USGS Science⌕ Search

SEARCH · USGS Science

Results for “The Seismic Record”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56Linked to original sources

Tilts in strong ground motion

Most instruments used in seismological practice to record ground motion are pendulum seismographs, velocigraphs, or accelerographs. In most cases it is assumed that seismic instruments are only sensitive to the translational motion of the instrument's base. In this study the full equation of pendulum motion, including the inputs of rotations and tilts, is considered. It is shown that tilting the accelerograph's base can severely impact its response to the ground motion. The method of tilt evaluation using uncorrected strong-motion accelerograms was first suggested by Graizer (1989), and later tested in several laboratory experiments with different strong-motion instruments. The method is based on the difference in the tilt sensitivity of the horizontal and vertical pendulums. The method was applied to many of the strongest records of the Mw 6.7 Northridge earthquake of 1994. Examples are shown when relatively large tilts of up to a few degrees occurred during strong earthquake ground motion. Residual tilt extracted from the strong-motion record at the Pacoima Dam-Upper Left Abutment reached 3.1?? in N45??E direction, and was a result of local earthquake-induced tilting due to high-amplitude shaking. This value is in agreement with the residual tilt measured by using electronic level a few days after the earthquake. The method was applied to the building records from the Northridge earthquake. According to the estimates, residual tilt reached 2.6?? on the ground floor of the 12-story Hotel in Ventura. Processing of most of the strongest records of the Northridge earthquake shows that tilts, if happened, were within the error of the method, or less than about 0.5??.

Bulletin of the Seismological Society of America↗

Seismicity at Fuego, Pacaya, Izalco, and San Cristobal Volcanoes, Central America, 1973-1974

Seismic data collected at four volcanoes in Central America during 1973 and 1974 indicate three sources of seismicity: regional earthquakes with hypocentral distances greater than 80 km, earthquakes within 40 km of each volcano, and seismic activity originating at the volcanoes due to eruptive processes. Regional earthquakes generated by the underthrusting and subduction of the Cocos Plate beneath the Caribbean Plate are the most prominent seismic feature in Central America. Earthquakes in the vicinity of the volcanoes occur on faults that appear to be related to volcano formation. Faulting near Fuego and Pacaya volcanoes in Guatemala is more complex due to motion on a major E-W striking transform plate boundary 40 km north of the volcanoes. Volcanic activity produces different kinds of seismic signatures. Shallow tectonic or A-type events originate on nearby faults and occur both singly and in swarms. There are typically from 0 to 6 A-type events per day with b value of about 1.3. At very shallow depths beneath Pacaya, Izalco, and San Cristobal large numbers of low-frequency or B-type events are recorded with predominant frequencies between 2.5 and 4.5 Hz and with b values of 1.7 to 2.9. The relative number of B-type events appears to be related to the eruptive states of the volcanoes; the more active volcanoes have higher levels of seismicity. At Fuego Volcano, however, low-frequency events have unusually long codas and appear to be similar to tremor. High-amplitude volcanic tremor is recorded at Fuego, Pacaya, and San Cristobal during eruptive periods. Large explosion earthquakes at Fuego are well recorded at five stations and yield information on near-surface seismic wave velocities (??=3.0??0.2 km/sec.). ?? 1983 Intern. Association of Volcanology and Chemistry of the Earth's Interior.

Bulletin Volcanologique↗

A possible source mechanism of the 1946 Unimak Alaska far-field tsunami, uplift of the mid-slope terrace above a splay fault zone

In 1946, megathrust seismicity along the Unimak segment of the Alaska subduction zone generated the largest ever recorded Alaska/Aleutian tsunami. The tsunami severely damaged Pacific islands and coastal areas from Alaska to Antarctica. It is the charter member of “tsunami” earthquakes that produce outsized far-field tsunamis for the recorded magnitude. Its source mechanisms were unconstrained by observations because geophysical data for the Unimak segment were sparse and of low resolution. Reprocessing of legacy geophysical data reveals a deep water, high-angle reverse or splay thrust fault zone that leads megathrust slip upward to the mid-slope terrace seafloor rather than along the plate boundary toward the trench axis. Splay fault uplift elevates the outer mid-slope terrace and its inner area subsides. Multibeam bathymetry along the splay fault zone shows recent but undated seafloor disruption. The structural configuration of the nearby Semidi segment is similar to that of the Unimak segment, portending generation of a future large tsunami directed toward the US West coast.

