USGS Science⌕ Search

SEARCH · USGS Science

Results for “Marine Ornithology: Journal of Seabird Research and Conservation”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,688 records · Page 53Linked to original sources
USGS1999

Comparison of two approaches for determining ground-water discharge and pumpage in the lower Arkansas River Basin, Colorado, 1997-98

In March 1994, the Colorado Division of Water Resources (CDWR) adopted “Rules Governing the Measurement of Tributary Ground Water Diversions Located in the Arkansas River Basin” (Office of the State Engineer, 1994); these initial rules were amended in February 1996 (Office of the State Engineer, 1996). The amended rules require users of wells that divert tributary ground water to annually report the water pumped monthly by each well. The rules allow a well owner to report the pumpage measured by a totalizing flowmeter (TFM) or pumpage determined from electrical power data and a power conversion coefficient (PCC) (Hurr and Litke, 1989). Opinions by representatives of the State of Kansas, presented before the Special Master hearing a court case [State of Kansas v. State of Colorado, No. 105 Original (1996)] concerning post-Compact well pumping, stated that the PCC approach does not provide the same level of accuracy and reliability as a TFM when used to determine pumpage. In 1997, the U.S. Geological Survey (USGS), in cooperation with the CDWR, began a 2-year study to compare ground-water pumpage estimates made using the TFM and the PCC approaches. The study area was along the Arkansas River between Pueblo, Colorado, and the Colorado-Kansas State line (fig. 1). The two approaches for estimating ground-water discharge and pumpage were compared for more than 100 wells completed in the alluvial aquifer of the Arkansas River Basin. The TFM approach uses an inline flowmeter to directly measure instantaneous discharge and the total volume of water pumped at a well. The PCC approach uses electrical power consumption records and a power conversion coefficient to estimate the pumpage at ground-water wells. This executive summary describes the results of the comparison of the two approaches. Specifically, (1) the differences in instantaneous discharge measured with three portable flowmeters and measured with an inline TFM are evaluated, and the statistical differences in paired instantaneous discharge between the two approaches are determined; (2) short- and long-term variations in the PCC’s are presented; (3) differences in pumpage between the two approaches are evaluated, and the statistical differences in pumpage between the two approaches are determined; (4) potential sources of discrepancy between pumpage estimates are discussed; and (5) differences in total network pumpage using the two approaches are presented. During the irrigation seasons of 1997 and 1998, instantaneous discharge and electrical power demand were measured at randomly selected wells to determine PCC’s. At more than 100 wells, the PCC’s determined during the 1998 season were applied to total electrical power consumption data that was recorded between the initial and final readings at each network well site in 1998 to estimate total ground-water pumpage. At each site, an inline TFM was installed in a full-flowing, acceptable test section of pipe on the discharge side of the pump where the measurement of discharge was made. Measurements of instantaneous ground-water discharge also were made using three different types of portable flowmeters. The average velocity multiplied by the cross-sectional area of the discharge pipe was used to compute the discharge in gallons per minute. Whenever possible, discharge measurements were made at each network site using all three types of portable flowmeters.

Colorado↗
USGS2025

How do hydrological variability and human activities control the spatiotemporal changes of riverine nitrogen export in the Upper Mississippi River Basin?

Excessive nitrogen export from agricultural watersheds remains a critical water quality challenge, with the Upper Mississippi River Basin (UMRB) significantly contributing to downstream eutrophication and hypoxia in the Gulf. This study investigates the spatiotemporal dynamics of riverine nitrate plus nitrite (NO 3 – + NO 2 – -N) export across the UMRB at high spatial resolution (12-digit Hydrologic Unit Codes or HUC12 subwatershed scale) during 2001–2020 and quantifies the effects of anthropogenic activities and hydrological variability on riverine NO 3 – + NO 2 – -N export changes in the region between 2001–2005 and 2016–2020. Our results revealed hotspots of substantial increases in NO 3 – + NO 2 – -N yields across the UMRB, with distinct regional patterns in driving factors. Over the entire UMRB, NO 3 – + NO 2 – -N yields increased by 9.7 kg/ha/yr on average from 2001–2005 to 2016–2020, with anthropogenic activities contributing 4.8 kg/ha/yr and hydrological variability contributing 4.9 kg/ha/yr. The northern and western UMRB had combined influences from both anthropogenic activities and hydrological variability, while the east-central regions had predominantly hydrologically driven changes. Agricultural sources, including fertilizer, manure, and biological nitrogen fixation, collectively contributed over 80% of NO 3 – + NO 2 – -N loading throughout the basin. This framework for disentangling human and hydrological impacts provides critical insights for developing effective and targeted watershed management strategies to reduce nutrient losses and improve water quality.

