USGS Science⌕ Search

SEARCH · USGS Science

Results for “Hydrology and Earth System Sciences (HESS)”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,661 records · Page 49Linked to original sources
USGS2025

Spatiotemporal variability of algal biomass and nitrate in Owasco and Seneca Lakes in the Finger Lakes Region, New York, in 2019

Cyanobacterial harmful algal blooms (CyanoHABs) have become increasingly common, threatening the security of water resources globally. The U.S. Geological Survey conducted high-resolution nearshore mapping surveys using boat-mounted multiparameter sondes and nitrate sensors during the summer and fall of 2019 on Owasco Lake and Seneca Lake, two lakes with documented CyanoHABs in the Finger Lakes region of New York State. Discrete sensor measurements and water-quality samples were collected at fixed points along survey routes and continuous data were generated at open-water monitoring platforms. This investigation examined whether water-quality information from nearshore surveys was representative of open-water conditions and if nearshore surveys could be used to identify areas with localized nearshore CyanoHABs and potential sources of nutrients not captured by tributary sampling. In addition to comparisons across methods, nearshore concentrations of nitrate and chlorophyll were evaluated relative to tributary outlets, cyanobacterial abundance and biovolume at discrete locations, and the locations of near-surface CyanoHABs that were designated as “confirmed with high toxins” by the New York State Department of Environmental Conservation. Nitrate and chlorophyll concentrations were comparable across methods for each lake, although concentration ranges were typically higher for nearshore mapping datasets than for nearshore discrete datasets. Nearshore surveys indicated areas of nitrate enrichment that varied temporally in both lakes. Orthophosphate was not routinely detected. Across methods, median chlorophyll concentrations were higher for the summer survey than for the fall survey in Owasco Lake. Nearshore chlorophyll concentrations varied more temporally in Owasco Lake than in Seneca Lake. Phytoplankton and cyanobacterial abundance and biovolume were about five times higher in Owasco Lake than in Seneca Lake. Cyanobacteria dominated the phytoplankton community in most samples, and Microcystis comprised the bulk of the cyanobacterial biovolume. The most abundant potential cyanotoxin-producing (specifically microcystins) genera were Microcystis , Synechococcus , Aphanocapsa , and Pseudanabaena . The cyanobacterial community composition was comparable between open-water monitoring platforms and nearshore samples. Microcystins were detected in seven survey samples from Owasco Lake, in one survey sample from Seneca Lake, and in one sample each from the open-water monitoring platforms on Owasco and Seneca Lakes that were collected about 7 days before the fall surveys. Microcystin detections were not consistently associated with high cyanobacterial cell counts or cyanotoxin-producing genera. Results from nearshore surveys were comparable to open-water monitoring platforms and discrete nearshore observations in the absence of nearshore or open-water CyanoHABs in these systems during the study. Patterns of nearshore concentrations of nitrate and chlorophyll from nearshore surveys may aid in the identification of areas with localized nitrate loading and shifts in phytoplankton abundance and community composition.

New York↗
USGS2023

Eruptive history of northern Harrat Rahat—Volume, timing, and composition of volcanism over the past 1.2 million years

Harrat Rahat, one of several large, basalt-dominated volcanic fields in the western part of the Kingdom of Saudi Arabia, is a prime example of continental, intraplate volcanism. Excellent exposure makes this an outstanding site to investigate changing volcanic flux and composition through time. We present 93 40 Ar/ 39 Ar ages and 6 36 Cl surface-exposure ages for volcanic deposits throughout northern Harrat Rahat that, integrated with a new geologic map, define 12 eruptive stages. Exposed volcanic deposits in the study area erupted less than 1.2 million years ago (Ma), and 214 of 234 identified eruptions occurred less than 570 thousand years ago (ka). Two eruptions were in the Holocene, including a historically described basaltic eruption in 1256 C.E. and a trachyte eruption newly recognized as Holocene (4.2±5.2 ka). An estimated approximately 82 cubic kilometers (km 3 ; dense rock equivalent) of volcanic products can be documented as having erupted since 1.2 Ma, though this is a lower limit because of concealment of deposits older than 570 ka. Over the last 570 thousand years (k.y.), the average eruption rate was 0.14 cubic kilometers per thousand years (km 3 /k.y.), but volcanism was episodic with periods alternating between low (0.04–0.06 km 3 /k.y.) and high (0.1–0.3 km 3 /k.y.) effusion rates. Before 180 ka, eruptions vented from the volcanic field’s dominant eastern vent axis and from a subsidiary, diffuse, western vent axis. After 180 ka, volcanism focused along the eastern vent axis, and the composition of volcanism varied systematically along its length from basalt dominated in the north to trachyte dominated in the south. We hypothesize that these compositional variations younger than 180 k.y. reflect the growth of a mafic intrusive complex beneath the southern part of the vent axis, which led to the development of evolved magmas. Lastly, these new age data allow for a reassessment of the volcanic recurrence interval at northern Harrat Rahat. Based on available data, volcanism in northern Harrat Rahat over the last 180 k.y. is poorly described using a Poisson distribution with a single recurrence interval. Instead, data for northern Harrat Rahat are better described using a mixed exponential distribution that is applicable for volcanic systems characterized by two different eruptive states, where one state with a longer recurrence interval corresponding to periods of low eruption frequency and one state with a shorter recurrence interval corresponding to periods of high eruption frequency. The preferred model for northern Harrat Rahat over the last 180 k.y. uses a long recurrence interval of 4.0 k.y. and a short recurrence interval of 0.22 k.y.

Professional Paper↗
USGS2025

Chemostratigraphy of the Cretaceous Hue Shale in Arctic Alaska: Exploring paleoceanographic controls on trace element enrichment, organic matter accumulation, and source-rock evolution