Alaska↗

Character and distribution of exposed glaciodeltaic deposits off outer Cape Cod, Massachusetts, and their effects on hydrogeology and benthic habitats

Seabed outcrops of glaciodeltaic sediments were identified in four places east of Cape Cod, Massachusetts, during seismic-reflection, multibeam bathymetric and backscatter, bottom photographic, and sediment sampling surveys. These strata record coarser-grained ice-proximal glaciofluvial topset to finer-grained distal glaciolacustrine bottomset deposition within deltaic systems that prograded southwestward into glacial lakes from the South Channel lobe about 18 ka B.P. These beds are important because they (1) influence the outer Cape's hydrogeologic framework, and (2) constitute relatively stable, locally rough habitats within an area of seafloor dominated by mobile sand and gravelly sediment, and benefit the benthic fauna by providing shelter and a substrate amenable to burrow construction. ?? Springer-Verlag 2006.

Massachusetts↗

Infrasonic tremor observed at Kilauea Volcano, Hawai'i

[1] Infrasonic array data collected at Kīlauea Volcano, Hawai'i, during November 12–21, 2002 indicate that the active vents and lava tube system near the Pu'u 'Ō'ō vent complex emit almost continuous infrasound in the 0.3–10 Hz frequency band. The spectral content of these infrasonic signals matches well that of synchronous seismic tremor. In sites protected from wind noise, significant signal to noise ratios were recorded as far as ∼13 km from the crater of Pu'u 'Ō'ō. The infrasonic recordings suggest that one or more tremor sources may be close to the surface. In addition, these results demonstrate that adequate site and instrument selections for infrasonic arrays are essential in order to obtain consistent and reliable infrasonic detections.

Hawai'i↗

Deep low-frequency earthquakes in tremor localize to the plate interface in multiple subduction zones

Deep tremor under Shikoku, Japan, consists primarily, and perhaps entirely, of swarms of low-frequency earthquakes (LFEs) that occur as shear slip on the plate interface . Although tremor is observed at other plate boundaries, the lack of cataloged low-frequency earthquakes has precluded a similar conclusion about tremor in those locales. We use a network autocorrelation approach to detect and locate LFEs within tremor recorded at three subduction zones characterized by different thermal structures and levels of interplate seismicity: southwest Japan, northern Cascadia, and Costa Rica. In each case we find that LFEs are the primary constituent of tremor and that they locate on the deep continuation of the plate boundary. This suggests that tremor in these regions shares a common mechanism and that temperature is not the primary control on such activity.

Geophysical Research Letters↗

The 12 November 2017 Mw 7.3 Ezgeleh–Sarpolzahab (Iran) earthquake and active tectonics of the Lurestan arc

The 12 November 2017 M w 7.3 Ezgeleh‐Sarpolzahab earthquake is the largest instrumentally recorded earthquake in the Zagros Simply Folded Belt by a factor of ∼10 in seismic moment. Exploiting local, regional, and teleseismic data and synthetic aperture radar interferometry imagery, we characterize the rupture, its aftershock sequence, background seismicity, and regional tectonics. The mainshock ruptured slowly (∼2 km/s), unilaterally southward, for ∼40 km along an oblique (dextral‐thrust) fault that dips ∼14°E beneath the northwestern Lurestan arc. Slip is confined to basement depths of ∼12–18 km, resolvably beneath the sedimentary cover which is ∼8 km thick in this area. The gentle dip angle and basement location allow for a broad slip area, explaining the large magnitude relative to earthquakes in the main Fars arc of the Zagros, where shallower, steeper faults are limited in rupture extent by weak sedimentary layers. Early aftershocks concentrate around the southern and western edges of the mainshock slip area and therefore cluster in the direction of rupture propagation, implying a contribution from dynamic triggering. A cluster of events ∼100 km to the south near Mandali (Iraq) reactivated the ∼50° dipping Zagros Foredeep Fault. The basement fault responsible for the Ezgeleh‐Sarpolzahab earthquake probably accounts for the ∼1 km elevation contrast between the Lurestan arc and the Kirkuk embayment but is distinct from sections of the Mountain Front Fault that define frontal escarpments elsewhere in the Zagros. It may be related to a seismic interface underlying the central and southern Lurestan arc, and a key concern is whether or not the more extensive regional structure is also seismogenic.

