USGS Science⌕ Search

SEARCH · USGS Science

Results for “Computers and Geology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56Linked to original sources
USGS2010

Historical changes in annual peak flows in Maine and implications for flood-frequency analyses

Flood-frequency analyses use statistical methods to compute peak streamflows for selected recurrence intervals— the average number of years between peak flows that are equal to or greater than a specified peak flow. Analyses are based on annual peak flows at a stream. It has long been assumed that the annual peak streamflows used in these computations were stationary (non-changing) over very long periods of time, except in river basins subject to direct effects of human activities, such as urbanization and regulation. Because of the potential effects of global warming on peak flows, the assumption of peak-flow stationarity has recently been questioned. Maine has many streamgages with 50 to 105 years of recorded annual peak streamflows. In this study, this long-term record has been tested for historical flood-frequency stationarity, to provide some insight into future flood frequency. Changes over time in annual instantaneous peak streamflows at 28 U.S. Geological Survey streamgages with long-term data (50 or more years) and relatively complete records were investigated by examining linear trends for each streamgage’s period of record. None of the 28 streamgages had more than 5 years of missing data. Eight streamgages have substantial streamflow regulation. Because previous studies have suggested that changes over time may have occurred as a step change around 1970, step changes between each streamgage’s older record (start year to 1970) and newer record (1971 to 2006) also were computed. The median change over time for all 28 streamgages is an increase of 15.9 percent based on a linear change and an increase of 12.4 percent based on a step change. The median change for the 20 unregulated streamgages is slightly higher than for all 28 streamgages; it is 18.4 percent based on a linear change and 15.0 percent based on a step change. Peak flows with 100- and 5-year recurrence intervals were computed for the 28 streamgages using the full annual peak-flow record and multiple sub-periods of that record using the guidelines (Bulletin 17B) of the Interagency Advisory Committee on Water Data. Magnitudes of 100- and 5-year peak flows computed from sub-periods then were compared to those computed from the full period. Sub-periods of 30 years with starting years staggered by 10 years were evaluated (1907–36, 1917–46, 1927–56, 1937–66, 1947–76, 1957–86, 1967–96, and 1977–2006). Two other sub-periods were evaluated using older data (start-of-record to 1970) and newer data (1971 to 2006). The 5-year peak flow is used to represent small and relatively frequent flood flows in Maine, whereas the 100-year peak flow is used to represent large flood flows. The 1967–96 sub-period generated the highest 100- and 5-year peak flows overall when compared to peak flows based on the full period of record; the median difference for all 28 streamgages is 8 percent for 100- and 5-year peak flows. The 1977–2006 and 1971–2006 sub-periods also generated 100- and 5-year peak flows higher than peak flows based on the full period of record, but not as high as the peak flows based on the 1967–96 sub-period. The 1937–66 sub-period generated the lowest 100- and 5-year peak flows overall. The median difference from full-period peak flows is -11 percent for 100-year peak flows and -8 percent for 5-year peak flows. Overall, differences between peak flows based on the sub-periods and those based on the full periods, generated using the 20 unregulated streamgages, are similar to differences using all 28 streamgages. Increases in the 5- and 100-year peak flows based on recent years of record are, in general, modest when compared to peak flows based on complete periods of record. The highest peak flows are based on the 1967–96 sub-period rather than the most recent sub-period (1977-2006). Peak flows for selected recurrence intervals are sensitive to very high peak flows that may occur once in a century or even less frequently. It is difficult, therefore, to determine which approach will produce the most reliable future estimates of peak flows for selected recurrence intervals, using only recent years of record or the traditional method using the entire historical period. One possible conservative approach to computing peak flows of selected recurrence intervals would be to compute peak flows using recent annual peak flows and the entire period of record, then choose the higher computed value. Whether recent or entire periods of record are used to compute peak flows of selected recurrence intervals, the results of this study highlight the importance of using recent data in the computation of the peak flows. The use of older records alone could result in underestimation of peak flows, particularly peak flows with short recurrence intervals, such as the 5-year peak flows.