Upper Mississippi River Basin↗
USGS2025

Airborne radiometric data map alteration of porphyry copper systems in the Elkhorn district, MT

The Elkhorn district in southwestern Montana is known for past production of high-grade base and precious metals from skarn and carbonate replacement deposits. The district also hosts a porphyry Cu-Mo deposit. A radiometric survey flown over the district and surrounds provides maps of surficial concentrations of potassium, thorium, and uranium. Handheld gamma ray spectrometer measurements on altered and unaltered rocks in the district and surrounding region provide a means to ground truth the airborne data. We demonstrate that the airborne and ground-based measurements show similar map patterns. We calculate ratios of the radioelement concentrations and present a potassium enhancement map that combines potassium and ratios of potassium to thorium and uranium. The results highlight the rocks previously mapped as having K-feldspar-biotite and quartz-sericite alteration assemblages in the Elkhorn district and map additional hydrothermal systems in the region, including known alteration in the Radersburg district. The data enhancement techniques can be used as a screening tool for mapping additional porphyry copper systems.

Montana↗
USGS2025

Evolution of permeability and strength recovery of shear fracture under hydrothermal conditions

Geothermal energy is a clean and renewable resource that depends on the ability to move water through hot rock. In many locations, the ability to move water through rock requires the presence of extensive natural or human-made systems of fractures. However, these fracture systems are influenced by a variety of complex processes that occur at the temperature and pressure conditions found in geothermal reservoirs. To make geothermal systems more efficient, it is important to understand how these fractures evolve over time in response to these processes. This study explored how fractures in rock change under high-temperature and pressure conditions, like those found in geothermal reservoirs, through laboratory experiments and numerical simulations. In general fractures, tend to close due to pressure from the surrounding rock preventing the flow of water. One set of laboratory experiments revealed that fractures in granitic rock can weaken over time at elevated temperatures. These weak fractures can then slip slowly potentially keeping the fracture open for a longer period. This study also showed that at the highest temperature examined (250 °C) large differences between the chemical composition of the rock and the fluid moving through it could improve water flow temporarily likely due to the water dissolving parts of the rock. Flow rate predicted by models shows overall good agreement with the flow rate measured in our experiments but with some long time-scale variations that may be due to mechanical wear of the fracture surface. A second set of experiments found that, over the temperature range examined, the closure of fractures was caused by brittle failure driven by high stresses at points where fracture surfaces were in contact. This result suggests that fracture closure in geothermal reservoirs could be counteracted by maintaining high pore pressures. Additionally, we also tested a new method using electrical resistance to measure fracture closure in controlled systems with high precision.

Final Technical Report↗
USGS2025

Earthquake probabilities and hazards in the U.S. Pacific Northwest

Earthquakes and their cascading consequences pose a significant threat to the people, environment, infrastructure, and economy of the U.S. Pacific Northwest. The Pacific Northwest is susceptible to three types of earthquakes: deep (intraslab) earthquakes, subduction zone (megathrust) earthquakes, and shallow crustal earthquakes. For each of these earthquake types, earth scientists can use a variety of methods to estimate the probability of occurrence for future events, which constrains seismic hazard and informs building codes. The timing of past earthquakes indicates that there is an 85-percent chance of a magnitude 6.5 or greater deep earthquake in the Puget Sound region; a 10-15-percent chance of an approximately magnitude 9 earthquake on the Cascadia Subduction Zone; and a 17-percent chance of a magnitude 6.5 or greater crustal fault earthquake in the Puget Sound region in the next 50 years. Individuals and communities can take simple steps to prepare for and reduce the impact of future earthquakes.