Journal of Geophysical Research: Solid Earth↗

Refinements to the method of epicentral location based on surface waves from ambient seismic noise: introducing Love waves

The purpose of this study is to develop and test a modification to a previous method of regional seismic event location based on Empirical Green’s Functions (EGFs) produced from ambient seismic noise. Elastic EGFs between pairs of seismic stations are determined by cross-correlating long ambient noise time-series recorded at the two stations. The EGFs principally contain Rayleigh- and Love-wave energy on the vertical and transverse components, respectively, and we utilize these signals between about 5 and 12 s period. The previous method, based exclusively on Rayleigh waves, may yield biased epicentral locations for certain event types with hypocentral depths between 2 and 5 km. Here we present theoretical arguments that show how Love waves can be introduced to reduce or potentially eliminate the bias. We also present applications of Rayleigh- and Love-wave EGFs to locate 10 reference events in the western United States. The separate Rayleigh and Love epicentral locations and the joint locations using a combination of the two waves agree to within 1 km distance, on average, but confidence ellipses are smallest when both types of waves are used.

Geophysical Journal International↗

Influence of lithostatic stress on earthquake stress drops in North America

We estimate stress drops for earthquakes in and near the continental United States using the method of spectral ratios. The ratio of acceleration spectra between collocated earthquakes recorded at a given station removes the effects of path and recording site and yields source parameters including corner frequency for, and the ratio of seismic moment between, the two earthquakes. We determine stress drop from these parameters for 1121 earthquakes greater than M ∼3 in 60 earthquake clusters. We find that the average Brune stress drop for the few eastern United States (EUS) tectonic mainshocks studied (2.6–36 MPa) is about three times greater than that of tectonic mainshocks in the western United States (WUS, 1.0–7.9 MPa) and five times greater than mainshocks potentially induced by wastewater injection in the central United States (CUS, 0.6–5.6 MPa). EUS events tend to be deeper thrusting events, whereas WUS events tend to be shallower but have a wide range of focal mechanisms. CUS events tend to be shallow with strike‐slip to normal‐faulting mechanisms. With the possible exception of CUS aftershocks, we find that differences in stress drop among all events can be taken into account, within one standard deviation of significance, by differences in the shear failure stress as outlined by Mohr–Coulomb theory. The shear failure stress is a function of vertical stress (or depth), the fault style (normal, strike slip, or reverse), and coefficient of friction (estimated here to be, on average, 0.64). After accounting for faulting style and depth dependence, we find that the average Brune stress drop is about 3% of the failure stress. These results suggest that high‐frequency shaking hazard (>∼1 Hz) from shallow induced events and aftershocks is reduced to some extent by lower stress drop. However, the shallow hypocenters will increase hazard within several kilometers of the source.

Bulletin of the Seismological Society of America↗

Puerto Rico seismic program seismological data report, August 16, 1974-June 30, 1975

The purpose of this data report is to collect and distribute preliminary data acquired from a network of seismic stations on Puerto Rico in order to facilitate current studies of earthquake occurrence. Record interpretation, data processing, and collation of hypocenter data and related event parameters are performed by the U.S. Geological Survey, Golden, Colorado. This compilation Is preliminary and is subject to later revision on the basis of current research.

