USGS Science⌕ Search

SEARCH · USGS Science

Results for “The Planetary Science Journal”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,665 records · Page 55Linked to original sources
USGS2026

Simulation of groundwater flow in the Silurian aquifer, eastern Iowa, 2020–45

The Silurian aquifer is an important water source for municipalities, industry, and rural households and communities in eastern Iowa, including Johnson County. Increasing demand for groundwater from the aquifer indicated that analytical tools may be beneficial to quantify groundwater resources and inform water-management decisions for the aquifer. The U.S. Geological Survey, in cooperation with the Johnson County Board of Supervisors, developed conceptual and numerical groundwater models to simulate water levels in the Silurian aquifer, determine groundwater budgets, and forecast changes in groundwater levels through 2045. A MODFLOW numerical model was constructed to match water levels for 2020 through 2022. Model performance was assessed by comparing simulated and observed water-level hydrographs at several pumping and monitoring wells. Hydrograph comparison indicates that the model simulates water levels accurately at monitoring wells that are not near areas of pumping and generally overpredicts water levels near pumping wells, while accurately simulating the drawdown trend over time at pumping wells. This transient model framework was then used to predict water levels through 2045 in a scenario of moderate drought and increased groundwater withdrawals. Results from the predictive model indicate as much as 13 meters of additional drawdown in 2045 from 2020 water levels in the area of pumping wells.

Iowa↗
USGS2026

Ground-motion simulations for the 2024 Mw 4.8 Tewksbury, New Jersey, earthquake

Ground-motion simulations of notable earthquakes in the central and eastern United States are limited and typically assume one-dimensional (1D) Earth structure. In this study, we use a three-dimensional (3D) seismic velocity model to better constrain the depth and focal mechanism of the April 5th, 2024, moment magnitude 4.8 Tewksbury earthquake and investigate the spatial variability of earthquake ground motions and the effects of nearby sedimentary basins. We perform earthquake ground-motion simulations up to 0.5 Hz using the 3D spectral-element wave-propagation solver SPECFEM3D over a region 280-km wide by 260-km long by 77-km deep. Topography and subsurface geophysical structure are assigned using the U.S. Geological Survey National Crustal Model with a minimum shear-wave velocity of 200 m/s. We use earthquake time series from 13 broadband seismic stations in the region that have a uniform azimuthal distribution and epicentral distances ranging from 76 to 131 km to compare with synthetics and explore the effects of 1D versus 3D seismic structure on focal mechanism and depth solutions. Ground-motion intensity metrics are also presented relative to the NGA-East ground-motion models (GMMs) currently used in seismic hazard assessments for the region. We find that the 3D model, which reveals a wide spatial variability of period-dependent ground motions, yields better predictions of earthquake ground motions relative to the 1D model and the NGA-East ergodic ground-motion model, with 76 percent reduction of residual variance in observed ground motions averaged over 3-, 5-, 7-, and 10-second periods. Use of the 3D model to solve for a focal mechanism yields a shallower focal depth at 4 km and a shallower east-dipping focal plane relative to the U.S. Geological Survey regional moment tensor and Global Centroid Moment Tensor. Our study demonstrates that use of 3D seismic velocity models can improve estimates of earthquake focal mechanisms, ground motions, and seismic hazard.

New Jersey↗
USGS2026

Simulation of groundwater flow to evaluate hydrogeologic controls on a PFAS plume, Coakley Landfill Superfund site, Rockingham County, New Hampshire