California, Oregon, Washington↗
USGS2026

Origin of the Pd/Pt ratio of the J-M Reef, Stillwater Complex, Montana, USA

The J-M reef of the Stillwater Complex is characterized by a high Pd/Pt ratio (mean ~3.8 with a standard error of 0.03) with a homogeneous geospatial distribution at the deposit scale. In this contribution, we demonstrate that the Pd/Pt ratio of the reef is the product of equilibration of an immiscible sulfide liquid with a silicate melt rich in Pd relative to Pt. Despite the high tenors of the J-M reef sulfides (avg 2,700 ppm Pt and 770 ppm Pt), numerical modeling shows that the parental melts did not have extraordinary Pd and Pt concentrations. Instead, the initial composition of a plausible parental silicate melt can have Pd and Pt contents well within the expected range of a normal, mantle-derived partial melt (i.e., ~10–20 ppb for both Pd and Pt with Pd/Pt of ~1). The relative differences in the partitioning behavior of Pt and Pd between sulfide liquid and silicate melt are unlikely to produce a consistent Pd/Pt ratio across a wide range of silicate melt to sulfide liquid mass ratios (i.e., R factors). Instead, the pre-emplacement fractionation of Pt alloy from S-undersaturated silicate magma accounts for the homogeneous and high Pd/Pt ratio of the J-M reef. We show that batch equilibration of sulfide liquid with silicate melt can produce the high Pd/Pt ratios of the reef if the partition coefficients between sulfide liquid and silicate melt for Pd and Pt are extremely high (>10 6 ). In an alternative model, Pd enrichment could be achieved by sulfide upgrading in resident footwall mush even if the partition coefficients between sulfide liquid and silicate melt are relatively small (between 10 4 and 10 6 ) because the instantaneous mass ratio of silicate melt to sulfide liquid is small (R ≈ 100–700), so the partitioning behavior of Pt and Pd has little impact on the composition of sulfide liquid.

Montana↗
USGS1999

Streamflow, base flow, and ground-water recharge in the Housatonic River basin, western Massachusetts and parts of eastern New York and northwestern Connecticut

Streamflows for selected flow durations from 1 to 99 percent and the August median streamflows were estimated for 11 long-term streamflow-gaging stations in and near the study area. Estimates of streamflow and associated standard errors were determined for selected flow durations from 50 to 99 percent and the August median streamflows for 21 low-flow partial-record stations and for selected flow durations from 1 to 99 percent and the August median streamflows for two partial-record stations and seven short-term discontinued streamflow-gaging stations. Median streamflows per square mile for the 10-, 50-, and 90-percent flow durations and the August median streamflows were 3.90, 1.01, 0.185, and 0.248 cubic feet per second per square mile. Streamflows per square mile at selected flow-duration discharges between 1 and 99 percent at the 41 stations were related to basin characteristics to explain differences in streamflow characteristics. Basin characteristics included basin elevations, extent of stratified-drift deposits, land use, aspect, and underlying bedrock geology types. Most streamflow differences were positively correlated to basin elevation differences, most likely because precipitation increases with elevation, and to stratified-drift deposits, which allow more precipitation to recharge the ground water and to discharge later than do till and bedrock deposits. Mean base flow was computed from continuous records of daily mean discharge at 11 long-term streamflow-gaging stations in and near the study area. Mean annual base flow ranged from 13.4 to 24.5 inches per year. Minimum annual base flow ranged from 45 to 72 percent of mean annual rates at the 11 long-term stations, and the ratio of base flow to streamflow (base-flow index) ranged from 0.55 to 0.80. Base-flow durations between 1 and 99 percent were calculated from streamflow records at the 11 long-term streamflow-gaging stations. Base flow accounted for 45.5 to 85.0 percent of total annual streamflow at the 1- and 99-percent flow durations. Ground-water-recharge rates were computed from continuous records of daily mean discharge at 11 long-term streamflow-gaging stations in and near the study area. Mean annual ground-water-recharge rates ranged from 17.5 to 22.4 inches per year at 10 of the 11 long-term stations. Mean annual ground-water-recharge rates ranged from 2 to 7 inches per year higher than base flow. Minimum annual ground-water-recharge rates ranged from 48 to 72 percent of mean annual ground-water-recharge rates. Mean annual potential ground-water recharge was estimated from monthly climatological data collected at six climatological stations in and near the study area. Mean potential ground-water recharge ranged from about 17.9 to 28.9 inches per year, with a median value of 22.6 inches per year. This median value compares well to that calculated by use of streamflow records at the 11 streamflow-gaging stations (20.0 inches per year). Streamflows per square mile for the 10-, 50-, and 90-percent flow durations at stations in and near the study area were similar to those computed for other unregulated long-term continuous streamflow-gaging stations in central and eastern Massachusetts. Base-flow and ground-water-recharge rates in the study area compared closely to results from other studies in southeastern Massachusetts and Rhode Island, which were based on the same computational methods.

