USGS Science⌕ Search

SEARCH · USGS Science

Results for “Environmental Science Technology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46Linked to original sources
USGS1998

Degradation of chloroacetanilide herbicides: The prevalence of sulfonic and oxanilic acid metabolites in Iowa groundwaters and surface waters

Water samples were collected from 88 municipal wells throughout Iowa during the summer and were collected monthly at 12 stream sites in eastern Iowa from March to December 1996 to study the occurrence of the sulfonic and oxanilic metabolites of acetochlor, alachlor, and metolachlor. The sulfonic and oxanilic metabolites were present in almost 75% of the groundwater samples and were generally present from 3 to 45 times more frequently than their parent compounds. In groundwater, the median value of the summed concentrations of acetochlor, alachlor, and metolachlor was less than 0.05 μg/L, and the median value of the summed concentrations of the six metabolites was 1.2 μg/L. All surface water samples contained at least one detectable metabolite compound. Individual metabolites were detected from 2 to over 100 times more frequently than the parent compounds. In surface water, the median value of the summed concentrations of the three parent compounds was 0.13 μg/L, and the median value of the summed concentrations of the six metabolites was 6.4 μg/L. These data demonstrate the importance of analyzing both parent compounds and metabolites to more fully understand the environmental fate and transport of herbicides in the hydrologic system.

Iowa↗
USGS2011

Environmental policy analysis, peer reviewed: Reservoir sediment cores show US lead declines

As a result of the Clean Air Act, lead (Pb) emissions to the atmosphere have been greatly reduced since the mid-1970s. As part of its National Water Quality Assessment, the U.S. Geological Survey has been using paleolimnological techniques to assess past trends in hydrophobic contaminants. In urban-suburban environments, reservoir sediment cores show prominent peaks in Pb distributions that correlate well with the rise and fall of leaded gasoline. However, Pb concentrations in sediments are approximately double those of baseline values prior to the 1950s and 1960s. It is apparent that significant concentrations of anthropogenic Pb still exist in soils and aquatic sediments and that it will take many years to reduce these concentrations to prepollution values, even if there are no new sources of Pb pollution.

Environmental Science & Technology↗
USGS1998

Natural hydrocarbon background in benthic sediments of Prince William Sound, Alaska: Oil vs coal

The source of the background hydrocarbons in benthic sediments of Prince William Sound (PWS), AK, where the 1989 Exxon Valdez oil spill (EVOS) occurred, has been ascribed to oil seeps in coastal areas of the Gulf of Alaska (GOA). We present evidence that coal is a more plausible source, including (i) high concentrations of total PAH (TPAH), between 1670 and 3070 ng/g, in continental shelf sediments adjacent to the coastal region containing extensive coal deposits; (ii) PAH composition patterns of sediments along with predictive models that are consistent with coal but not oil; (iii) low ratios (<0.2) of triaromatic steranes to methylchrysenes found in sediments and coals, contrasting with the high ratios (11 and 13) found in seep oil; and (iv) bioaccumulation of PAH in salmon collected within 100 m of the Katalla oil seeps but not in filter-feeding mussels collected near oilfield drainages 9 km from the seeps, indicating negligible transport of bioavailable PAH from Katalla seeps to the GOA. In contrast with oil, PAH in coal are not bioavailable, so the presence of coal in these benthic sediments confers no adaptive benefit to biota of the marine ecosystem with respect to PAH insults from anthropogenic sources.The source of the background hydrocarbons in benthic sediments of Prince William Sound (PWS), AK, where the 1989 Exxon Valdez oil spill (EVOS) occurred, has been ascribed to oil seeps in coastal areas of the Gulf of Alaska (GOA). We present evidence that coal is a more plausible source, including (i) high concentrations of total PAH (TPAH), between 1670 and 3070 ng/g, in continental shelf sediments adjacent to the coastal region containing extensive coal deposits; (ii) PAH composition patterns of sediments along with predictive models that are consistent with coal but not oil; (iii) low ratios (<0.2) of triaromatic steranes to methylchrysenes found in sediments and coals, contrasting with the high ratios (11 and 13) found in seep oil; and (iv) bioaccumulation of PAH in salmon collected within 100 m of the Katalla oil seeps but not in filter-feeding mussels collected near oilfield drainages 9 km from the seeps, indicating negligible transport of bioavailable PAH from Katalla seeps to the GOA. In contrast with oil, PAH in coal are not bioavailable, so the presence of coal in these benthic sediments confers no adaptive benefit to biota of the marine ecosystem with respect to PAH insults from anthropogenic sources.

