USGS Science⌕ Search

SEARCH · USGS Science

Results for “Arctic, Antarctic, and Alpine Research”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,661 records · Page 60Linked to original sources
USGS2026

Shallow hydrogeologic framework of the Tully Valley mudboil area, Onondaga County, New York

Mudboils have been documented in the Tully Valley in southern Onondaga County, New York, since the late 1890s. Sediment-laden water from the mudboils flows into Onondaga Creek, which empties into Onondaga Lake at Syracuse 15 miles to the north. Turbidity from the mudboils has degraded the water quality of Onondaga Creek despite a series of mitigation efforts that began in the early 1990s. Turbidity mitigation actions presently (2025) being considered include creek relocation and offline sediment settling. In support of these proposed actions during 2021–23, the U.S. Geological Survey, in cooperation with the New York State Department of Environmental Conservation, U.S. Environmental Protection Agency, Onondaga Nation, Onondaga Environmental Institute, and Central New York Regional Planning and Development Board, collected and analyzed geologic, hydrologic, geophysical, and geotechnical data to characterize the shallow hydrogeology along four proposed creek-relocation paths and in the proposed offline settling basin area. The investigation indicated that the four proposed creek-relocation paths, two east of Onondaga Creek and two west of Onondaga Creek, are underlain by sediments including muck, alluvium, mudboil deposits, alluvial-fan sand and gravel, and lacustrine fines. The proposed excavations would penetrate partially to fully saturated conditions: generally, the water table is shallow near the creek and deep on the alluvial fans. The shallowest excavation, about 5 feet below land surface, would be near the creek and primarily in alluvium, and the deepest excavation, as much as 30 feet below land surface, would be in the alluvial-fan deposits. Brackish waters would be penetrated by proposed channel excavations on the eastern side of Onondaga Creek in an area downgradient from a potentially leaking historical salt-exploration borehole and near the main mudboil area. Excavation in these areas likely would provide a continuous source of brackish groundwater to the relocated creek. Proposed channel excavations of muck, soft to very soft lacustrine fines, and mudboil-type sediments in mudboil and suspected mudboil areas would pose an excavation and slope stability challenge and would have the greatest potential to create new mudboils. Proposed channel excavations below the water table on the Rattlesnake Gulf and Rainbow Creek alluvial fans would intercept groundwater and make the constructed streambank susceptible to seepage-induced slope instability. The substantial water-level fluctuation in the sediments of both alluvial fans would aggravate the stability condition. In addition, excavation on the Rattlesnake Gulf alluvial fan would have the potential to affect water-supply springs at the toe of the fan. The proposed offline settling basin area is in the northern part of the Rattlesnake Gulf alluvial fan. Natural and man-made diversions of Rattlesnake Gulf have resulted in saturated conditions in the general area of the proposed basin. The proposed offline settling basin would be excavated in, and berms would be constructed on, alluvial-fan deposits and lacustrine fines. In the proposed basin area, the alluvial deposits overlying the lacustrine fines are less than 10 feet thick. Excavation, berm construction, and loading of the saturated, soft to very soft lacustrine fines may be problematic and require soil strengthening.

New York↗
USGS2025

Review: The hydrogeology of critical mineral resources relevant to the energy transition

Attaining the goals of the international treaty on climate change (the Paris Agreement) will greatly increase the demand for the critical minerals required to implement clean-energy technologies. This poses both challenges and opportunities to the hydrogeologic community from several perspectives. Here, important insights that the hydrogeological sciences have to offer for mineral exploration, mineral production, and addressing environmental issues related to mining and mine decommissioning are summarized. This study focuses on copper, cobalt, lithium, and rare earths to represent the broad spectrum of critical minerals and illustrate their relevance by referring to projected demands and production rates. The current understanding of the hydrogeologic processes that form major deposits of these minerals are then summarized. Ore is defined as the naturally occurring material from which minerals of economic value can be extracted, where most ore deposits are the products of complex hydrogeologic couplings between fluid flow, heat transport, solute transport, chemical reactions, and mechanical deformation. Exploration models for the discovery of deeper, hidden deposits are potentially informed by hydrogeologic theory and hydrogeochemical processes. Hydrogeologic understanding and methods are also essential to production and recovery. Longstanding challenges are mine dewatering and (conversely) mine water supply, as well as mineral-extraction practices such as spoil heap leaching and in situ mining. New challenges arise from element extraction from subsurface brines. Finally, the quantity of water use and potential environmental impacts of mining on water quality are at the core of ‘social license’: the approval and acceptance of society to mining activities.