Connecticut, Massachusetts, New York↗
USGS2024

Isotopic evaluation of the National Water Model reveals missing agricultural irrigation contributions to streamflow across the western United States

The National Water Model (NWM) provides critical analyses and projections of streamflow that support water management decisions. However, the NWM performs poorly in lower-elevation rivers of the western United States (US). The accuracy of the NWM depends on the fidelity of the model inputs and the representation and calibration of model processes and water sources. To evaluate the NWM performance in the western US, we compared observations of river water isotope ratios ( 18 O / "> 16 O and 2 H / "> 1 H expressed in δ notation) to NWM-flux-estimated (model) river reach isotope ratios. The modeled estimates were calculated from long-term (2000–2019) mean summer (June, July, and August) NWM hydrologic fluxes and gridded isotope ratios using a mass balance approach. The observational dataset comprised 4503 in-stream water isotope observations in 877 reaches across 5 basins. A simple regression between observed and modeled isotope ratios explained 57.9 % ( δ 18 O) and 67.1 % ( δ 2 H) of variance, although observations were 0.5 ‰ ( δ 18 O) and 4.8 ‰ ( δ 2 H) higher, on average, than mass balance estimates. The unexplained variance suggest that the NWM does not include all relevant water fluxes to rivers. To infer possible missing water fluxes, we evaluated patterns in observation–model differences using δ 18 O diff ( δ 18 O obs − δ 18 O mod ) and d diff ( δ 2 H diff - 8 ⋅ δ 18 O diff "> ). We detected evidence of evaporation in observations but not model estimates (negative d diff and positive δ 18 O diff ) at lower-elevation, higher-stream-order, arid sites. The catchment actual-evaporation-to-precipitation ratio, the fraction of streamflow estimated to be derived from agricultural irrigation, and whether a site was reservoir-affected were all significant predictors of d diff in a linear mixed-effects model, with up to 15.2 % of variance explained by fixed effects. This finding is supported by seasonal patterns, groundwater levels, and isotope ratios, and it suggests the importance of including irrigation return flows to rivers, especially in lower-elevation, higher-stream-order, arid rivers of the western US.

Hydrology and Earth Systems Science↗
USGS2024

Temperature

The “National Field Manual for the Collection of Water-Quality Data” (NFM) provides guidelines and procedures for U.S. Geological Survey (USGS) personnel who collect data used to assess the quality of the Nation’s surface-water and groundwater resources. This chapter, NFM A6.1, provides guidance and protocols for the measurement of temperature of air, of a surface-water body or in groundwater, which include the scientific basis of the measurement, selection and maintenance of equipment, calibration verification, troubleshooting, and procedures for measurement and reporting. It updates and supersedes USGS Techniques of Water-Resources Investigations, book 9, chapter A6.1, version 2.0, by Franceska D. Wilde. Temperature of air and water is routinely measured when water samples are collected, is often measured continually at USGS streamgages, and is a parameter regularly measured during laboratory and field experiments. The field method for measuring temperature described in this chapter is applicable to air and most natural waters. Before 2017, the NFM chapters were released in the USGS Techniques of Water-Resources Investigations series. Effective in 2018, new and revised NFM chapters are being released in the USGS Techniques and Methods series; this series change does not affect the content and format of the NFM. More information is in the general introduction to the NFM (USGS Techniques and Methods, book 9, chapter A0) at https://doi.org/10.3133/tm9A0 . The authoritative current versions of NFM chapters are available in the USGS Publications Warehouse at https://pubs.usgs.gov/ . Comments, questions, and suggestions related to the NFM can be addressed to nfm@usgs.gov .