Environmental Science & Technology↗
USGS1998

Airborne pesticide residues along the Mississippi River

The occurrence, concentration, and geographical distribution of agricultural pesticides were determined in air over the Mississippi River from New Orleans, LA, to St. Paul, MN, during the first 10 days of June 1994. Air samples were collected from a research vessel by pulling air through polyurethane foam plugs at about 100 L/min for up to 24 h. Each sample was analyzed for 42 pesticides and 3 pesticide transformation products. Twenty-five compounds 15 herbicides, 7 insecticides, and 3 pesticide transformation products were detected in one or more samples with concentrations ranging from 0.05 to 80 ng/m 3 . Alachlor, chlorpyrifos, diazinon, fonofos, malathion, methyl parathion, metolachlor, metribuzin, pendimethalin, and trifluralin were detected in 80% or more of the samples. The highest concentrations for chlorpyrifos (1.6 ng/m 3 ), diazinon (0.36 ng/m 3 ), and malathion (4.6 ng/m 3 ) all occurred near major metropolitan areas. These samples represent a “snapshot in time”, a spatial and temporal integration of which pesticides were present in the air during each sampling period. The occurrence and atmospheric concentrations of the observed pesticides were most closely related to their use on cropland within 40 km of the river.

Mississippi River↗
USGS1998

Oxalate adsorption at a plagioclase (An47) surface and models for ligand-promoted dissolution

Previous work on adsorption of oxalate at aluminosilicate surfaces suggests that maximum adsorption occurs through a bidentate attachment of the organic ligand, at near-neutral pH. Rates of ligand-promoted dissolution are expected to be greatest at this pH as well. We tested this model by measuring oxalate adsorption on the surface of andesine (An47), in solutions of pH 3- 5 and total oxalate concentrations of 0-8 mM. Contrary to expectation, the greatest adsorption density of 24 ??mol m-2 total oxalate was observed at pH 3 and 8 mM total oxalate. Adsorption is dependent upon the activities of both oxalate (C2O42-) and bioxalate (HC2O4-) in solution and can be modeled with either a two-term Langmuir or a two-term Freundlich isotherm. A Freundlich adsorption model provided the best fit to rate data because it was not constrained to a finite number of adsorption sites, as was the Langmuir model. The two-term ligand adsorption model was incorporated into a rate model: R(tot) = k(H-)[H(ads)/+](L) + k(HOx-)[HOx(ads)/-] + k(Ox2- )[Ox2(ads)/-] where R(tot) is the net dissolution rate of the feldspar, [i(ads)] is the concentration of species i adsorbed to the surface, and k(i) is the rate constant for release of the surface complex. The model was fit to data for oxalate-promoted dissolution of andesine, resulting in estimates for the rate constants of k(HOx-) = 1.16 x 10-12, k(Ox2-) = 1.05 x 10-12, and k(H-) = 9.61 x 10-13 mol of feldspar (??mol of i) (??mol of i)-1 s-1.Previous work on adsorption of oxalate at aluminosilicate surfaces suggests that maximum adsorption occurs through a bidentate attachment of the organic ligand, at near-neutral pH. Rates of ligand-promoted dissolution are expected to be greatest at this pH as well. We tested this model by measuring oxalate adsorption on the surface of andesine (An47), in solutions of pH 3-5 and total oxalate concentrations of 0-8 mM. Contrary to expectation, the greatest adsorption density of 24 ??mol m-2 total oxalate was observed at pH 3 and 8 mM total oxalate. Adsorption is dependent upon the activities of both oxalate (C2O42-) and bioxalate (HC2O4-) in solution and can be modeled with either a two-term Langmuir or a two-term Freundlich isotherm. A Freundlich adsorption model provided the best fit to rate data because it was not constrained to a finite number of adsorption sites, as was the Langmuir model. The two-term ligand adsorption model was incorporated into a rate model: Rtot = kH(+)[Hads+]L +kHOx(-) [HOxads-]+kOx(2-) [Oxads 2-] where Rtot is the net dissolution rate of the feldspar, [iads] is the concentration of species i adsorbed to the surface, and ki is the rate constant for release of the surface complex. The model was fit to data for oxalate-promoted dissolution of andesine, resulting in estimates for the rate constants of kHOx(-) = 1.16??10-12, kOx(2-) = 1.05??10-12, and kH(+) = 9.61??10-13 mol of feldspar (??mol of i)-1 s-1.