We document chemostratigraphy in an outcrop of late Albian to early Campanian (∼103–82 Ma) marine source rocks to better understand paleoenvironmental controls on trace element (TE) enrichment and organic matter accumulation in the distal Colville foreland basin of Arctic Alaska and how those drivers are linked to arc volcanism and successions of Cretaceous oceanographic and climatic biogeochemical events. This unique, 113-m-thick section of Cretaceous Hue Shale deposited during a series of previously undocumented Arctic Cretaceous oceanic anoxic events (Lease et al., 2024) is the only known exposure of thermally immature (0.48–0.52% R o , random vitrinite reflectance) Hue Shale in Arctic Alaska. Strata comprise mainly clay-rich mudstone with elevated total organic carbon (TOC) and hydrogen index values reaching 26.3 wt% (mean = 7.5 wt%) and 689 mg hydrocarbon (HC)/g TOC (mean = 385 mg HC/g TOC), respectively. Maceral composition consists predominantly of fluorescent amorphous organic matter, with abundant brightly fluorescent alginite, including Tasmanites , acritarchs, and Leiosphaeridia . Discrete layers of volcanic ash (preserved as bentonite) are present throughout the section and provide quantitative age control based on U–Pb dates. Chemostratigraphic trends are investigated to advance our understanding of local oceanographic conditions and controls on stratigraphic and temporal heterogeneity of Brookian source rocks. Concurrent sedimentary enrichment in Mo, U, V, Pb, and Cu across the Albian–Cenomanian boundary of the exposed basal gamma-ray zone, may reflect anoxic to euxinic benthic redox conditions favoring organic matter accumulation and preservation. Fluctuating degrees of anoxia-euxinia are inferred throughout the overlying Hue Shale succession, reflected by varying patterns of TE enrichment and TE–TOC covariation. Elevated C org /P molar ratios (>250) across most of the section, with several values exceeding 690, signify that enhanced biological productivity is sustained throughout deposition. Enhanced productivity, recorded by both C org /P and excess Ba, also parallels increases in source rock richness (elevated TOC and S 2 values) during the late Albian–early Cenomanian and late Cenomanian – Turonian. Enhanced productivity and variations in oceanic circulation/stratification likely both drove changes in benthic redox conditions that favored organic carbon accumulation and preservation. Increased continental arc volcanism (e.g., Okhotsk–Chukotka volcanic belt) and High Arctic Large Igneous Province magmatic eruptions throughout the Cretaceous, inferred to have influenced nutrient cycling and local aqueous nutrient availability, also have been invoked as potential drivers of organic carbon burial and source-rock development across the sedimentary sequence. Results presented here document the organic-rich and oil-prone source-rock quality of the Hue Shale in the distal part of the Colville foreland basin and bolster the potential for a Cretaceous petroleum system beneath the eastern North Slope.

Alaska↗
USGS1996

Magnitude and frequency of low flows in the Suwannee River Water Management District, Florida

Low-flow frequency statistics for 20 gaging stations having at least 10 years of continuous record and 31 other stations having less than 10 years of continu ous record or a series of at least two low- flow measurements are presented for unregulated streams in the Suwannee River Water Management District in north-central Florida. Statistics for the 20 continuous-record stations included are the annual and monthly minimum consecutive-day average low- flow magnitudes for 1, 3, 7, 14, and 30 consecutive days for recurrence intervals of 2, 5, 10, 20, and, for some long-term stations, 50 years, based on records available through the 1994 climatic year.Only theannual statistics are given for the 31 other stations; these are for the 7- and 30-consecutive day periods only and for recurrence intervals of 2 and 10 years only. Annual low-flow frequency statistics range from zero for many small streams to 5,500 cubic feet per second for the annual 30- consecutive-day average flow with a recurrenceinterval of 2 years for the Suwannee River near Wilcox (station 02323500). Monthly low-flow frequency statistics range from zero for many small streams to 13,800 cubic feet per second for the minimum 30-consecutive-day average flow with a 2-year recurrence interval for the month of March for the same station. Generally, low-flow characteristics of streams in the Suwannee River Water Management District are controlled by climatic, topographic, and geologic fac tors. The carbonate Floridan aquifer system underlies, or is at the surface of, the entire District. The terrane's karstic nature results in many sinkholes and springs. In some places, springs may contribute greatly to low streamflow and the contributing areas of such springs may include areas outside the presumed surface drainage area of the springs. In other places, water may enter sinkholes within a drainage basin, then reappear in springs downstream from a gage. Many of the smaller streams in the District go dry or have no flow for several months in many years. In addition to the low-flow statistics, four synoptic low-flow measurement surveys were conducted on 161 sites during 1990, 1995, and 1996. The measurements were made to provide "snapshots" of flow conditions of streams throughout the Suwannee River Water Management District. Magnitudes of low flows during the 1990 series of measurements were in the range associated with minimum 7-consecutive-day 50-year recurrence interval to the minimum 7-consecutive-day 20-year recurrence interval, except in Taylor and Dixie Counties, where the magnitudes ranged from the minimum 7-consecutive-day 5-year flow level to the7-consecutive-day 2-year flow level. The magnitudes were all greater than the minimum 7- consecutive-day 2-year flow level during 1995 and 1996. Observations of no flow were recorded at many of the sites for all four series of measurements.

Florida↗
USGS2024

Three-dimensional temperature maps of the Williston Basin, USA: Implications for deep hot sedimentary and enhanced geothermal resources

As part of U.S. Geological Survey's (USGS) efforts to identify and assess geothermal energy resources of the US, a three-dimensional (3D) geologic and thermal model has been constructed for the Williston Basin, USA. The geologic model consists of all sedimentary units above the Proterozoic and Archean crystalline rock (called basement herein), with a total sedimentary thickness of up to 5 km near the basin center. Twenty-nine geologic units were mapped from interpreted formation tops from 16,465 wells. A 3D temperature model was constructed to a depth of 7 km by constructing a 3D heat flow model for the sedimentary units, followed by estimating underlying temperature using a one-dimensional (1D) analytic solution for heat flow within the underlying crystalline basement. Using the sedimentary basin model, heat flow was simulated in 3D and was calibrated using three temperature datasets: 1) 24 high-confidence static temperature logs (equilibrium thermal profiles), 2) more than15,000 drill stem test (DST) measurements from >7,000 wells, and 3) more than 45,000 bottomhole temperature (BHT) measurements from >14,000 wells. The DST and BHT datasets provide broad spatial coverage, but are lower confidence, primarily because measurements were made prior to attaining thermal equilibrium. DST and BHT measurements were binned regionally to develop representative thermal profiles that generally agree with these lower quality data (hereafter called pseudowell temperature profiles). Layer properties (primarily thermal conductivity and compaction curves) were set to best estimate values, then the heat flow model was calibrated to fit pseudowell and static temperature logs primarily by adjusting basal heat flow to approximate the overall temperature profile. Minor adjustments to thermal conductivity allowed adjusting changes in slope at lithologic contacts. Resulting maps include 3D temperature and basal (bottom of sedimentary units) heat flow estimates, which are used as input for the temperature model of the basement. The crystalline basement temperature model uses an analytic 1D solution to the heat flow equation that requires estimates of heat flow and temperature at the upper boundary (i.e., the sediment/basement contact), radiogenic heat production within the crystalline basement, and reference thermal conductivity (i.e., uncorrected for temperature). Two regions of high heat flow are identified: 1) in western North Dakota along the North American Central Plains Conductivity Anomaly and 2) in eastern Montana near the Poplar dome. Within the sedimentary column in the center of the basin of the basin, an area of approximately 100,000 km2 is predicted to have moderate- to high-temperature geothermal resources (>90 °C) under the thickest sequences of sediments. Where thick insulation and high heat flow coincide, electric-grade resources can be less than 4 km deep. Assuming a maximum feasible drilling depth of 7 km, temperatures are predicted to be as high as 175 °C. The geologic model may be used to identify strata at sufficient temperatures that may have natural permeability or that may have conditions that favor development of enhanced/engineered geothermal systems resources.