Maine↗
USGS1989

IRIS/USGS plans for upgrading the Global Seismograph Network

This report has been prepared to provide information to organizations that may be asked to participate in a program to upgrade the global seismographic network. In most cases, the organizations that will be offered new instrumentation by the U.S. Geological Survey currently operate stations in the World-Wide Standardized Seismograph Network (WWSSN) or the Global Digital Seismograph Network (GDSN). The deployment of the WWSSN in the 1960's and the subsequent equipping of some WWSSN stations with digital equipment and borehole seismometers during the 1970's has been a remarkably successful program that generated the high- quality data needed to fuel an unprecedented period of progress in earthquake and tectonic research. The success of the WWSSN can be attributed to the importance of the data, to the strong commitment by participating organizations to international scientific cooperation, to the dedication and skill of the station operators, and to the resourcefulness of the staff supporting the network. Benefits have been widespread. The community of scientists world-wide has benefited from unrestricted access to a standardized base of calibrated data, and the participating stations have benefited from the donation of modern observatory instruments that have been useful for local earthquake studies and for the training of scientists and engineers. Now, an exciting opportunity has arisen to deploy a new generation of seismograph systems to replace the outdated equipment at many of the WWSSN and GDSN stations. The U.S. Geological Survey (USGS) is cooperating with the Incorporated Research Institutions for Seismology (IRIS) in a program to upgrade the global seismograph network. The equipment development phase is nearly complete with a prototype of the new broadband seismograph system currently undergoing final testing at the USGS Albuquerque Seismological Laboratory. Deployment of the new equipment is expected to begin in early 1990. As this report will demonstrate, the IRIS broadband seismograph system combines the very latest data acquisition and computer technology to produce seismic data with unprecedented bandwidth and dynamic range. Moreover, the system has been designed so that the high-quality digital data are accessible for local display and analysis. The functional design of the new system, which uses off-the-shelf modules and a standard computer bus, will make it much easier than it has been in the past to modify and upgrade the data acquisition system as improvements in technology become available. With adequate support for the program, the new IRIS seismograph system need never become obsolete. We want you to be aware of our plans and the possibility that you may be asked to participate in this ,program. The schedule for upgrading WWSSN and GDSN stations depends on the level of funding earmarked for the program by our National Science Foundation. We hope to deploy at least ten new GSN data systems each year. If you have any questions concerning this program, please contact the Albuquerque Seismological Laboratory, U.S. Geological Survey, Albuquerque, New Mexico 87115-5000. This report was revised in February 1992 in order to update information concerning the current program and instrumentation. The amp in Figure 1 was revised in June 1993, April 1994, December 1994, and September 1996 to reflect updated siting information. In September 1996 a composite photo of standard and optional components of the IRIS-2 GSN system hardware was added as a separate page between Figures 9 and 10.

Open-File Report↗
USGS1971

Reduction of lithologic-log data to numbers for use in the digital computer

The development of a standardized system for conveniently coding lithologic-log data for use in the digital computer has long been needed. The technique suggested involves a reduction of the original written alphanumeric log to a numeric log by use of computer programs. This numeric log can then be retrieved as a written log, interrogated for pertinent information, or analyzed statistically.

Journal of the International Association for Mathe↗
USGS2010

Vegetation classification and distribution mapping report: Canyon de Chelly National Monument

Executive Summary: The classification and distribution mapping of the vegetation of Canyon de Chelly National Monument (CACH) and surrounding environment was accomplished through a multi-agency effort between 2003 and 2007. The National Park Service’s Southern Colorado Plateau Network facilitated the team that conducted the work, which comprised the U.S. Geological Survey’s Southwest Biological Science Center and Fort Collins Science Center, Navajo Natural Heritage Program, Northern Arizona University, and NatureServe. The project team described 48 plant communities for CACH—35 of which were described from quantitative classification based on field-relevé data collected in 2004. Five additional plant communities were based on field relevés collected in a previous study. The team derived four additional plant communities from field observations during the photointerpretation phase of the project, and field documented them during accuracy assessment. The National Vegetation Classification Standard served as a conceptual framework for assigning these plant communities to the alliance and association level. Ten of the 48 plant communities were designated “park specials”, that is, plant communities with insufficient data to describe them as new alliances or associations. The project team also developed a spatial vegetation map database representing CACH, with three different map-class schemas: base, group, and management map classes. The base map classes represented the finest level of spatial detail. Photointerpreters delineated initial polygons through manual interpretation of 2003/2004 1:12,000-scale true color aerial photography supplemented by occasional computer screen digitizing on a mosaic of digitized aerial photos. These polygons were labeled with base map classes during photointerpretation. Field visits verified interpretation concepts. The vegetation map database includes • ? 53 base map classes, which consist of associations and park specials classified with the quantitative analysis • ? additional associations noted during photointerpretation • ? non-vegetated land cover, such as infrastructure, land use, and geological land cover. The base map classes consist of 4,718 polygons in the project area. A field-based accuracy assessment of the base map classes showed the overall accuracy to be 50.8% The group map classes represent aggregations of the base map classes, approximating the group level of the National Vegetation Classification Standard, Version 2 (Federal Geographic Data Committee 2008). Terrestrial ecological systems, as described by NatureServe (Comer et al. 2003), were used as a first approximation of the group level. The project team identified 16 group map classes in this project. The overall accuracy of the group map classes was determined using the same accuracy assessment data as for the base map classes. The overall accuracy of the group representation of vegetation was 79.9%. In consultation with park staff, the team developed management map classes that consisted of park-defined groupings of base map classes and were intended to represent a balance between maintaining required accuracy and providing a focus on vegetation of particular interest or import to park managers. The 28 management map classes have an overall accuracy of 77.1%. While the main products of this project are the vegetation classification and the vegetation map database, a number of ancillary geographic information system and digital database products were also produced that can be used independently, or to augment the main products. These products include shapefiles of the location of field-collected data and relational databases of field-collected data.

