USGS Science⌕ Search

SEARCH · USGS Science

Results for “Administrative Report.”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52Linked to original sources

Depth calibration of the Experimental Advanced Airborne Research Lidar, EAARL-B

Introduction The original National Aeronautics and Space Administration (NASA) Experimental Advanced Airborne Research Lidar (EAARL) was extensively modified to increase the spatial sampling density and to improve performance in water ranging from 3 to 44 meters (m). The new (EAARL-B) sensor features a higher spatial density that was achieved by optically splitting each laser pulse into three pulses spatially separated by 1.6 m along the flight track and 2.0 m across the flight track, on the water surface when flown at a nominal altitude of 300 m (984 feet). The sample spacing can be optionally increased to 1.0 m across the flight track. Improved depth capability was achieved by increasing the total peak laser power by a factor of 10 and by designing a new “deep-water” receiver, which is optimized to exclusively receive refracted and scattered light from deeper water (15–44 m). Two different clear-water flight missions were conducted over the U.S. Navy's South Florida Testing Facility (SFTF) to determine the EAARL-B calibration coefficients. The SFTF is an established lidar calibration range located in the coastal waters southeast of Fort Lauderdale, Florida. We used 23 selected polygons at 23 distinct depths to compare a reference dataset from this site to determine EAARL-B calibration constants over the depth range of 6.5 to 34 m. We also conducted a near-simultaneous single-beam jet-ski-based sonar survey of selected transects ranging from 1 to 33 m depth in the same area. The near-concurrent jet ski data were used to evaluate the EAARL-B performance over the depth range from 0.9 to 10 m. The more timely jet ski data were necessary because the primary reference dataset was 9 years old, and areas shallower than 6.5 m are dominated by shifting sand. We determined the jet ski data were not useful as a calibration reference in water deeper than 10 m due to large uncertainty in the vertical measurement introduced by the lack of any sensor orientation data, that is, for pitch, roll, and heading to correct the measured slant range to a vertical measurement. The resulting calibrated EAARL-B data were then analyzed and compared with the original reference dataset, the jet-ski-based dataset from the same Fort Lauderdale site, as well as the depth-accuracy requirements of the International Hydrographic Organization (IHO). We do not claim to meet all of the IHO requirements and standards. The IHO minimum depth-accuracy requirements were used as a reference only and we do not address the other IHO requirements such as “ Full Seafloor Search”. Our results show good agreement between the calibrated EAARL-B data and all reference datasets, with results that are within the 95 percent depth accuracy of the IHO Order 1 (a and b) depth-accuracy requirements.

Open-File Report↗

Gulf Islands National Seashore regional sediment budget research and data needs—Workshop series summary

Executive Summary The National Park Service (NPS), in collaboration with the U.S. Geological Survey (USGS), recognizes the need to quantify the sediment budget of the barrier islands within the Gulf Islands National Seashore (GINS) to understand the coastal processes affecting island resiliency. To achieve this goal, identifying and quantifying the physical parameters that drive long-term change is necessary to model the processes that are both generative and terminal in island evolution and capture island response to long-term human alteration and climatic patterns. For example, measuring change across periods of storminess is more effective at assessing island resiliency than measuring change resulting from a single storm impact. Understanding changes to the physical environment over time is key to successfully predicting island responses to future storm impacts, human alteration, and sea-level rise and is necessary for effective decision making and management response. Yet, the diversity of factors affecting natural and cultural resources necessitates a strategic approach to data collection priorities that can inform sediment budget quantification and integrated resource management. This study sought to advance sediment budget modeling efforts by conducting a “Needs Assessment Workshop” at the GINS. The purpose of the workshop was to identify and prioritize the specific research and data needs regarding the sediment budget at the GINS that can enhance the NPS efforts to conserve the islands’ natural resources, cultural resources, and the facilities and infrastructure that support both conservation and visitor use of those resources. This effort explored two research questions: (1) “what research and data needs exist for the sediment budget at Gulf Islands National Seashore” (research question 1) and (2) “how can research to address these needs capitalize on regional partnerships to advance natural and cultural resource conservation at Gulf Islands National Seashore” (research question 2)? The workshop was conducted virtually in a two-part, two-day series. The workshop series was organized by researchers from North Carolina State University in collaboration with NPS and USGS staff and was facilitated by National Oceanographic and Atmospheric Administration staff. The workshop series (two paired, sequential, partial-day workshops) addressed two target audiences: (1) NPS and USGS staff (April workshop) and (2) regional Federal, State, county, and nongovernmental organization staff, including NPS and USGS staff (May workshop). A total of four workshop sessions were held, comprising two sessions with each target audience. The workshop series intended to identify sediment management research and data needs that could enhance natural and cultural resource stewardship at the GINS. One objective was to share information about regional sediment transport and management, available sediment management plans, and predictive modeling capabilities, including geomorphologic and hydrodynamic predictive models. This information was shared through a series of presentations by park managers and NPS and USGS researchers that identified park issues and available capabilities and data. The second objective was to elicit research and data needs, with a primary goal of assessing the importance and urgency of the identified needs. This assessment was partly determined by requesting that the workshop participants identify and prioritize research themes through polls, comments, and discussion. The polls explicitly asked participants to qualitatively evaluate the importance (not at all, slightly, somewhat, very, or extremely) and urgency (not at all, slightly, somewhat, very, or extremely) of the thematically grouped research and data needs. These evaluations were plotted and shared during the workshop to visualize how the relative importance ( x -axis) and relative urgency ( y -axis) of each “need,” relative to other needs, to identify the most necessary (importance) and time-sensitive (urgent) items, thereby allowing an enhanced, holistic understanding of the sediment budget at GINS. Results of the poll are published as a USGS data release. The assessment results revealed that the most important and urgent research and data needs included mapping (for example, elevation, habitat, and cultural resources), a regional sediment budget and management plan, and the dynamic modeling of sediment processes. During the workshop, these issues were visualized using scatter plots to demonstrate the relative importance and urgency of each theme, provide descriptive statistics, and elicit discussion. This format of iterative presentation, discussion, and prioritization allowed the project team to effectively accomplish their objective of identifying important and urgent research needs for natural and cultural resource stewardship at the GINS. Through the workshop, it was determined that expanded communication with the broader research community was needed to coordinate research activities and streamline potential funding opportunities and that research and policy should be integrated through a structured decision-making process. At the conclusion of the workshop, an administered poll showed that the presentations effectively identified data and research needs and that the goals of the workshop were achieved. The results suggest that this type of needs-assessment workshop can effectively identify existing research capabilities and data, determine and prioritize research and data needs, and address how these efforts can use regional partnerships to aid natural and cultural resource conservation and management at National Parks.

