SEARCH · USGS Science

Results for “Chemical Geology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56Linked to original sources

USGS1984

Water resources of the Yap Islands

The Yap Islands consist of four major islands, Yap, Gagil-Tamil, Maap, and Rumung. Of these, Yap Island has more than half the total land area, most of the population, and almost all of the economic development. The islands of Maap and Rumung together compose only 15 percent of the land area and population. Average annual rainfall over the Yap Islands amounts to 122 inches. Rainfall-runoff comparisons indicate that about half of the annual rainfall runs off to the ocean on Yap Island and Gagil-Tamil. Streams on Gagil-Tamil are perennial but streams on Yap Island are dry an average of 3 months per year due to geologic differences. Analyses of water samples from 23 sources show the good quality and the chemical similarity of surface and ground water. This report summarizes the hydrologic data collected and provides interpretations that can be used by the planning and public works officials of Yap to make decisions concerning development and management of their water resources.

Open-File Report↗

USGS1993

Methods for sampling fish communities as part of the National Water-Quality Assessment Program

Fish community structure is characterized in the U.S. Geological Survey's National Water-Quality Assessment Program as part of an integrated physical, chemical, and biological assessment of the Nation's water quality. The objective of the National Water-Quality Assessment characterization of fish community structure is to relate fish community characteristics to physical, chemical, and other biological factors to assess water-quality conditions. To accomplish this, fish community structure is described at sites representing selected environmental settings. In addition, spatial and temporal patterns in fish community structure are examined at local, regional, and national levels. A representative sample of the fish community is collected by sampling a stream reach using two complementary methods. The primary collection method is electrofishing using backpack, towed, or boat-operated electrofishing gear; seining is a secondary technique. Other secondary techniques may be substituted after careful consideration of sampling efficiency and consultation with local fish ecologists. Before fish sampling is conducted, careful consideration must be given to collecting permits; protecting endangered, threatened, and special-concern species; and coordinating sampling efforts with other fish ecologists. After the sample is collected, individual fish are identified to species by ichthyologists. Length and weight measurements are taken, and the presence of external anomalies are recorded.

Open-File Report↗

USGS1993

Methods for characterizing stream habitat as part of the National Water-Quality Assessment Program

Stream habitat is characterized in the U.S. Geological Survey's National Water-Quality Assessment Program as part of an integrated physical, chemical, and biological assessment of the Nation's water quality. The goal of stream habitat characterization is to relate habitat to other physical, chemical, and biological factors to describe water-quality conditions. To accomplish this goal, environmental settings are described at sites selected for water-quality assessment. In addition, spatial and temporal patterns in habitat are examined at local, regional, and national levels. Although habitat characterization is an important component of a number of Federal, State, and local water-quality assessment programs, no current set of habitat evaluation procedures meets the objectives of the habitat assessment component of the National Water-Quality Assessment Program. Evaluation of stream habitat is based on a spatially hierarchical framework that incorporates habitat data at basin, segment, reach, and microhabitat scales. This framework provides a basis for national consistency in collection techniques while allowing flexibility in habitat assessment within individual study units. Procedures are described for collecting habitat data at basin and stream segment scales that include use of geographic information system data bases, maps, and aerial photographs. Data collected at the stream reach scale include more than 34 riparian and instream habitat characteristics evaluated during onetime site visits, and surveys of the channel and riparian area during repeated sampling.

Open-File Report↗

USGS1993

Methods for collecting algal samples as part of the National Water-Quality Assessment Program

Benthic algae (periphyton) and phytoplankton communities are characterized in the U.S. Geological Survey's National Water-Quality Assessment Program as part of an integrated physical, chemical, and biological assessment of the Nation's water quality. This multidisciplinary approach provides multiple lines of evidence for evaluating water-quality status and trends, and for refining an understanding of the factors that affect water-quality conditions locally, regionally, and nationally. Water quality can be characterized by evaluating the results of qualitative and quantitative measurements of the algal community. Qualitative periphyton samples are collected to develop of list of taxa present in the sampling reach. Quantitative periphyton samples are collected to measure algal community structure within selected habitats. These samples of benthic algal communities are collected from natural substrates, using the sampling methods that are most appropriate for the habitat conditions. Phytoplankton samples may be collected in large nonwadeable streams and rivers to meet specific program objectives. Estimates of algal biomass (chlorophyll content and ash-free dry mass) also are optional measures that may be useful for interpreting water-quality conditions. A nationally consistent approach provides guidance on site, reach, and habitat selection, as well as information on methods and equipment for qualitative and quantitative sampling. Appropriate quality-assurance and quality-control guidelines are used to maximize the ability to analyze data locally, regionally, and nationally.