Open-File Report↗

Hydrogeology and water quality of the stratified-drift aquifer in the Pony Hollow Creek Valley, Tompkins County, New York

The lithology, areal extent, and the water-table configuration in stratified-drift aquifers in the northern part of the Pony Hollow Creek valley in the Town of Newfield, New York, were mapped as part of an ongoing aquifer mapping program in Tompkins County. Surficial geologic and soil maps, well and test-boring records, light detection and ranging (lidar) data, water-level measurements, and passive-seismic surveys were used to map the aquifer geometry, construct geologic sections, and determine the depth to bedrock at selected locations throughout the valley. Additionally, water-quality samples were collected from selected streams and wells to characterize the quality of surface and groundwater in the study area. Sedimentary bedrock underlies the study area and is overlain by unstratified drift (till), stratified drift (glaciolacustrine and glaciofluvial deposits), and recent post glacial alluvium. The major type of unconsolidated, water-yielding material in the study area is stratified drift, which consists of glaciofluvial sand and gravel, and is present in sufficient amounts in most places to form an extensive unconfined aquifer throughout the study area, which is the source of water for most residents, farms, and businesses in the valleys. A map of the water table in the unconfined aquifer was constructed by using (1) measurements made between the mid-1960s through 2010, (2) control on the altitudes of perennial streams at 10-foot contour intervals from lidar data collected by Tompkins County, and (3) water surfaces of ponds and wetlands that are hydraulically connected to the unconfined aquifer. Water-table contours indicate that the direction of groundwater flow within the stratified-drift aquifer is predominantly from the valley walls toward the streams and ponds in the central part of the valley where groundwater then flows southwestward (down valley) toward the confluence with the Cayuta Creek valley. Locally, the direction of groundwater flow is radially away from groundwater mounds that have formed beneath upland tributaries that lose water where they flow on alluvial fans on the margins of the valley. In some places, groundwater that would normally flow toward streams is intercepted by pumping wells. Surface-water samples were collected in 2001 at four sites including Carter, Pony Hollow (two sites), and Chafee Creeks, and from six wells throughout the aquifer. Calcium dominates the cation composition and bicarbonate dominates the anion composition in groundwater and surface-water samples and none of the common inorganic constituents collected exceeded any Federal or State water-quality standards. Groundwater samples were collected from six wells all completed in the unconfined sand and gravel aquifer. Concentrations of calcium and magnesium dominated the ionic composition of the groundwater in all wells sampled. Nitrate, orthophosphate, and trace metals were detected in all groundwater samples, but none were more than U.S. Environmental Protection Agency or New York State Department of Health regulatory limits.

New York↗

Source processes of industrially-induced earthquakes at the Geysers geothermal area, California

Microearthquake activity at The Geysers geothermal area, California, mirrors the steam production rate, suggesting that the earthquakes are industrially induced. A 15-station network of digital, three-component seismic stations was operated for one month in 1991, and 3,900 earthquakes were recorded. Highly-accurate moment tensors were derived for 30 of the best recorded earthquakes by tracing rays through tomographically derived 3-D VP and VP / VS structures, and inverting P-and S-wave polarities and amplitude ratios. The orientations of the P-and T-axes are very scattered, suggesting that there is no strong, systematic deviatoric stress field in the reservoir, which could explain why the earthquakes are not large. Most of the events had significant non-double-couple (non-DC) components in their source mechanisms with volumetric components up to ???30% of the total moment. Explosive and implosive sources were observed in approximately equal numbers, and must be caused by cavity creation (or expansion) and collapse. It is likely that there is a causal relationship between these processes and fluid reinjection and steam withdrawal. Compensated linear vector dipole (CLVD) components were up to 100% of the deviatoric component. Combinations of opening cracks and shear faults cannot explain all the observations, and rapid fluid flow may also be involved. The pattern of non-DC failure at The Geysers contrasts with that of the Hengill-Grensdalur area in Iceland, a largely unexploited water-dominated field in an extensional stress regime. These differences are poorly understood but may be linked to the contrasting regional stress regimes and the industrial exploitation at The Geysers.