Montana, North Dakota, South Dakota↗
USGS2024

Quality of groundwater used for domestic supply in the eastern Sacramento Valley and adjacent foothills, California

Summary More than 2 million Californians rely on groundwater from privately owned domestic wells for drinking-water supply. This report summarizes a water-quality survey of domestic and small-system drinking-water supply wells in the eastern Sacramento Valley and adjacent foothills where more than 25,000 residents are estimated to use privately owned domestic wells. Study results show that inorganic and organic constituents in groundwater were present above regulatory (maximum contaminant level, MCL) benchmarks for public drinking-water quality in 8 and 3 percent, respectively, of the aquifer area used for domestic drinking-water supply (herein, “domestic groundwater resources”; fig. 1). The only inorganic constituent detected above regulatory benchmarks was arsenic. The only organic constituent exceeding regulatory benchmarks was the fumigant 1,2,3-trichloropropane (1,2,3-TCP). Three additional organic constituents—the disinfection by-product chloroform, the gasoline oxygenate methyl tert -butyl ether (MTBE), and the solvent tetrachloroethene (PCE)—were detected at low concentrations below one-tenth of regulatory benchmarks in 34, 10, and 10 percent of domestic groundwater resources, respectively. Total dissolved solids (TDS), iron, and manganese exceeded non-regulatory aesthetic guidelines for drinking water in 5, 10, and 26 percent of domestic groundwater resources, respectively. Per- and polyfluoroalkyl substances (PFASs) were detected in 29 percent of domestic groundwater resources,with 5 percent exceeding the recently enacted (April 2024) U.S. Environmental Protection Agency MCLs. Total coliform and enterococci bacteria were detected in 13 and 8 percent of domestic groundwater resources, respectively. Redox sensitive constituents in this study included arsenic, manganese, nitrate, and iron. In the lower elevation portions of the eastern Sacramento Valley study area, reducing conditions in groundwater aquifers promote elevated arsenic, iron, and manganese, and conversely lower concentrations of nitrate. The presence of the volatile organic compound (VOC) 1,2,3-TCP was related to its past history in select agricultural land uses (on orchards or vineyards) in the Sacramento Valley; however, unlike in the San Joaquin Valley where orchards and vineyards are more common, its detection frequency was low (only detected in one well in this study). Chloroform was frequently detected in this study at low levels. Chloroform is a disinfection byproduct commonly found in domestic wells treated by shock chlorination. The solvent PCE is among the most frequently detected VOCs in groundwater, which is primarily related to its long history of use and its persistence in groundwater in oxic conditions. The gasoline oxygenate MTBE was a contaminant introduced to groundwater through atmospheric exchange when it was used as a fuel additive to decrease smog inducing emissions from vehicles. Its occurrence in groundwater at low levels is expected and makes it a potentially useful tracer of relatively recent recharge water being withdrawn from wells. The PFASs are anthropogenic chemicals with hundreds of uses, and they have been incorporated into many different products, processes, and applications worldwide. Like MTBE, the occurrence of PFASs in groundwater may be in part due to atmospheric exchange, but there are several other pathways that contribute PFASs to the environment.

California↗
USGS2000

Natural attenuation of chlorinated volatile organic compounds in ground water at Area 6, Naval Air Station Whidbey Island, Washington

Natural attenuation is a viable alternative to pump and treat for meeting remediation objectives in the vicinity of the southern contaminant plume. The combination of historically low contaminant concentrations in ground water, a landfill cap that limits source area contributions, favorable conditions for degradation of VC, and a relatively long downgradient distance to potential receptors are all favorable for natural attenuation as a remediation alternative. Natural attenuation could effectively meet all but one remediation goal that extraction wells PW- 2, PW-4, PW-6, PW-7, PW-8 and PW-9 are currently being employed to meet. The goal of preventing migration of all VC across the site boundary could not be met by natural attenuation. Some VC would migrate south of the Navy boundary, but the potential for subsequent VC mineralization downgradient of the base and the existing institutional controls would result in minimal additional risk from using natural attenuation. In the western contaminant plume natural attenuation is not currently a viable alternative to pump and treat for meeting remediation objectives. There is a possibility that rates for reductive dechlorination of TCE and TCA could increase substantially if the plume was allowed to migrate beneath the Oak Harbor landfill, but there are not enough data to be certain of such an increase. TCA and TCE concentrations at the leading edge of the western plume need to be reduced to at least 25 and 40 µg/L, respectively, to be protective of potential downgradient receptors. Source area TCA and TCE concentrations have decreased substantially over the past ten years, and the extraction wells PW-3 and PW-5 in particular are removing a significant mass of contaminants from ground water, so natural attenuation may be a viable alternative for the western plume in the future. There would be some possible side benefits of using natural attenuation as an alternative to pump and treat in the southern contaminant plume. The first would be that the resulting decrease in the amount of treated water that would need to be recharged in the swale north of the landfill would result in less off-base migration of contamination across the western site boundary. The second benefit would be a substantial reduction in the amount of dissolved iron and manganese being extracted from the shallow aquifer and run through the treatment system. Removing that source of operation and maintenance problems would result in more effective containment and removal of contamination in the western contaminant plume. The most critical data gap identified in this evaluation is the paucity of contaminant chemistry information downgradient of the Navy boundary in the vicinity of the southern contaminant plume. Without such data, the behavior of the plume and the protectiveness of natural attenuation to downgradient receptors cannot be verified, and field attenuation rates for VC cannot be determined directly. The existing long-term monitoring plan would need to be reviewed and revised if natural attenuation is selected as a remedy for the contamination in the southern plume. In particular, additional performance monitoring wells may be required downgradient of the property.