Open-File Report↗

USGS1994

Biology as an integrated component of the U.S. Geological Survey's National Water-Quality Assessment Program

The U.S. Geological Survey?s (USGS) National Water-Quality Assessment (NAWQA) Program is designed to integrate chemical, physical, and biological data to assess the status of and trends in the Nation?s water quality at local, regional, and national levels. The Program consists of 60 study units (major river basins and large parts of aquifers) located throughout the Nation (fig. 1). Data are collected at stream, river, and ground-water sites that represent the Nation?s mix of major natural and human factors that influence water quality. Biological data are collected from streams and rivers, and include (1) fish and other aquatic organisms whose tissues are analyzed for a wide array of chemical contaminants; (2) characterizations of algal, benthic invertebrate, and fish communities; and (3) characterizations of vegetation growing in streams and along streambanks. These biological data are collected in conjunction with physical (streamflow, characterizations of instream, bank, and flood-plain habitats) and chemical data.

Open-File Report↗

USGS1996

Reconnaissance of volatile organic compounds in the subsurface at Rutgers University, Busch Campus, Piscataway Township, New Jersey

During 1991-92, the U.S. Geological Survey conducted a hydrogeologic reconnaissance at a site near the Rutgers University, Busch Campus, Chemical Engineering building, C-Wing. Results of analyses of the soil-gas samples, which were collected at 43 locations, indicated the presence of volatile organic compounds, primarily carbon tetrachloride, near the C-Wing building and about 550 feet downgradient from and southwest of the C-Wing building. Concentrations of the compound in soil-gas samples were highest (2.1 ug/L (micrograms per liter)) along the southwestern wall of the C-Wing building. Ground-water samples were collected at depths as great as 55 feet from five wells and piezometers near the C-Wing building. Samples collected along the southwestern wall of the building also contained the highest concentrations of volatile organic compounds. Concentrations of carbon tetrachloride in the ground-water samples ranged from < 0.35 ug/L to 3,400 ug/L, and concentrations of tetrachloro- ethylene ranged from < 0.28 ug/L to 85 ug/L. Ground-water samples collected at depths of 55 feet or more from two wells located on the Rutgers University Golf Course about 2,400 feet down- gradient from the C-Wing building contained concentrations of tetrachloroethylene as great as 17.7 ug/L. Water levels measured in six wells and six piezometers indicated that the general flow direction in the shallow part of the aquifer is to the southwest of the C-Wing building. An electrical-resistivity survey was conducted by azimuthal resistivity techniques. The results of the survey were consistent with field measurements, and the dominant vertical fractures near the Busch Campus trend northeast. An electromagnetic survey was ineffective as a result of cultural interferences and could not be used to determine the hydrogeologic characteristics of the site.

New Jersey↗

USGS2014

Concentrations, loads, and yields of total phosphorus, total nitrogen, and suspended sediment and bacteria concentrations in the Wister Lake Basin, Oklahoma and Arkansas, 2011-13