Hydrogeology Journal↗
USGS1997

Application of acoustical methods for estimating water flow and constituent loads in Perdido Bay, Florida

Water flow and quality data were collected from December 1994 to September 1995 to evaluate variations in discharge, water quality, and chemical fluxes (loads) through Perdido Bay, Florida. Data were collected at a cross section parallel to the U.S. Highway 98 bridge. Discharges measured with an acoustic Doppler current profiler (ADCP) and computed from stage-area and velocity ratings varied roughly between + or - 10,000 cubic feet per second during a typical tidal cycle. Large reversals in flow direction occurred rapidly (less than 1 hour), and complete reversals (resulting in near peak net-upstream or downstream discharges) occurred within a few hours of slack water. Observations of simultaneous upstream and downstream flow (bidirectional flow) were quite common in the ADCP measurements, with opposing directions of flow occurring predominantly in vertical layers. Continuous (every 15 minutes) discharge data were computed for the period from August 18, 1995, to September 28, 1995, and filtered daily mean discharge values were computed for the period from August 19 to September 26, 1995. Data were not computed prior to August 18, 1995, either because of missing data or because the velocity rating was poorly defined (because of insufficient data) for the period prior to landfall of hurricane Erin (August 3, 1995). The results of the study indicate that acoustical techniques can yield useful estimates of continuous (instantaneous) discharge in Perdido Bay. Useful estimates of average daily net flow rates can also be obtained, but the accuracy of these estimates will be limited by small rating shifts that introduce bias into the instantaneous values that are used to compute the net flows. Instantaneous loads of total nitrogen ranged from -180 to 220 grams per second for the samples collected during the study, and instantaneous loads of total phosphorous ranged from -10 to 11 grams per second (negative loads indicate net upstream transport). The chloride concentrations from the water samples collected from Perdido Bay indicated a significant amount of mixing of saltwater and freshwater. Mixing effects could greatly reduce the accuracy of estimates of net loads of nutrients or other substances. The study results indicate that acoustical techniques can yield acceptable estimates of instantaneous loads in Perdido Bay. However, estimates of net loads should be interpreted with great caution and may have unacceptably large errors, especially when saltwater and freshwater concentrations differ greatly.

Florida↗
USGS2024

Mafic alkaline magmatism and rare earth element mineralization in the Mojave Desert, California: The Bobcat Hills connection to Mountain Pass

Occurrences of alkaline and carbonatite rocks with high concentrations of rare earth elements (REE) are a defining feature of Precambrian geology in the Mojave Desert of southeastern California. The most economically important occurrence is the carbonatite stock at Mountain Pass, which constitutes the largest REE deposit in the United States. A central scientific goal is to understand the genesis of the carbonatite ore body in the context of widespread REE-rich igneous activity. A swarm of mafic alkaline (shonkinite) dikes has been mapped and sampled at Bobcat Hills, 65 km southeast of the Mountain Pass mine. Whole-rock geochemistry and zircon geochronology demonstrate a clear affinity to the ca. 1.4 Ga Mountain Pass intrusive system. Bobcat Hills dikes have comparably high REE concentrations (La ∼1,000× chondritic) and an error-weighted mean 207 Pb/ 206 Pb zircon crystallization age of 1,426 ± 2 Ma (2 σ ). Unlike the alkaline intrusions at Mountain Pass, which have abundant inherited zircon from Paleoproterozoic basement rocks and crustally influenced oxygen isotope compositions (δ 18 O zircon = 6.5–7.5‰), the Bobcat Hills dikes lack any evidence of crustal assimilation and have oxygen isotope values that overlap a mantle range (Bobcat Hills average δ 18 O zircon = 5.6 ± 0.3‰). The dikes were a high-temperature, early center of mafic alkaline magmatism in the Mojave Desert that serve as a snapshot of melt generation from a spatially extensive, metasomatized mantle source. We propose that modification of the crust over many tens of Myr at Mountain Pass created an environment that favored crustal assimilation and enabled ascent of late-stage, REE-rich carbonatite magmas.