Report↗
USGS2007

Simulation of Water-Surface Elevations and Velocity Distributions at the U.S. Highway 13 Bridge over the Tar River at Greenville, North Carolina, Using One- and Two-Dimensional Steady-State Hydraulic Models

The use of one-dimensional hydraulic models currently is the standard method for estimating velocity fields through a bridge opening for scour computations and habitat assessment. Flood-flow contraction through bridge openings, however, is hydrodynamically two dimensional and often three dimensional. Although there is awareness of the utility of two-dimensional models to predict the complex hydraulic conditions at bridge structures, little guidance is available to indicate whether a one- or two-dimensional model will accurately estimate the hydraulic conditions at a bridge site. The U.S. Geological Survey, in cooperation with the North Carolina Department of Transportation, initiated a study in 2004 to compare one- and two-dimensional model results with field measurements at complex riverine and tidal bridges in North Carolina to evaluate the ability of each model to represent field conditions. The field data consisted of discharge and depth-averaged velocity profiles measured with an acoustic Doppler current profiler and surveyed water-surface profiles for two high-flow conditions. For the initial study site (U.S. Highway 13 over the Tar River at Greenville, North Carolina), the water-surface elevations and velocity distributions simulated by the one- and two-dimensional models showed appreciable disparity in the highly sinuous reach upstream from the U.S. Highway 13 bridge. Based on the available data from U.S. Geological Survey streamgaging stations and acoustic Doppler current profiler velocity data, the two-dimensional model more accurately simulated the water-surface elevations and the velocity distributions in the study reach, and contracted-flow magnitudes and direction through the bridge opening. To further compare the results of the one- and two-dimensional models, estimated hydraulic parameters (flow depths, velocities, attack angles, blocked flow width) for measured high-flow conditions were used to predict scour depths at the U.S. Highway 13 bridge by using established methods. Comparisons of pier-scour estimates from both models indicated that the scour estimates from the two-dimensional model were as much as twice the depth of the estimates from the one-dimensional model. These results can be attributed to higher approach velocities and the appreciable flow angles at the piers simulated by the two-dimensional model and verified in the field. Computed flood-frequency estimates of the 10-, 50-, 100-, and 500-year return-period floods on the Tar River at Greenville were also simulated with both the one- and two-dimensional models. The simulated water-surface profiles and velocity fields of the various return-period floods were used to compare the modeling approaches and provide information on what return-period discharges would result in road over-topping and(or) pressure flow. This information is essential in the design of new and replacement structures. The ability to accurately simulate water-surface elevations and velocity magnitudes and distributions at bridge crossings is essential in assuring that bridge plans balance public safety with the most cost-effective design. By compiling pertinent bridge-site characteristics and relating them to the results of several model-comparison studies, the framework for developing guidelines for selecting the most appropriate model for a given bridge site can be accomplished.

North Carolina↗
USGS1983

Characteristic analysis-1981: Final program and a possible discovery

The latest ornewest version of thecharacteristicanalysis (NCHARAN)computer program offers the exploration geologist a wide variety of options for integrating regionalized multivariate data. The options include the selection of regional cells for characterizing deposit models, the selection of variables that constitute the models, and the choice of logical combinations of variables that best represent these models. Moreover, the program provides for the display of results which, in turn, makes possible review, reselection, and refinement of a model. Most important, the performance of the above-mentioned steps in an interactive computing mode can result in a timely and meaningful interpretation of the data available to the exploration geologist. The most recent application of characteristic analysis has resulted in the possible discovery of economic sulfide mineralization in the Grong area in central Norway. Exploration data for 27 geophysical, geological, and geochemical variables were used to construct a mineralized and a lithogeochemical model for an area that contained a known massive sulfide deposit. The models were applied to exploration data collected from the Gjersvik area in the Grong mining district and resulted in the identification of two localities of possible mineralization. Detailed field examination revealed the presence of a sulfide vein system and a partially inverted stratigraphic sequence indicating the possible presence of a massive sulfide deposit at depth. ?? 1983 Plenum Publishing Corporation.