Environmental Science & Technology↗
USGS1998

Net trophic transfer efficiency of PCBs to Lake Michigan coho salmon from their prey

Most of the polychlorinated biphenyl (PCB) body burden accumulated by coho salmon ( Oncorhynchus kisutch ) from the Laurentian Great Lakes is from their food. We used diet information, PCB determinations in both coho salmon and their prey, and bioenergetics modeling to estimate the efficiency with which Lake Michigan coho salmon retain PCBs from their food. Our estimate was the most reliable estimate to date because (a) the coho salmon and prey fish sampled during our study were sampled in spring, summer, and fall from various locations throughout the lake, (b) detailed measurements were made on the PCB concentrations of both coho salmon and prey fish over wide ranges in fish size, and (c) coho salmon diet was analyzed in detail from April through November over a wide range of salmon size from numerous locations throughout the lake. We estimated that coho salmon from Lake Michigan retain 50% of the PCBs that are contained within their food.

Environmental Science & Technology↗
USGS1998

Application of the surface complexation concept to complex mineral assemblages

Two types of modeling approaches are illustrated for describing inorganic contaminant adsorption in aqueous environments: (a) the component additivity approach and (b) the generalized composite approach. Each approach is applied to simulate Zn2+ adsorption by a well-characterized sediment collected from an aquifer at Cape Cod, MA. Zn2+ adsorption by the sediment was studied in laboratory batch experiments with a range of pH and Zn(II) concentrations selected to encompass conditions observed in the aquifer. In the generalized composite approach, one, and two-site surface complexation model parameters were calibrated with the experimental data using FITEQL. The pH dependence of Zn2+ adsorption was simulated without explicit representation of electrostatic energy terms. Surface acidity constants and ion pair formation by major electrolyte ions were also not required in the model thereby minimizing the number of fitted parameters. Predictions of Zn2+ adsorption with the component additivity modeling approach did not simulate the experimental data adequately without manipulation of surface area or site density parameter values. To apply the component additivity approach to environmental sorbents, further research is needed to better characterize the composition of sediment surface coatings. The generalized composite modeling approach requires less information and can be viewed as more practical for application within solute transport models. With only three adjustable parameters, this approach could simulate Zn2+ adsorption over a range of chemical conditions that would cause several orders of magnitude variation in the distribution coefficient (K(d)) for Zn2+ within the aquifer.Two types of modeling approaches are illustrated for describing inorganic contaminant adsorption in aqueous environments: (a) the component additivity approach and (b) the generalized composite approach. Each approach is applied to simulate Zn2+ adsorption by a well-characterized sediment collected from an aquifer at Cape Cod, MA. Zn2+ adsorption by the sediment was studied in laboratory batch experiments with a range of pH and Zn(II) concentrations selected to encompass conditions observed in the aquifer. In the generalized composite approach, one- and two-site surface complexation model parameters were calibrated with the experimental data using FITEQL. The pH dependence of Zn2+ adsorption was simulated without explicit representation of electrostatic energy terms. Surface acidity constants and ion pair formation by major electrolyte ions were also not required in the model, thereby minimizing the number of fitted parameters. Predictions of Zn2+ adsorption with the component additivity modeling approach did not simulate the experimental data adequately without manipulation of surface area or site density parameter values. To apply the component additivity approach to environmental sorbents, further research is needed to better characterize the composition of sediment surface coatings. The generalized composite modeling approach requires less information and can be viewed as more practical for application within solute transport models. With only three adjustable parameters, this approach could simulate Zn2+ adsorption over a range of chemical conditions that would cause several orders of magnitude variation in the distribution coefficient (Kd) for Zn2+ within the aquifer.