California↗
USGS2024

A methodology to estimate CO2 and energy gas storage resources in depleted conventional gas reservoirs

Depleted hydrocarbon reservoirs are subsurface geological structures capable of sequestering vast quantities of carbon dioxide (CO 2 ) as well as storing other energy gases for later usage, such as natural gas, and potentially hydrogen (H 2 ). Here we outline a methodology to quantify multi-gas storage resources in depleted conventional gas reservoirs for usage in assessments by the United States Geological Survey (USGS) at the scale of sedimentary basins. The methodology consists first of quantifying accessible pore volume in a depleted reservoir for natural gas storage using up to three equations. Input data are derived from commonly reported or estimated reservoir parameters and natural gas production volumes, and equations may be combined in linear models to improve pore volume estimates. Storage estimates from these equations are tested and validated for 31 reservoirs in the Michigan Basin Province, USA that were previously converted to underground gas storage facilities and have known (federally reported) natural gas storage capacities. Secondly, natural gas storage capacities can be transformed via fluid substitution calculations to estimate the storage resources for non-native fluids, applied here for, CO 2 , H 2 , and methane-H 2 blends, accounting for molecule-specific deviations from ideal gas behavior at reservoir pressures and temperatures as well as differing storage efficiencies. Importantly, the storage of non-native fluids may not be appropriate in all depleted gas reservoir settings due to potential risks like leakage, in particular in the case of H 2 storage, requiring additional knowledge of caprock sealing capacity. Given this caveat, we demonstrate the fluid substitution method for natural gas reservoirs of the Northern Niagaran Reef and Southern Niagaran Reef USGS plays in the Michigan Basin Province, as these trends of Silurian pinnacle reefs are capped with tight-sealing evaporite facies. The deterministic equations outlined from this methodology can be incorporated into future probabilistic USGS gas storage assessments for CO 2 , H 2 , and natural gas resources in the United States.

Michigan↗
USGS2025

Synergy between geology and geophysics in graphite mineral resource assessment

Graphite is designated as a critical mineral by the U.S. Government due to its essential role in modern technology and its vulnerability to supply chain disruption. To evaluate domestic graphite resources, the U.S. Geological Survey (USGS) conducted two airborne electromagnetic (AEM) surveys as part of the Earth Mapping Resources Initiative (Earth MRI) over prospective areas in the southern Appalachians of Alabama and the Seward Peninsula of Alaska. These surveys aimed to refine areas of interest by revealing subsurface electrical resistivity patterns indicative of graphite-bearing rocks. The results of the AEM surveys were integrated with existing geological knowledge and supplemented by field observations to assess the likelihood of undiscovered resources in these regions. This multidisciplinary approach combined geophysical techniques with traditional geological methods, enhancing the understanding of graphite potential in areas that may have been previously overlooked. The findings from this initiative are expected to contribute significantly to the ongoing efforts to secure a reliable domestic supply of graphite, thereby reducing import reliance and supporting national interests in mineral resource management.

Conference Paper↗
USGS2025

Nanometer-scale relationships between sedimentary organic matter molecular composition, fluorescence, cathodoluminescence, and reflectance: The importance of oxygen content at low thermal maturities