Journal of the International Association for Mathe↗
USGS1990

Surface displacements in the 1906 San Francisco and 1989 Loma Prieta earthquakes

The horizontal displacements accompanying the 1906 San Francisco earthquake and the 1989 Loma Prieta earthquake are computed from geodetic survey measurements. The 1906 earthquake displacement field is entirely consistent with right-lateral strike slip on the San Andreas fault. In contrast, the 1989 Loma Prieta earthquake exhibited subequal components of strike slip and reverse faulting. This result, together with other seismic and geologic data, may indicate that the two earthquakes occurred on two different fault planes.

California↗
USGS2012

Helping safeguard Veterans Affairs' hospital buildings by advanced earthquake monitoring

In collaboration with the U.S. Department of Veterans Affairs (VA), the National Strong Motion Project of the U.S. Geological Survey has recently installed sophisticated seismic systems that will monitor the structural integrity of hospital buildings during earthquake shaking. The new systems have been installed at more than 20 VA medical campuses across the country. These monitoring systems, which combine sensitive accelerometers and real-time computer calculations, are capable of determining the structural health of each structure rapidly after an event, helping to ensure the safety of patients and staff.

Fact Sheet↗
USGS2024

June 2022 floods in the Upper Yellowstone River Basin

Extraordinary floods surged down the Yellowstone River and its tributaries in northwestern Wyoming and south-central Montana on June 13–15, 2022. During the flood, U.S. Geological Survey staff worked to maintain real-time data from streamgages by making field measurements of streamflow and repairing damaged equipment while communicating the latest streamflow information with the public and with local, State, and Federal agencies. After the flood, staff surveyed high-water marks, computed peak streamflow at streamgages unreachable during the flood, and updated flood-frequency estimates for streamgages in the Upper Yellowstone River Basin. Streamflows were the highest on record at 17 streamgages in the Upper Yellowstone River Basin. River stages were highest on record at most of those streamgages. The flood-related data and analyses are summarized in this fact sheet.

Idaho, Montana, Wyoming↗
USGS1977

User's guide for U.S. Geological Survey rainfall-runoff models; revised 1977

Modified versions of the rainfall-runoff model described by Dawdy, Lichty, and Bergmann (1972) (see W72-11754) are used in the U.S. Geological Survey as a means of synthesizing flood discharges for small drainage areas. Synthesized flood discharges derived through use of long-term (60-70 year) rainfall and evaporation data, provide a more representative time base than do short-term (5-15 year) discharge records obtained by conventional stream gaging techniques. The rainfall, discharge, and evaporation data for use with rainfall-runoff models are stored in the Unit and Daily Values Files. Any of these data which were collected during the current or immediately preceding water year are stored on direct access, online disk files. Older data are stored in sequential files on magnetic tapes. Both the disks and tapes contain short-term data collected by the U.S. Geological Survey for calibration of models and long-term data for use in synthesis of long-term flood records. Information in this report provides guidelines for the assembly, storage, and retrieval of data needed to use these models, and also provides description and documentation of computer programs for model calibration and flood-record synthesis. (See also W74-11234) (Woodard-USGS)

Open-File Report↗
USGS1980

Water-level monitoring along San Andreas and San Jacinto faults, southern California, during fiscal year 1980