Florida, Mississippi↗

Results of a workshop concerning assessment of the functions of bottomland hardwoods

The U.S. Environmental Protection Agency (EPA) is authorized under Section 404 of the Clean Water Act (33 U.S.C. 1344) to participate in the regulation of the discharge of dredged or fill material into waters of the United States. This regulatory authority is exercised in partnership with the U.S. Army Corps of Engineers, which has responsibility for permit issuance, and in consultation with the U.S. Fish and Wildlife Service and the National Marine Fisheries Service. Through amendments to the original statute, a series of legal actions and court decisions, and the development of operating guidance among the responsible agencies, Section 404 has evolved into the primary mechanism afforded Federal authorities for the protection of wetlands. EPA recognizes the importance of wetlands in achieving the goals of the Clean Water Act, which are to protect and maintain the chemical, physical, and biological integrity of the Nation’s waters. EPA Administrator Lee Thomas has identified wetlands protection as among the highest of Agency priorities. EPA recognizes that bottomland hardwood (BLH) wetlands have vital and unique attributes that, if lost, would severely impact the physical, chemical, and biological integrity of the Nation's waters. As part of a broad program to better protect the Nation's wetlands, EPA has therefore identified bottomland hardwood wetlands as a priority resource requiring special attention on a national basis. Recognizing the importance of implementing an effective, nationally consistent, and scientifically defensible regulatory program, EPA, in October 1984, issued Interim Operating Guidance to its field personnel for implementing the Section 404 regulatory program in bottomland hardwood wetlands. With the goal of improving and finalizing that guidance, EPA is sponsoring a series of workshops designed to answer key questions concerning BLH wetlands, based on the best scientific and technical information currently available. The first two workshops were directed toward summarizing existing scientific and technical knowledge concerning the functions of BLH ecosystems, the characteristics that are important to each function, and the impact of various development activities on those characteristics. The first workshop, which was held in St. Francisville, Louisiana, in December, 1984, examined a wetland zonation concept as a framework for gaining a greater understanding of BLH structure and function. The workshop set out to determine whether characterization of BLH resources as a series of relatively distinct zones, defined by concomitant variation in hydrologic regime, soils, and vegetation, might provide the basis for a useful and scientifically sound regulatory framework. For examp1e, if certain zones are of particular importance to one or more wetland functions that the Clean Water Act was intended to protect, then the zonation concept might be useful from the perspective of how various activities should be regulated. Discussions during the first workshop, however, indicated that the zonation concept provides, at best, only an incomplete picture of the structure and function of BLH ecosystems. In many cases, BLH functions are not limited to or closely correlated with particular zones and, furthermore, many factors other than zone are important determinants of BLH functions. With these responses in mind, the second workshop, held at Lake Lanier, Georgia, in July, 1985, was designed to elicit information on two questions. First, if zones are not an adequate framework for understanding the functions of BLH systems, what characteristics (predictors) can be used to assess the extent to which a particular site performs these functions? And second, what are the impacts of various development activities that often occur in BLH ecosystems on those characteristics and thus on the functions themselves? At the second workshop, individual workgroups dealing with particular subject areas (e.g., hydrology, water quality, fisheries, wildlife, ecosystem processes, and cultural/recreational/economic resources) were able to identify site characteristics that are important determinants of the performance of various functions. For example, the Hydrology Workgroup identified flood storage as one of three major hydrologic functions that BLH ecosystems perform. The workgroup then identified the most important characteristic (e.g., surface area of the site, soil saturation, and others) that determine flood storage and the likely impact of several common activities (e.g., conversion to soybean production and levee construction) on these characteristics. Some of the workgroups also provided estimates of the aggregate impact of activities, acting through all of the characteristics, on certain functions. The workgroups also identified key characteristics that could be used to identify high-value wetlands for various functions. In addition, the workgroups pointed out a number of topics needing further examination and discussion. First, all of the workgroups identified the need to develop the technical basis and information sources to address the problem of cumulative impacts in the regulatory process. Second, most of the workgroups noted the important of contextual variables in assessing the function of a particular site. For example, the location of a BLH site in relationship to other tracts of habitat is an important variable for many wildlife species. Similarly, the extent to which a site retains or transforms contaminants is depended not only on the characteristics of the site, but also on its position in a watershed relative to contaminant inputs. And finally, several of the workgroups pointed out that assessing the impact of an activity on a function is not as simple as "adding up" the impact on individual characteristics, but may depend instead on complex interactions among characteristics. Addressing these questions, as summarized in the objectives and discussions that follow, was the focus of the third workshop, the results of which are described in this report.

Report↗

Simulation of streamflow and water quality in the White Clay Creek subbasin of the Christina River Basin, Pennsylvania and Delaware, 1994-98

The Christina River Basin drains 565 square miles (mi 2 ) in Pennsylvania, Maryland, and Delaware. Water from the basin is used for recreation, drinking water supply, and to support aquatic life. The Christina River Basin includes the major subbasins of Brandywine Creek, White Clay Creek, and Red Clay Creek. The White Clay Creek is the second largest of the subbasins and drains an area of 108 mi 2 . Water quality in some parts of the Christina River Basin is impaired and does not support designated uses of the streams. A multi-agency water-quality management strategy included a modeling component to evaluate the effects of point and nonpoint-source contributions of nutrients and suspended sediment on stream water quality. To assist in non point-source evaluation, four independent models, one for each of the three major subbasins and for the Christina River, were developed and calibrated using the model code Hydrological Simulation Program—Fortran (HSPF). Water-quality data for model calibration were collected in each of the four main subbasins and in smaller subbasins predominantly covered by one land use following a nonpoint-source monitoring plan. Under this plan, stormflow and base- flow samples were collected during 1998 at two sites in the White Clay Creek subbasin and at nine sites in the other subbasins. The HSPF model for the White Clay Creek Basin simulates streamflow, suspended sediment, and the nutrients, nitrogen and phosphorus. In addition, the model simulates water temperature, dissolved oxygen, biochemical oxygen demand, and plankton as secondary objectives needed to support the sediment and nutrient simulations. For the model, the basin was subdivided into 17 reaches draining areas that ranged from 1.37 to 13 mi 2 . Ten different pervious land uses and two impervious land uses were selected for simulation. Land-use areas were determined from 1995 land-use data. The predominant land uses in the White Clay Creek Basin are agricultural, forested, residential, and urban. The hydrologic component of the model was run at an hourly time step and primarily calibrated using streamflow data from two U.S. Geological Survey (USGS) streamflow-measurement stations for the period of October 1, 1994, through October 29, 1998. Additional calibration was done using data from two other USGS streamflow-measurement stations with periods of record shorter than the calibration period. Daily precipitation data from two National Oceanic and Atmospheric Administration (NOAA) gages and hourly precipitation and other meteorological data for one NOAA gage were used for model input. The difference between simulated and observed streamflow volume ranged from -0.9 to 1.8 percent for the 4-year period at the two calibration sites with 4-year records. Annual differences between observed and simulated streamflow generally were greater than the overall error. For example, at a site near the bottom of the basin (drainage area of 89.1 mi 2 ), annual differences between observed and simulated streamflow ranged from -5.8 to 14.4 percent and the overall error for the 4-year period was -0.9 percent. Calibration errors for 36 storm periods at the two calibration sites for total volume, low-flowrecession rate, 50-percent lowest flows, 10-percent highest flows, and storm peaks were within the recommended criteria of 20 percent or less. Much of the error in simulating storm events on an hourly time step can be attributed to uncertainty in the hourly rainfall data. The water-quality component of the model was calibrated using data collected by the USGS and state agencies at three USGS streamflow-measurement stations with variable water-quality monitoring periods ending October 1998. Because of availability, monitoring data for suspended-solids concentrations were used as surrogates for suspended-sediment concentrations, although suspended solids may underestimate suspended sediment and affect apparent accuracy of the suspended-sediment simulation. Comparison of observed to simulated loads for up to five storms in 1998 at each of the two nonpoint-source monitoring sites in the White Clay Creek Basin indicate that simulation error is commonly as large as an order of magnitude for suspended sediment and nutrients. The simulation error tends to be smaller for dissolved nutrients than for particulate nutrients. Errors of 40 percent or less for monthly or annual values indicate a fair to good water-quality calibration according to recommended criteria, with much larger errors possible for individual events. The accuracy of the water-quality calibration under stormflow conditions is limited by the relatively small amount of water-quality data available for the White Clay Creek Basin. Users of the White Clay Creek HSPF model should be aware of model limitations and consider the following if the model is used for predictive purposes: streamflow and water quality for individual storm events may not be well simulated, but the model performance is reasonable when evaluated over longer periods of time; the observed flow-duration curve for the simulation period is similar to the long-term flow-duration curve at White Clay Creek near Newark, Del., indicating that the calibration period is representative of all but highest 0.1 percent and lowest 0.1 percent of flows at that site; relative errors in streamflow and water-quality simulations are greater for smaller drainage areas than for larger areas; and calibration for water-quality was based on sparse data.