Techniques and Methods↗
USGS2024

Geological context and significance of the clay-sulfate transition region in Mount Sharp, Gale crater, Mars: An integrated assessment based on orbiter and rover data

On Mars, phyllosilicate (“clay”) minerals are often associated with older terrains, and sulfate minerals are associated with younger terrains, and this dichotomy is taken as evidence that Mars’ surface dried up over time. Therefore, in situ investigation of the Mount Sharp strata in Gale crater, which record a shift from dominantly clay-bearing to sulfate-bearing minerals, as seen in visible−near-infrared orbital reflectance spectra, is a key science objective for the Mars Science Laboratory (MSL) Curiosity rover mission. Here, we present regional (orbiter-based) and in situ (rover-based) evidence for a low-angle erosional unconformity that separates the lacustrine and marginal lacustrine deposits of the Carolyn Shoemaker formation from the dominantly eolian deposits of the lower Mirador formation within the orbitally defined clay-sulfate transition region. The up-section record of wetter (Carolyn Shoemaker formation) to drier (lower Mirador formation) depositional conditions is accompanied by distinct changes in diagenesis. Clay minerals occur preferentially within the Carolyn Shoemaker formation and are absent within the lower members of the Mirador formation. At and above the proposed unconformity, strata are characterized by an increase in diagenetic nodules enriched in X-ray amorphous Mg-sulfate. Early clay formation in the Carolyn Shoemaker formation may have created a hydraulic barrier such that later migrating magnesium- and sulfur-rich fluids accumulated preferentially within the lower members of the Mirador formation. The proposed unconformity may have also acted as a fluid conduit to further promote Mg-sulfate nodule formation at the Carolyn Shoemaker−Mirador formation boundary. These results confirm an association of the clay-sulfate transition with the drying of depositional environments, but they also suggest that at least some orbital sulfate signatures within the region are not time-congruent with the environmental signals extracted from primary sedimentology. Our findings highlight that complex interactions among primary depositional environment, erosion, and diagenesis contribute to the transition in clay-sulfate orbital signatures observed in the stratigraphy of Mount Sharp.

GSA Bulletin↗
USGS2025

Triple-oxygen isotopic evidence of prolonged direct bioleaching of pyrite with O2

Sulfate is often touted as containing atmospheric oxygen whose isotopic signature can constrain redox, environmental conditions, and biological activity. Yet, the amount and isotopic fractionation associated with air-O 2 incorporation during sulfate formation is still debated, making its verification difficult. In this study, we identify a distinct, microbially dominated environment with the potential to preserve maximum signals of air-O 2 in sulfate. We report triple-oxygen isotope data for sulfate produced from pyrite oxidation in microbial and abiotic experiments, and from natural dissolved sulfate from the Rio Tinto, Spain, an acid mine drainage site. The oxygen isotope systematics of sulfate in these environments define a unique kinetic isotope effect associated with initial stage pyrite oxidation by Acidithiobacillus ferrooxidans that preserves >80 % oxygen from air-O 2 in sulfate. Unlike experiments, which evolve toward water-oxygen dominated sulfate on short time scales, Rio Tinto, Spain hosts a microbe rich environment with distinct geochemistry that maintains high O 2 -oxygen in sulfate. Therefore, in addition to containing isotopic records from water and air, sulfates can also contain a biosignature that is promising for understanding conditions on Mars and early Earth.