Beginning in October 1976, a program of water-level monitoring of abandoned water wells was initiated in the Palmdale area with the purpose of identifying possible water-level changes premonitory to a major earthquake on the San Andreas fault. In October 1977, the program was extended southeastward along the rift zone to the Valyermo area. In November 1977, the monitoring of water wells along the San Jacinto fault was initiated with the expectation of experiencing a moderate size earthquake while monitoring was in progress. Currently over thirty wells are being monitored. Eleven wells are monitored continuously with Stevens Type F recorders, two of which have been modified to operate with the Caltech Remote Observatory Support Systems (TIMS). The remaining wells are probed weekly, or in some cases semi-weekly or daily, by volunteers. We are endeavoring to improve the volunteer program by increasing the frequency of measurements and simplifying the procedure to minimize measurement errors. Weekly water-level data are displayed on computer-generated hydrographs for each well. Rainfall and earthquakes are plotted on the graphs for direct comparison with water levels. The hydrographs are updated and reviewed weekly. Weekly hydrographs are also prepared from recorder charts on two wells maintained by W. R. Moyle, Jr., of the U.S. Geological Survey, Water Resources Division Office, Laguna Niguel, California. A M5.5 earthquake occurred on 25 February 1980, between the Buck Ridge and San Jacinto strands of the San Jacinto fault zone, about 8 miles east-southeast of Anza. This is the largest earthquake which has occurred on the faults within our monitoring network. The Stevens recorder chart for well number 11S/6E-3N4 located in Borrego Valley about 20 miles southeast of the epicenter indicates that, during a period of about four hours on 21 February, the water level rose 1.5 to 1.6 feet and returned to its prior level. This is one of the most remarkable short-term water-level fluctuations observed during our monitoring program; it occurred about 88 hours prior to the earthquake. This well has been monitored since October 1977 and has had a Stevens recorder since October 1978. Long-term water levels have been remarkably steady compared to those in other wells we are monitoring. This well shows a strong response to earth tides. The Stevens record on a second well in Borrego Valley (11S/6E-1C1) showed a much smaller (0.1 foot) spike in water level at the same time as the spike in well number 11S/6E-3N4. Other continuously recording wells in Anza and Ocotillo Wells showed no identifiable water-level anomalies. The two wells in Borrego Valley which showed possible strain-induced water-level spikes appear to be more sensitive to earth tides than wells in the same area which did not show spikes in water level. We cannot conceive of any nontectonic cause for the spike on the Stevens record of well 11S/6E3N4. A creep event on the Coyote Creek fault about four miles from the well is one possibility. Because the spikes in the two wells in Borrego Valley are unique for the long-term record of these wells, they may represent precursors to the 25 February earthquake. Local seismic activity was also recorded in water levels of the two wells in Borrego Springs with continuous water-level recorders. One well showed peculiar high frequency water-level fluctuations from 22 July to 21 August 1980; since then the record has appeared normal. Several wells in the Palmdale-Valyermo area have shown peculiar changes in water level within the past year or so. The long-term hydrograph of well number 5N/12W-4H1 shows the most unusual behavior. The well showed no response to the 1977 and very heavy 1978 rainstorms, yet began to rise in early 1979 and continued to rise through the dry season of 1979. By comparison, most wells show a more normal seasonal response to rainfall. Eight wells in the Palmdale-Valyermo area have shown water-level changes which are different than would have been predicted from the previous history of water-level changes and seasonal rainfall. A longer period of observation is required to determine whether the changes are anomalous. Changes in the strain pattern and other geophysical phenomena have also been observed in southern California during about the same period as the water-level changes. If the water-level changes are the result of tectonic strain, the mechanism and significance are unknown. However, it is interesting that five of the eight wells with possibly anomalous water-level changes have been identified as good strain meters based on their response to earth tides. Six wells showing an unexpected rise in water level are located west of the earthquake swarm which occurred in 1976-1977 (McNally et al, 1978), whereas the two which show water levels lower than would have been predicted are located east of the earthquake swarm.

California↗
USGS1987

Interpretation of detailed aerial gamma-ray survey, Jabal Ashirah area, southeastern Arabian Shield, Kingdom of Saudi Arabia

A detailed aerial gamma-ray spectrometric survey of the Jabal Ashirah area in the southeastern Arabian Shield has been analyzed using computer-classification algorithms. The analysis resulted in maps that show radiometric map units and gamma-ray anomalies indicating the presence of possible concentrations of potassium and uranium. The radiometric-unit map was interpreted to 'produce a simplified radiolithic map that was correlated with the mapped geology. The gamma-ray data show uranium anomalies that coincide with a tin-bearing granite, but known gold and nickel mineralization do not have any associated gamma-ray signatures.

Open-File Report↗
USGS2013

An analysis of potential water availability from the Atwood, Leesville, and Tappan Lakes in the Muskingum River Watershed, Ohio