The Poteau Valley Improvement Authority uses Wister Lake in southeastern Oklahoma as a public water supply. Total phosphorus, total nitrogen, and suspended sediments from agricultural runoff and discharges from wastewater treatment plants and other sources have degraded water quality in the lake. As lake-water quality has degraded, water-treatment cost, chemical usage, and sludge production have increased for the Poteau Valley Improvement Authority. The U.S. Geological Survey (USGS), in cooperation with the Poteau Valley Improvement Authority, investigated and summarized concentrations of total phosphorus, total nitrogen, suspended sediment, and bacteria (Escherichia coli and Enterococcus sp.) in surface water flowing to Wister Lake. Estimates of total phosphorus, total nitrogen, and suspended sediment loads, yields, and flow-weighted mean concentrations of total phosphorus and total nitrogen concentrations were made for the Wister Lake Basin for a 3-year period from October 2010 through September 2013. Data from water samples collected at fixed time increments during base-flow conditions and during runoff conditions at the Poteau River at Loving, Okla. (USGS station 07247015), the Poteau River near Heavener, Okla. (USGS station 07247350), and the Fourche Maline near Leflore, Okla. (USGS station 07247650), water-quality stations were used to evaluate water quality over the range of streamflows in the basin. These data also were collected to estimate annual constituent loads and yields by using regression models. At the Poteau River stations, total phosphorus, total nitrogen, and suspended sediment concentrations in surface-water samples were significantly larger in samples collected during runoff conditions than in samples collected during base-flow conditions. At the Fourche Maline station, in contrast, concentrations of these constituents in water samples collected during runoff conditions were not significantly larger than concentrations during base-flow conditions. Flow-weighted mean total phosphorus concentrations at all three stations from 2011 to 2013 were several times larger than the Oklahoma State Standard for Scenic Rivers (0.037 milligrams per liter [mg/L]), with the largest flow-weighted phosphorus concentrations typically being measured at the Poteau River at Loving, Okla., station. Flow-weighted mean total nitrogen concentrations did not vary substantially between the Poteau River stations and the Fourche Maline near Leflore, Okla., station. At all of the sampled water-quality stations, bacteria (Escherichia coli and Enterococcus sp.) concentrations were substantially larger in water samples collected during runoff conditions than in water samples collected during base-flow conditions from 2011 to 2013. Estimated annual loads of total phosphorus, total nitrogen, and suspended sediment in the Poteau River stations during runoff conditions ranged from 82 to 98 percent of the total annual loads of those constituents. Estimated annual loads of total phosphorus, total nitrogen, and suspended sediment in the Fourche Maline during runoff conditions ranged from 86 to nearly 100 percent of the total annual loads. Estimated seasonal total phosphorus loads generally were smallest during base-flow and runoff conditions in autumn. Estimated seasonal total phosphorus loads during base-flow conditions tended to be largest in winter and during runoff conditions tended to be largest in the spring. Estimated seasonal total nitrogen loads tended to be smallest in autumn during base-flow and runoff conditions and largest in winter during runoff conditions. Estimated seasonal suspended sediment loads tended to be smallest during base-flow conditions in the summer and smallest during runoff conditions in the autumn. The largest estimated seasonal suspended sediment loads during runoff conditions typically were in the spring. The estimated mean annual total phosphorus yield was largest at the Poteau River at Loving, Okla., water-quality station. The estimated mean annual total phosphorus yield was largest during base flow at the Poteau River at Loving, Okla., water-quality station and at both of the Poteau River water-quality stations during runoff conditions. The estimated mean annual total nitrogen yields were largest at the Poteau River water-quality stations. Estimated mean annual total nitrogen yields were largest during base-flow and runoff conditions at the Poteau River at Loving, Okla., water-quality station. The estimated mean annual suspended sediment yield was largest at the Poteau River near Heavener, Okla., water-quality station during base-flow and runoff conditions. Flow-weighted mean concentrations indicated that total phosphorus inputs from the Poteau River Basin in the Wister Lake Basin were larger than from the Fourche Maline Basin. Flow-weighted mean concentrations of total nitrogen did not vary spatially in a consistent manner. The Poteau River and the Fourche Maline contributed estimated annual total phosphorus loads of 137 to 278 tons per year (tons/yr) to Wister Lake. Between 89 and 95 percent of the annual total phosphorus loads were transported to Wister Lake during runoff conditions. The Poteau River and the Fourche Maline contributed estimated annual total nitrogen loads of 657 to 1,294 tons/yr, with 86 to 94 percent of the annual total nitrogen loads being transported to Wister Lake during runoff conditions. The Poteau River and the Fourche Maline contributed estimated annual total suspended sediment loads of 110,919 to 234,637 tons/yr, with 94 to 99 percent of the annual suspended sediment loads being transported to Wister Lake during runoff conditions. Most of the total phosphorus and suspended sediment were delivered to Wister Lake during runoff conditions in the spring. The majority of the total nitrogen was delivered to Wister Lake during runoff conditions in winter.