Earth and Planetary Science Letters↗
USGS2024

Global geologic map of Europa

Discovered by Galileo Galilei more than 400 years ago and imaged in detail by the Voyager 2 Galileo spacecraft, Jupiter’s icy moon Europa has been a source of intrigue. A range of science investigations indicate that it contains the key ingredients for habitability, notably energy, chemistry, and liquid water. Europa’s surface is geologically complex and, based on the dearth of impact craters, interpreted to be as young as ~60 Ma. The array of geologic features that characterize the surface include extensive ridged plains, regions of broad disruption termed chaotic terrain, long, quasi-linear ridges that span thousands of kilometers, and bands as much as 60 kilometers wide and that extend 100s of kilometers. These features, along with other geophysical measurements, indicate the presence of a global briny liquid water ocean beneath the ice shell. It was not until the arrival of the Galileo spacecraft in 1995 that the true nature and level of complexity of the surface was revealed. Although image data returned by Galileo provided insight into the structure of a variety of regions, the entire satellite has yet to be observed at a regional scale (less than 250 meters per pixel) and the detailed geologic nature of much of its surface remains a mystery. Establishing the global context of the distribution and timing of Europan geologic units forms a basis to understand regional and local scale processes, serves as a tool for the planning of future missions, and most of all is essential to gaining insight into the potential habitability of this icy world.

Scientific Investigations Map↗
USGS2026

Hydrological control on soil redox condition and carbon loss of coastal wetland under sea-kevel rise

Coastal wetlands are critical carbon sinks with their biogeochemical and ecological functioning shaped by dynamic hydrological conditions that are increasingly influenced by climate change. A key unresolved question is how hydrologic flow, vegetation response, and rising sea levels interact to regulate soil redox condition and carbon loss in coastal wetlands. Using a field-tested hydrological–biogeochemical–ecological modeling framework, we reveal how the interplay between terrestrial groundwater discharge and tidal fluctuations generates complex groundwater flow patterns at the terrestrial–aquatic interface, and how these patterns modulate soil redox conditions, in turn influencing soil organic matter decomposition and carbon loss. Notably, rising sea levels suppress soil CO 2 emissions while reducing lateral dissolved carbon losses, thereby enhancing litter carbon sequestration under anoxic conditions. As vegetation responds to sea-level rise and carbon inputs diminish, litter carbon subsequently declines. These findings underscore a critical hydrological control on carbon cycling, advancing our understanding of coastal ecosystem resilience in a warming world.

Louisiana↗
USGS2024

Dissolved arsenic concentrations in surface waters within the upper portions of the Klamath River Basin, Oregon and California

Arsenic toxicity is an environmental health problem. Levels of arsenic in surface waters at some locations in the Klamath River Basin in southern Oregon and northern California can exceed the U.S. Environmental Protection Agency (EPA) standard for drinking water. There are both anthropogenic and natural sources of arsenic. The Klamath River Basin consists primarily of volcanic deposits and contains an underground geothermal system with hot springs and warm water wells, all known natural sources of arsenic. Anthropogenic sources of arsenic are related to the agricultural use of herbicides, fungicides, and insecticides. Surface water arsenic levels can also be affected by fertilizer amendments, evaporative concentration, oxygen-level depletion, and various geochemical transformations that can increase arsenic mobilization. In this study by the U.S. Geological Survey and the Bureau of Reclamation, dissolved concentrations of arsenic, copper, and lead were measured in surface waters at 39 unique sites within the upper portions of the Klamath River Basin between 2018 and 2022. In every year, except 2022, sites were sampled four times between April and November. Surface-water arsenic concentrations varied up to four-orders of magnitude among sites. Median arsenic concentration was lowest at Cherry Creek (0.03 micrograms per liter [μg/L]) and highest at Wood Kimball Spring (36.7 μg/L), two sites located north of Upper Klamath Lake. The highest arsenic concentrations (17.4±4.9 μg/L, n =3) were found in drain sites (defined here as a waterbody returning used irrigation water) while the lowest arsenic concentrations were found in an artesian well (0.8 μg/L, n =1). The elevated arsenic concentrations of the drain sites suggest that arsenic might be concentrated or mobilized by agricultural activities, water re-use practices, and (or) by geochemical processes occurring around water stored in drains (that is, in the water column and across sediment water boundaries). A source of arsenic in drain water in the Klamath Strait Drain area includes water used for irrigation originating from Ady Canal. Other potential sources include groundwater, geothermal water, and local soils and sediments. Seasonal differences in surface-water arsenic concentrations were detected at 13 sites, 10 of which had higher arsenic concentrations in summer than in either spring or fall. The sites sampled around Upper Klamath Lake, the impounded rivers, one of the two canal sites, and 5 of the 14 river sites had higher surface-water arsenic concentrations in the summer than in either spring or fall. Surface-water arsenic concentrations from groundwater sources (that is, springs and in the artesian well) did not vary significantly among seasons (p-values greater than 0.1). Median surface-water concentrations of copper and lead ranged from 0.03 to 3.7 μg/L, and from 0.013 to 0.175 μg/L ( n =2–18), respectively. Dissolved concentrations of both metals were below acute toxicity endpoints reported by the EPA for freshwater animals. Surface-water arsenic concentrations varied independently from corresponding changes in surface-water lead or copper concentrations. However, arsenic concentrations measured in bed-sediment samples collected from a subset of sites located north of Upper Klamath Lake correlated strongly and significantly with the corresponding sedimentary lead concentrations ( p =0.015). Aqueous arsenic speciation measured in a subset of sites in 2019 and 2022 showed that all the arsenic existed as arsenic (V), the most oxidized arsenic species, and presumably, the least toxic. The highest proportions of arsenite (As(III)), the presumably most toxic arsenic species, relative to total arsenic concentrations were found at drain sites. Our assessment of dissolved arsenic concentrations in various surface-water bodies in the Upper Klamath River Basin reveals geographical areas of consistently low (below 2.1 μg/L), moderate (below 10 μg/L) and high (above 10 μg/L) surface-water arsenic concentrations. South of Upper Klamath Lake, surface-water arsenic concentrations were consistently higher than 20 μg/L at two drain sites located in an area of predominant agricultural land use with extensive water re-use practices. North of Upper Klamath Lake, surface-water arsenic concentrations greater than 20 μg/L were consistently measured at sites with limited nearby agricultural activities, suggesting a geogenic source. The consistently high arsenic levels from the Wood River at Jackson F. Kimball State Park, Fort Creek, and Crooked Creek, which are sites located at or near headwater spring sources, suggest a natural background source of arsenic. Water flowing downstream from this area could be a potential source of arsenic to Upper Klamath Lake and the Upper Klamath River.