This report presents the results of a study to assess potential water availability from the Atwood, Leesville, and Tappan Lakes, located within the Muskingum River Watershed, Ohio. The assessment was based on the criterion that water withdrawals should not appreciably affect maintenance of recreation-season pool levels in current use. To facilitate and simplify the assessment, it was assumed that historical lake operations were successful in maintaining seasonal pool levels, and that any discharges from lakes constituted either water that was discharged to prevent exceeding seasonal pool levels or discharges intended to meet minimum in-stream flow targets downstream from the lakes. It further was assumed that the volume of water discharged in excess of the minimum in-stream flow target is available for use without negatively impacting seasonal pool levels or downstream water uses and that all or part of it is subject to withdrawal. Historical daily outflow data for the lakes were used to determine the quantity of water that potentially could be withdrawn and the resulting quantity of water that would flow downstream (referred to as “flow-by”) on a daily basis as a function of all combinations of three hypothetical target minimum flow-by amounts (1, 2, and 3 times current minimum in-stream flow targets) and three pumping capacities (1, 2, and 3 million gallons per day). Using both U.S. Geological Survey streamgage data and lake-outflow data provided by the U.S. Army Corps of Engineers resulted in analytical periods ranging from 51 calendar years for the Atwood Lake to 73 calendar years for the Leesville and Tappan Lakes. The observed outflow time series and the computed time series of daily flow-by amounts and potential withdrawals were analyzed to compute and report order statistics (95th, 75th, 50th, 25th, 10th, and 5th percentiles) and means for the analytical period, in aggregate, and broken down by calendar month. In addition, surplus-water mass curve data were tabulated for each of the lakes. Monthly order statistics of computed withdrawals indicated that, for the three pumping capacities considered, increasing the target minimum flow-by amount tended to reduce the amount of water that can be withdrawn. The reduction was greatest in the lower percentiles of withdrawal; however, increasing the flow-by amount had no impact on potential withdrawals during high flow. In addition, for a given target minimum flow-by amount, increasing the pumping rate increased the total amount of water that could be withdrawn; however, that increase was less than a direct multiple of the increase in pumping rate for most flow statistics. Potential monthly withdrawals were observed to be more variable and more limited in some calendar months than others. Monthly order statistics and means of computed daily mean flow-by amounts indicated that flow-by amounts generally tended to be lowest during June–October and February. Increasing the target minimum flow-by amount for a given pumping rate resulted in some small increases in the magnitudes of the mean and 50th percentile and lower order statistics of computed mean flow-by, but had no effect on the magnitudes of the higher percentile statistics. Increasing the pumping rate for a given target minimum flow-by amount resulted in decreases in magnitudes of higher-percentile flow-by statistics by an amount equal to the flow equivalent of the increase in pumping rate; however, some lower percentile statistics remained unchanged.

Ohio↗
USGS2015

Flood-inundation maps for the Hoosic River, North Adams and Williamstown, Massachusetts, from the confluence with the North Branch Hoosic River to the Vermont State line

A series of nine digital flood-inundation maps were developed for an 8-mile reach of the Hoosic River in North Adams and Williamstown, Massachusetts, by the U.S. Geological Survey (USGS) in cooperation with the Federal Emergency Management Agency. The coverage of the maps extends from the confluence with the North Branch Hoosic River to the Vermont State line. Peak flows with 20-, 10-, 4-, 2-, 1-, 0.5-, and 0.2-percent annual exceedance probabilities were computed for the reach from updated flood-frequency analyses. These peak flows were routed through a one-dimensional step-backwater hydraulic model to obtain the corresponding peak water-surface elevations, and to place the tropical storm Irene flood of August 28, 2011 into historical context. The hydraulic model was calibrated by using the current (2014) stage-discharge relation at the USGS streamgage Hoosic River near Williamstown, Massachusetts (01332500), and from documented high-water marks from the tropical storm Irene flood, which had approximately a 1-percent annual exceedance probability. The hydraulic model was used to compute water-surface profiles for flood stages referenced to the streamgage and ranging from 9 feet (ft; 624.45 ft North American Vertical Datum of 1988 [NAVD 1988]), which is near bankfull, to 16.1 ft (631.59 ft NAVD 1988), which exceeds the maximum recorded water level at the streamgage and the National Weather Service major flood stage of 13.0 ft. The mapped stages, 10.9 to 16.1 ft, were selected to match the stages of flows with annual exceedance probabilities between 20 and 0.2 percent, and thus do not fall at exact 1-ft increments. The simulated water-surface profiles were combined with a geographic information system digital elevation model derived from light detection and ranging (lidar) data having a 0.5-ft vertical accuracy to create a set of flood-inundation maps. The availability of the flood-inundation maps, combined with information regarding current (near real-time) stage from USGS streamgage Hoosic River near Williamstown, and forecasted flood stages from the National Weather Service Advanced Hydrologic Prediction Service will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, and post-flood recovery efforts. The flood-inundation maps are nonregulatory, but provide Federal, State, and local agencies and the public with estimates of the potential extent of flooding during selected peak-flow events.