Arkansas;Oklahoma↗

USGS2021

Optimization of the Idaho National Laboratory water-quality aquifer monitoring network, southeastern Idaho

Long-term monitoring of water-quality data collected from wells at the Idaho National Laboratory (INL) has provided essential information for delineating the movement of radiochemical and chemical wastes in the eastern Snake River Plain aquifer, southeastern Idaho. Since 1949, the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, has maintained as many as 200 wells in the INL water-quality monitoring network. A network design tool, distributed as an R package, was developed to evaluate and optimize groundwater monitoring in the existing network based on water-quality data collected at 153 sampling sites since January 1, 1989. The objective of the optimization design tool is to reduce well monitoring redundancy while retaining sufficient data to reliably characterize water-quality conditions in the aquifer. A spatial optimization was used to identify a set of wells whose removal leads to the smallest increase in the deviation between interpolated concentration maps using the existing and reduced monitoring networks while preserving significant long-term trends and seasonal components in the data. Additionally, a temporal optimization was used to identify reductions in sampling frequencies by minimizing the redundancy in sampling events. Spatial optimization uses an islands genetic algorithm to identify near-optimal network designs removing 10, 20, 30, 40, and 50 wells from the existing monitoring network. With this method, choosing a greater number of wells to remove results in greater cost savings and decreased accuracy of the average relative difference between interpolated maps of the reduced-dataset and the full-dataset. The genetic search algorithm identified reduced networks that best capture the spatial patterns of the average concentration plume while preserving long-term temporal trends at individual wells. Concentration data for 10 analyte types are integrated in a single optimization so that all datasets may be evaluated simultaneously. A constituent was selected for inclusion in the spatial optimization problem when the observations were sufficient to (1) establish a two-range variability model, (2) classify at least one concentration time series as a continuous record block, and (3) make a prediction using the quantile-kriging interpolation method. The selected constituents include sodium, chloride, sulfate, nitrate, carbon tetrachloride, 1,1-dichloroethylene, 1,1,1-trichloroethane, trichloroethylene, tritium, strontium-90, and plutonium-238. In temporal optimization, an iterative-thinning method was used to find an optimal sampling frequency for each analyte-well pair. Optimal frequencies indicate that for many of the wells, samples may be collected less frequently and still be able to characterize the concentration over time. The optimization results indicated that the sample-collection interval may be increased by an of average of 273 days owing to temporal redundancy.

Idaho↗

USGS2002

Streamflow gains and losses along San Francisquito Creek and characterization of surface-water and ground-water quality, southern San Mateo and northern Santa Clara counties, California, 1996-97