Geophysics↗

Seismic joint analysis for non-destructive testing of asphalt and concrete slabs

A seismic approach is used to estimate the thickness and elastic stiffness constants of asphalt or concrete slabs. The overall concept of the approach utilizes the robustness of the multichannel seismic method. A multichannel-equivalent data set is compiled from multiple time series recorded from multiple hammer impacts at progressively different offsets from a fixed receiver. This multichannel simulation with one receiver (MSOR) replaces the true multichannel recording in a cost-effective and convenient manner. A recorded data set is first processed to evaluate the shear wave velocity through a wave field transformation, normally used in the multichannel analysis of surface waves (MASW) method, followed by a Lambwave inversion. Then, the same data set is used to evaluate compression wave velocity from a combined processing of the first-arrival picking and a linear regression. Finally, the amplitude spectra of the time series are used to evaluate the thickness by following the concepts utilized in the Impact Echo (IE) method. Due to the powerful signal extraction capabilities ensured by the multichannel processing schemes used, the entire procedure for all three evaluations can be fully automated and results can be obtained directly in the field. A field data set is used to demonstrate the proposed approach.

Conference Paper↗

Geomorphology, active tectonics, and landscape evolution in the Mid-Atlantic region

In 2014, the geomorphology community marked the 125th birthday of one of its most influential papers, “The Rivers and Valleys of Pennsylvania” by William Morris Davis. Inspired by Davis’s work, the Appalachian landscape rapidly became fertile ground for the development and testing of several grand landscape evolution paradigms, culminating with John Hack’s dynamic equilibrium in 1960. As part of the 2015 GSA Annual Meeting, the Geomorphology, Active Tectonics, and Landscape Evolution field trip offers an excellent venue for exploring Appalachian geomorphology through the lens of the Appalachian landscape, leveraging exciting research by a new generation of process-oriented geomorphologists and geologic field mapping. Important geomorphologic scholarship has recently used the Appalachian landscape as the testing ground for ideas on long- and short-term erosion, dynamic topography, glacial-isostatic adjustments, active tectonics in an intraplate setting, river incision, periglacial processes, and soil-saprolite formation. This field trip explores a geologic and geomorphic transect of the mid-Atlantic margin, starting in the Blue Ridge of Virginia and proceeding to the east across the Piedmont to the Coastal Plain. The emphasis here will not only be on the geomorphology, but also the underlying geology that establishes the template and foundation upon which surface processes have etched out the familiar Appalachian landscape. The first day focuses on new and published work that highlights Cenozoic sedimentary deposits, soils, paleosols, and geomorphic markers (terraces and knickpoints) that are being used to reconstruct a late Cenozoic history of erosion, deposition, climate change, and active tectonics. The second day is similarly devoted to new and published work documenting the fluvial geomorphic response to active tectonics in the Central Virginia seismic zone (CVSZ), site of the 2011 M 5.8 Mineral earthquake and the integrated record of Appalachian erosion preserved on the Coastal Plain. The trip concludes on Day 3, joining the Kirk Bryan Field Trip at Great Falls, Virginia/ Maryland, to explore and discuss the dramatic processes of base-level fall, fluvial incision, and knickpoint retreat.

Virginia↗

Computers at the Albuquerque Seismological Laboratory

The Worldwide Standardized Seismograph Network (WWSSN) is managed by the U.S Geological Survey in Albuquerque, N. Mex. It consists of a global network of seismographs housed in seismic observatories throughout the world. An important recent addition to this network are the Seismic Research Observatories (SRO) which combine a borehole seismometer with a modern digital data recording system.

Earthquake Information Bulletin (USGS)↗

Micropaleontologic record of Quaternary paleoenvironments in the Central Albemarle Embayment, North Carolina, U.S.A.