Environmental Science & Technology↗
USGS1998

Relation of usage to the occurrence of cotton and rice herbicides in three streams of the Mississippi delta

During the 1995 growing season water samples were collected from three streams in the Mississippi delta and were analyzed for selected cotton and rice herbicides and metabolites. The purpose of the study was to relate the use of these herbicides to their occurrence in streams of the delta, to describe how the geochemistry of these herbicides affects their occurrence, and to report the occurrence of selected metabolites. The total concentration of eight herbicides and their metabolites exceeded 5 μg/L throughout most of the growing season with a median total of 15 μg/L. The order of occurrence was molinate > fluometuron > cyanazine > metolachlor > norflurazon > atrazine > prometryn > propanil. The distribution and duration of the total herbicide concentration found in this study are much different from that found in regional studies of herbicides in the U.S. Midwest. In the Midwest, the total herbicide concentration in surface water showed a sharp peak during the spring immediately after application of herbicides to crops, followed by a gradual decrease. In the Mississippi delta, the total herbicide concentration in surface water was more sustained, with multiple peaks due to different application times and postemergent applications to cotton and rice.

Environmental Science & Technology↗
USGS1998

Biodegradation of the surfactant linear alkylbenzenesulfonate in sewage-contaminated groundwater: A comparison of column experiments and field tracer tests

Transport and biodegradation of linear alkylbenzenesulfonate (LAS) in sewage-contaminated groundwater were investigated for a range of dissolved oxygen concentrations. Both laboratory column and an 80-day continuous injection tracer test field experiments were conducted. The rates of LAS biodegradation increased with increasing dissolved oxygen concentrations and indicated the preferential biodegradation of the longer alkyl chain LAS homologues (i.e., C12 and C13) and external isomers (i.e., 2-and 3- phenyl). However, for similar dissolved oxygen concentrations, mass removal rates for LAS generally were 2-3 times greater in laboratory column experiments than in the field tracer test. Under low oxygen conditions (<1 mg/L) only a fraction of the LAS mixture biodegraded in both laboratory and field experiments. Biodegradation rate constants for the continuous injection field test (0.002-0.08 day-1) were comparable to those estimated for a 3-h injection (pulsed) tracer test conducted under similar biogeochemical conditions, indicating that increasing the exposure time of aquifer sediments to LAS did not increase biodegradation rates.Transport and biodegradation of linear alkylbenzenesulfonate (LAS) in sewage-contaminated groundwater were investigated for a range of dissolved oxygen concentrations. Both laboratory column and an 80-day continuous injection tracer test field experiments were conducted. The rates of LAS biodegradation increased with increasing dissolved oxygen concentrations and indicated the preferential biodegradation of the longer alkyl chain LAS homologues (i.e., C12 and C13) and external isomers (i.e., 2- and 3-phenyl). However, for similar dissolved oxygen concentrations, mass removal rates for LAS generally were 2-3 times greater in laboratory column experiments than in the field tracer test. Under low oxygen conditions (<1 mg/L) only a fraction of the LAS mixture biodegraded in both laboratory and field experiments. Biodegradation rate constants for the continuous injection field test (0.002-0.08 day-1) were comparable to those estimated for a 3-h injection (pulsed) tracer test conducted under similar biogeochemical conditions, indicating that increasing the exposure time of aquifer sediments to LAS did not increase biodegradation rates.