Molecular characterization of sedimentary organic matter (SOM), termed macerals, is a common goal when seeking to understand petroleum generation as well as other geologic processes in deep time. However, unambiguous measurement of discrete macerals is challenging due to the small size of organic particles in sedimentary rocks, the proximity of different organic matter types to one another, mineral-organic matter interactions, and maceral mixing that occurs during SOM isolation prior to ex situ analysis. The recent advent of infrared spectrometers capable of nanometer-scale resolution and the application of these technologies to geologic samples has enabled advances in rapid, in situ molecular characterization of SOM allowing for insights into paleoenvironmental processes, such as organic matter productivity and preservation, among others. Here we employ one such technology, optical photothermal infrared (OPTIR) spectroscopy, to map SOM functional group distributions at 500-nm resolution in a sample from the Lower Cretaceous Sunniland Limestone of the South Florida Basin. Examined fields of view include occurrences of amorphous organic matter (AOM), inertinite, micrinite, solid bitumen, telalginite, and vitrinite. OPTIR data from these macerals are compared against traditional organic petrographic data from the same organic grains including fluorescence intensity and white light reflectance as well as against cathodoluminescence response, an emerging organic petrographic approach. Maceral oxygen content (using carbonyl functional group abundance as a proxy) is observed to vary widely between maceral types but correlates strongly with fluorescence and cathodoluminescence intensity as well as against reflectance. These findings highlight the important role that oxygen content plays in determining the optical properties of SOM and further demonstrate the ability of OPTIR to discriminate subtle molecular differences between SOM types.

Organic Geochemistry↗
USGS2025

Simulation of groundwater flow in Wake County, North Carolina, 2000 through 2070

In 2019, the U.S. Geological Survey and Wake County Environmental Services began a collaborative study to evaluate groundwater resources and long-term groundwater availability in the county’s fractured-rock groundwater system. Wake County, in central North Carolina, is experiencing rapid population growth, associated land development, and changing water use. Hydrogeologic data including groundwater levels, aquifer testing, borehole fracture flow measurements, water-quality samples, and groundwater age-dating tracers were collected, along with findings from previous investigations, to help inform a conceptual model of the flow system used to develop a modular three-dimensional finite-difference groundwater-flow model (MODFLOW) for simulating historical and future groundwater conditions from 2000 to 2070. Hydraulic conductivity and transmissivity ranges were estimated from 17 slug tests and 21 borehole-flow measurements. Groundwater-quality analytical results from 19 sampling sites indicate that oxidation-reduction (redox) conditions varied within the regolith and bedrock and that minimal evaporation occurred before recharge entered the groundwater system. Age dating revealed mixtures of older and younger water, ranging from the 1940s to the 1990s—indicating variable flow pathways of recharge within permeable bedrock fracture zones. To simplify the complex fractured-rock groundwater system, two layers representing the regolith and the fractured bedrock were used in the MODFLOW model. Model calibration included parameter estimation and provided a reasonable fit to observed groundwater levels and estimated stream base flows. The model forecast scenarios incorporated future climate-model data for two emissions scenarios with land cover change projections to simulate potential impacts to future groundwater levels, recharge, and base flows. Recharge and base flow projections were largely within historical ranges, with no apparent long-term trends, but did indicate a slight downward shift in median values—likely, in part, because of differences in spatial resolution of input climate datasets. Seasonal patterns were consistent with historical data, with projections of possible increases in future winter recharge. Model limitations are discussed, and additional monitoring and model refinement needs are highlighted to support decision making for local groundwater management.

North Carolina↗
USGS2024

Effective site coefficients for the 2024 International Building Code (IBC)