Per- and polyfluoroalkyl substances (PFAS), including perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS), have been detected at combined concentrations above 2,000 nanograms per liter (ng/L) at groundwater seep locations near the Coakley Landfill Superfund site, in North Hampton, New Hampshire. The landfill was active from 1972 to 1985. An impermeable cap was placed on the landfill in 1998. The adjacent area to the Coakley Landfill has many water supply wells, and transport of PFAS compounds to the wells is a concern. Fracture anisotropy in the underlying bedrock aquifer complicates the understanding of PFAS transport because groundwater preferentially travels along fractures that may not align with the prevailing groundwater flow direction. In 2018, the U.S. Environmental Protection Agency and the U.S. Geological Survey began an investigation of the groundwater flow from the Coakley Landfill site. This report describes the modification of a numerical groundwater-flow model for the local area around the Coakley Landfill and summarizes findings of the investigation. In addition, this report includes a brief description of PFOA and PFOS occurrence, a discussion of model construction, evaluation of model performance through calibration, and discussion of simulation results for two periods (before and after capping). Limitations are also discussed. Results show that simulated groundwater flow moves from the Coakley Landfill to the west and north. Advective transport modeling using particle tracking shows that groundwater from the landfill discharges primarily to streams to the west and north, and a small amount is transported to distal wells. Dilution of contaminants through advection and dispersion likely plays a role in whether PFAS compounds from the landfill will be detected above laboratory reporting levels at distal wells.

New Hampshire↗
USGS2025

Increased flood exposure in the Pacific Northwest following earthquake-driven subsidence and sea-level rise

Climate-driven sea-level rise is increasing the frequency of coastal flooding worldwide, exacerbated locally by factors like land subsidence from groundwater and resource extraction. However, a process rarely considered in future sea-level rise scenarios is sudden (over minutes) land subsidence associated with great (>M8) earthquakes, which can exceed 1 m. Along the Washington, Oregon, and northern California coasts, the next great Cascadia subduction zone earthquake could cause up to 2 m of sudden coastal subsidence, dramatically raising sea level, expanding floodplains, and increasing the flood risk to local communities. Here, we quantify the potential expansion of the 1% floodplain (i.e., the area with an annual flood risk of 1%) under low (~0.5 m), medium (~1 m), and high (~2 m) earthquake-driven subsidence scenarios at 24 Cascadia estuaries. If a great earthquake occurred today, floodplains could expand by 90 km 2 (low), 160 km 2 (medium), or 300 km 2 (high subsidence), more than doubling the flooding exposure of residents, structures, and roads under the high subsidence scenario. By 2100, when climate-driven sea-level rise will compound the hazard, a great earthquake could expand floodplains by 170 km 2 (low), 240 km 2 (medium), or 370 km 2 (high subsidence), more than tripling the flooding exposure of residents, structures, and roads under the high subsidence scenario compared to the 2023 floodplain. Our findings can support decision-makers and coastal communities along the Cascadia subduction zone as they prepare for compound hazards from the earthquake cycle and climate-driven sea-level rise and provide critical insights for tectonically active coastlines globally.

California, Oregon, Washington↗
USGS2025

Natural source zone depletion of crude oil in the subsurface: Processes controlling mass losses of individual compounds

At many petroleum hydrocarbon spill sites, residual spilled product forms a long-term source of groundwater contamination. The phrase source zone natural depletion is used to refer to the mass loss rates. Overall mass lost under environmental conditions was analyzed using conservative biomarker concentrations for a 1979 oil spill in northern Minnesota, USA. After 40–41 years, an average of 50% of the mass was lost with values ranging from 22% to 57% depending on location. It is also important to understand the composition changes in the source. To understand controls on the losses of individual compounds, concentrations of volatile hydrocarbons in oil samples were compared with aqueous solubilities, and pore-space oil saturations. The results of the comparison show that losses of the oil compounds were controlled by pore-space oil saturations, solubility, and susceptibility to degradation under methanogenic conditions. Compounds that degrade under methanogenic conditions, including toluene, o -xylene, and n -alkanes are more depleted compared to benzene, ethylbenzene, and m - and p -xylene for which losses are dominated by dissolution. These rates and compound-specific behaviors form a foundation for improved modeling approaches and risk analyses.