Environmental Science & Technology↗
USGS1998

Bacteriophage PRD1 and silica colloid transport and recovery in an iron oxide-coated sand aquifer

Bacteriophage PRD1 and silica colloids were co-injected into sewage-contaminated and uncontaminated zones of an iron oxide-coated sand aquifer on Cape Cod, MA, and their transport was monitored over distances up to 6 m in three arrays. After deposition, the attached PRD1 and silica colloids were mobilized by three different chemical perturbations (elevated pH, anionic surfactant, and reductant). PRD1 and silica colloids experienced less attenuation in the contaminated zone where adsorbed organic matter and phosphate may be hindering attachment of PRD1 and silica colloids to the iron oxide coatings. The PRD1 collision efficiencies agree well with collision efficiencies predicted by assuming favorable PRD1 deposition on iron oxide coatings for which the surface area coverage was measured by microprobe analysis of sediment thin sections. ζ potentials of the PRD1, silica colloids, and aquifer grains corroborated the transport results, indicating that electrostatic forces dominated the attachment of PRD1 and silica colloids. Elevated pH was the chemical perturbation most effective at mobilizing the attached PRD1 and silica colloids. Elevated surfactant concentration mobilized the attached PRD1 and silica colloids more effectively in the contaminated zone than in the uncontaminated zone.

Environmental Science & Technology↗
USGS1998

Enhanced dissolution of cinnabar (mercuric sulfide) by dissolved organic matter isolated from the Florida Everglades

Organic matter isolated from the Florida Everglades caused a dramatic increase in mercury release (up to 35 μM total dissolved mercury) from cinnabar (HgS), a solid with limited solubility. Hydrophobic (a mixture of both humic and fulvic) acids dissolved more mercury than hydrophilic acids and other nonacid fractions of dissolved organic matter (DOM). Cinnabar dissolution by isolated organic matter and natural water samples was inhibited by cations such as Ca 2+ . Dissolution was independent of oxygen content in experimental solutions. Dissolution experiments conducted in DI water (pH = 6.0) had no detectable (<2.5 nM) dissolved mercury. The presence of various inorganic (chloride, sulfate, or sulfide) and organic ligands (salicylic acid, acetic acid, EDTA, or cysteine) did not enhance the dissolution of mercury from the mineral. Aromatic carbon content in the isolates (determined by 13 C NMR) correlated positively with enhanced cinnabar dissolution. ζ-potential measurements indicated sorption of negatively charged organic matter to the negatively charged cinnabar (pH pzc = 4.0) at pH 6.0. Possible mechanisms of dissolution include surface complexation of mercury and oxidation of surface sulfur species by the organic matter.

Florida↗
USGS1998

N2O emissions from a nitrogen-enriched river

Nitrous oxide (N2O) emissions from the South Platte River in Colorado were measured using closed chambers in the fall, winter, and summer of 1994- 1995. The South Platte River was enriched in inorganic N (9-800 ??M) derived from municipal wastewater effluent and groundwater return flows from irrigated agricultural fields. River water was as much as 2500% supersaturated with N2O, and median N2O emission rates from the river surface ranged from less than 90 to 32 600 ??g-N m-2 d-1. Seventy-nine percent of the variance in N2O emission rates was explained by concentrations of total inorganic N in river water and by water temperature. The estimated total annual N2O emissions from the South Platte River were 2 x 1013-6 x 1013 ??g-N yr-1. This amount of annual N2O emissions was similar to the estimated annual N2O emissions from all primary municipal wastewater treatment processes in the United States (1). Results from this study indicate that N-enriched rivers could be important anthropogenic sources of N2O to the atmosphere. However, N2O emission measurements from other N-enriched rivers are needed to better quantify this source.Nitrous oxide (N2O) emissions from the South Platte River in Colorado were measured using closed chambers in the fall, winter, and summer of 1994-1995. The South Platte River was enriched in inorganic N (9-800 ??M) derived from municipal wastewater effluent and groundwater return flows from irrigated agricultural fields. River water was as much as 2500% supersaturated with N2O, and median N2O emission rates from the river surface ranged from less than 90 to 32 600 ??g-N m-2 d-1. Seventy-nine percent of the variance in N2O emission rates was explained by concentrations of total inorganic N in river water and by water temperature. The estimated total annual N2O emissions from the South Platte River were 2??1013-6??1013 ??g-N yr-1. This amount of annual N2O emissions was similar to the estimated annual N2O emissions from all primary municipal wastewater treatment processes in the United States. Results from this study indicate that N-enriched rivers could be important anthropogenic sources of N2O to the atmosphere. However, N2O emission measurements from other N-enriched rivers are needed to better quantify this source.

