the wide range of inferred olivine content from our study suggests that there are large lateral variations in the bulk composition of the upper mantle near the 410-km discontinuity.

Earth and Planetary Science Letters↗