Minnesota↗
USGS1976

Corwin Springs Known Geothermal Resources Area, Park County, Montana

The Corwin Springs Known Geothermal Resources Area (KGRA) is contiguous to Yellowstone National Park along a part of the northern boundary of the park near Gardiner, Park County, Mont. The area contains two known sites of hot-spring activity--LaDuke Spring, 2.8 km southeast of the small resort community of Corwin Springs, and Bear Creek Spring, 2.6 km east of Gardiner. LaDuke Spring issues from brecciated quartzite and has a flow rate of 380 1/min, a surface water temperature of 65°C, a silica-geothermometer temperature of 68.7°C, and a Na-K-Ca geothermometer temperature of 76.8°C. Bear Creek Spring issues from limestone and has a flow rate of 4 1/min, a surface water temperature of 32°C, a silica temperature of 46.7°C, and a Na-K-Ca temperature of 87.2°C. The springs, which are actively depositing travertine, are on or near the trace of the Gardiner fault-a high-angle reverse fault which forms the southwestern boundary of the Beartooth uplift. Features that make the Corwin Springs KGRA potentially significant include: (1) Proximity of the Corwin Springs area to significant Pliocene and Pleistocene volcanism in Yellowstone National Park and related geothermal activity, (2) existence of a large potential geothermal reservoir in the northern extension of the Sepulcher Mountain graben, (3) localization of thermal activity along the Gardiner fault in the Corwin Springs area, (4) occurrence of negative gravity anomaly centered over the northern end of the Sepulcher Mountain graben, (5) existence of negative magnetic anomaly in the Corwin Springs area, (6) location of the area within the Intermountain seismic belt, (7) evidence of recent tectonism in the area, as demonstrated by Pleistocene and Holocene faulting, and (8) observed surface temperatures and estimated geochemical temperatures of the two known hot springs (features which do not indicate high subsurface temperatures).

Montana↗
USGS2026

Geochemical geodatabase of sedimentary strata (coal, coal-adjacent rocks, tuffaceous oil shale, phosphate-rich rocks) and produced water in the Uinta region, Utah and Colorado

The Geochemical Geodatabase of Sedimentary Strata (Coal, Coal-adjacent Rocks, Tuffaceous Oil Shale, Phosphate-rich Rocks) and Produced Water in the Uinta Region, Utah and Colorado, consists of compiled datasets acquired as part of the Carbon Ore, Rare Earth, and Critical Mineral (CORE-CM) Uinta Region assessment funded by the U.S. Department of Energy (DEFE0032046, 2021–2024; Birgenheier et al., 2024). The CORE-CM assessment focused on providing comprehensive geological and geochemical characterization of current and prospective sedimentary-hosted resources including coal, oil shale, phosphatic limestone, and produced water from oil and gas targets present in eastern Utah and northwestern Colorado (Figure 1). This Data Series includes a geodatabase that consists of analytical geochemical data collected September 2021 through December 2024 via portable X-ray fluorescence (pXRF), and laboratory measured analyses produced by inductively coupled plasma mass spectrometry (ICP-MS) and inductively coupled plasma optical emission spectroscopy (ICP-OES). The coal-related geochemical data are derived primarily from the Cretaceous Blackhawk Formation and Ferron Sandstone of Utah, and the Mesaverde Group of Colorado. Additional non-coal resources assessed include oil shale-bearing strata of the Eocene upper Green River Formation (Utah and Colorado), phosphate-rich limestone of the Permian Park City Formation (Utah) and produced water from oil and gas-bearing strata of the Eocene Green River and Wasatch Formations (Uinta Basin) and the Pennsylvanian Paradox Formation (Paradox Basin) (Table 1). The CORE-CM assessment included a wide range of lithologies present in the coal, oil shale, and phosphate geologic resource systems whether or not the specific lithology has current economic value. Geochemical analyses of produced water from oil and gas wells focused on current and emerging hydrocarbon targets in the central Uinta Basin and northern Paradox Basin. A total of 13,092 geochemical analyses from these geologic systems is provided in the included geodatabase. A series of coal quality data (e.g., composition and maceral analyses) is also included in the database and was digitized from archived coal samples from the Utah Geological Survey (Appendix A).