Environmental Science & Technology↗
USGS1999

New method for the direct determination of dissolved Fe(III) concentration in acid mine waters

A new method for direct determination of dissolved Fe(III) in acid mine water has been developed. In most present methods, Fe(III) is determined by computing the difference between total dissolved Fe and dissolved Fe(II). For acid mine waters, frequently Fe(II) ≫ Fe(III); thus, accuracy and precision are considerably improved by determining Fe(III) concentration directly. The new method utilizes two selective ligands to stabilize Fe(III) and Fe(II), thereby preventing changes in Fe reduction−oxidation distribution. Complexed Fe(II) is cleanly removed using a silica-based, reversed-phase adsorbent, yielding excellent isolation of the Fe(III) complex. Iron(III) concentration is measured colorimetrically or by graphite furnace atomic absorption spectrometry (GFAAS). The method requires inexpensive commercial reagents and simple procedures that can be used in the field. Calcium(II), Ni(II), Pb(II), Al(III), Zn(II), and Cd(II) cause insignificant colorimetric interferences for most acid mine waters. Waters containing >20 mg of Cu/L could cause a colorimetric interference and should be measured by GFAAS. Cobalt(II) and Cr(III) interfere if their molar ratios to Fe(III) exceed 24 and 5, respectively. Iron(II) interferes when its concentration exceeds the capacity of the complexing ligand (14 mg/L). Because of the GFAAS elemental specificity, only Fe(II) is a potential interferent in the GFAAS technique. The method detection limit is 2 μg/L (40 nM) using GFAAS and 20 μg/L (0.4 μM) by colorimetry.

Environmental Science & Technology↗
USGS1999

Occurrence and behavior of the herbicide Prometon in the hydrologic system

Prometon, a triazine herbicide, is used for total vegetation control on industrial sites, on noncrop areas on farms, in and under asphalt, and to a small extent by homeowners. Prometon has often been detected in surface water and groundwater in studies reported in the literature, but its presence is seldom discussed, partly because of its infrequent inclusion on lists of herbicides used in either agricultural or urban areas. In recent large-scale studies by the U.S. Geological Survey, prometon has been the most commonly detected herbicide in surface water and groundwater in urban areas and the third and fourth most commonly detected herbicide in groundwater and surface water, respectively, in agricultural areas. It also has been detected in rain. The frequent detection of prometon in the environment is discussed in relation to its use practices and predicted environmental behavior. Prometon is compared to atrazine, a structurally similar agricultural triazine herbicide that is one of the most studied and most commonly detected herbicides found in the hydrologic environment. The environmental data presented here demonstrate the wide-scale occurrence of prometon in all components of the hydrologic system, particularly in the surface water and groundwater of urban areas.Prometon, a triazine herbicide, is used for total vegetation control on industrial sites, on noncrop areas on farms, in and under asphalt, and to a small extent by homeowners. Prometon has often been detected in surface water and groundwater in studies reported in the literature, but its presence is seldom discussed, partly because of its infrequent inclusion on lists of herbicides used in either agricultural or urban areas. In recent large-scale studies by the U.S. Geological Survey, prometon has been the most commonly detected herbicide in surface water and groundwater in urban areas and the third and fourth most commonly detected herbicide in groundwater and surface water, respectively, in agricultural areas. It also has been detected in rain. The frequent detection of prometon in the environment is discussed in relation to its use practices and predicted environmental behavior. Prometon is compared to atrazine, a structurally similar agricultural triazine herbicide that is one of the most studied and most commonly detected herbicides found in the hydrologic environment. The environmental data presented here demonstrate the wide-scale occurrence of prometon in all components of the hydrologic system, particularly in the surface water and groundwater of urban areas.