San Francisquito Creek is an important source of recharge to the 22-square-mile San Francisquito Creek alluvial fan ground-water subbasin in the southern San Mateo and northern Santa Clara Counties of California. Ground water supplies as much as 20 percent of the water to some area communities. Local residents are concerned that infiltration and consequently ground-water recharge would be reduced if additional flood-control measures are implemented along San Francisquito Creek. To improve the understanding of the surface-water/ground-water interaction between San Francisquito Creek and the San Francisquito Creek alluvial fan, the U.S. Geological Survey (USGS) estimated streamflow gains and losses along San Francisquito Creek and determined the chemical quality and isotopic composition of surface and ground water in the study area.Streamflow was measured at 13 temporary streamflow-measurement stations to determine streamflow gains and losses along a 8.4-mile section of San Francisquito Creek. A series of five seepage runs between April 1996 and May 1997 indicate that losses in San Francisquito Creek were negligible until it crossed the Pulgas Fault at Sand Hill Road. Streamflow losses increased between Sand Hill Road and Middlefield Road where the alluvial deposits are predominantly coarse-grained and the water table is below the bottom of the channel. The greatest streamflow losses were measured along a 1.8-mile section of the creek between the San Mateo Drive bike bridge and Middlefield Road; average losses between San Mateo Drive and Alma Street and from there to Middlefield Road were 3.1 and 2.5 acre-feet per day, respectively.Downstream from Middlefield Road, streamflow gains and losses owing to seepage may be masked by urban runoff, changes in bank storage, and tidal effects from San Francisco Bay. Streamflow gains measured between Middlefield Road and the 1200 block of Woodland Avenue may be attributable to urban runoff and (or) ground-water inflow. Water-level measurements from nearby wells indicate that the regional water table may coincide with the channel bottom along this reach of San Francisquito Creek, particularly during the winter and early spring when water levels usually reach their maximum. Streamflow losses resumed below the 1200 block of Woodland Avenue, extending downstream to Newell Road. Discharge from a large storm drain between Newell Road and East Bayshore Road may account for the streamflow gains measured between these sites. Streamflow gains were measured between East Bayshore Road and the Palo Alto Municipal Golf Course, but this reach is difficult to characterize because of the probable influence of high tides.Estimated average streamflow losses totaled approximately 1,050 acre-feet per year for the reaches between USGS stream gage 11164500 at Stanford University (upstream of Junipero Serra Boulevard) and the Palo Alto Municipal Golf Course, including approximately 595 acre-feet per year for the 1.8-mile section between San Mateo Drive and Middlefield Road. Approximately 58 percent, or 550 acre-feet, of the total estimated average annual recharge from San Francisquito Creek occurs between the San Mateo Drive and Middlefield Road sites.The chemical composition of San Francisquito Creek water varies as a function of seasonal changes in hydrologic conditions. Measurements of specific conductance indicate that during dry weather and low flow, the dissolved-solids concentrations tends to be high, and during wet weather, the concentration tends to be low owing to dilution by surface water. Compared with water samples from upstream sites at USGS stream gage 11164500 and San Mateo Drive, the samples from the downstream sites at Alma Street and Woodland Avenue had low specific conductance; low concentrations of magnesium, sodium, sulfate, chloride, boron, and total dissolved solids; high nutrient concentrations; and light isotopic compositions indicating that urban runoff constitutes most of the streamflow

Water-Resources Investigations Report↗

USGS1995

Ground-water flow and the possible effects of remedial actions at J-Field, Aberdeen Proving Ground, Maryland

J-Field, located in the Edgewood Area of Aberdeen Proving Ground, Md, has been used since World War II to test and dispose of explosives, chemical warfare agents, and industrial chemicals resulting in ground-water, surface-water, and soil contami- nation. The U.S. Geological Survey finite-difference model was used to better understand ground-water flow at the site and to simulate the effects of remedial actions. A surficial aquifer and a confined aquifer were simulated with the model. A confining unit separates these units and is represented by leakance between the layers. The area modeled is 3.65 mi2; the model was constructed with a variably spaced 40 X 38 grid. The horizontal and lower boundaries of the model are all no-flow boundaries. Steady-state conditions were used. Ground water at the areas under investigation flows from disposal pit areas toward discharge areas in adjacent estuaries or wetlands. Simulations indicate that capping disposal areas with an impermeable cover effectively slows advective ground water flow by 0.7 to 0.5 times. Barriers to lateral ground-water flow were simulated and effectively prevented the movement of ground water toward discharge areas. Extraction wells were simulated as a way to contain ground-water contamination and to extract ground water for treatment. Two wells pumping 5 gallons per minute each at the toxic-materials disposal area and a single well pumping 2.5 gallons per minute at the riot-control-agent disposal area effectively contained contamination at these sites. A combi- nation of barriers to horizontal flow east and south of the toxic-materials disposal area, and a single extraction well pumping at 5 gallons per minute can extract contaminated ground water and prevent pumpage of marsh water.