Water-Resources Investigations Report↗

Vessel surveys for marine birds in the Gulf of America (Gulf of Mexico): Protocol manual (2017–2025)

This manual provides contextual background and detailed instructions for survey procedures that were used to collect, enter, archive, and analyze digitally-entered field data collected for marine birds during three large-vessel survey projects in the northern Gulf of America (also Gulf of Mexico, hereafter “Gulf”). Projects using this protocol included the Gulf of Mexico Marine Assessment Program for Protected Species (GoMMAPPS: 2017-2018), the Vessel Surveys for Abundance and Distribution of Marine Mammals and Seabirds (VSAD: 2023-2024), and certain repositioning legs of the Atlantic Marine Assessment Program for Protected Species (AMAPPS: 2021, 2023). Based substantially on Ballance and Force (2011), the protocol used in the Gulf is based on a standardized 300 m wide strip transect using software architecture available in program SeeBird (v.4.3.7), a data collection program developed by Robert Holland at the National Oceanic and Atmospheric Administration (NOAA) Southwest Fisheries Science Center, La Jolla, CA. Survey protocols relied on the digital entering of standardized metadata linked to sightings of seabirds (e.g., species, number, location, distance bin, association[s], behavior, flight direction, flight height, angle from ship, age, sex, plumage, and optional comments) as well as other protected species. SeeBird has additional modules that may be used to input data on mixed-species seabird flocks and flying fish (only the latter was used in the Gulf). SeeBird includes “user-driven” commands issued through the keyboard, touch screen, and/or mouse, many of which are aided by drop-down menus that prompt the user options that are available for input. In addition, the program features “event–driven” inputs updated at intervals selected by the user, and that also record exact time and location of such edits. We describe how SeeBird was adapted in the Gulf both to run directly via serial connections from the ship’s navigation system and to operate independently from the ship through a satellite-derived GPS feed. This user manual also gives information about: procedures used to document flying fish abundance on Gulf surveys; how to use the Beaufort scale for standardizing wind force and sea state environmental conditions; how to make and use a hand-held rangefinder for delimiting strip transect bin distances; additional functionalities in SeeBird for which user guides are not available; file-naming, file-archiving, and file location conventions used on Gulf marine bird surveys; protocols used in the Gulf for describing relative abundance of the macro-alga Sargassum as an environmental covariate; the standardized four-letter taxa codes (summarized in a SpeciesCode.txt file) used in the Gulf for denoting species, other taxonomic, and event categories as inputs to SeeBird; an Excel example spreadsheet that has successfully imported SeeBird’s ASCII text file; procedural steps to import, edit, and archive into Excel ASCII text files from SeeBird; initialization instructions for starting up program SeeBird on a Panasonic ToughBook™ that relies on integrated, satellite-derived GPS, and for writing “S” (seabirds + other taxa) and “E” (flying fish) ASCII files to a folder or subfolder other than the default root location on the laptop that contains program SeeBird; how to trouble-shoot miscellaneous start-up problems with program SeeBird; how to add new four-letter codes (into a SpeciesCode.txt file) when additional taxa or objects of interest are encountered. The primary objective of this manual is to archive a permanent, replicable history of survey methodology to facilitate continuity with comparable future projects that may be conducted in the Gulf. A secondary objective is to describe why and how program SeeBird was applied and adapted specifically for operating in Gulf survey conditions. As of late 2025, user guides for software program SeeBird were no longer readily accessible, so this manual serves also to address that gap.

Northern Gulf of America↗

Simulation of streamflow and water quality in the Red Clay Creek subbasin of the Christina River Basin, Pennsylvania and Delaware, 1994-98

The Christina River Basin drains 565 square miles (mi 2 ) in Pennsylvania and Delaware and includes the major subbasins of Red Clay Creek, White Clay Creek, Brandywine Creek, and Christina River. The Red Clay Creek is the smallest of the subbasins and drains an area of 54 mi 2 . Streams in the Christina River Basin are used for recreation, drinking-water supply, and to support aquatic life. Water quality in some parts of the Christina River Basin is impaired and does not support designated uses of the stream. A multi-agency, waterquality management strategy included a modeling component to evaluate the effects of point and nonpointsource contributions of nutrients and suspended sediment on stream water quality. To assist in nonpointsource evaluation, four independent models, one for each of the four main subbasins of the Christina River Basin, were developed and calibrated using the model code Hydrological Simulation Program?Fortran (HSPF). Water-quality data for model calibration were collected in each of the four main subbasins and in smaller subbasins predominantly covered by one land use following a nonpoint-source monitoring plan. Under this plan, stormflow and base-flow samples were collected during 1998 at 1 site in the Red Clay Creek subbasin and at 10 sites elsewhere in the Christina River Basin. The HSPF model for the Red Clay Creek subbasin simulates streamflow, suspended sediment, and the nutrients, nitrogen and phosphorus. In addition, the model simulates water temperature, dissolved oxygen, biochemical oxygen demand, and plankton as secondary objectives needed to support the sediment and nutrient simulations. For the model, the basin was subdivided into nine reaches draining areas that ranged from 1.7 to 10 mi 2 . One of the reaches contains a regulated reservoir. Ten different pervious land uses and two impervious land uses were selected for simulation. Land-use areas were determined from 1995 land-use data. The predominant land uses in the Red Clay Creek subbasin are agricultural, forested, residential, and urban. The hydrologic component of the model was run at an hourly time step and calibrated using streamflow data from three U.S. Geological Survey (USGS) streamflow-measurement stations for the period of October 1, 1994, through October 29, 1998. Daily precipitation data from one National Oceanic and Atmospheric Administration (NOAA) gage and hourly data from one NOAA gage were used for model input. The difference between observed and simulated stream- flow volume ranged from -0.8 to 2.1 percent for the 4-year period at the three calibration sites. Annual differences between observed and simulated streamflow generally were greater than the overall error for the 4-year period. For example, at a site near Stanton, Del., near the bottom of the basin (drainage area of 50.2 mi 2 ), annual differences between observed and simulated streamflow ranged from -5.8 to 6.0 percent and the overall error for the 4-year period was -0.8 percent. Calibration errors for 36 storm periods at the three calibration sites for total volume, low-flow-recession rate, 50-percent lowest flows, 10-percent highest flows, and storm peaks were 20 percent or less. Much of the error in simulating storm events on an hourly time step can be attributed to uncertainty in the rainfall data. The water-quality component of the model was calibrated using nonpoint-source monitoring data collected in 1998 at one USGS streamflowmeasurement station and other water-quality monitoring data collected at three USGS streamflowmeasurement stations. The period of record for waterquality monitoring was variable at the stations, with an end date of October 1998 but the start date ranging from October 1994 to January 1998. Because of availability, monitoring data for suspended-solids concentrations were used as surrogates for suspendedsediment concentrations, although suspended solids may underestimate suspended sediment and affect apparent accuracy of the suspended-sediment simulation. Comparison of observed to simulated loads for five storms in 1998 at the one nonpoint-source monitoring site at Wooddale, Del., indicates that simulation error commonly is as large as an order of magnitude for suspended sediment and nutrients. The simulation error tends to be smaller for dissolved utrients than particulate nutrients. Errors of 40 percent or less for monthly or annual values indicate a fair to good water-quality calibration according to recommended criteria, with much larger errors possible for individual storm events. Assessment of the accuracy of the water-quality calibration under stormflow conditions is limited by the sparsity of available water-quality data in the basin. Users of the Red Clay Creek HSPF model should be aware of model limitations and consider the following when predictive scenarios are desired: streamflow-duration curves indicate the model simulates stream-flow reasonably well when evaluated over a broad range of conditions and time, although streamflow and the corresponding water quality for individual storm events may not be well simulated; streamflow-duration curves for the simulation period compare well with duration curves for the 57.5-year period ending in 2001 at Wooddale, Del., and include all but the extreme high-flow and low-flow events; calibration for water quality was based on sparse data, with the result of increasing uncertainty in the water-quality simulation.