The U.S. National Seismic Hazard Models (NSHMs), developed by the U.S. Geological Survey (USGS), have long been the scientific foundation of seismic design guidelines and have been used to compute design ground motions for construction of new buildings and retrofit of existing buildings in the United States and its territories. The 2018 NSHM is adopted by the 2024 International Building Code (IBC). Prior to the 2018 NSHM update, hazard calculations were required only at one reference site condition defined by V S30 =760 m/s (where V S30 is the time-averaged shear wave velocity from the surface to a depth of 30 m) and three periods (peak ground acceleration, PGA, and pseudo spectral accelerations at periods of 0.2 and 1 s, S s and S 1 ). Site coefficients, F PGA , F a , and F v , were then defined by the Building Seismic Safety Council (BSSC) Provisions Update Committee (PUC) in the site-specific procedures of National Earthquake Hazard Reduction Program (NEHRP) Recommended Seismic Provisions to calculate ground motions for other site classes with different V S30 values at the given periods. The design ground motions at other periods were then estimated using a generic spectral shape that was also defined by the BSSC PUC in NEHRP provisions. In recent years, the engineering community has realized there were deficiencies with the F a and F v site coefficients and the generic spectral shape. To avoid potentially dangerous underestimations of design ground motions for long period structures on soft site conditions in high seismicity regions, the BSSC PUC recommended the use of multi-period response spectra (MPRS) in 2017. As a result, the USGS produced multi-period and multi-V S30 response spectral values in the 2018 NSHM for calculations of design ground motions and the site coefficients F a and F v were eliminated from the 2020 NEHRP Provisions. As these site coefficients were widely used inside and outside of the United States, in this study we back-calculate the “effective” site coefficients F a,eff , and F v,eff by comparing MPRS for various site classes with the MPRS for the reference site condition, and discuss the changes that are observed in the 2024 IBC compared to its previous version in 2021. The effective site coefficients are presented for test site locations and their dependence on various factors including period, ground motion intensity, and regional models are discussed. Ratio maps between the new effective site coefficients and the old ones are then presented for soft site classes and for short and long periods. For soft site classes at short periods, the new effective site coefficients are lower than the old site coefficients for high seismicity regions and higher for low seismicity regions. As it was expected, for soft site classes at long periods and high seismicity regions, the new effective site coefficients are much larger than the old site coefficients without imposing the 50% increase as a penalty that was suggested in the 2021 IBC, whereas they could be much smaller if the 50% increase would have been imposed particularly around New Madrid and Charleston high seismicity regions. For low seismicity regions, the long period effective site coefficients can be smaller or larger by 20% compared to the 2021 IBC coefficients.

Conference Paper↗
USGS1977

Summary of results from electromagnetic and galvanic soundings on Kilauea Iki lava lake, Hawaii

The purpose of this report is to summarize various electrical sounding studies made on the Kilauea Iki lava lake and to present some of the preliminary interpretations that resulted from the measurements. The following discussion is not intended as a complete interpretation, but is intended to summarize the major points made in an invited oral presentation at the American Geophysical Union fall meeting held in San Francisco, Calif. on December 6, 1976. This paper was part of a group of papers dealing with various geophysical studies recently made on the Kilauea Iki lava lake. A general plan map of Kilauea Iki lava lake is shown in figure 1. Electromagnetic (EM) loop-loop soundings, D.C. resistivity soundings, and VLF apparent resistivity measurements were made on the lave lake surface. All of these surveys were made to determine the geoelectric structure of the lava lake and to determine parameters of the molten basaltic lens that exist in the partially solidified lava lake.

Hawaii↗
USGS2025

Aquifer storage change and storage properties, Rio Rancho, New Mexico, 2019–23

To better understand changes in groundwater storage and groundwater elevations, the U.S. Geological Survey, in cooperation with the City of Rio Rancho, New Mexico, carried out a multiyear groundwater monitoring project. Groundwater-level data were collected at 27 locations, including sites having multiple wells screened at different depths and those having long-term records. A repeat microgravity network of 20 stations was established, and surveys were carried out three times per year. The microgravity method provides a direct, quantitative measurement of mass change caused by aquifer filling or draining. Data collected during the 2019–23 study period indicate generally stable groundwater conditions, with small fluctuations in groundwater levels (increasing at some wells, declining at others), and small declines in groundwater storage over the period of record at most gravity locations (average = −0.33 foot of water per year). The discrepancy between the water-level and microgravity data may have been caused by a loss of soil moisture in the unsaturated zone, which is as much as 1,000 feet thick in some areas. At the Rio Rancho Advanced Water Treatment Facility, where the city recharges water through direct injection, there may be seasonal correlations in storage related to injection but no longer-term accumulation of recharged water in the immediate vicinity of the facility, indicating water is moving efficiently into the aquifer.