Colorado, Utah↗
USGS1992

Public water-supply systems and water use in Tennessee, 1988

This report summarizes the results of a study conducted by the U.S. Geological Survey, in cooperation with the Tennessee Department of Environment and Conservation (TDEC), Division of Water Supply in 1988. Data gathered during an inventory by the TDEC were collated to determine water use, supply sources, population served, and design and storage capacities of the systems. The inventory was limited to systems that were active on June 30, 1988. Results of a survey of the systems conducted by the Tennessee Department of Health and Environment during 1988 were a primary source of data for this report. Data from computer and manual files maintained by the Tennessee Department of Health and Environment and the U.S. Geological Survey also were used. The Division of Water Supply, TDEC, surveyed 541 public water-supply systems. These systems served 81 percent of the population of the State, or 3.95 million people. The gross per capita use statewide for public-supplied water was 179 gallons per day. Total water withdrawals for public supply increased about 39 percent from 510 million gallons per day (Mgal/d) in 1980, to 708 Mgalld in 1988. During the same period, the population increased about 7 percent. Surface-water withdrawals accounted for 63 percent (446 Mgal/d) of the total water withdrawn in the State. All of these withdrawals occurred in the Tennessee (56 percent or 249 Mgal/d) and the Ohio (44 percent or 197 Mgalld) hydrologic regions. Ground water supplied 262 Mgal/d or 37 percent of the total water withdrawn by public-supply systems statewide. Of that amount, 79 percent, or 208 Mgalld, was used in western Tennessee.

Tennessee↗
USGS2024

Hydrologic investigations and a preliminary conceptual model of the groundwater system at North Penn Area 1 Superfund Site, Souderton, Montgomery County, Pennsylvania

The U.S. Geological Survey (USGS) conducted hydrogeologic investigations, reviewed existing data, and developed a preliminary conceptual model of the groundwater system as part of technical support of the U.S. Environmental Protection Agency (EPA) at the North Penn Area 1 Superfund Site (hereafter, the NP1 Site) located within the Borough of Souderton in Montgomery County, Pennsylvania. Field work and monitoring took place during 2012–18. The area is underlain by sedimentary formations that form a fractured-rock aquifer used for drinking water and industrial supply. The EPA placed the Site on the National Priorities List in 1989, identifying tetrachloroethylene (PCE) and trichloroethylene (TCE) as contaminants of concern. During 2012–18, the USGS conducted field activities that included drilling an 82-foot (ft)-deep monitoring well (MG 2220) in 2016, reconstructing a 208-ft-deep former industrial production well (MG 668 [Granite Knitting Mill]), and collecting borehole geophysical and video logs and water levels from those and five additional wells, which ranged in depth from about 50 to 200 ft below land surface. Continuous water levels were collected during 2014–17, and a synoptic set of water levels were measured in April 2018 in the seven wells. The borehole geophysical logs (caliper, acoustic televiewer, natural gamma, single-point resistance, vertical flow, and fluid temperature and resistivity) and borehole video logs in the seven wells were evaluated to assess potential for lithologic correlation and to identify and describe water-bearing features, which included both low- and high-angle fractures and other openings oriented along dipping bedding planes, joints, or possible faults. Borehole geophysical logs collected by USGS in 1992 in a 300-ft-deep former production well near the Site were also evaluated. Few to no distinctive features were identified on geophysical logs (natural gamma and single-point resistance) that could be used for correlation, thus limiting this approach to determining local geologic structure. Extensive fracturing in the upper 62 ft of monitoring well MG 2220 indicates that the well was likely drilled through a zone of faulting, and other evidence of faulting is present in the area near the Site. Assessment of continuous water levels showed hydraulic connections among some wells as indicated by rising or falling water levels in response to changes in pumping rates at nearby wells. A map of water levels measured in April 2018 indicates potential for groundwater flow generally toward the stream to the south and southwest of the Site, but the limited water-level data are insufficient to describe vertical groundwater gradients or lateral gradients in any detail. Review of 1999–2022 volatile organic compound (VOC) monitoring data collected by the Pennsylvania Department of Environmental Protection for five monitoring wells indicates that the highest groundwater concentrations of PCE and TCE were found in samples from extraction well MG 2201 (S-1) downgradient from, and nearest to, the previously identified Site contaminant source area, and these concentrations fluctuated through time. PCE concentrations were higher than TCE concentrations in samples from all five monitoring wells and were much higher than TCE concentrations in samples from extraction well MG 2201 (S-1). Temporally variable recharge is a possible factor affecting observed fluctuations in PCE concentrations in groundwater samples from well extraction MG 2201 (S-1), as indicated by a general inverse relation between PCE concentrations and water levels in a nearby long-term observation well. The PCE concentration of 1,830 micrograms per liter (μg/L) in a May 2018 water sample from monitoring well MG 2220 was more than four times the PCE concentration of 444 μg/L in a December 2017 sample from the nearby extraction well MG 2201 (S-1), which is open to fewer fractures. Low concentrations of VOCs were measured in surface water at two stream sites downgradient from wells with the highest groundwater VOC concentrations at the Site, indicating that discharge of contaminated groundwater to the stream is likely. Development of a conceptual model of the groundwater system was constrained by limited data. In areas with no pumping, groundwater-flow directions generally are thought to be controlled by topography and geologic structure (bedding orientation) and likely to the south and southwest of the Site, with local flow directions affected by orientations of fractures, joints, and local faults. Additional investigations that could help improve the conceptual model of the groundwater system and help delineate the extent of groundwater contamination and its transport are discussed.