Environmental Science & Technology↗
USGS1999

Correlation of soil and sediment organic matter polarity to aqueous sorption of nonionic compounds

Polarities of the soiL/sediment organic matter (SOM) in 19 soil and 9 freshwater sediment sam pies were determined from solid-state 13C-CP/MAS NMR spectra and compared with published partition coefficients (K(oc)) of carbon tetrachloride (CT) from aqueous solution. Nondestructive analysis of whole samples by solid-state NMR permits a direct assessment of the polarity of SOM that is not possible by elemental analysis. The percent of organic carbon associated with polar functional groups was estimated from the combined fraction of carbohydrate and carboxylamide-ester carbons. A plot of the measured partition coefficients (K(oc)) of carbon tetrachloride (CT) vs. percent polar organic carbon (POC) shows distinctly different populations of soils and sediments as well as a roughly inverse trend among the soil/sediment populations. Plots of K(oc) values for CT against other structural group carbon fractions did not yield distinct populations. The results indicate that the polarity of SOM is a significant factor in accounting for differences in K(oc) between the organic matter in soils and sediments. The alternate direct correlation of the sum of aliphatic and aromatic structural carbons with K(oc) illustrates the influence of nonpolar hydrocarbon on solute partition interaction. Additional elemental analysis data of selected samples further substantiate the effect of the organic matter polarity on the partition efficiency of nonpolar solutes. The separation between soil and sediment samples based on percent POC reflects definite differences of the properties of soil and sediment organic matters that are attributable to diagenesis.Polarities of the soil/sediment organic matter (SOM) in 19 soil and 9 freshwater sediment samples were determined from solid-state 13C-CP/MAS NMR spectra and compared with published partition coefficients (Koc) of carbon tetrachloride (CT) from aqueous solution. Nondestructive analysis of whole samples by solid-state NMR permits a direct assessment of the polarity of SOM that is not possible by elemental analysis. The percent of organic carbon associated with polar functional groups was estimated from the combined fraction of carbohydrate and carboxyl-amide-ester carbons. A plot of the measured partition coefficients (Koc) of carbon tetrachloride (CT) vs. percent polar organic carbon (POC) shows distinctly different populations of soils and sediments as well as a roughly inverse trend among the soil/sediment populations. Plots of Koc values for CT against other structural group carbon fractions did not yield distinct populations. The results indicate that the polarity of SOM is a significant factor in accounting for differences in Koc between the organic matter in soils and sediments. The alternate direct correlation of the sum of aliphatic and aromatic structural carbons with Koc illustrates the influence of nonpolar hydrocarbon on solute partition interaction. Additional elemental analysis data of selected samples further substantiate the effect of the organic matter polarity on the partition efficiency of nonpolar solutes. The separation between soil and sediment samples based on percent POC reflects definite differences of the properties of soil and sediment organic matters that are attributable to diagenesis.

Environmental Science & Technology↗
USGS1999

Assessing the influence of reacting pyrite and carbonate minerals on the geochemistry of drainage in the Coeur d'Alene mining district