Massachusetts↗
USGS1978

EROS Data Center Landsat digital enhancement techniques and imagery availability

The US Geological Survey's EROS Data Center (EDC) is experimenting with the production of digitally enhanced Landsat imagery. Advanced digital image processing techniques are used to perform geometric and radiometric corrections and to perform contrast and edge enhancements. The enhanced image product is produced from digitally preprocessed Landsat computer compatible tapes (CCTs) on a laser beam film recording system. Landsat CCT data have several geometric distortions which are corrected when NASA produces the standard film products. When producing film images from CCT's, geometric correction of the data is required. The EDC Digital Image Enhancement System (EDIES) compensates for geometric distortions introduced by Earth's rotation, variable line length, non-uniform mirror scan velocity, and detector misregistration. Radiometric anomalies such as bad data lines and striping are common to many Landsat film products and are also in the CCT data. Bad data lines or line segments with more than 150 contiguous bad pixels are corrected by inserting data from the previous line in place of the bad data. Striping, caused by variations in detector gain and offset, is removed with a destriping algorithm applied after digitally enhancing the data. Image enhancement is performed by applying a linear contrast stretch and an edge enhancement algorithm. The linear contrast enhancement algorithm is designed to expand digitally the full range of useful data recorded on the CCT over the range of 256 digital counts. This minimizes the effect of atmospheric scattering and saturates the relative brightness of highly reflecting features such as clouds or snow. It is the intent that no meaningful terrain data are eliminated by the digital processing. The edge enhancement algorithm is designed to enhance boundaries between terrain features that exhibit subtle differences in brightness values along edges of features. After the digital data have been processed, data for each Landsat band are recorded on black-and-white film with a laser beam film recorder (LBR). The LBR corrects for aspect ratio distortions as the digital data are recorded on the recording film over a preselected density range. Positive transparencies of MSS bands 4, 5, and 7 produced by the LBR are used to make color composite transparencies. Color film positives are made photographically from first generation black-and-white products generated on the LBR.

Canadian Journal of Remote Sensing↗
USGS2015

Synoptic evaluation of scale-dependent metrics for hydrographic line feature geometry

Methods of acquisition and feature simplification for vector feature data impact cartographic representations and scientific investigations of these data, and are therefore important considerations for geographic information science (Haunert and Sester 2008). After initial collection, linear features may be simplified to reduce excessive detail or to furnish a reduced-scale version of the features through cartographic generalization (Regnauld and McMaster 2008, Stanislawski et al. 2014). A variety of algorithms exist to simplify linear cartographic features, and all of the methods affect the positional accuracy of the features (Shahriari and Tao 2002, Regnauld and McMaster 2008, Stanislawski et al. 2012). In general, simplification operations are controlled by one or more tolerance parameters that limit the amount of positional change the operation can make to features. Using a single tolerance value can have varying levels of positional change on features; depending on local shape, texture, or geometric characteristics of the original features (McMaster and Shea 1992, Shahriari and Tao 2002, Buttenfield et al. 2010). Consequently, numerous researchers have advocated calibration of simplification parameters to control quantifiable properties of resulting changes to the features (Li and Openshaw 1990, Raposo 2013, Tobler 1988, Veregin 2000, and Buttenfield, 1986, 1989). This research identifies relations between local topographic conditions and geometric characteristics of linear features that are available in the National Hydrography Dataset (NHD). The NHD is a comprehensive vector dataset of surface 18 th ICA Workshop on Generalisation and Multiple Representation, Rio de Janiero, Brazil 2015 2 water features within the United States that is maintained by the U.S. Geological Survey (USGS). In this paper, geometric characteristics of cartographic representations for natural stream and river features are summarized for subbasin watersheds within entire regions of the conterminous United States and compared to topographic metrics. A concurrent processing workflow is implemented using a Linux high-performance computing cluster to simultaneously process multiple subbasins, and thereby complete the work in a fraction of the time required for a single-process environment. In addition, similar metrics are generated for several levels of simplification of the hydrographic features to quantify the effects of simplification over the various landscape conditions. Objectives of this exploratory investigation are to quantify geometric characteristics of linear hydrographic features over the various terrain conditions within the conterminous United States and thereby illuminate relations between stream geomorphological conditions and cartographic representation. The synoptic view of these characteristics over regional watersheds that is afforded through concurrent processing, in conjunction with terrain conditions, may reveal patterns for classifying cartographic stream features into stream geomorphological classes. Furthermore, the synoptic measurement of the amount of change in geometric characteristics caused by the several levels of simplification can enable estimation of tolerance values that appropriately control simplification-induced geometric change of the cartographic features within the various geomorphological classes in the country. Hence, these empirically derived rules or relations could help generate multiscale-representations of features through automated generalization that adequately maintain surface drainage variations and patterns reflective of the natural stream geomorphological conditions across the country.