Pennsylvania↗
USGS2025

Estimating agricultural irrigation water consumption for the High Plains aquifer region with integrated energy- and water-balance evapotranspiration modeling approaches

Estimation of irrigation water use provides essential information for the management and conservation of agricultural water resources. Conventionally, water use data are created based on reports and surveys from water users, whereas manual records may not be complete due to lacking flow meters, measurement gaps, inconsistent methods across regions, and time- and cost-consuming data processing. Alternatively, spatially explicit estimation of irrigation water use can be conducted efficiently using remote sensing evapotranspiration (ET) modeling approaches. In this study, we created a gridded blue water evapotranspiration (BWET) dataset to estimate historical irrigation water consumption (1986 – 2020) in the croplands across the United States High Plains aquifer region. The BWET data were generated by integrating an energy-balance ET model [Operational Simplified Surface Energy Balance model (SSEBop)] and a water-balance ET model [Vegetation ET model (VegET)]. BWET in croplands indicates crop consumptive use of irrigation water extracted from surface water and groundwater resources. The BWET estimates were compared with reported irrigation water use data for all counties within the aquifer region. The results revealed high agreement between growing season (May – September) BWET and annual water withdrawal at county level. Specifically, correlation coefficients of volumetric BWET and water withdrawal were 0.90 and 0.96, respectively, for the entire aquifer region and western Kansas. The timeseries of BWET and water withdrawal showed similar temporal trends and high covariations. The BWET estimates were systematically lower than the water withdrawal measurements, which was primarily attributed to blue water losses in the irrigation system. The irrigation efficiency, calculated as the ratio of BWET to water withdrawal depth, was 0.57 and 0.74 for the entire aquifer region and western Kansas, respectively. This study demonstrates the capability of using satellite-based ET models (e.g., SSEBop and VegET) to efficiently estimate crop water consumption and evaluate irrigation efficiency at landscape, county, and regional scales.