New Mexico↗
USGS2024

The 2023 Alaska National Seismic Hazard Model

US Geological Survey (USGS) National Seismic Hazard Models (NSHMs) are used extensively for seismic design regulations in the United States and earthquake scenario development, as well as risk assessment and mitigation for both buildings and infrastructure. This 2023 update of the long-term, time-independent Alaska NSHM includes substantial changes to both the earthquake rupture forecast (ERF) and ground motion models (GMMs). The ERF includes numerous additions to the finite-fault model, considers two deformation models, and introduces updated declustering and smoothing algorithms in the gridded background seismicity model. For the Alaska–Aleutian subduction zone, megathrust earthquakes occur on an updated structural and segmentation model, and the moment magnitude (M) 8+ rupture and rate model include a logic tree branch that considers slip rates derived from geodetic models of interface coupling. The megathrust model considers multiple models of down-dip width, and magnitudes are computed using newly developed scaling relations. For subduction intraslab events and subduction interface events with M < 7, the 2023 update uses a smoothed seismicity model with rupture depths derived from Slab2. The 2023 model updates GMMs in all tectonic settings using the recently published Next Generation Attenuation Subduction (NGA-Sub) GMMs for subduction interface and intraslab events, and the NGA-West2 GMMs for active crustal settings. Collectively, additions and updates to the Alaska NSHM result in hazard increases across most of south-central Alaska relative to the previous model, published in 2007. These changes are primarily due to the adoption of updated rate models for the large-magnitude interface events and the NGA-Sub GMMs that have much higher aleatory variability (sigma), consistent with global observations, and that include models of epistemic uncertainty.

Alaska↗
USGS2026

Scenarios to assess the future water availability in the Mississippi River Valley Alluvial Aquifer for the Cache River and Grand Prairie Regions of Arkansas

The U.S. Geological Survey, as part of the Arkansas Groundwater Initiative, developed forecast scenarios using previously calibrated MODFLOW 6 groundwater models that focused on the Cache and Grand Prairie Critical Groundwater Areas to assess the impact of future climate and water management strategies on the Mississippi River Valley alluvial aquifer. A Soil Water Balance model was used to forecast recharge and irrigation water use. The forecast scenario period was from January 1, 2019, through December 31, 2055, with monthly stress periods. Twenty scenarios were simulated and included seven alternate climate forecasts, five 13 general groundwater pumping reduction scenarios (round 1), and groundwater pumping reduction scenarios by crop type and for the Bayou Meto Water Management Project and Grand Prairie Area Demonstration Project (round 2). Declines in saturated thickness within the Cache Critical Groundwater Area were larger for 18 of the 20 scenarios as compared to outside of the Critical Groundwater Area. The largest average increase in saturated thickness inside the Critical Groundwater Area was 6.4 m which occurred for the round 1, 50 percent reduction scenario. Automatic reductions in groundwater pumping by MODFLOW 6 in the Cache simulation ranged from 0.02 to 13.1 percent of total groundwater pumping. For the Grand Prairie model domain, the average change in saturated thickness of the Mississippi River Valley alluvial aquifer inside the Critical Groundwater Area for the forecast period ranged between -6.6 to 1.7 m. The average saturated thickness of the Mississippi River Valley alluvial aquifer inside the Grand Prairie Critical Groundwater Area declined for 16 of the 20 scenarios. The average reduction in requested groundwater pumping for all scenarios inside the Grand Prairie Critical Groundwater Area was 25.1 percent, and the largest reduction was 46.5 percent.

ESS Open Archive↗
USGS2025

The 3D Elevation Program—Supporting the economy of Massachusetts

Introduction Massachusetts extends from the mountains of the Appalachian system in the west of the State to the sandy beaches and rocky shorelines of the Atlantic coast in the east. Inland topographic data support a wide range of important activities, including geologic mapping, transportation planning, forest and wildlife management, quantifying ecological services, water supply protection, commonwealth-wide infrastructure planning, local site planning, and flood-plain management. Nearshore bathymetry can be used to support coastal portions of the Commonwealth by addressing the combined threats of ocean warming, strong storm surge, and rising sea levels. The maintenance and (or) expansion of Massachusetts ports (for instance, Boston, New Bedford) and Cape Cod sediment management depends upon the accurate mapping of bathymetry and the frequent influx of sediment and redeposition. Critical applications that address the broad range of requirements depend on light detection and ranging (lidar) data that provide a highly detailed three-dimensional (3D) model of the Earth’s surface and aboveground features. The 3D Elevation Program (3DEP) is managed by the U.S. Geological Survey (USGS) in partnership with Federal, State, Tribal, U.S. territorial, and local agencies to acquire consistent lidar coverage at quality level 2 or better to meet the many needs of the Nation and Massachusetts. The status of available and in-progress 3DEP baseline lidar data in Massachusetts is shown in figure 1. 3DEP baseline lidar data include quality level 2 or better, 1-meter or better digital elevation models, and lidar point clouds, and must meet the Lidar Base Specification version 1.2 ( https://www.usgs.gov/3dep/lidarspec ) or newer requirements. The National Enhanced Elevation Assessment identified user requirements and conservatively estimated that availability of lidar data would result in at least $1.23 million in new benefits annually to Massachusetts. The top 10 Massachusetts business uses for 3D elevation data, which are based on the estimated annual conservative benefits of 3DEP, are shown in table 2.