Washington↗
USGS2026

Bedrock geologic map of the Eagle Lake quadrangle, Essex County, New York

The bedrock geology of the 7.5-minute Eagle Lake quadrangle, Essex County, New York, consists of deformed and metamorphosed Mesoproterozoic gneisses of the Adirondack Highlands unconformably overlain by weakly deformed lower Paleozoic sedimentary rocks of the Champlain Valley. The Mesoproterozoic rocks occur on the eastern edge of the Adirondack Highlands and represent an extension of the Grenville Province of Laurentia. Granulite facies Mesoproterozoic paragneiss, marble, and amphibolite hosted the emplacement of an anorthosite-mangerite-charnockite-granite (AMCG) suite, now exposed mostly as orthogneiss, at approximately 1.18–1.15 giga-annum (Ga, billion years before present). The earliest of four phases of deformation (D1) predated AMCG magmatism and is characterized by gneissosity, rarely preserved F1 isoclinal folds, and migmatite in the paragneiss host rocks. A sample of hornblende quartz syenite from the AMCG suite, collected from an abandoned railroad cut on Old Furnace Road, yielded a U-Pb zircon age of 1,149±10 million years before present. D2 deformation produced a composite penetrative gneissosity, migmatite, and isoclinal F2 folds. Towards the end of D2, felsic magmatism (including the regionally extensive Lyon Mountain Granite Gneiss, abbreviated “LMG”) spread by penetrative migration as semiconcordant alkali feldspar granite sheets subparallel to S2 into the previously deformed lithologies. The LMG crystallized at approximately 1.15 to 1.14 Ga and displays synkinematic F2 folds thus constraining the time of D2 deformation. Exhumation of the Marcy anorthosite began during D3 along a mylonitic extensional detachment, as a type of core complex. Protracted D3 produced F3 folds exhibited in regional domes and basins, such as the Hammondville antiform, reactivation of the S2 foliation, partial melting, metamorphism, metasomatism, iron ore remobilization, and intrusion of magnetite-bearing pegmatite both as layer-parallel sills and crosscutting dikes. D4 created NE- and NW-trending boudinage, local high-grade ductile shear zones, and crosscutting granitic pegmatite dikes. Kilometer (km)-scale lineaments readily observed in lidar data are Ediacaran mafic dikes and Phanerozoic brittle faults. Lower Paleozoic rocks are part of the Early Cambrian to Late Ordovician great American carbonate bank on the ancient margin of Laurentia. The Potsdam Sandstone preserves the Cambrian stratigraphy in outliers above the Great Unconformity. The Paleozoic rocks are weakly folded and block faulted. Parts of the quadrangle are covered by undifferentiated glacial deposits, but much of the quadrangle contains only a variably thick, veneer of unmapped glacial till over significant areas of exposed bedrock. The map also shows waste rock piles and locations of historical mining operations. This study was undertaken to improve our understanding of the bedrock geology in the Adirondack Highlands, establish a modern framework for 1:24,000-scale bedrock geologic mapping in the Adirondack Mountains, and provide a modern context for historical mines. This Scientific Investigations Map of the Eagle Lake 7.5-minute quadrangle consists of a map sheet, an explanatory pamphlet, and a geographic information system database that includes bedrock geologic units, faults, outcrops, and structural geologic information. The map sheet includes a bedrock geologic map, a correlation of map units, a description of map units, an explanation of map symbols, and two cross sections. The explanatory pamphlet includes a discussion of the geology.

New York↗
USGS2024

Status of water-level altitudes and long-term and short-term water-level changes in the Chicot and Evangeline (undifferentiated) and Jasper aquifers, greater Houston area, Texas, 2023

Since the early 1900s, groundwater withdrawn from the primary aquifers that compose the Gulf Coast aquifer system—the Chicot, Evangeline, and Jasper aquifers—has been an important source of water in the greater Houston area, Texas. This report, prepared by the U.S. Geological Survey in cooperation with the Harris-Galveston Subsidence District, City of Houston, Fort Bend Subsidence District, Lone Star Groundwater Conservation District, and Brazoria County Groundwater Conservation District, is one in an annual series of reports depicting the status of water-level altitudes and water-level changes in these aquifers in the greater Houston area. In this report, the Chicot and Evangeline aquifers are treated as a single aquifer for the purposes of providing annual assessments of regional-scale water-level altitudes and water-level changes over time. In 2023, shaded depictions of water-level altitudes for the Chicot and Evangeline aquifers (undifferentiated) ranged from about 286 feet (ft) below the North American Vertical Datum of 1988 (NAVD 88) to about 169 ft above NAVD 88. The largest decline in water-level altitudes indicated by the 1977–2023 long-term water-level-change map was in south-central Montgomery County southeast of The Woodlands. In comparison, the 1990–2023 long-term water-level-change map depicts the largest declines in water-level altitudes in localized areas at or near certain wells in parts of northwestern Harris County and south-central Montgomery County. The largest rise in water-level altitudes for 1977–2023 is depicted in a relatively large area in southeastern Harris County, whereas the largest rise in water-level altitudes for 1990–2023 is depicted in a relatively large area in central Harris County. The 5-year short-term water-level-change map depicts the largest declines at three wells in northern Fort Bend County, one well in western Harris County, and three wells in south-central Montgomery County and the largest rise at one well in central Harris County. The 1-year short-term water-level-change map depicts the largest declines at one well in northern Fort Bend County and two wells in southwestern Harris County and the largest rises at one well in northern Brazoria County and one well in south-central Montgomery County. In 2023, shaded depictions of water-level altitudes for the Jasper aquifer ranged from about 242 ft below NAVD 88 to about 218 ft above NAVD 88. The 2000–23 long-term water-level-change map depicts water-level declines throughout the study area where water-level-measurement data from the aquifer were collected, with the largest declines in north-central Harris County and south-central Montgomery County south of The Woodlands. The 5-year short-term water-level-change map depicts the largest declines at two wells in central Montgomery County near Conroe and two wells in south-central Montgomery County southeast of The Woodlands and the largest rise at one well in western Montgomery County. The 1-year short-term water-level-change map depicts the largest declines at four wells in south-central Montgomery County southeast of The Woodlands and one well in central Montgomery County near Conroe and the largest rises at two wells in western Montgomery County.

Texas↗
USGS2025

Status of water-level altitudes and long-term and short-term water-level changes in the Chicot and Evangeline (undifferentiated) and Jasper aquifers, greater Houston area, Texas, 2024

Since the early 1900s, groundwater withdrawn from the primary aquifers that compose the Gulf Coast aquifer system—the Chicot, Evangeline, and Jasper aquifers—has been an important source of water in the greater Houston area, Texas. This report, prepared by the U.S. Geological Survey in cooperation with the Harris-Galveston Subsidence District, City of Houston, Fort Bend Subsidence District, Lone Star Groundwater Conservation District, and Brazoria County Groundwater Conservation District, is one in an annual series of reports depicting the status of water-level altitudes and water-level changes in these aquifers in the greater Houston area. In this report, the Chicot and Evangeline aquifers are treated as a single aquifer for the purposes of providing annual assessments of regional-scale water-level altitudes and water-level changes over time. In 2024, shaded depictions of estimated water-level altitudes for the Chicot and Evangeline aquifers (undifferentiated) ranged from about 301 feet (ft) below the North American Vertical Datum of 1988 (NAVD 88) to about 184 ft above NAVD 88. The largest decline in water-level altitudes depicted by the 1977–2024 long-term water-level-change map was in south-central Montgomery County. In comparison, the 1990–2024 long-term water-level-change map depicts the largest declines in water-level altitudes in an area northwest of The Woodlands and in an area of northern Waller County. The largest rise in water-level altitudes for 1977–2024 is depicted in an area of east-central Harris County, whereas the largest rise in water-level altitudes for 1990–2024 is depicted in an area of central Harris County. The 5-year short-term water-level-change map depicts the largest declines in several parts of the study area, but these declines are concentrated primarily in northern Fort Bend County, southwestern Harris County, and south-central Montgomery County. The largest rise for 2019–24 is depicted at a well in northern Fort Bend County. The 1-year short-term water-level-change map depicts the largest declines at a well in northern Fort Bend County and a well in west-central Harris County. The largest rise for 2023–24 is depicted at a well in east-central Fort Bend County. In 2024, shaded depictions of estimated water-level altitudes for the Jasper aquifer ranged from about 255 ft below NAVD 88 to about 321 ft above NAVD 88. The 2000–24 long-term water-level-change map depicts the largest water-level decline in an area of central San Jacinto County; the largest rise is depicted in an area of central Grimes County. The 5-year short-term water-level-change map depicts the largest declines across parts of central and southern Montgomery County and at one well in north-central Harris County. The largest rise for 2019–24 is depicted at a well centered on the Montgomery-Grimes County line. The 1-year short-term water-level-change map depicts the largest declines at two wells in south-central Montgomery County and one well in northwestern Montgomery County on the west side of Lake Conroe. The largest rises during 2023–24 are depicted at one well in northwestern Montgomery County and one well in south-central Montgomery County.