Colorado, Kansas, Nebraska, New Mexico, Oklahoma, ↗
USGS2024

Comparing subduction ground-motion models to observations for Cascadia

We evaluate Cascadia subduction ground-motion models (GMMs), considered for the 2023 US National Seismic Hazard Model (NSHM) update, by comparing observations to model predictions. The observations comprise regional recordings from intraslab earthquakes, including contributions from 2021 and 2022 events in southern Cascadia and global records from interface earthquakes. Since the 2018 NSHM update, new GMMs for Cascadia have been published by the Next Generation Attenuation (NGA)-Subduction Project that require independent evaluation. In the regional intraslab comparisons, we highlight a characteristic frequency dependence for Cascadia data, with short periods having lower ground motions and longer periods being comparable to other subduction zones. We evaluate differences in northern and southern Cascadia and find that the NGA-Subduction GMMs developed using southern Cascadia data perform better in this region than the model that did not consider these data. We compare ground-motion variability in Cascadia with the NGA-Subduction model predictions and find differences at short periods ( T = 0.1 s) due to the use of global versus regional data in the development of these models. Moreover, the within-event component of aleatory variability from the GMMs overpredicts the standard deviation of Cascadia recordings at very short periods ( T < 0.05 s). Using global interface earthquakes as a proxy to evaluate the Cascadia GMMs, we find long-period overprediction from a simulation-based GMM and some of the empirical GMMs. When comparing recent observations, we find a similar misfit to GMMs and the 2010 and 2022 Ferndale earthquakes. Finally, we observe different basin amplification factors arising in different subsets of the data, which indicate that differences in basin factors between empirical GMMs could arise from the data selection choices by the developers. As part of evaluating the regional basin terms, we apply basin amplification factors from the magnitude 9 Cascadia earthquake simulations to the empirical GMMs for interface earthquakes. The comparisons presented in this study indicate that the NGA-Subduction GMMs for Cascadia perform well relative to observations and older subduction GMMs.

British Columbia, California, Oregon, Washington↗
USGS2026

Simulation-based scenario ShakeMaps for large magnitude (MW6.5+) crustal earthquakes on the Seattle, Tacoma, and southern Whidbey Island faults, Washington, USA

Scenario ground‐motion maps based on empirical ground‐motion models (GMMs) provide a rapid and generally reliable means of estimating the amplitude and distribution of earthquake shaking. However, because GMMs are designed for broad applicability, they often rely on simplified representations of Earth structure, which can limit their accuracy in regions with complex source, path, and site effects. This can substantially impact the accuracy of predicted shaking in areas like western Washington State, where deep, interconnected basin structure exerts a strong influence on seismic‐wave propagation. In this study, we present a new suite of simulation‐based scenario ShakeMaps that characterize ground shaking from large‐magnitude ( ⁠ M W 6.5–7.5) earthquakes on the Seattle, Tacoma, and southern Whidbey Island faults. These maps are developed using results from recent 3D wave propagation simulations ( Stone et al. , 2022 , 2023 , 2025 ) that incorporate realistic rupture geometries, variable slip distributions, and a regional 3D seismic velocity model with shallow soils. Broadband ground motions are estimated by combining the low‐frequency (<1 Hz) deterministic seismograms from these studies with high‐frequency (1–10 Hz) stochastic seismograms. Simulated ground motions are corrected to account for the enforced minimum shear‐wave velocity and nonlinear site response. The resulting ShakeMaps represent median ground‐shaking estimates derived from multiple rupture scenarios with varying slip distributions and hypocenter locations for each fault. To extend ShakeMap coverage beyond the simulation domain (i.e., into eastern Washington, northern Oregon, and southwestern British Columbia), we scale GMM‐based ground‐motion estimates using amplification patterns observed in the simulations. These new ShakeMaps reveal the substantial influence of deep basin structure on shaking intensity, underscoring the importance of considering crustal structure complexity in regional hazard assessments for the Pacific Northwest.

Washington↗
USGS2026

Selected water-quality data from the Cedar River and Cedar Rapids well fields, Cedar Rapids, Iowa, 2017–22

The Cedar River alluvial aquifer is the source of drinking water in Cedar Rapids, Iowa. Production wells are completed in the alluvial aquifer approximately 40 to 80 feet below land surface. The City of Cedar Rapids and the U.S. Geological Survey have studied the groundwater-flow system and water quality of the aquifer in the vicinity of Cedar Rapids since 1992. Results of these studies documented hydrologic conditions, water quality, and geochemistry of the alluvial aquifer and interactions with the Cedar River. Water-quality samples were collected for studies involving well field monitoring, trends, source-water protection, groundwater geochemistry, surface-water–groundwater interaction, and pesticides in groundwater and surface water. Water quality was analyzed for dissolved major ions (boron, bromide, calcium, chloride, fluoride, iron, magnesium, manganese, potassium, silica, sodium, sulfate, and total dissolved solids), dissolved nutrients (ammonia as nitrogen, ammonia plus organic nitrogen as nitrogen, nitrite plus nitrate as nitrogen, nitrite as nitrogen, orthophosphate as phosphorus, and phosphorus), dissolved organic carbon, and selected pesticides. Physical characteristics (alkalinity, dissolved oxygen, pH, specific conductance, and water temperature) were measured on site and recorded for each water sample collected. This report presents the results of routine water-quality data-collection activities from October 2017 through September 2022. Methods of data collection, quality assurance, water-quality analyses, and statistical procedures are presented. Data include the results of water-quality analyses from quarterly sampling from monitoring wells, production wells, two water treatment plants, and the Cedar River at Blairs Ferry Road at Palo, Iowa, streamgage (U.S. Geological Survey station number 05464420), as well as monthly nutrient sampling from the Cedar River and Morgan Creek near Covington, Iowa, streamgage (U.S. Geological Survey station number 05464475).