To understand the temporal and spatial variation of eustatic sea-level fluctuations, glacio–hydro–isostacy, tectonics, subsidence, geologic environments and sedimentation patterns for the Quaternary of a passive continental margin, a nearly complete stratigraphic record that is fully integrated with a three dimensional chronostratigraphic framework, and paleoenvironmental information are necessary. The Albemarle Embayment, a Cenozoic regional depositional basin in eastern North Carolina located on the southeast Atlantic coast of the USA, is an ideal setting to unravel these dynamic, interrelated processes. Micropaleontological data, coupled with sedimentologic, chronostratigraphic and seismic data provide the bases for detailed interpretations of paleoenvironmental evolution and paleoclimates in the 90 m thick Quaternary record of the Albemarle Embayment. The data presented here come from a transect of cores drilled through a barrier island complex in the central Albemarle Embayment. This area sits in a ramp-like setting between late Pleistocene incised valleys. The data document the episodic infilling of the Albemarle Embayment throughout the Quaternary as a series of transgressive–regressive (T–R) cycles, characterized by inner shelf, midshelf, and shoreface assemblages, that overlie remnants of fluvial to estuarine valley-fill. Barrier island and marginal marine deposits have a low preservation potential. Inner to mid-shelf deposits of the early Pleistocene are overlain by similar middle Pleistocene shelf sediments in the south of the study area but entirely by inner shelf deposits in the north. Late Pleistocene marine sediments are of inner shelf origin and Holocene deposits are marginal marine in nature. Pleistocene marine sediments are incised, particularly in the northern half of the embayment by lowstand paleovalleys, partly filled by fluvial/floodplain deposits and in some cases, overlain by remnants of transgressive estuarine sediments. The shallowing through time of Quaternary sediments reflects the eastward progradational geometry of the continental shelf. The preservation potential of marginal marine deposits (barrier island, shoreface, backbarrier deposits) is not high, except in topographic lows associated with late Pleistocene paleovalleys and inlets because the current interglacial highstand has not yet reached its highest level. Given the documented increase in rate of relative sea-level rise in this region, shallow marine conditions are likely to return to the central Albemarle Embayment in the near future.

North Carolina↗

Configuration of the Seattle Urban Seismic Array for the February 28, 2001, M6.8, Nisqually earthquake and its aftershocks

This is a description of the configuration of the Seattle Urban Seismic Array (click on thumbnail map to see full size map) at the time of the Nisqually earthquake and its aftershocks (from April 28 through March 3, 2001). The array is operated by the Geologic Hazards Team of the U. S Geological Survey. It has been recording small local earthquakes since its initial installation immediately after the Duvall earthquake in May 1996. Since then, we have been able to convert the array to all Kinemetrics K2s after retiring the aging DR-200s in June of 1998. The array stations have been moved around to suit our research interests. We had 26 instruments in urban Seattle at the time of the Nisqually earthquake. The primary research goal of the array is to record earthquake ground motion at sites scattered around the city that represent the major types of surficial geologic materials found in the city. With this information we plan to draw seismic hazard maps that will show the expected variability of ground shaking throughout the city. Our strategy to achieve our goal includes: 1) sampling ground motion at sites that represent the major geologic materials including man-made fill and alluvial surficial materials, 2) recording high-resolution ground motions from a tripartite array (SDN, SDS, and SDW) with about 200 meter spacing located on man-made fill in the SoDo (South of Downtown) industrial district, 3) recording ground motion in areas with man-made fill and alluvial surficial materials which have a high potential for liquifaction, 4) sampling ground motion at two sites on Capitol Hill (THO, and SEU) that are located near drill holes that have been logged for seismic velocity, 5) Providing long-term continuity at a few sites for comparison and reference, especially SEW and ALK, which are located on Tertiary bedrock. 6) recording ground motion at sites with similar surficial geology both inside and outside the Seattle Basin The configuration of the array is summarized in the accompanying table which is further described below.