California, Oregon↗
USGS2024

Numerical model of the groundwater-flow system near the southeastern part of Puget Sound, Washington

Groundwater flow in the active model area (AMA) was simulated using a groundwater-flow model. A steady-state model version of the model simulates equilibrium conditions, and a transient model version simulates monthly variability. The model corresponds to the physical and temporal dimensions of the conceptual model and groundwater budget. The steady-state model version represents average conditions for an 11-year period (January 1, 2005–December 31, 2015), and the transient model represents monthly hydrologic variability within that period. The 13-layer model was constructed using MODFLOW-NWT with a uniformly spaced grid consisting of 416 rows, 433 columns, and cells with a horizontal dimension of 500 feet (ft) on a side. The model was calibrated to measured values of water levels in wells and lakes and estimated base flow for selected streamflow measurement stations, commonly referred to as streamgages. Model calibration was accomplished using a combination of manual and automatic methods, including the Model-Independent Parameter Estimation (PEST) program that adjusted model input parameters with the aim of minimizing the difference between estimated and model-simulated values of hydraulic head and base flow. Model boundary conditions consist of all simulated groundwater inflow to and outflow from the AMA. For example, a stream reach that simulates a gain from or loss to groundwater is a boundary condition that allows water to exit or enter, respectively, the groundwater system. Other boundary conditions include springs, seeps, precipitation recharge, groundwater exchange with lakes and Puget Sound, and groundwater pumping. A comparison of the estimated groundwater budget to that simulated by the steady-state model version indicates that the relative percentages of total inflow or total outflow for six major categories of boundary conditions are similar for the two budgets. The model was used to simulate three suites of scenarios of potential drought and water-use changes. Scenario 1 suite consisted of the steady-state model version that was run with 0, 15, 20, and 25 percent reduction of precipitation recharge to assess the corresponding reductions in base flow with decreasing recharge. The last simulation for the scenario 1 suite consisted of the transient model version simulating 3 years of consecutive seasonal drought, defined by the months of May through September, to assess the corresponding base-flow reductions. Scenario 2 suite consisted of the steady-state model version with all simulated groundwater use removed, compared with a simulation that includes current groundwater use to evaluate changes to potentiometric surfaces and base flows. Scenario 3 suite consisted of a transient model version of the model that simulated pumping increases for four different categories of water-supply wells (compared to no pumping increases) to evaluate resulting reductions in base flow. Although, these scenarios provide examples of model applications and useful insights, many other scenarios could be simulated. A description of how to download the model is described in the body of this report. Uncertainty is associated with most model inputs. Groundwater levels, lake levels, and land-surface altitudes are relatively certain; other model inputs are far less certain, including precipitation recharge, base flow, hydraulic properties, water use, and the three-dimensional structure of subsurface hydrogeologic units. Models are useful not because of high levels of accuracy of all model inputs, but because they combine the best information and estimates available, thereby providing the best predictions available related to physical processes. The model described in this report simulates groundwater flow on a regional scale, which has inherent limitations for simulating hydrologic scenarios at local scales. Model structures and inputs were generalized to be consistent with this regional scale. For example, the actual groundwater system has much greater heterogeneity of hydraulic conductivity than is possible within the model’s degrees of freedom. Variations in hydraulic gradients over distances less than 500 ft cannot be simulated. The distances between model features, such as a pumping well and a stream, must be placed at 500-ft intervals and are co-located if both features are within the same model cell.