Water-Resources Investigations Report↗

USGS1960

Geology and ground-water resources of the Rawlins area, Carbon County, Wyoming

The Rawlins area in west-central Carbon County, south-central Wyoming includes approximately 634 square miles of plains and valleys grading into relatively rugged uplifts. The climate is characterized by low precipitation, rapid evaporation, and a wide range of temperature. Railroading and ranching are the principal occupations in the area. The exposed rocks in the area range in age from Precambrian through Recent. The older formations are exposed in the uplifted parts, the oldest being exposed along the apex of the Rawlins uplift. The formations dip sharply away from the anticlines and other uplifts and occur in the subsurface throughout the remainder of the area. The Cambrian rocks (undifferentiated), Madison limestone, Tensleep sandstone, Sun dance formation, Cloverly formation, Frontier formation, and Miocene and Pliocene rocks (undifferentiated) yield water to domestic and stock wells in the area. In the vicinity of the Rawlins uplift, the rocks of Cambrian age, Madison limestone, and Tensleep sandstone yield water to a few public-supply wells. The Cloverly formation yields water to public-supply wells in the Miller Hill and Sage Creek basin area. Wells that tap the Madison limestone, Tensleep sandstone, and Cloverly formation yield water under sufficient artesian pressure to flow at the land surface. The Browns Park formation yields water to springs that supply most of the Rawlins city water and supply water for domestic and stock use. Included on the geologic map are location of wells and test wells, depths to water below land surface, and location of springs. Depths to water range from zero in the unconsolidated deposits along the valley of Sugar Creek at the southern end of the Rawlins uplift to as much as 129 feet below the land surface in the Tertiary sedimentary rocks along the Continental Divide in the southern part of the area. The aquifers are recharged principally by precipitation that falls upon the area, by percolation from streams and ponds, and by movement of ground water from adjacent areas. Water is discharged from the ground-water reservoir by evaporation and transpiration, by seeps and springs, through wells, and by underflow out of the area. Although most water supplies in the area are obtained from springs, some domestic, stock, and public supplies are obtained from drilled wells, many yielding water under artesian pressure, and some flowing. Dissolved solids in the water from several geologic sources, ranging from 181 to 6,660 parts per million (ppm), indicate the varied chemical quality of ground water in the Rawlins area. Water from the Cambrian rocks, Tensleep sandstone, Cloverly formation, Frontier formation, Browns Park formation, and Miocene and Pliocene rocks is generally suitable for domestic and stock use. However, water yielded to the only well sampled in the lower part of the Frontier formation contained a high concentration of fluoride. Water from the rocks mentioned above contains less than 1,000 ppm of dissolved solids but in some places may contain iron in troublesome amounts. Water from the Madison limestone and Tensleep sandstone combined, Permian rocks, and Sundance formation contains more than 1,000 ppm of dissolved solids. Water in the Sundance, Cloverly, and Frontier :formations is very soft. More ground water can be obtained in the Rawlins area than is now being used. Many springs are undeveloped, and water can be obtained from additional wells without unduly lowering ground-water levels.

Water Supply Paper↗

USGS1959

Some preliminary notes on the ground water in the Columbia River basalt

The Columbia River basalt carries ground water by percolation, largely along tabular interflow zones of variable permeability and continuity. At various places the water occurs under perched, unconfined, and confined conditions; at some places it occurs under all three conditions at different depths. Both initial and tectonic structural features, such as inclination of the flows, anticlines and synclines, and jointing and faulting, have an important bearing on occurrences of ground water in the basalt . Recharge of the ground water is most effective in areas of substantial rainfall where gravel-bedded streams cross basalt flows inclined at low angles. The basalt furnishes the main water supply for domestic and public needs and a substantial part of the water for irrigation and industry in the Columbia Plateau region. The chemical quality of the ground water is good but varies according to the geographic and geologic occurrence of the basalt rocks. The ground water is developed by thousands of wells and springs. These fall into more or less distinct types according to their construction and the occurrence of the water. There is need for improvement in techniques of construction of wells tapping confined and perched water bodies. Continued accumulation of basic geologic information is planned to guide in further development of the ground-water resources of the basalt.

Northwest Science↗

USGS2009

Geochemistry, Comparative Analysis, and Physical and Chemical Characteristics of the Thermal Waters East of Hot Springs National Park, Arkansas, 2006-09