Iowa↗
USGS1976

Geotechnical description of four Mississippi Delta soil borings

The submerged portion of the Mississippi Delta complex forms an ideal natural laboratory to study the effects of rapid deposition. One of the most obvious of these effects is the mass movements of sediments. Slump and slide signatures, mudflow characteristics, and evidence for creep are all found in abundance on the delta platform. These types of features have been studied by Colemen and Wright (1974) with regard to form and by Garrison (1974) with regard to their spatial distribution. Assembling these authors' findings, it is clear that the entire offshore zone contiguous with the Mississippi River is a myriad of geological action. This situation is indeed stimulating to the sedimentologist, yet it represents a nightmare to the foundation engineer. Emplacing offshore structures in such an environment is a most difficult task, particularly since the high degree of local variability dictates that each case must be handled separately. It is under these circumstances that a marriage between geology and engineering is most fruitful, for determining the relationships between the sedimentological processes and the engineering properties is satisfying to parties from both disciplines. This, then, is the underlying objective of the Mississippi Delta research project. By investigating the instability in a geologic sense, it is hoped that many of the engineering problems will become more soluble and that extrapolation and prediction will become more realistic.

Mississippi Delta↗
USGS2024

Estimated groundwater recharge for mid-century and end-of-century climate projections, Kaua‘i, O‘ahu, Moloka‘i, Lāna‘i, Maui, and the Island of Hawai‘i

Demand for freshwater in the State of Hawaiʻi is expected to increase by roughly 13 percent from 2020 to 2035. Groundwater availability in Hawaiʻi is affected by a number of factors, including land cover, rainfall, runoff, evapotranspiration, and climate change. To evaluate the availability of fresh groundwater under projected future-climate conditions, estimates of groundwater recharge are needed. A water-budget model with a daily computation interval was used to estimate the spatial distribution of groundwater recharge for Kauaʻi, Oʻahu, Molokaʻi, Lānaʻi, Maui, and the Island of Hawaiʻi for recent climate conditions and three future-climate scenarios. Climate conditions from 1978 to 2007 were used as the reference period for recent climate conditions on each island. The three future-climate scenarios were developed using available high-resolution downscaled climate projections that include (1) a mid-century scenario using projected rainfall conditions for the Representative Concentration Pathway (RCP) scenario during 2041–71 with a total radiative forcing of 8.5 watts per square meter by the year 2100 (RCP8.5 2041–71 scenario), (2) a dry-climate scenario using projected rainfall conditions for the RCP8.5 scenario during 2071–99, and (3) a wet-climate scenario using projected rainfall conditions for the “Special Report on Emissions Scenarios” A1B scenario during 2080–99 for Maui, the RCP4.5 scenario during 2080–99 for Kauaʻi, Lānaʻi, and the Island of Hawaiʻi, and the RCP8.5 scenario during 2080–99 for Oʻahu and Molokaʻi. An additional drought scenario was added for Lānaʻi to assess the effect of extreme drought conditions during 2008–12 on groundwater recharge. All scenarios used 2020 land cover. Mean annual groundwater recharge is estimated to decrease between 5 and 55 percent on all six islands in this study for the mid-century and dry-climate scenarios relative to the reference-period recharge. Recharge is estimated to increase for Kauaʻi, Oʻahu, Molokaʻi, Lānaʻi, and Maui between 2 and 43 percent and decrease for the Island of Hawaiʻi by about 4 percent for the wet-climate scenario. Comparing the mid-century and dry-climate scenarios, all 110 aquifer systems (management areas defined by the State of Hawaiʻi Commission on Water Resource Management) from all six islands show similar direction in drying (104 aquifer systems) or wetting (6 aquifer systems) changes for recharge. However, among the three future scenarios, only 35 of 110 aquifer systems show similar direction in drying (30 aquifer systems) or wetting (5 aquifer systems) changes for recharge.