Water-Resources Investigations Report↗

Hydrologic, Water-Quality, and Meteorological Data for the Cambridge, Massachusetts, Drinking-Water Source Area, Water Year 2005

Records of water quantity, water quality, and meteorological parameters were continuously collected from three reservoirs, two primary streams, and four subbasin tributaries in the Cambridge, Massachusetts, drinking-water source area during water year 2005 (October 2004 through September 2005). Water samples were collected during base-flow conditions and storms in the subbasins of the Cambridge Reservoir and Stony Brook Reservoir drainage areas and analyzed for selected elements, organic constituents, suspended sediment, and Escherichia coli bacteria. These data were collected to assist watershed administrators in managing the drinking-water source area and to identify potential sources of contaminants and trends in contaminant loading to the water supply. Monthly reservoir capacities for the Cambridge Reservoir varied from about 59 to 98 percent during water year 2005, while monthly reservoir capacities for the Stony Brook Reservoir and the Fresh Pond Reservoir were maintained at capacities greater than 84 and 96 percent, respectively. Assuming a water demand of 15 million gallons per day by the city of Cambridge, the volume of water released from the Stony Brook Reservoir to the Charles River during the 2005 water year is equivalent to an annual water surplus of about 119 percent. Recorded precipitation in the source area for the 2005 water year was within 2 inches of the total annual precipitation for the previous 2 water years. The monthly mean specific conductances for the outflow of the Cambridge Reservoir were similar to historical monthly mean values. However, monthly mean specific conductances for Stony Brook near Route 20, in Waltham (U.S. Geological Survey station 01104460), which is the principal tributary feeding the Stony Brook Reservoir, were generally higher than the medians of the monthly mean specific conductances for the period of record. Similarly, monthly mean specific conductances for a small tributary to Stony Brook (U.S. Geological Survey station 01104455) were generally higher than the medians of the monthly mean specific conductances for the period of record. The annual mean specific conductance for Fresh Pond Reservoir increased from 514 microsiemens per centimeter (?S/cm) in the 2004 water year to 553 ?S/cm for the 2005 water year. Water samples were collected from four tributaries during base-flow and stormflow conditions in December 2004, and July, August, and September 2005 and analyzed for suspended sediment, 6 major dissolved ions, total nitrogen, total phosphorus, 8 total metals, 18 polyaromatic hydrocarbons (PAHs), 61 pesticides and metabolites, and Escherichia coli bacteria. Concentrations for most dissolved constituents in samples of stormwater were generally lower than the concentrations observed in samples collected during base flow; however, concentrations of total phosphorus, PAHs, suspended sediment, and some total recoverable metals were substantially greater in stormwater samples. Concentrations of dissolved chloride and total recoverable manganese in water samples collected during base-flow conditions from three tributaries exceeded the U.S. Environmental Protection Agency (USEPA) secondary drinking water standards of 250 and 0.05 milligrams per liter (mg/L), respectively. Concentrations of total recoverable manganese exceeded the secondary drinking water standard in samples of stormwater from each tributary. Concentrations of total recoverable iron in water samples exceeded the (USEPA) secondary drinking water standard of 0.3 mg/L periodically in water samples collected at (USEPA) stations 01104415, 01104455, and 01104475, and consistently in all water samples collected at USGS station 01104433. Concentrations of Escherichia coli bacteria in water samples collected during base flow ranged from 4 to 1,400 colony-forming units per 100 milliliters (col/100mL). Concentrations of Escherichia coli bacteria in composite samples of stormwater ranged between 1,700 to 43,000 c

Open-File Report↗

EAARL coastal topography - Northern Gulf of Mexico

These remotely sensed, geographically referenced elevation measurements of Lidar-derived coastal topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. One objective of this research is to create techniques to survey areas for the purposes of geomorphic change studies following major storm events. The USGS Coastal and Marine Geology Program's National Assessment of Coastal Change Hazards project is a multi-year undertaking to identify and quantify the vulnerability of U.S. shorelines to coastal change hazards such as effects of severe storms, sea-level rise, and shoreline erosion and retreat. Airborne Lidar surveys conducted during periods of calm weather are compared to surveys collected following extreme storms in order to quantify the resulting coastal change. Other applications of high-resolution topography include habitat mapping, ecological monitoring, volumetric change detection, and event assessment. The purpose of this project is to provide highly detailed and accurate datasets of the northern Gulf of Mexico coastal areas, acquired on September 19, 2004, immediately following Hurricane Ivan. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Airborne Advanced Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532 nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking RGB (red-green-blue) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers and an integrated miniature digital inertial measurement unit which provide for sub-meter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system on September 19, 2004. The survey resulted in the acquisition of 3.2 gigabytes of data. The data were processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for pre-survey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that represent submerged or sub-aerial topography. Specialized filtering algorithms have been implemented to determine the 'bare earth' under vegetation from a point cloud of 'last return' elevations.

Alabama, Florida, Mississippi↗

Guidelines for use of fishes in research

The 2004 and 2014 Guidelines were developed to provide a structure that advances appropriate attention toward valid experimental designs and procedures with aquatic animals while ensuring humane treatment of the experimental subjects. At a practical level, the Guidelines are intended to provide general recommendations on field and laboratory endeavors, such as sampling, holding, and handling fishes; to offer information on administrative matters, including regulations and permits; and to address typical ethical concerns, such as perceptions of pain or discomfort experienced by experimental subjects. These Guidelines must be recognized as guidelines . They are not intended to provide detailed instructions but rather to alert investigators to a broad array of topics and concerns to consider prior to initiating study. At a comprehensive level, the principles upon which these Guidelines are based are broadly applicable, and many of the described practices and approaches can be adapted to situations involving other aquatic animal species and conditions. Understanding the differences between fishes and other vertebrates, especially mammals, is critically important to conducting scientifically sound research with fishes. Disparities in life histories and mortality rates in fishes versus other vertebrates are critical in designing sustainable sampling levels in fish populations. The UFR Committee points out that (1) compared to mammalian populations, adult populations of many fish species persist despite very high natural mortality rates in juvenile stages by virtue of the fact that most species lay thousands or tens of thousands of eggs; (2) because of these mortality patterns, research on fishes, especially field research or research on early life stages, can involve, and often requires, much larger numbers of research subjects than does research on mammals; and (3) the animal handling and husbandry requirements for fishes are fundamentally different from those for mammals and other vertebrates, in general. Policies, regulations, and recommendations developed for research on mammals, birds, reptiles, or even amphibians are frequently inappropriate for research with fishes. The Guidelines also address some of the ethical concerns that motivate guidelines used for research with other vertebrates, while being mindful of the unique physiology and general nature of fishes. The Guidelines were developed for general use by investigators within the United States; therefore, the roles, responsibilities, and informational needs of Institutional Animal Care and Use Committees (IACUCs) were given specific attention. All United States institutions that use vertebrate animals for research, teaching, research training, and biological testing are required to create an IACUC to oversee and evaluate all aspects of the institution’s animal care and use program. Investigators from other nations who read this document may disregard specific references to U.S. state and federal laws and regulations, as their institutional infrastructure and processes may differ from those of an internal committee such as IACUCs. The principles described herein, however, are applicable to research on fishes regardless of geographic location. Investigators in other nations may benefit by modifying any of the specific provisions pertaining to the United States, thereby adopting guidelines consistent with the laws and regulations of their own government. The UFR Committee urges that the Guidelines be endorsed and adopted (adapted, where necessary) by those state and federal authorities with regulatory responsibilities for fishes, offices with federal oversight (e.g., National Institutes of Health, Office of Laboratory Animal Welfare; http://grants.nih.gov/grants/olaw/olaw.htm ) as well as by universities and other institutions and authorities using fishes and aquatic animals within their research and teaching programs.