Washington↗

Postglacial eruptive history and geochemistry of Semisopochnoi volcano, western Aleutian Islands, Alaska

Semisopochnoi Island, located in the Rat Islands group of the western Aleutian Islands and Aleutian volcanic arc, is a roughly circular island composed of scattered volcanic vents, the prominent caldera of Semisopochnoi volcano, and older, ancestral volcanic rocks. The oldest rocks on the island are gently radially dipping lavas that are the remnants of a shield volcano and of Ragged Top, which is an eroded stratocone southeast of the current caldera. None of these oldest rocks have been dated, but they all are likely Pleistocene in age. Anvil Peak, to the caldera’s north, has the morphology of a young stratocone and is latest Pleistocene to early Holocene in age. The oldest recognized Holocene deposits are those of the caldera-forming eruption, which produced the 7- by 6-km caldera in the center of the island, left nonwelded ignimbrite in valleys below the edifice, and left welded ignimbrite high on its flanks. The caldera-forming eruption produced rocks showing a range of intermediate whole-rock compositions throughout the eruption sequence, although a majority of clasts analyzed form a fairly tight cluster on SiO 2 -variation diagrams at 62.9 to 63.4 weight percent SiO 2 . This clustering of compositions at about 63 weight percent SiO 2 includes black, dense, obsidian-like clasts, as well as tan, variably oxidized, highly inflated pumice clasts. The best estimate for the timing of the eruption is from a soil dated at 6,920±60 14 C years before present underlying a thin facies of the ignimbrite deposit on the island’s north coast. Shortly after the caldera-forming eruption, two scoria cones on the northwest flank of the volcano outside the caldera, Ringworm crater and Threequarter Cone, simultaneously erupted small volumes of andesite. The oldest intracaldera lavas, on the floor of the caldera, are andesitic to dacitic, but are mostly covered by younger lavas and tephras. These intracaldera lavas include the basaltic andesites of small Windy cone, as well as the more voluminous basaltic andesites of three-peaked Mount Cerberus, which takes up most of the west half of the caldera and has erupted lavas that flowed to the sea on the southwestern coast of the island. Apparently active at the same time as Mount Cerberus, extracaldera Sugarloaf Peak at the southern point of the island has exclusively erupted basalts. Its young satellite peak, Sugarloaf Head, has erupted morphologically young lavas and cinder cones and may be the source of the last historical eruption in 1987. Several tephra sections on the east half of the island record as many as 50 tephras, mostly from Mount Cerberus, Sugarloaf Peak, and Sugarloaf Head, over the past several thousand years. Eruptive products of Semisopochnoi Island show an overall compositional range of basalt to dacite, though basaltic andesite and andesite constitute the largest proportions of rock types. They are tholeiitic, low to medium K, and have geochemical characteristics typical of magmatic arcs. The earliest Pleistocene lavas are mostly basalts that show the greatest geochemical diversity, as illustrated by, for example, La N /Yb N ratios of 1.9 to 3.5, suggesting fluctuations in the magma source region over the hundreds of thousands of years recorded by these older lavas. The Holocene rocks, in contrast, follow arrays in compositional space that suggest crystallization differentiation from discrete, subtly different batches of magma under varying pressure and temperature conditions. Increasingly negative Eu anomalies and an only modestly increasing alumina saturation index value with differentiation suggest that plagioclase and mafic silicates (amphibole and pyroxene) were involved to varying degrees in fractional crystallization to produce Semisopochnoi’s magmatic diversity. The crystal-poor, andesitic magmas that erupted during caldera formation likely separated from a plagioclase-, amphibole-, and clinopyroxene-dominated crystal residue in the upper crust at less than 900 °C, possibly following a period of decreased magmatic flux. During the Holocene, basaltic Sugarloaf Peak appears to bypass any upper crustal magmatic storage region and erupt crystal-rich basalts. Recent seismic swarms and long-lived warm springs attest to ongoing magmatic activity. The Holocene eruptive record at Semisopochnoi volcano is one of diverse eruptive styles as well as frequent eruptions from multiple vents located within and outside the caldera. The number and diversity of postcaldera vents means that the sites of future eruptions cannot be predicted with certainty. Future eruptions of ash similar in magnitude to the VEI 3 or less eruptions recorded in the documented tephra deposits would pose a hazard to aircraft in the region.

Alaska↗