Hawaii↗
USGS2025

Combining multisite tsunami and deformation modeling to constrain slip distributions for the 1700 C.E. Cascadia earthquake

A major earthquake ruptured the Cascadia subduction zone (CSZ) on 26 January 1700. Key paleoseismic evidence associated with this event include tsunami deposits, stratigraphic evidence of coastal coseismic subsidence, written Japanese records of a tsunami unaccompanied by earthquake shaking, and margin‐wide turbidites found offshore and in lacustrine environments. Despite this wealth of independent clues, important details about this event remain unresolved. Dating uncertainties do not conclusively establish whether the proxies are from one earthquake or a sequence of them, and we have limited knowledge of the likely slip distributions of the event or events. Here, we use a catalog of 37,500 candidate synthetic ruptures between M w 7.8 and 9.2 and simulate their resulting coseismic deformation and tsunami inundation. Each model is then compared against estimated Japan tsunami arrivals, regional coastal subsidence records, and local paleotsunami deposits mapped at six different coastal marshes and one coastal lake along the CSZ. We find that seven full‐margin ruptures with a median magnitude of M w 9.1 satisfy all three constraints. We favor one M w 9.11 model that best matches all site paleoseismic observations and suggests that the Cascadia megathrust slipped up to ∼30 m and must have shallow geodetic coupling. We also find that some sequences composed of three or four ruptures can still satisfy the observations, yet no sequences of two ruptures can. Sequences are differentiated into three groups based on whether they contain a mainshock rupture located in the south (>44° N) or further north. All sequences contain unruptured portions of the megathrust and most contain mainshocks with peak slip above 40 m. The fit of the geologic evidence from sequences is poor in comparison to single‐event models. Therefore, sequences are generally less favored compared to full‐margin events.

British Columbia, California, Oregon, Washington↗
USGS2024

Estimation of reservoir storage capacity and geomorphic change detection analysis from a multibeam bathymetric survey of Randy Poynter Lake, Rockdale County, Georgia

Rockdale County Department of Water Resources has a directive to update estimates of the reservoir storage capacity of Randy Poynter Lake, located in northern Georgia, and to assess recent sedimentation and associated storage capacity loss. In 2022, the U.S. Geological Survey completed a multibeam bathymetric survey of Randy Poynter Lake to update storage capacity estimates and to quantify storage capacity change since the first multibeam bathymetric survey in 2012 in consideration of estimated errors inherent to bathymetric surveys. Data from the 2022 survey were used to generate contours of the reservoir as well as compute storage capacity at regular increments of water-surface elevation. Storage capacity comparisons between 2012 and 2022 at Randy Poynter Lake show minimal changes that are within the estimated uncertainties, with consistent or slightly increased storage capacities observed at most water-surface elevations and reductions observed at the remaining few elevations. Comparison of the multibeam bathymetric data collected in 2012 with data collected in 2022 further allowed for a formal geomorphic change detection analysis to map, quantify, and infer causation of morphological change over time with respect to a level of detectable change. The volume change in Randy Poynter Lake for the decade between 2012 and 2022 was slightly net-depositional and within the estimated uncertainty. The spatial distribution of sediment deposition was primarily concentrated in the northern portion of the lake, where the principal tributary flows into Randy Poynter Lake. The results of the geomorphic change analysis were used to further understand the future implications to storage capacity change. Despite the challenges of confirming systematic biases because of uncertainties exceeding the observed changes, insights from the study help predict long-term reservoir sediment accumulation, indicating a reservoir half-life extending about 650 years from 2022 on the basis of the current sediment yield estimates.

Georgia↗