Conference Paper↗
USGS2023

Linear regression model documentation for computing water-quality constituent concentrations or densities using continuous real-time water-quality data for the Kansas River above Topeka Weir at Topeka, Kansas, November 2018 through June 2021

The Kansas River and its associated alluvial aquifer provide drinking water to more than 950,000 people in northeastern Kansas. Water suppliers that rely on the Kansas River as a water-supply source use physical and chemical processes to treat and remove contaminants before public distribution. An early-notification system of changing water-quality conditions allows water suppliers to proactively make decisions that affect water treatment. The U.S. Geological Survey (USGS), in cooperation with the Kansas Water Office (funded in part through the Kansas Water Plan), the Kansas Department of Health and Environment, The Nature Conservancy, the City of Lawrence, the City of Manhattan, the City of Olathe, the City of Topeka, WaterOne, and Evergy, began collecting water-quality data at the Kansas River above Topeka Weir at Topeka, Kansas (USGS site 06888990, hereafter referred to as the “Topeka site”), during November 2018 to develop linear regression models that relate continuous in situ water-quality sensor measurements to discretely sampled water-quality constituent concentrations or densities. The addition of the Topeka site expanded an existing water-quality monitoring network, which included the upstream Kansas River at Wamego, Kans., and downstream Kansas River at De Soto, Kans., sites. Linear regression analysis was used to develop models that compute real-time concentrations or densities for total dissolved solids, major ions, hardness as calcium carbonate, nutrients (nitrogen and phosphorus species), chlorophyll a , total suspended solids, suspended sediment, and Escherichia coli at the Topeka site using data collected during November 2018 through June 2021. Water-quality constituent concentrations or densities computed from the models documented in this report are available at the USGS National Real-Time Water-Quality website (https://nrtwq.usgs.gov), are useful to the public for cultural and recreational purposes, and can be used to guide water-treatment processes, compare conditions with Federal and State water-quality criteria, and characterize changes in Kansas River water-quality conditions through time.

Kansas↗
USGS2026

Multiple-well monitoring site adjacent to the Midway- Sunset and Buena Vista Oil Fields, Kern County, California

Groundwater quality in and around oil fields in the Southern San Joaquin Valley is of interest to many California residents that rely heavily on groundwater for domestic, commercial, and agricultural use. To help assess the effects of historical oil-field activities and natural geologic sources on groundwater near the southwest margins of the Kern County Groundwater Subbasin, a multiple-well monitoring site was installed near the administrative boundary between the Midway-Sunset and Buena Vista Oil Fields in Kern County, California. The installation of the Midway-Sunset Buena Vista multiple-well monitoring site (MSBV) supports regional analysis of the relations of oil and gas sources to groundwater quality by providing information about the geology, hydrology, geophysical properties, and water quality of the alluvial and upper Tulare aquifers in areas where groundwater data were limited. Data collected from the site included drill cuttings, whole core samples, sidewall core samples, mud-gas analysis, borehole geophysical logs, depth to water measurements, and water quality samples. Whole cores were scanned using dual energy computed tomography. Subsamples of selected cores were analyzed for density, porosity, specific retention, and bulk minerology. Thin sections of the subsamples were prepared, photographed, and examined. Two samples were analyzed using scanning electron microscope technology to examine the microporosity of diatomite laden sediment. Instrumentation installed in the wells collect hourly depth to water measurements. Analysis of the data show there is 355 feet of alluvium overlying the Tulare Formation at the well site. The contact between the two formations is an aquitard resulting in a perched aquifer in the alluvium and unconfined aquifer in the Tulare Formation. The alluvium is more heterogenous and finer grained than the Tulare Formation resulting in markedly higher porosity in the alluvium compared to the Tulare Formation. Higher specific retention observed in the alluvium is attributed to the finer grained sediment and greater abundance of reworked diatomite (as represented by opal-CT [cristobalite-tridymite]) compared to the Tulare Formation. Total dissolved solids (TDS) approached or exceeded 10,000 milligrams per liter (mg/L) in the alluvium from approximately 176 to 242 feet below land surface and at the top of the Amnicola clay at approximately 670 feet below land surface within the Tulare Formation. Elevated TDS, chloride, and boron concentrations in the alluvium and on top of the Amnicola clay likely reflect groundwater that is mixed with oil-field water. Water chemistry and modern-aged groundwater in the alluvial monitoring well (MSBV #3) are consistent with the oil-field water in the alluvium being derived from documented historical surface disposal of oil-field water upslope (northwest) of the site. Water chemistry and pre-modern groundwater age in the deeper Tulare monitoring well (MSBV #1) on top of the Amnicola clay are consistent with oil-field fluids derived from upslope natural geologic sources or old oil wells that leak in the subsurface. Shallow groundwater in the Tulare (MSBV #2) is not affected by mixing with oil-field sources.

EarthArXiv↗