Massachusetts↗
USGS2025

Relationship between peak and cumulative ground motions from 49 Mw 3-6 earthquakes in the San Francisco Bay Area

We examine the relationship between peak ground velocity (PGV) and cumulative absolute displacement (CAD) for 49 M w 3 – 6 earthquakes in the San Francisco Bay Area (SFBA) and gain insight into the spatiotemporal partitioning of seismic energy in ground motion records with respect to source, path, and site effects. PGV and CAD are positively correlated, but there can be large deviations from the average trend. For example, ground motion records with either very long duration resonance or short pulse-like motions will have higher or lower CAD, respectively, but could have very similar PGV. We perform principal component analysis (PCA) on PGV-CAD for >7000 records in the SFBA with the goal of investigating what influences positive or negative anomalies in cumulative motions. PCA rotates the PGV-CAD datapoints into two principal components, where the one with the larger variance, which we call the “primary intensity” represents mostly the distance-dependence of ground motion amplitudes. The other principal component, which we call the “excess motion”, represents the deviation from cumulative motions that would be typical for a ground motion record with a given PGV. The excess motion will be positive in the case of records with long duration ringing and will be negative for short duration pulse-like ground motions. We find that excess motion is generally positive at sites in sedimentary basins and in soft sediments around the SF Bay. Excess motion is generally negative in the very near field, as well as at sites on hard bedrock. We discuss the findings here in terms of implications for seismic hazard applications and other wave propagation phenomena.

California↗
USGS2023

Eruptive history within the vicinity of Al Madīnah in northern Harrat Rahat, Kingdom of Saudi Arabia

The northernmost part of the Harrat Rahat volcanic field contains early Pleistocene to Holocene mafic eruptive products within the vicinity of the city of Al Madīnah, Kingdom of Saudi Arabia. A detailed geologic investigation into the eruptive history of a 570 square kilometer (km 2 ) area covering Al Madīnah and the surrounding area has yielded 33 mapped Quaternary volcanic units consisting of lava flows, scoria cones, and shield volcanoes. These eruptive products consist of continental, intraplate alkalic and minor transitional basalts, hawaiites, and a single mugearite that were emplaced from at least 1,014±14 thousand years ago (ka) to a single Holocene eruption in 1256 C.E. Lava flows are generally 10 to 15 kilometers (km) long (but can reach 23 km long), 1 to 3 km wide, and at least 10 meters thick. Most of the mapped units erupted episodically between 400 and 340 ka and 180 and 100 ka. Despite small individual volumes (less than 1 cubic kilometers dense rock equivalent), each unit represents eruption of a distinct magma batch that was strongly influenced by clinopyroxene, olivine, and plagioclase fractionation. Some of these units are interpreted to have undergone magma mixing pre- and (or) syneruptively. Integrating eruption ages, geochemistry, and paleomagnetic data yields evidence that some eruptions were temporally and (or) spatially clustered. Aligned scoria cones and elongate vent edifices were constructed atop fissure vent systems that reflect the local stress field, which controls dike ascent through the middle and upper crust.