A study was conducted by the U.S Geological Survey in cooperation with the Arkansas State Highway and Transportation Department to characterize the source and hydrogeologic conditions responsible for thermal water in a domestic well 5.5 miles east of Hot Springs National Park, Hot Springs, Arkansas, and to determine the degree of hydraulic connectivity between the thermal water in the well and the hot springs in Hot Springs National Park. The water temperature in the well, which was completed in the Stanley Shale, measured 33.9 degrees Celsius, March 1, 2006, and dropped to 21.7 degrees Celsius after 2 hours of pumping - still more than 4 degrees above typical local groundwater temperature. A second domestic well located 3 miles from the hot springs in Hot Springs National Park was discovered to have a thermal water component during a reconnaissance of the area. This second well was completed in the Bigfork Chert and field measurement of well water revealed a maximum temperature of 26.6 degrees Celsius. Mean temperature for shallow groundwater in the area is approximately 17 degrees Celsius. The occurrence of thermal water in these wells raised questions and concerns with regard to the timing for the appearance of the thermal water, which appeared to coincide with construction (including blasting activities) of the Highway 270 bypass-Highway 70 interchange. These concerns were heightened by the planned extension of the Highway 270 bypass to the north - a corridor that takes the highway across a section of the eroded anticlinal complex responsible for recharge to the hot springs of Hot Springs National Park. Concerns regarding the possible effects of blasting associated with highway construction near the first thermal well necessitated a technical review on the effects of blasting on shallow groundwater systems. Results from available studies suggested that propagation of new fractures near blasting sites is of limited extent. Vibrations from blasting can result in rock collapse for uncased wells completed in highly fractured rock. However, the propagation of newly formed large fractures that potentially could damage well structures or result in pirating of water from production wells appears to be of limited possibility based on review of relevant studies. Characteristics of hydraulic conductivity, storage, and fracture porosity were interpreted from flow rates observed in individual wells completed in the Bigfork Chert and Stanley Shale; from hydrographs produced from continuous measurements of water levels in wells completed in the Arkansas Novaculite, the Bigfork Chert, and Stanley Shale; and from a potentiometric-surface map constructed using water levels in wells throughout the study area. Data gathered from these three separate exercises showed that fracture porosity is much greater in the Bigfork Chert relative to that in the Stanley Shale, shallow groundwater flows from elevated recharge areas with exposures of Bigfork Chert along and into streams within the valleys formed on exposures of the Stanley Shale, and there was no evidence of interbasin transfer of groundwater within the shallow flow system. Fifteen shallow wells and two cold-water springs were sampled from the various exposed formations in the study area to characterize the water quality and geochemistry for the shallow groundwater system and for comparison to the geochemistry of the hot springs in Hot Springs National Park. For the quartz formations (novaculite, chert, and sandstone formations), total dissolved solids concentrations were very low with a median concentration of 23 milligrams per liter, whereas the median concentration for groundwater from the shale formations was 184 milligrams per liter. Ten hot springs in Hot Springs National Park were sampled for the study. Several chemical constituents for the hot springs, including pH, total dissolved solids, major cations and anions, and trace metals, show similarity with the shale formations

Scientific Investigations Report↗

USGS1986

Records of wells, drillers' logs, water-level measurements, and chemical analyses of ground water in Brazoria, Fort Bend, and Waller counties, Texas, 1980-84

Information on major new water wells in B razor! a, Fort Bend, and Waller Counties was compiled by the U.S. Geological Survey from 1980 through 1984. This report presents the results of the hydro!ogic data collection on new largecapacity and other selected wells, including well location and completion data, drillers' logs of the strata penetrated, water levels, and chemical quality of the produced water. These water-well data are supplementary to similar data on older wells in these counties and descriptive evaluations of the ground-water resources which have been published previously.

Texas↗

USGS1981

Surface-water resources in the Tooele 2° quadrangle, Utah

This is one of a series of maps that describe the geology and related natural resources of the Tooele 2° quadrangle. The purpose of this map is to describe on a regional scale the availability and chemical quality of surface water and to guide readers to more detailed site-specific information about the resource in this generally semiarid region. Most of the data used to compile this map were collected by the U.S. Geological Survey under cooperative programs with the Utah Departments of Natural Resources and Transportation. Those data are available in the files of the U.S. Geological Survey, Water Resources Division, Salt Lake City, Utah.