Washington↗
USGS2025

A regional model comparison between MODPATH and MT3D of groundwater travel time distributions

Groundwater quality changes in wells and streams lag behind changes to land use due to groundwater travel times. Two contaminant transport methods were compared to assess differences in their simulated travel time distributions (TTDs) to streams and wells in the Wisconsin Central Sands. MODPATH simulates advective groundwater flow with particle tracking, while MT3D simulates age-mass using a finite difference solution without dispersion to allow for direct comparison of the two methods. MODPATH appropriately simulates groundwater TTDs from the water table to surface discharge but is subject to inaccuracies at weak-sink well cells due to the flow-model grid discretization and imprecise location of well discharge within well cells. MT3D better represents weak-sink well cells since it removes mass in proportion to the prescribed pumping rate, although travel time within well cells is neglected. Conversely, MT3D's treatment of surface water boundary cells is not as accurate as MODPATH because mass should be removed from the water table rather than the full cell volume. MT3D simulations of TTDs can also be confounded by the instantaneous vertical distribution of mass introduced throughout recharge cells instead of at the water table, which initiates mass along deeper flow paths. We evaluated 9 MODPATH and 13 MT3D implementations, generating differences in median travel times of up to 18 years. Both methods have strengths and weaknesses, with MT3D better representing weak-sink well cell behavior and MODPATH better representing surficial recharge and discharge. The effect of these characteristics on simulated TTDs, along with ideas for ameliorating method weaknesses, is discussed.

Wisconsin↗
USGS1997

Integrity of production wells and confining unit at the Naval Weapons Industrial Reserve Plant, Dallas, Texas, 1995

Ground water in the shallow alluvial aquifer is contaminated at the Naval Weapons Industrial Reserve Plant, Dallas, Texas. Five production wells at the site are cased through the alluvial aquifer and underlying units and are screened in either the Paluxy or Twin Mountains aquifers. Three abandoned wells, originally completed in the Twin Mountains aquifer but filled with drilling mud in 1958, also penetrate the alluvial aquifer. The Paluxy and Twin Mountains aquifers are used for drinking-water supplies in and around the Dallas-Fort Worth metroplex. Trichloroethylene and its degradation products, dichloroethylene and vinyl chloride, and the metal chromium previously have been detected in the shallow alluvial aquifer. Current (1995) analyses of water-quality samples taken from the static water column of the five production wells and one of the abandoned wells indicate no trichloroethylene, dichloroethylene, or vinyl chloride in the water column of these wells. Chromium was detected in all samples, but concentrations were less than the practical quantitation limit, which is the regulatory action level for this site. The results of borehole geophysical log analysis indicate that two of the production wells could have vertically connected intervals where cement bonding in the well annulus is poor. The other production wells have overall good bonding. Temperature logs do not indicate flow behind casing except in the screened interval of one well. Geophysical logs show the Eagle Ford Shale ranges from 147 to 185 feet thick at the site. The Eagle Ford Shale has low permeability and a high plasticity index. These physical characteristics make the Eagle Ford Shale an excellent confining unit.

Texas↗