Professional Paper↗
USGS2026

HyFlood: A surrogate-model-based framework for compound coastal flooding

Compound coastal flooding is a major threat to low-lying coastal regions and is expected to intensify under future climate change projections. However, modeling the joint interaction of waves, storm surge, tides, and rainfall remains computationally demanding, limiting the development of fast and reliable forecast tools. Here we present HyFlood, a hybrid statistical-numerical downscaling framework capable of computing and mapping high-resolution compound flood hazards while substantially reducing the computational cost compared with fully process-based hydrodynamic modeling. HyFlood combines statistical sampling and selection algorithms with a cascade of reduced-complexity surrogate models that emulate nearshore wave transformation, surf-zone hydrodynamics, and coastal, fluvial, and pluvial flooding. The surrogate models employ machine-learning and regression algorithms applied to a low-dimensional representation of the flooding outputs, obtained through statistical dimensionality reduction. The framework is demonstrated in southern O'ahu, Hawai'i, a region exposed to elevated sea levels driven by tides, waves, and storm surge along with frequent precipitation-driven flash flooding. Validation of the surrogates against the physics-based model outputs demonstrates that HyFlood accurately reproduces daily maxima of spatially distributed flooding depths. This hybrid approach offers a scalable and efficient tool to better quantify how changes in flooding drivers translate into hazard and impact assessments, and to support compound-flood risk assessments and climate-change adaptation planning.

Hawaii↗
USGS2026

Arsenic and isotope concentrations in the lower Platte River valley of eastern Nebraska, early 1970s to 2023

The City of Lincoln, Nebraska, has been monitoring concentrations of arsenic in their source water and evaluating their options for treatment and removal since at least 2002. In 2022, the City of Lincoln, Nebr., with funding assistance from the Nebraska Water Sustainability Fund, began cooperating with the U.S. Geological Survey to examine arsenic concentrations in surface water and groundwater in the lower Platte River valley and the area around City of Lincoln Water System (LWS) well field. Arsenic data collected from the Platte River since 1974 were examined using the “weighted regression on time, discharge, and season” model, which compared the streamflow (also referred to as “discharge”), time of year, and season to estimate concentrations of arsenic. Annual mean arsenic concentrations modeled for more than 49 years at the Platte River at Louisville, Nebr., U.S. Geological Survey streamgage (station 06805500), indicated a significant increasing trend. Arsenic concentrations in the Platte River were seasonal, with the highest concentrations being observed during mid- to late summer. When seasonal patterns and streamflow were combined with arsenic concentrations in the Platte River during low streamflow conditions, groundwater contributions, which can have higher arsenic concentrations, make up a larger portion of the streamflow. Arsenic samples were collected from upstream rivers in 2022 and 2023 and were paired to analyze the arsenic contributions at the U.S. Geological Survey streamgage on the Platte River near Ashland, Nebr. (station 06801000), near the City of Lincoln well field. The arsenic concentrations from the streamgage on the Platte River near Ashland, Nebr., location, were higher than the U.S. Geological Survey streamgage on the Elkhorn River at Waterloo, Nebr. (station 06800500), and significantly lower than at the U.S. Geological Survey streamgage on the Platte River near Leshara, Nebr.(station 06796500), indicating that the Platte River usually contributes a higher concentration of arsenic than does the Elkhorn River as they join near Ashland, Nebr. During 1991–2023, six groundwater monitoring wells were analyzed to identify trends in arsenic concentrations. Two of the six wells had a positive trend during the 33-year period. One monitoring well did not reveal a long-term trend during this period but showed a trend during 2019–23, correlating to a period when the island in the middle of the Platte River was connected to the east bank of the river when manganese reducing conditions were present and groundwater levels were declining in the well. Across all wells the oxidation and reduction (redox) condition during the time of sampling was assessed. Mixed anoxic and (or) oxic redox condition was the most common redox process and the highest sampled arsenic concentrations in monitoring wells were observed in anoxic conditions driven by manganese reduction. Groundwater arsenic concentrations had seasonal variation around the City of Lincoln well field, with higher arsenic concentrations tending to be further south in comparison to samples collected further north. Isotope samples were collected and analyzed in surface water and groundwater around the LWS well field. The samples indicate that the proportion of surface water present in the LWS production wells can be higher in the spring and lower in the summer. With higher arsenic concentrations observed in the stream water during the summer period, the LWS source water can be affected by these elevated arsenic concentrations even though the proportion of surface water is lower.

Nebraska↗