Report↗

Electrical Resistivity and Seismic Surveys at the Nevada Test Site, Nevada, April 2007

In April 2007, the USGS collected direct-current (DC) electrical resistivity data and shear- (S) and compressional- (P) wave seismic data to provide new detail of previously mapped, overlapping fault splays at two administrative areas in the Nevada Test Site (NTS). In NTS Area 7, we collected two-dimensional DC resistivity data along a transect crossing the Yucca Fault parallel to, and between, two transects along which resistivity data were collected in a previous study in 2006. In addition, we collected three-dimensional DC resistivity data in a grid that overlies part of the 2007 transect. The DC resistivity data show that the fault has a footwall that is more conductive than the hanging wall and an along-strike progression of the fault in a location where overlapping splays are present. Co-located with the northernmost of the two 2006 DC resistivity transects, we acquired S- and P-wave seismic data for both reflection and refraction processing. The S-wave data are corrupted by large amounts of converted (P-wave) energy likely due to the abundance of fractured caliche in the shallow subsurface. The P-wave data show minimal reflected energy, but they show clear refracted first arrivals. We have inverted these first arrival times to determine P-wave seismic velocity models. The seismic model for the transect in Area 7 shows low velocities extending to the base of the model at the location of the Yucca Fault, as well as low velocities at the eastern end of the transect, in the vicinity of the adjacent crater. These new surveys provide further detail about the geometry of the Yucca Fault in this location where it shows two overlapping splays. We collected P- and S-wave seismic data along a transect in the southern part of NTS Area 2, corresponding with the location of a 2006 DC resistivity transect that targeted a set of small faults identified with field mapping. Again, the S-wave data are difficult to interpret. The P-wave data show clear first arrivals that we inverted, yielding a velocity model that shows lateral heterogeneity similar to the 2006 DC resistivity models. Finally, we collected P-wave data along a second transect in Area 2, located north of the first line and in an area of a very minor fault that was targeted by another 2006 DC resistivity survey. The P-wave refraction velocity model shows generally high velocities, with a zone of somewhat lower velocities in the central part of the transect. The position of the low velocity zone corresponds with the location of a minor fault, though it is unclear whether the two are related. Together, these results demonstrate the value of geophysical data for mapping the subsurface extent of faults. The 2007 DC resistivity data complement the 2006 data and provide important new detail of the overlapping fault splays. The seismic data demonstrate the ability of P-wave refraction methods to identify the damage zones at faults, and they show the difficulties associated with S-wave methods in areas with caliche. Combining all of the geophysical data from the Area 7 studies, we are able to develop a coherent interpretation of the relation between the site geology, the fault, and the observations.

Open-File Report↗

Surface-water, water-quality, and meteorological data for the Cambridge, Massachusetts, drinking-water source area, water years 2007-08

Records of water quantity, water quality, and meteorological parameters were continuously collected from three reservoirs, two primary streams, and five subbasin tributaries in the Cambridge, Massachusetts, drinking-water source area during water years 2007-08 (October 2006 through September 2008). Water samples were collected during base-flow conditions and storms in the Cambridge Reservoir and Stony Brook Reservoir drainage areas and analyzed for dissolved calcium, sodium, chloride, and sulfate; total nitrogen and phosphorus; and polar pesticides and metabolites. Composite samples of stormwater also were analyzed for concentrations of total petroleum hydrocarbons and suspended sediment in one subbasin in the Stony Brook Reservoir drainage basin. These data were collected to assist watershed administrators in managing the drinking-water source area and to identify potential sources of contaminants and trends in contaminant loading to the water supply. Monthly reservoir contents for the Cambridge Reservoir ranged from about 30 to 95 percent of capacity during water years 2007-08. Monthly reservoir contents for the Stony Brook Reservoir ranged from about 47 to 91 percent of capacity during water years 2007-08, while the monthly reservoir storage values for Fresh Pond Reservoir were maintained at greater than 92 percent of capacity. If the average water demand by the city of Cambridge is assumed to be 15 million gallons per day, the volume of water released from the Stony Brook Reservoir to the Charles River during water years 2007-08 represents an annual surplus of about 107 and 94 percent, respectively. The annual precipitation total of about 47 in (inches) recorded at the Cambridge reservoir during water year 2007 was about 5 to 21 percent lower than recorded totals for the previous four water years, whereas the annual precipitation total of about 62 in. during water year 2008 was about 5 to 32 percent higher than recorded totals for water years 2002-07. In general, most monthly mean specific-conductance values for water year 2007 for U.S. Geological Survey (USGS) stations on the two primary streams and four subbasin tributaries in the Cambridge, Massachusetts, drinking-water source area were below the previous median monthly values and often were below the previous minimum monthly values for available data since water year 1997. The annual mean specific-conductance value for Fresh Pond Reservoir during water year 2007 was 483 (u or mu)S/cm (microsiemens per centimeter), which was lower than the prior three water years. The monthly mean specific-conductance values for streamflow for Hobbs Brook below the Cambridge Reservoir for December through July 2008 were greater than the 75th percentile for historical data since water year 1997. These relatively high values were caused by the inflow of high specific conductance water from the tributaries when the reservoir water level was low at the onset of winter. Increased rainfall in the watershed beginning in February 2008 caused monthly mean specific-conductance values for Hobbs Brook to decrease to about 700 (u or mu)S/cm by the end of the water year. Monthly mean specific-conductance values for many of the other USGS stations were higher than historical values for several months during the winter of water year 2008. The large amount of rainfall in the watershed also caused the monthly mean specific conductance at these stations to decline to near-median values or to values within the interquartile range for available historical data. The annual mean specific conductance for Fresh Pond Reservoir during water year 2008 was 497 (u or mu)S/cm, slightly greater than the corresponding value for the prior year. Water samples were collected in nearly all of the subbasins in the Cambridge drinking-water source area and from Fresh Pond during the study period. Discrete water samples were collected during base-flow conditions with an antecedent dry period of at least 3 days. Composite sampl

Cambridge, Massachusetts↗

Hydrologic, Water-Quality, and Meteorological Data for the Cambridge, Massachusetts, Drinking-Water Source Area, Water Year 2006