Texas↗
USGS2000

Shoals and valley plugs in the Hatchie River watershed

Agricultural land use and gully erosion have historically contributed more sediment to the streams of the Hatchie River watershed than those streams can carry. In 1970, the main sedimentation problem in the watershed occurred in the tributary flood plains. This problem motivated channelization projects (U.S. Department of Agriculture, 1970). By the mid-1980's, concern had shifted to sedimentation in the Hatchie River itself where channelized tributaries were understood to contribute much of the sediment. The Soil Conservation Service [Natural Resources Conservation Service (NRCS) since 1996] estimated that 640,000 tons of bedload (sand) accumulates in the Hatchie River each year and identified roughly the eastern two-thirds of the watershed, where loess is thin or absent, as the main source of sand (U.S. Department of Agriculture, 1986a). The U.S. Geological Survey (USGS), in cooperation with the West Tennessee River Basin Authority (WTRBA), conducted a study of sediment accumulation in the Hatchie River and its tributaries. This report identifies the types of tributaries and evaluates sediment, shoal formation, and valley-plug problems. The results presented here may contribute to a better understanding of similar problems in West Tennessee and the rest of the southeastern coastal plain. This information also will help the WTRBA manage sedimentation and erosion problems in the Hatchie River watershed. The source of the Mississippi section of the Hatchie River is in the sand hills southwest of Corinth, Mississippi (fig. 1). This section of the Hatchie River flows northward in an artificial drainage canal, gathering water from tributary streams that also are channelized. The drainage canal ends 2 miles south of the Tennessee State line. The Tennessee section of the Hatchie River winds north and west in a meandering natural channel to the Mississippi River. Although most of the Hatchie River tributaries are also drainage canals, the river's main stem has kept most of its natural character. The Hatchie River flows through a wide valley bottom occupied mostly by riverine wetland. Historically, the valley bottom has supported hardwood forests. Since publication of the first Hatchie River report (U.S. Department of Agriculture, 1970), the channel of the river has become shallower, and flooding has increased (U.S. Department of Agriculture 1986b). These wetter conditions inhibit growth of hardwoods and lead to premature hardwood mortality. The NRCS has predicted that despite efforts to control erosion in the uplands, most of the valley-bottom forest will die. '...swamping may be so prevalent as to change most of the Hatchie River Basin flood plain into a marsh condition, with the only remnants of the present bottomland hardwood timber remaining. (U.S. Department of Agriculture, 1986b). Loss of channel depth has been concentrated in short reaches near tributary mouths. At the mouths of Richland, Porters, Clover, and Muddy Creeks, navigation has become difficult for recreational users (Johnny Carlin, West Tennessee River Basin Authority, oral commun., 1998). As the low-gradient alluvial system of the Hatchie River accumulates sediment, another common outcome has been the formation of valley plugs, areas where 'channels are filled with sediment, and all the additional bedload brought downstream is then spread out over the flood plain until a new channel has been formed' (Happ, 1975). Valley plugs typically form where the slope of a sand-laden tributary decreases downstream, or where the tributary joins its parent stream (Happ and others, 1940; Diehl, 1994, 1997; Smith and Diehl, 2000).

Mississippi, Tennessee↗
USGS2026

Arsenic and isotope concentrations in the lower Platte River valley of eastern Nebraska, early 1970s to 2023

The City of Lincoln, Nebraska, has been monitoring concentrations of arsenic in their source water and evaluating their options for treatment and removal since at least 2002. In 2022, the City of Lincoln, Nebr., with funding assistance from the Nebraska Water Sustainability Fund, began cooperating with the U.S. Geological Survey to examine arsenic concentrations in surface water and groundwater in the lower Platte River valley and the area around City of Lincoln Water System (LWS) well field. Arsenic data collected from the Platte River since 1974 were examined using the “weighted regression on time, discharge, and season” model, which compared the streamflow (also referred to as “discharge”), time of year, and season to estimate concentrations of arsenic. Annual mean arsenic concentrations modeled for more than 49 years at the Platte River at Louisville, Nebr., U.S. Geological Survey streamgage (station 06805500), indicated a significant increasing trend. Arsenic concentrations in the Platte River were seasonal, with the highest concentrations being observed during mid- to late summer. When seasonal patterns and streamflow were combined with arsenic concentrations in the Platte River during low streamflow conditions, groundwater contributions, which can have higher arsenic concentrations, make up a larger portion of the streamflow. Arsenic samples were collected from upstream rivers in 2022 and 2023 and were paired to analyze the arsenic contributions at the U.S. Geological Survey streamgage on the Platte River near Ashland, Nebr. (station 06801000), near the City of Lincoln well field. The arsenic concentrations from the streamgage on the Platte River near Ashland, Nebr., location, were higher than the U.S. Geological Survey streamgage on the Elkhorn River at Waterloo, Nebr. (station 06800500), and significantly lower than at the U.S. Geological Survey streamgage on the Platte River near Leshara, Nebr.(station 06796500), indicating that the Platte River usually contributes a higher concentration of arsenic than does the Elkhorn River as they join near Ashland, Nebr. During 1991–2023, six groundwater monitoring wells were analyzed to identify trends in arsenic concentrations. Two of the six wells had a positive trend during the 33-year period. One monitoring well did not reveal a long-term trend during this period but showed a trend during 2019–23, correlating to a period when the island in the middle of the Platte River was connected to the east bank of the river when manganese reducing conditions were present and groundwater levels were declining in the well. Across all wells the oxidation and reduction (redox) condition during the time of sampling was assessed. Mixed anoxic and (or) oxic redox condition was the most common redox process and the highest sampled arsenic concentrations in monitoring wells were observed in anoxic conditions driven by manganese reduction. Groundwater arsenic concentrations had seasonal variation around the City of Lincoln well field, with higher arsenic concentrations tending to be further south in comparison to samples collected further north. Isotope samples were collected and analyzed in surface water and groundwater around the LWS well field. The samples indicate that the proportion of surface water present in the LWS production wells can be higher in the spring and lower in the summer. With higher arsenic concentrations observed in the stream water during the summer period, the LWS source water can be affected by these elevated arsenic concentrations even though the proportion of surface water is lower.