Utah↗

USGS2006

Comparison of ground-water quality in samples from selected shallow and deep wells in the central Oklahoma aquifer, 2003-2005

The aquifer units of the Central Oklahoma aquifer underlie about 2,890 square miles of central Oklahoma and are used extensively to supply water for municipal, domestic, industrial, and agricultural needs. The Central Oklahoma aquifer also is commonly referred to as the Garber-Wellington aquifer because the Garber Sandstone and Wellington Formation yield the greatest quantities of usable water for domestic and high-capacity wells. The major water-quality concerns for the Central Oklahoma aquifer described by the U.S. Geological Survey National Water Quality Assessment Program (1987 to 1992) were elevated concentrations of nitrate nitrogen in shallow water and the occurrence of arsenic, chromium, and selenium in parts of the aquifer. The quality of water from deep public-water supply wells in the Central Oklahoma aquifer is monitored by the State of Oklahoma. The chemical quality of water from shallow domestic wells is not monitored, and, therefore, there is a concern that well owners may be unknowingly ingesting water with nitrate nitrogen, arsenic, chromium, selenium, and other chemical constituents at concentrations that are considered harmful. As a result of this concern, the Oklahoma Department of Environmental Quality and the U.S. Geological Survey collaborated on a study to sample water during June 2003 through August 2005 from 23 shallow wells (less than 200 feet in depth) and 28 deep wells (200 feet or greater in depth) completed in the bedrock aquifer units of the Central Oklahoma aquifer. The objectives of the study were to describe the chemical quality of water from shallow and deep wells and to determine if the differences in constituent concentrations are statistically significant. Water from shallow wells had significantly higher concentrations of calcium, magnesium, bicarbonate, sulfate, chloride, and nitrate nitrogen than water from deep wells. There were no significant differences between concentrations of dissolved solids, sodium, and fluoride in water from shallow and deep wells. Water from 9 shallow wells had nitrate nitrogen concentrations greater than 2 milligrams per liter, suggesting nitrogen sources at land surface have had an effect on water from these wells. Water from three shallow wells (13 percent) exceeded the nitrate nitrogen maximum contaminant level of 10 milligrams per liter in drinking water. Water from shallow wells had significantly lower concentrations of arsenic, chromium, iron, and selenium than water from deep wells, whereas, concentrations of barium, copper, manganese, and zinc were similar. Water-quality data indicate that arsenic frequently occurs in shallow ground water from the Central Oklahoma aquifer, but at low concentrations (<10 micrograms per liter). The occurrence of chromium and selenium in water from shallow wells was infrequent and at low concentrations in this study. It does not appear that the quality of water from a shallow well can be predicted based on the quality of water from a nearby deep well. The results show that in general terms, shallow ground water has significantly higher concentrations of most major ions and significantly lower concentrations of arsenic, chromium, and selenium than water from deep wells.

Scientific Investigations Report↗

USGS1991

Records of wells, drillers' logs, water-level measurements, and chemical analyses of ground water in Brazoria, Fort Bend, and Waller Counties, Texas, 1985-89

Data for water wells and ground water in Brazoria, Fort Bend, and Waller Counties were collected during 1985-89 by the U.S. Geological Survey. This report presents a compilation of records for 32 wells in Brazoria County, 19 wells in Fort Bend County, and 16 wells in Waller County. Drillers' logs for 65 wells, water levels for 85 wells, chemical analyses of water for 9 wells, and water levels and chemical analyses of water from previously inventoried wells also are presented in this report.

Texas↗

USGS2012

Biotic, water-quality, and hydrologic metrics calculated for the analysis of temporal trends in National Water Quality Assessment Program Data in the Western United States

The U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program was established by Congress in 1991 to collect long-term, nationally consistent information on the quality of the Nation's streams and groundwater. The NAWQA Program utilizes interdisciplinary and dynamic studies that link the chemical and physical conditions of streams (such as flow and habitat) with ecosystem health and the biologic condition of algae, aquatic invertebrates, and fish communities. This report presents metrics derived from NAWQA data and the U.S. Geological Survey streamgaging network for sampling sites in the Western United States, as well as associated chemical, habitat, and streamflow properties. The metrics characterize the conditions of algae, aquatic invertebrates, and fish. In addition, we have compiled climate records and basin characteristics related to the NAWQA sampling sites. The calculated metrics and compiled data can be used to analyze ecohydrologic trends over time.

Open-File Report↗