Records of water quantity, water quality, and meteorological parameters were continuously collected from three reservoirs, two primary streams, and four subbasin tributaries in the Cambridge, Massachusetts, drinking-water source area during water year 2006 (October 2005 through September 2006). Water samples were collected during base-flow conditions and storms in the subbasins of the Cambridge Reservoir and Stony Brook Reservoir drainage areas and analyzed for dissolved calcium, sodium, chloride, and sulfate; total nitrogen and phosphorus; and polar pesticides and metabolites. These data were collected to assist watershed administrators in managing the drinking-water source area and to identify potential sources of contaminants and trends in contaminant loading to the water supply. Monthly reservoir contents for the Cambridge Reservoir varied from about 59 to 98 percent of capacity during water year 2006, while monthly reservoir contents for the Stony Brook Reservoir and the Fresh Pond Reservoir was maintained at greater than 83 and 94 percent of capacity, respectively. If water demand is assumed to be 15 million gallons per day by the city of Cambridge, the volume of water released from the Stony Brook Reservoir to the Charles River during the 2006 water year is equivalent to an annual water surplus of about 127 percent. Recorded precipitation in the source area was about 16 percent greater for the 2006 water year than for the previous water year and was between 12 and 73 percent greater than for any recorded amount since water year 2002. The monthly mean specific-conductance values for all continuously monitored stations within the drinking-water source area were generally within the range of historical data collected since water year 1997, and in many cases were less than the historical medians. The annual mean specific conductance of 738 uS/cm (microsiemens per centimeter) for water discharged from the Cambridge Reservoir was nearly identical to the annual mean specific conductance for water year 2005 which was 737 uS/cm. However, the annual mean specific conductance at Stony Brook near Route 20 in Waltham (U.S. Geological Survey (USGS) station 01104460), on the principal tributary to the Stony Brook Reservoir, and at USGS station 01104475 on a smaller tributary to the Stony Brook Reservoir were about 15 and 13 percent lower, respectively, than the previous annual mean specific conductances of 538 and 284 uS/cm, respectively for water year 2005. The annual mean specific conductance for Fresh Pond Reservoir decreased from 553 uS/cm in the 2005 water year to 514 uS/cm in the 2006 water year. Water samples were collected in nearly all of the subbasins in the Cambridge drinking-water source area and from Fresh Pond during water year 2006. Discrete water samples were collected during base-flow conditions with an antecedent dry period of at least 4 days. Composite samples, consisting of as many as 100 subsamples, were collected by automatic samplers during storms. Concentrations of most dissolved constituents were generally lower in samples of stormwater than in samples collected during base flow; however, the average concentration of total phosphorus in samples of stormwater were from 160 to 1,109 percent greater than the average concentration in water samples collected during base-flow conditions. Concentrations of total nitrogen in water samples collected during base-flow conditions and composite samples of stormwater at USGS stations 01104415, 01104460, and 01104475 were similar, but mean concentrations of total nitrogen in samples of stormwater differed by about 0.5 mg/L (milligrams per liter) from those in water samples collected during base-flow conditions at U.S. Geological Survey stations 01104433 and 01104455. In six water samples, measurements of pH were lower than the U.S. Environmental Protection Agency (USEPA) national recommended freshwater quality criteria and the USEPA secondary drinking water-standa

Open-File Report↗

Summary of the history and research of the U.S. Geological Survey gas hydrate properties laboratory in Menlo Park, California, active from 1993 to 2022

The U.S. Geological Survey (USGS) Clathrate Hydrate Properties Project, active from 1993 to 2022 in Menlo Park, California, stemmed from an earlier project on the properties of planetary ices supported by the National Aeronautics and Space Administration’s (NASA’s) Planetary Geology and Geophysics Program. We took a material science approach in both projects, emphasizing chemical purity of samples, having controlled grain size and grain texture, and having verified crystal structures and phase relations. A foundational contribution from our USGS Gas Hydrate Properties Laboratory (GHPL) was in demonstrating the ability to reproducibly create such pure clathrate hydrate samples for study. Clathrate sample synthesis was achieved by heating sieved and weighed pure granular water ice in the presence of cold clathrate-forming gas or liquid. During heating, the ice melts at the grain scale and reacts with the gas to form clathrate. The resulting material has the desired uniformity and purity, with known intergranular porosity; our subsequent measurements showed that these clathrates exhibited the established clathrate structures and phase relations. This novel synthesis method was successful in creating clathrates of pure methane, ethane, propane, carbon dioxide, and multi-component gases. By mixing sand or silt with granular ice, we were also able to make clathrate-sediment aggregates with controlled grain textures. This simple method, adopted by many others in the community, permitted us to measure the physical and chemical properties of well-characterized and well-crystallized clathrates and clathrate/sediment aggregates. At about the same time, we adapted conventional scanning electron microscopy to cryogenic conditions for analysis of grain-scale characteristics of clathrates made in the GHPL as well as those collected from nature by drill core. The uniformity and reproducibility of our samples also allowed us to investigate how clathrates respond to environmental changes in chemistry, temperature, and pressure: we measured chemical exchange rates with dissolved gas species—such as noble gases and chlorofluorocarbons—as well as rates of clathrate dissolution and decomposition. These advances include the first accurate mapping of the conditions that promote the remarkable process of “anomalous preservation” at room pressure, a metastability that offers potential application for low-cost and safe transportation of natural gas from gas fields far from pipelines. Another advancement stemming from the GHPL was the compaction of as-synthesized porous clathrates to nearly full density by applying external pressure using three different techniques. Compaction allows for high-accuracy measurements of many fundamental physical and chemical properties of these materials, such as elastic wavespeeds and moduli, complete thermal properties, decomposition rates, thermal expansion, and clathrate equations of state. These properties and others, in turn, have helped USGS scientists to interpret geophysical well logs and active geophysical surveys, as well as model the rates of gas production from hydrate deposits in nature. Studying this class of icy minerals that occur in abundance on Earth and in the outer solar system has been a fascinating laboratory journey. Here, we summarize the history and major findings of the USGS GHPL in Menlo Park, including both in-house research as well as findings from the synergistic collaborations with other agencies and institutes that were key to the success of our laboratory. The Menlo Park GHPL was more formally incorporated within the USGS Gas Hydrates Project, a collaboration among multiple USGS Science Centers, in the early 2000s under the leadership of Deborah Hutchinson, and now under the leadership of Carolyn Ruppel and Timothy Collett.

Open-File Report↗

Simulation of streamflow and water quality in the Christina River subbasin and overview of simulations in other subbasins of the Christina River Basin, Pennsylvania, Maryland, and Delaware, 1994-98