Nebraska↗
USGS2026

Hydrogeologic conceptualization of the Arroyos subarea and Northeast Air Force Research Laboratory subarea of the Air Force Research Laboratory, Edwards Air Force Base, Antelope Valley, California, 2017–21

Research and testing within the Air Force Research Laboratory at Edwards Air Force Base in the southwestern Mojave Desert has been conducted since the 1950s. This testing requires large quantities of groundwater for cooling and operations involving hazardous constituents that have entered the groundwater. To better understand the potential movement of contaminants through the groundwater system, the U.S. Geological Survey entered into a cooperative agreement with the U.S. Air Force Civil Engineer Center with the purpose of (1) gaining a more detailed understanding of the hydraulic connection between the unconsolidated basin-fill sediment and the underlying weathered and crystalline bedrock and (2) investigating faults and their potential effect on groundwater flow. This study was specific to the Arroyos subarea and Northeast Air Force Research Laboratory subarea of the Air Force Research Laboratory. The refined hydrogeologic characterization was derived by evaluating surface geologic maps, a regional gravity model, new subsurface geophysical surveys, lithology data from boreholes, and groundwater-level data. Refinement of the hydrogeologic characterization of the study area involved developing a map of basin-fill sediment thickness, estimating the geometry and depth to bedrock, determining the presence of weathered bedrock material, and identifying the location of faults and subsurface structures. The thickness of basin-fill sediment was derived from a regional gravity model. Basin-fill sediment ranges from less than 20 feet (ft) thick to about 150 ft thick and increases substantially toward a deep structural basin in the northwestern part of the study area. The top of bedrock estimated from the new surface geophysical surveys is generally deeper than the top of bedrock from the regional gravity model. These differences in interpreted bedrock tops indicate that there may be a zone of weathered bedrock in the subsurface, overlying crystalline bedrock. Additional subsurface data evaluating the geometry and thickness of weathered bedrock are necessary for a comprehensive evaluation of weathered bedrock in the study area. Previously unmapped extensions of the Leuhman Fault, Spring Fault Zone, and Boron Gate Fault were identified in the new surface geophysical surveys. Evaluation of groundwater flow between bedrock and basin-fill sediment, and the effects of faults on groundwater flow, was done using groundwater-level data from 2020. The groundwater table was in crystalline bedrock throughout most of the Arroyos and Northeast Air Force Research Laboratory subareas, with a few exceptions where it was in basin-fill sediment and weathered bedrock. Basin-fill sediment, and likely weathered bedrock, was partially saturated in parts of the study area where basin-fill sediment was as thick as 150 ft. Weathered bedrock material may be present near the Spring Fault Zone, and if so, was likely saturated in 2020. The groundwater-level data near and within Spring Fault Zone indicate that the Spring Fault Zone acts as a vertical-along-strike conduit for, and as an across-strike impediment to, groundwater flow. In addition, steep groundwater-level gradients in the southeastern part of the study area indicate that a subsurface structure affecting groundwater flow could be related to the Leuhman Fault. Sufficient groundwater-level data were not available to conclusively determine if the Arroyos, Rich, and Boron Gate Faults, and their inferred extensions from the geophysical surveys, affect the movement or direction of groundwater flow.

California↗
USGS2026

Evaluation of stream capture related to groundwater pumping, middle Humboldt River Basin, Nevada

Historical, future, and potential stream capture from groundwater pumping in the middle Humboldt River Basin (MHRB), Nevada, is estimated using a calibrated numerical groundwater flow model. The model was developed to estimate (1) stream capture, which is the change in flux between the groundwater system and the Humboldt River and tributaries, and (2) change in streamflow, which is the change in streamflow estimated for the Imlay gage on the Humboldt River (U.S. Geological Survey streamgage 10333000). Historical stream capture for water years (WYs) 1961–2015 is estimated using recorded and estimated groundwater pumping during that period. Future (predictive) stream capture was based on historical stresses (WYs 1961–2015) using a scenario that simulated non-mine pumping from WY 2015 at a uniform rate for 100 years into the future. Potential stream capture throughout the middle Humboldt River Basin from groundwater pumping during varying durations of time are presented in a series of capture maps. Maps also are presented that show the potential to capture from groundwater evapotranspiration, as well as the storage changes for pumping duration of 100 years. Estimates of historical stream capture from the mainstem Humboldt River during the early 1960s are less than 400 acre-feet per year (acre-ft/yr) when groundwater withdrawals and pumping rates were relatively small compared to more recent times. In the late 1980s and early 1990s, groundwater withdrawals increased and estimated historical stream capture also increased from about 4,000 acre-ft/yr in the late 1980s and early 1990s to as much as 18,800 acre-feet (acre-ft) in WY 1998. In WY 2015, estimated historical stream capture declined to about 13,000 acre-ft because of decreasing groundwater withdrawals and lower streamflow during the drought of WYs 2012–15, resulting in less stream water available for capture. Stream capture was estimated for 100 years into the future based on WY 2015 non-mine pumping rates and mine-dewatering activity through WY 2015. Stream capture is forecast to increase to about 23,000 acre-ft/yr, and streamflow in the Humboldt River could decrease by as much as 19,000 acre-ft/yr. Pumping for mine-dewatering and the associated discharge of that water affects streamflow in the Humboldt River at Imlay, Nevada (U.S. Geological Survey streamgage 10333000). Historically, from WYs 1991 to 2015, streamflow was greater at Imlay gage during active mine-dewatering from mine-water discharge operations and increased by as much as 105,000 acre-ft in WY 1998. The increase was attributed mostly to the discharge of groundwater from mine-related dewatering operations directly into the mainstem Humboldt River or its tributaries, with some of this increase associated with return flows from discharge to rapid infiltration basins. Results indicate that streamflow at Imlay gage is expected to decrease by as much as 1,600 acre-ft/yr 30 years after mine-related pumping and discharge are discontinued. The streamflow reductions at the Imlay gage are expected to then decrease to around 500 acre-ft/yr, 100 years after mine-related pumping and discharge are discontinued. Potential capture maps were produced for pumping durations of 10, 25, 50, and 100 years. Capture map results indicate that areas of greater potential stream capture occur adjacent to the Humboldt River and for upstream tributaries areas north of the Humboldt River.