The relative abundance of minerals that react to generate or consume acid in mineralized areas is critical in determining the quality of water draining from such areas. This work examines the fundamental reactions that influence the pH and composition of drainage from mine adits and tailings piles. We construct triangle diagrams that predict stoichiometric relationships between concentrations of dissolved SO4 dissolved Ca and Mg, and either alkalinity or acidity by considering reactions involving the oxidation of pyrite, dissolution of carbonate minerals, and precipitation of iron oxide and iron hydroxysulfate minerals. Drainage data from the Coeur d'Alene mining district are used to test our stoichiometric approach. Comparisons between theoretical predictions and drainage data indicate that the range of pH values in the mining district is due to reacting pyrite to carbonate mineral ratios that range from near 0/1 to 1/1. Calcite and ankerite are the dominant carbonate minerals that buffer the acid produced during pyrite oxidation and ferrihydrite or schwertmannite precipitation.The relative abundance of minerals that react to generate or consume acid in mineralized areas is critical in determining the quality of water draining from such areas. This work examines the fundamental reactions that influence the pH and composition of drainage from mine adits and tailings piles. We construct triangle diagrams that predict stoichiometric relationships between concentrations of dissolved SO4, dissolved Ca and Mg, and either alkalinity or acidity by considering reactions involving the oxidation of pyrite, dissolution of carbonate minerals, and precipitation of iron oxide and iron hydroxysulfate minerals. Drainage data from the Coeur d'Alene mining district are used to test our stoichiometric approach. Comparisons between theoretical predictions and drainage data indicate that the range of pH values in the mining district is due to reacting pyrite to carbonate mineral ratios that range from near 0/1 to 1/1. Calcite and ankerite are the dominant carbonate minerals that buffer the acid produced during pyrite oxidation and ferrihydrite or schwertmannite precipitation.

Idaho↗
USGS1999

Binding of polychlorinated biphenyls to aquatic humic substances: The role of substrate and sorbate properties on partitioning

Two ortho- (2,2‘,5 and 2,2‘,5,6‘) and a non-ortho- (3,3‘,4,4‘) substituted polychlorinated biphenyl (PCB) congeners were used to study the effects of sorbate structure in binding processes to two lacustrine fulvic acids. Binding constants were determined by solubility enhancement of the solutes by the fulvic acids. The binding of the ortho-trichlorobiphenyl was significantly less than the non-ortho-substituted tetrachlorobiphenyl to both fulvic acids. Surprisingly, the measured ortho-trichlorobiphenyl binding constant to both fulvic acids was approximately the same as the ortho-substituted tetrachlorobiphenyl. The effect of the chlorines in the ortho position inhibits free rotation around the 1,1‘ carbon bond, thereby making the molecule less able to interact effectively with the fulvic acid substrate relative to its non-ortho-substituted congeners. Finally, binding of all three PCBs to the Great Dismal Swamp fulvic acid was significantly higher than for the Pony Lake sample. This observation is attributable to the former substrate's higher degree of aromaticity and polarizability, which can potentially interact more favorably with the PCBs through an increase in van der Waals type interactions.

Environmental Science & Technology↗
USGS1998

Chlorinated ethenes from groundwater in tree trunks

The purpose of this investigation was to determine whether tree-core analysis could be used to delineate shallow groundwater contamination by chlorinated ethenes. Analysis of tree cores from bald cypress [ Taxodium distichum (L.) Rich], tupelo ( Nyssa aquatica L.), sweet gum ( Liquidambar stryaciflua L.), oak ( Quercus spp.), sycamore ( Platanus occidentalis L.), and loblolly pine ( Pinus taeda L.) growing over shallow groundwater contaminated with cis- 1,2-dichloroethene ( c DCE) and trichloroethene (TCE) showed that those compounds also were present in the trees. The cores were collected and analyzed by headspace gas chromatography. Bald cypress, tupelo, and loblolly pine contained the highest concentrations of TCE, with lesser amounts in nearby oak and sweet gum. The concentrations of c DCE and TCE in various trees appeared to reflect the configuration of the chlorinated-solvent groundwater contamination plume. Bald cypress cores collected along 18.6-m vertical transects of the same trunks showed that TCE concentrations decline by 30&minus;70% with trunk height. The ability of the tested trees to take up c DCE and TCE make tree coring a potentially cost-effective and simple approach to optimizing well placement at this site.

Environmental Science & Technology↗