The Christina River Basin drains 565 square miles (mi 2 ) in Pennsylvania and Delaware and includes the major subbasins of Brandywine Creek, Red Clay Creek, White Clay Creek, and Christina River. The Christina River subbasin (exclusive of the Brandywine, Red Clay, and White Clay Creek subbasins) drains an area of 76 mi 2 . Streams in the Christina River Basin are used for recreation, drinking water supply, and support of aquatic life. Water quality in some parts of the Christina River Basin is impaired and does not support designated uses of the stream. A multi-agency water-quality management strategy included a modeling component to evaluate the effects of point- and nonpoint-source contributions of nutrients and suspended sediment on stream water quality. To assist in nonpoint-source evaluation, four independent models, one for each of the four main subbasins of the Christina River Basin, were developed and calibrated using the model code Hydrological Simulation Program–Fortran (HSPF). Water-quality data for model calibration were collected in each of the four main subbasins and in small subbasins predominantly covered by one land use following a nonpoint- source monitoring plan. Under this plan, stormflow and base-flow samples were collected during 1998 at two sites in the Christina River subbasin and nine sites elsewhere in the Christina River Basin. The HSPF model for the Christina River subbasin simulates streamflow, suspended sediment, and the nutrients, nitrogen and phosphorus. In addition, the model simulates water temperature, dissolved oxygen, biochemical oxygen demand, and plankton as secondary objectives needed to support the sediment and nutrient simulations. For the model, the basin was subdivided into nine reaches draining areas that ranged from 3.8 to 21.9 mi 2 . Ten different pervious land uses and two impervious land uses were selected for simulation. Land-use areas were determined from 1995 land-use data. The predominant land uses in the Christina River subbasin are residential, urban, forested, agricultural, and open. The hydrologic component of the model was run at an hourly time step and calibrated using streamflow data from two U.S. Geological Survey (USGS) streamflow-measurement stations for the period of October 1, 1994, through October 29, 1998. Daily precipitation data from one National Oceanic and Atmospheric Administration (NOAA) meteorologic station and hourly data from one NOAA meteorologic station were used for model input. The difference between observed and simulated streamflow volume ranged from -2.3 to 5.3 percent for a 10-month portion of the calibration period at the two calibration sites. Annual differences between observed and simulated streamflow generally were greater than the overall error for the 4-year period. For example, at Christina River at Coochs Bridge, near the bottom of the free-flowing part of the subbasin (drainage area of 21 mi 2 ), annual differences between observed and simulated streamflow ranged from -6.9 to 6.5 percent and the overall error for the 4-year period was -1.1 percent. Calibration errors for 36 storm periods at the three calibration sites for total volume, low-flow recession rate, 50-percent lowest flows, 10-percent highest flows, and storm peaks were within the recommended criteria of 20 percent or less. Much of the error in simulating storm events on an hourly time step can be attributed to uncertainty in the rainfall data. The water-quality component of the model was calibrated using nonpoint-source monitoring data collected at two USGS streamflow-measurement stations and other water-quality monitoring data. The period of record for water-quality monitoring was variable at the stations, with a start date ranging from October 1994 to January 1998 and an end date of October 1998. Because of availability, monitoring data for suspended-solids concentrations were used as surrogates for suspended-sediment concentrations, although suspended-solids data may underestimate suspended sediment and affect apparent accuracy of the suspended-sediment simulaion. Comparison of observed to simulated loads for up to six storms in 1998 at the two nonpoint-source monitoring sites (Little Mill Creek near Newport and Christina River at Coochs Bridge, Del.) indicate that simulation error is commonly as large as an order of magnitude for suspended sediment and nutrients. The simulation error tends to be smaller for dissolved nutrients than for particulate nutrients. Errors of 40 percent or less for monthly or annual values indicate a fair to good water-quality calibration according to recommended criteria; much larger errors are possible for individual events. Assessment of the water-quality calibration under stormflow conditions is limited by the relatively small amount of available water-quality data in the subbasin. Users of the Christina River subbasin HSPF model and HSPF models for other subbasins in the Christina River Basin should be aware of model limitations and consider the following if the model is used for predictive purposes: streamflow-duration curves suggest the model simulates streamflow reasonably well when measured over a broad range of conditions and time although streamflow and the corresponding water quality for individual storm events may not be well simulated; streamflow-duration curves for the simulation period compare well with duration curves for the 8-year period ending in 2001 at Christina River at Coochs Bridge, Del., and include all but the extreme high-flow and low-flow events; and calibration for water quality was based on limited data, with the result of increasing uncertainty in the water-quality simulation.

Water-Resources Investigations Report↗

Parking lot runoff quality and treatment efficiencies of a hydrodynamic-settling device in Madison, Wisconsin, 2005-6

A hydrodynamic-settling device was installed in 2004 to treat stormwater runoff from a roof and parking lot located at the Water Utility Administration Building in Madison, Wis. The U.S. Geological Survey, in cooperation with the Wisconsin Department of Natural Resources, the City of Madison, cities in the Waukesha Permit Group, Hydro International, Earth Tech, Inc., National Sanitation Foundation International, and the U.S. Environmental Protection Agency, monitored the device from November 2005 through September 2006 to evaluate it as part of the U.S. Environmental Protection Agency's Environmental Technology Verification Program. Twenty-three runoff events monitored for flow volume and water quality at the device's inlet and outlet were used to calculate the percentage of pollutant reduction for the device. The geometric mean concentrations of suspended sediment (SS), "adjusted" total suspended solids (TSS), total phosphorus (TP), dissolved phosphorus (DP), total recoverable zinc (TZn), and total recoverable copper (TCu) measured at the inlet were 107 mg/L (milligrams per liter), 92 mg/L, 0.17 mg/L, 0.05 mg/L, 38 μg/L (micrograms per liter), and 12 μg/L, respectively, and these concentrations are in the range of values observed in stormwater runoff from other parking lots in Wisconsin and Michigan. Efficiency of the settling device was calculated using the efficiency ratio and summation of loads (SOL) methods. Using the efficiency ratio method, the device reduced concentrations of SS, and DP, by 19, and 15, percent, respectively. Using the efficiency ratio method, the device increased "adjusted" TSS and TZn concentrations by 5 and 19, respectively. Bypass occurred for 3 of the 23 runoff events used in this assessment, and the bypass flow and water-quality concentrations were used to determine the efficiency of the bypass system. Concentrations of SS, "adjusted" TSS, and DP were reduced for the system by 18, 5, and 18, respectively; however, TZn increased by 5 percent. Some of the TSS concentrations were "adjusted" to add the particles that remained on the sieves during sample processing. The loads of SS, "adjusted" TSS, and DP were reduced using the SOL method for the settling device by 38, 9, and 19 percent, respectively, and TZn increased by 13 percent. For the bypass system, the loads of SS, "adjusted" TSS, and DP had percentage reductions of 39, 12, 22, respectively, however TZn increased by 4 percent. The SOL method produced percentage reductions for SS and 'adjusted" TSS that were twice those for the efficiency ratio method. Removing the two large runoff events on August 23 and 24, 2006, from the SOL calculation brought the reduction for SS down to 16 and increased "adjusted" TSS by 4 percent. The two large runoff events were anomalies in that the runoff volumes and dissolved solids concentrations were greatly increased by overflow from an adjacent recycling facility. The SOL method was used to determine the percentage of SS load reduction for six different particle sizes for both the settling device and bypass system. Essentially no load reduction was observed for particles less than 125 micrometers (μm) in diameter, and about a 90-percent reduction occurred for particle sizes greater than 250 μm in diameter. The large removal efficiencies for particle sizes greater than 250 μm in diameter were further supported by the fact that more than 80 percent of the particle sizes trapped in the sump were greater than 250 μm in diameter. These results support the claim by the manufacturer of achieving a large percentage load reduction for particle sizes greater than 250 μm in diameter.

Wisconsin↗

Quality of stormwater runoff discharged from Massachusetts highways, 2005-07

The U.S. Geological Survey (USGS), in cooperation with U.S. Department of Transportation Federal Highway Administration and the Massachusetts Department of Transportation, conducted a field study from September 2005 through September 2007 to characterize the quality of highway runoff for a wide range of constituents. The highways studied had annual average daily traffic (AADT) volumes from about 3,000 to more than 190,000 vehicles per day. Highway-monitoring stations were installed at 12 locations in Massachusetts on 8 highways. The 12 monitoring stations were subdivided into 4 primary, 4 secondary, and 4 test stations. Each site contained a 100-percent impervious drainage area that included two or more catch basins sharing a common outflow pipe. Paired primary and secondary stations were located within a few miles of each other on a limited-access section of the same highway. Most of the data were collected at the primary and secondary stations, which were located on four principal highways (Route 119, Route 2, Interstate 495, and Interstate 95). The secondary stations were operated simultaneously with the primary stations for at least a year. Data from the four test stations (Route 8, Interstate 195, Interstate 190, and Interstate 93) were used to determine the transferability of the data collected from the principal highways to other highways characterized by different construction techniques, land use, and geography. Automatic-monitoring techniques were used to collect composite samples of highway runoff and make continuous measurements of several physical characteristics. Flowweighted samples of highway runoff were collected automatically during approximately 140 rain and mixed rain, sleet, and snowstorms. These samples were analyzed for physical characteristics and concentrations of 6 dissolved major ions, total nutrients, 8 total-recoverable metals, suspended sediment, and 85 semivolatile organic compounds (SVOCs), which include priority polyaromatic hydrocarbons (PAHs), phthalate esters, and other anthropogenic or naturally occurring organic compounds. The distribution of particle size of suspended sediment also was determined for composite samples of highway runoff. Samples of highway runoff were collected year round and under various dry antecedent conditions throughout the 2-year sampling period. In addition to samples of highway runoff, supplemental samples also were collected of sediment in highway runoff, background soils, berm materials, maintenance sands, deicing compounds, and vegetation matter. These additional samples were collected near or on the highways to support data analysis. There were few statistically significant differences between populations of constituent concentrations in samples from the primary and secondary stations on the same principal highways (Mann-Whitney test, 95-percent confidence level). Similarly, there were few statistically significant differences between populations of constituent concentrations for the four principal highways (data from the paired primary and secondary stations for each principal highway) and populations for test stations with similar AADT volumes. Exceptions to this include several total-recoverable metals for stations on Route 2 and Interstate 195 (highways with moderate AADT volumes), and for stations on Interstate 95 and Interstate 93 (highways with high AADT volumes). Supplemental data collected during this study indicate that many of these differences may be explained by the quantity, as well as the quality, of the sediment in samples of highway runoff. Nonparametric statistical methods also were used to test for differences between populations of sample constituent concentrations among the four principal highways that differed mainly in traffic volume. These results indicate that there were few statistically significant differences (Mann-Whitney test, 95-percent confidence level) for populations of concentrations of most total-recoverable metals