Nevada↗
USGS2024

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri and Mississippi Rivers on the periphery of Missouri, June 13–22, 2022

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near seven bridges at six highway crossings of the Missouri and Mississippi Rivers on the periphery of Missouri from June 13–22, 2022. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches about 1,640 feet longitudinally and generally extending laterally across the active channel from bank to bank during minor flood-flow conditions. These surveys provided channel geometry and hydraulic conditions at the time of the surveys and provided characteristics of scour holes that may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. These data also may be useful to the Missouri Department of Transportation as a minor flood-flow assessment of the bridges for stability and integrity issues with respect to bridge scour during floods. Bathymetric data were collected around every in-channel pier. Scour holes were present at most piers for which bathymetry could be obtained, except those on banks or surrounded by riprap. Occasionally, scour holes were minor and difficult to discern from nearby dunes and ripples. All bridge sites in this study were surveyed and documented in previous studies. Although partial exposure of substructural support elements was observed at several piers, at most sites the exposure most likely is minimal compared to the overall substructure that remains buried in bed material at these piers. The notable exceptions are piers 12 and 13 at structure L0135 on State Highway 51 at Chester, Illinois, where the bedrock material was fully exposed around the piers. The average difference between the bathymetric surfaces between 2022 and 2018 varied from 0.41 foot higher to 1.86 feet lower. Between 2022 and 2014, the average difference between the bathymetric surfaces varied from 1.02 feet higher to 4.69 feet lower. Only the two sites on the Missouri River and the Caruthersville site were surveyed in 2011; for those sites, the average difference between the bathymetric surfaces varied from 5.83 feet higher to 1.34 feet lower. The most substantial overall net gain of sediment in a reach was between 2011 and 2022 at structure A1700 near Caruthersville, Mo. (site 38). This result was expected because structure A1700 is downstream from the confluences of the Missouri and Ohio Rivers, and therefore subject to the largest streamflows, the largest streamflow fluctuations, and the most substantial sediment flux, as has historically been observed at this site. The presence of riprap blankets, pier size and nose shape, and alignment to flow had a substantial effect on the size of the scour hole observed for a given pier. Piers that were surrounded by riprap blankets had scour holes that were substantially smaller (to nonexistent) compared to piers at which no rock or riprap were present. New riprap blankets were surveyed at pier 3 of structure L0098 at Brownville, Nebraska, and at piers 15–18 of structure A1700 near Caruthersville, Mo., that effectively mitigated the scour holes historically observed at these piers. Narrow piers having round or sharp noses that were aligned with flow often had scour holes that were difficult to discern from nearby bed features, whereas piers having wide or blunt noses resulted in larger, deeper scour holes. Several of the structures had piers that were skewed to primary approach flow. Scour holes near these piers consistently displayed greater depth on the side of the pier with impinging flow and deposition on the leeward side of the pier.

Missouri↗
USGS2026

Preliminary bedrock geologic map of the Port Henry quadrangle, Essex County, New York, and Addison County, Vermont

Introduction The bedrock geology of the 7.5-minute Port Henry quadrangle consists of deformed and metamorphosed Mesoproterozoic gneisses of the Adirondack Highlands unconformably overlain by weakly deformed lower Paleozoic sedimentary rocks of the Champlain Valley. The Mesoproterozoic rocks occur on the eastern edge of the Adirondack Highlands and represent an extension of the Grenville Province of Laurentia. Mesoproterozoic paragneiss, marble, and amphibolite hosted the emplacement of an anorthosite-mangerite-charnockite-granite (AMCG) suite, now exposed mostly as orthogneiss, at approximately 1.18–1.15 Ga (giga-annum). In the Port Henry quadrangle, the AMCG metaigneous rocks (Yhg, Ygb, Yanw) intruded older, mostly metasedimentary rocks of the Grenville Complex during the middle to late Shawinigan orogeny (~1,160–1,150 Ma [mega-annum]). All rocks were subsequently metamorphosed to upper amphibolite to granulite facies conditions during the 1,080–1,050 Ma Ottawan orogeny. New mapping reveals four periods of deformation: (1) D1 produced rarely preserved isoclinal folds in the paragneiss and marble and predates AMCG magmatism. (2) Subsequent D2 deformation produced the dominant gneissic fabric preserved in the rock, recumbent folding, and deformed all the Proterozoic units in the map area. Syn- to late-D2 felsic magmatism resulted in the regionally extensive Lyon Mountain Granite Gneiss, which hosts numerous magnetite ore bodies. (3) Mylonitic extensional shear zones and core complex formation marked the beginning of D3 deformation. Protracted D3 deformation resulted in F3 upright folding, dome and basin formation, pegmatite intrusion, reactivation of the S2 foliation, partial melting, metamorphism, metasomatism, iron-ore remobilization, and intrusion of magnetite-bearing pegmatite both as layer-parallel sills and crosscutting dikes. (4) D4 created northeast- and northwest-trending local high-grade ductile shear zones and boudinage, northwest-trending regional kilometer (km)-wide ductile shear zones, and crosscutting granitic pegmatite dikes. The development of the late-stage regional shear zones (D4) was likely due to the continuation of extensional doming and uplift from upper amphibolite facies conditions at the end of the Ottawan orogeny. The majority of iron-ore deposits in the Port Henry and adjacent Witherbee quadrangles are in the hanging wall of these extensional shear zones. In the Port Henry quadrangle, the km-wide Cheney Mountain shear zone is the result of D4 deformation. Kilometer-scale lineaments readily observed in lidar data are Ediacaran mafic dikes and Phanerozoic brittle faults. The Paleozoic rocks are part of the Early Cambrian to Late Ordovician carbonate bank on the ancient margin of Laurentia. The approximately 1-km-thick Cambrian to Ordovician stratigraphy records a transition from synrift clastics to passive-margin peritidal carbonate buildups to gradually deeper-water subtidal- to shelf-carbonates during foreland basin development associated with the Taconic orogeny. The Paleozoic rocks are weakly folded and block faulted. Large areas of the Champlain Valley are covered by undifferentiated glacial deposits, some of which contain mapped landslides. The map also shows waste rock piles and tailings from historical mining operations. This study was undertaken to improve our understanding of the bedrock geology in the Adirondack Highlands, establish a modern framework for 1:24,000-scale bedrock geologic mapping in the Adirondacks, provide a context for historical iron mines in the eastern Adirondacks, and update the stratigraphy of the Champlain Valley in New York and Vermont. This Open-File Report includes a bedrock geologic map; a description of map units; a correlation of map units; and a geographic information system database that includes bedrock geologic units, faults, outcrops, and structural geologic information.