Scientific Investigations Report↗

Preliminary assessment of chloride concentrations, loads, and yields in selected watersheds along the Interstate 95 corridor, southeastern Connecticut, 2008-09

Water-quality conditions were assessed to evaluate potential effects of road-deicer applications on stream-water quality in four watersheds along Interstate 95 (I-95) in southeastern Connecticut from November 1, 2008, through September 30, 2009. This preliminary study is part of a four-year cooperative study by the U.S. Geological Survey (USGS), the Federal Highway Administration (FHWA), and the Connecticut Department of Transportation (ConnDOT). Streamflow and water quality were studied at four watersheds?Four Mile River, Oil Mill Brook, Stony Brook, and Jordan Brook. Water-quality samples were collected and specific conductance was measured continuously at paired water-quality monitoring sites upstream and downstream from I-95. Specific conductance values were related to chloride (Cl) concentrations to assist in determining the effects of road-deicing operations on the levels of Cl in the streams. Streamflow and water-quality data were compared with weather data and with the timing, amount, and composition of deicers applied to state highways. Grab samples were collected during winter stormwater-runoff events, such as winter storms or periods of rain or warm temperatures in which melting takes place, and periodically during the spring and summer. Cl concentrations at the eight water-quality monitoring sites were well below the U.S. Environmental Protection Agency (USEPA) recommended chronic and acute Cl toxicity criteria of 230 and 860 milligrams per liter (mg/L), respectively. Specific conductance and estimated Cl concentrations in streams, particularly at sites downstream from I-95, peaked during discharge events in the winter and early spring as a result of deicers applied to roads and washed off by stormwater or meltwater. During winter storms, deicing activities, or subsequent periods of melting, specific conductance and estimated Cl concentrations peaked as high as 703 microsiemens per centimeter (?S/cm) and 160 mg/L at the downstream sites. During most of the spring and summer, specific conductance and estimated Cl concentrations decreased during discharge events because the low-ionic strength of stormwater had a diluting effect on stream-water quality. However, peaks in specific conductance and estimated Cl concentrations at Jordan Brook and Stony Brook corresponded to peaks in streamflow well after winter snow or ice events; these delayed peaks in Cl concentration likely resulted from deicing salts that remained in melting snow piles and (or) that were flushed from soils and shallow groundwater, then discharged downstream. Cl loads in streams generally were highest in the winter and early spring. The estimated load for the period of record at the four monitoring sites downstream from I-95 ranged from 0.33 ton per day (ton/d) at the Stony Brook watershed to 0.59 ton/d at the Jordan Brook watershed. The Cl yields ranged from 0.07 ton per day per square mile (ton/d/)mi2) at Oil Mill Brook, one of the least developed watersheds, to 0.21 (ton/d)/mi2) at Jordan Brook, the watershed with the highest percentage of urban development and impervious surfaces. The median estimates of Cl load from atmospheric deposition ranged from 11 to 19 tons, and contributed 4.3 to 7.1 percent of the Cl load in streamflow from the watershed areas. A comparison of the Cl load input and output estimates indicates that less Cl is leaving the watersheds than is entering through atmospheric deposition and application of deicers. The lag time between introduction of Cl to the watershed and transport to the stream, and uncertainty in the load estimates may be the reasons for this discrepancy. In addition, estimates of direct infiltration of Cl to groundwater from atmospheric deposition, deicer applications, and septic-tank drainfields to groundwater were outside the scope of the November 2008 to September 2009 assessment. However, increased concentrations of ions were observed between upstream and downstream sites and could result from deicer appli

Connecticut↗

Estimating Locations of Perennial Streams in Idaho Using a Generalized Least-Squares Regression Model of 7-Day, 2-Year Low Flows

Many State and Federal agencies use information regarding the locations of streams having intermittent or perennial flow when making management and regulatory decisions. For example, the application of some Idaho water quality standards depends on whether streams are intermittent. Idaho Administrative Code defines an intermittent stream as one having a 7-day, 2-year low flow (7Q2) less than 0.1 ft3/s. However, there is a general recognition that the cartographic representation of perennial/intermittent status of streams on U.S. Geological Survey (USGS) topographic maps is not as accurate or consistent as desirable from one map to another, which makes broad management and regulatory assessments difficult and inconsistent. To help resolve this problem, the USGS has developed a methodology for predicting the locations of perennial streams based on regional generalized least-squares (GLS) regression equations for Idaho streams for the 7Q2 low-flow statistic. Using these regression equations, the 7Q2 streamflow may be estimated for naturally flowing streams in most areas in Idaho. The use of these equations in conjunction with a geographic information system (GIS) technique known as weighted flow accumulation allows for an automated and continuous estimation of 7Q2 streamflow at all points along stream reaches. The USGS has developed a GIS-based map of the locations of streams in Idaho with perennial flow based on a 7Q2 of 0.1 ft3/s and a transition zone of plus or minus 1 standard error. Idaho State cooperators plan to use this information to make regulatory and water-quality management decisions. Originally, 7Q2 equations were developed for eight regions of similar hydrologic characteristics in the study area, using long-term data from 234 streamflow-gaging stations. Equations in five of the regions were revised based on spatial patterns observed in the initial perennial streams map and unrealistic behavior of the equations in extrapolation. The standard errors of prediction for the final equations ranged from a minimum of +75.0 to -42.9 percent in the central part of the study area to a maximum of +277 to -73.5 percent in the southern part of the study area. The equations are applicable only to unregulated, naturally-flowing streams and may produce unreliable results outside the range of explanatory variables used for equation development. Extrapolation outside the range of available data was necessary, however, to predict perennial flow initiation points and transition zones along stream reaches. The map of perennial streams was evaluated by comparing predicted stream classifications with four independent datasets, including field observations by other government agencies. Overall, 81 percent of the comparison data points agreed with the USGS perennial streams model. Regions with the highest number of disagreements had a high percentage of mountainous and forested area with potential mountain front recharge zones, and regions with the highest agreements had a high percentage of low gradient, low elevation area. As a whole, the USGS model predicted a higher number of perennial streams than predictions made with the independent datasets. Some disagreements were due to poor site location coordinates, timing of the comparison site visits during unusually wet or dry years, discrepancies in classification criteria, and variable ground water contributions to flow in some areas. The Idaho Department of Environmental Quality Beneficial Use Reconnaissance Program (BURP) dataset is considered the most representative dataset for comparison because it covered a range of climate conditions and the number of sites visited were consistent from year to year during the study period. Eighty-five percent of BURP comparison data points agreed with the USGS perennial streams model. Although site-specific flow data may be needed to correctly classify streams in some areas, this information rarely is available and is not always practical to o

Scientific Investigations Report↗