New York, Vermont↗
USGS2021

Geology, mineralogy, and cassiterite geochronology of the Ayawilca Zn-Pb-Ag-In-Sn-Cu deposit, Pasco, Peru

The Ayawilca deposit in Pasco, Peru, represents the most significant recent base-metal discovery in the central Andes and one of the largest undeveloped In resources globally. As of 2018, it hosts an 11.7 Mt indicated resource grading 6.9% Zn, 0.16% Pb, 15 g/t Ag, and 84 g/t In, an additional 45.0 Mt inferred resource grading 5.6% Zn, 0.23% Pb, 17 g/t Ag, and 67 g/t In, and a separate Sn-Cu-Ag inferred resource of 14.5 Mt grading 0.63% Sn, 0.21% Cu, and 18 g/t Ag. Newly obtained U–Pb dates for cassiterite by LA-ICP-MS (22.77 ± 0.41 and 23.05 ± 2.06 Ma) assign the Ayawilca deposit to the Miocene polymetallic belt of central Peru. The polymetallic mineralization occurs as up to 70-m-thick mantos hosted by carbonate rocks of the Late Triassic to Early Jurassic Pucará Group, and subordinately, as steeply dipping veins hosted by rocks of the Pucará Group and overlying Cretaceous sandstones-siltstones of the Goyllarisquizga Group. Relicts of a distal retrograde magnesian skarn and cassiterite (stage pre-A) were identified in the deepest mantos. The volumetrically most important mineralization at Ayawilca comprises a low-sulfidation assemblage (stage A) with quartz, pyrrhotite, arsenopyrite, chalcopyrite, Fe-rich sphalerite, and traces of stannite and herzenbergite. Stage A sphalerite records progressive Fe depletion, from 33 to 10 mol% FeS, which is compatible with the observed transition from low- to a subsequent intermediate-sulfidation stage (B) marked by the crystallization of abundant pyrite and marcasite. Finally, during a later intermediate-sulfidation stage (C) sphalerite (up to 11 mol% FeS), galena, native bismuth, Cu-Pb-Ag sulfosalts, siderite, Mn-Fe carbonates, kaolinite, dickite, and sericite were deposited. This paragenetic evolution shows striking similarities with that at the Cerro de Pasco Cordilleran-type polymetallic deposit, even if at Ayawilca stage C did not reach high-sulfidation conditions. The occurrence of an early retrograde skarn assemblage suggests that the manto bodies at Ayawilca formed at the transition between distal skarn and skarn-free (Cordilleran-type) carbonate-replacement mineralization. Mineral assemblages define a T- f S 2 evolutionary path close to the pyrrhotite-pyrite boundary. Buffering of hydrothermal fluids by underlying Devonian carbonaceous phyllites of the Excelsior Group imposed highly reduced conditions during stage A mineralization (log f O 2 < − 30 atm). The low f O 2 favored efficient Sn mobility during stages pre-A and A, in contrast to other known ore deposits in the polymetallic belt of central Peru, in which the occurrence of Sn minerals is minor. Subsequent cooling, progressive sealing of vein walls, and decreasing buffering potential of the host rocks promoted the shift from low- (stage A) to intermediate-sulfidation (stages B and C) states. LA-ICP-MS analyses reveal significant In contents in Fe-rich sphalerite (up to 1.7 wt%), stannite (up to 1908 ppm), and chalcopyrite (up to 1185 ppm). The highest In content was found in stage A sphalerite that precipitated along with chalcopyrite and stannite, thus pointing to the early, low-sulfidation assemblage as prospective for this high-tech metal in similar mineral systems. Indium was likely incorporated into the sphalerite crystal lattice via Cu + + In 3+ ↔ 2 Zn 2+ and (Sn, Ge) 4+ + (Ga, In) 3+ + (Cu + Ag) + ↔ 4 Zn 2+ coupled substitutions. Indium incorporation mechanisms into the stannite and chalcopyrite crystal lattices remain unclear.

Pasco↗
USGS2024

Bathymetric and velocimetric surveys at highway bridges crossing the Missouri River between Kansas City and St. Louis, Missouri, May 19–26, 2021

Bathymetric and velocimetric data were collected by the U.S. Geological Survey, in cooperation with the Missouri Department of Transportation, near nine bridges at eight highway crossings of the Missouri River between Kansas City and St. Louis, Missouri, from May 19 to 26, 2021. A multibeam echosounder mapping system was used to obtain channel-bed elevations for river reaches about 1,640 to 1,840 feet (ft) longitudinally and generally extending laterally across the active channel from bank to bank during low to moderate flood-flow conditions. These surveys provided channel geometry and hydraulic conditions at the time of the surveys and provided characteristics of scour holes that may be useful in developing or verifying predictive guidelines or equations for computing potential scour depth. These data also may be useful to the Missouri Department of Transportation as a low to moderate flood-flow assessment of the bridges for stability and integrity issues with respect to bridge scour during floods. Bathymetric data were collected around every in-channel pier. Scour holes were present at most piers for which bathymetry could be obtained, except those on banks or surrounded by riprap. Occasionally, scour holes were minor and difficult to discern from nearby dunes and ripples. All the bridge sites in this study were previously surveyed and documented in previous studies. Comparisons between bathymetric surfaces from the previous surveys and those of the current (2021) study do not indicate any consistent correlation between channel-bed elevations and streamflow conditions. The average difference between the bathymetric surfaces varied from 1.59 ft higher to 0.95 ft lower in 2021 than 2017, which corresponds to a gain of 100,200 cubic yards and a loss of 55,800 cubic yards, respectively. The average difference between the bathymetric surfaces varied from 2.74 ft higher to 3.05 ft lower in 2021 than 2013, which corresponds to a gain of 111,500 cubic yards and a loss of 169,200 cubic yards, respectively. The average difference between the bathymetric surfaces varied from 4.52 ft higher to 1.38 ft lower in 2021 than 2011, which corresponds to a gain of 221,100 cubic yards and a loss of 90,300 cubic yards, respectively. The most substantial overall net gain was 221,100 cubic yards between 2011 and 2021 at structures L0550 and A4497 at Jefferson City (site 20). The large net gain likely results from a combination of the mitigation of the scour holes near pier 4 of both bridges and the substantially lower flow in 2021 than in 2011. Alternatively, the most substantial overall net loss was 169,200 cubic yards between 2013 and 2021 at structure A6288 at Hermann (site 21), despite comparable streamflows. Pier size, nose shape, and skew to approach flow had a substantial effect on the size of the scour hole observed at a given pier. Larger and deeper scour holes were present at piers with wide or blunt noses caused by exposed footings or caissons. When a pier was skewed to primary approach flow, the scour hole was generally deeper and larger than at a similar pier without skew; furthermore, the shape of the scour hole near skewed piers in this study generally was longer and deeper on the side with impinging flow. At structure A6288 at Hermann (site 21), the scour hole near pier 5 was difficult to discern from nearby dunes and ripples, whereas the upstream edge of the footing was visible at pier 4, which likely contributes to the larger scour hole near that pier; the top of the footing may blunt the horseshoe vortex at pier 5, but the exposed front of the footing may exacerbate the vortex at pier 4.

Missouri↗