USGS Science⌕ Search

SEARCH · USGS Science

Results for “Water Information Series Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44Linked to original sources
USGS1939

Floods in the Canadian and Pecos River basins of New Mexico, May and June 1937

In May and June floods occurred in the Canadian and Pecos River Basins of New Mexico that were unusually high and in many places were record breaking. The floods were caused by heavy rains that occurred over the eastern part of the State from May 23 to June 4 in a series of intense and intermittent storms. During these storms of the cloudburst type as much as 12 inches of rain fell in the 13-day period, and a fall of 7 inches in 2 hours and 40 minutes was reported from the vicinity of Clayton. Heavy rains also fell in the mountainous region west of Roswell, amounting to as much as l0 inches at some places. Much of the region that had excessive rainfall is relatively flat and has no well-defined drainage system. From these areas there was very little run-off and practically no water was contributed to the major streams. Hail fell at many places in eastern New Mexico, causing damage to crops, livestock, and other property. Hail fell somewhere in the Canadian and Pecos River Basins almost every day during the storm period, but the duration of the fall was generally short. The largest hailstones were reported from Clayton, where one stone measured 8 inches in circumference and weighed 9 ounces; at Centerville, where reports state that some stones were 9 to 10 inches in circumference; and near Roswell, where it was reported that six stones would fill a gallon bucket. The Canadian River flood reached a peak at Logan of 110,000 second-feet, which has been exceeded in this century only by the floods of 1904, 1909, and 1914. The total run-off at Logan for the flood period has been computed as 653,800 acre-feet. At Santa Rosa the Pecos River reached a maximum discharge of 88,200 second-feet, which is greater than any previously recorded. This flood was partly stored in the Alamogordo Reservoir; the peak below the reservoir was only 25,200 second-feet. The Pecos River flood at Roswell reached a maximum discharge of more than 80,000 second-feet. This water came mostly from tributaries that have .their sources in the mountainous area west of Roswell. The Cienaga del Macho, ordinarily a small dry creek, discharged about 49,800 second-feet at its peak. The Rio Hondo experienced several flood peaks, the largest at Roswell probably being near 20,000 second-feet. Berrendo Creek, which enters the Rio Hondo near Roswell, had a computed peak discharge of 37,700 second-feet. Roswell was subjected to several floods that inundated large areas of the town. Considerable damage was done by the water, which covered nearly all the area occupied by the town. Lake McMillan, an artificial reservoir on the Pecos River about 12 miles above Carlsbad, was put to a severe strain by the large quantity of water passing through it, but no serious damage resulted. The capacity of the lake at spillway level is about 39,000 acre-feet, but at the peak of the flood the lake held about 86,000 acre-feet. The total quantity of water passing through the lake during the flood period was more than 440,000 acre-feet. This report presents data pertinent to the floods of May and June 1937, including results of peak discharge determinations made at about 14 miscellaneous places, records of peak stages and discharges and of mean daily discharges during the flood period at 23 regular river-measurement stations, records of rainfall at about 190 places, an isohyetal map showing rainfall over the entire State and two isohyetal maps showing rainfall over the Canadian and Pecos River Basins, and a discussion of the weather conditions during the flood period, including an upper-air wind and pressure chart of the United States for May 28, 1937. In addition to the information listed above the report includes a summary of records of past floods at all places in New Mexico at which authentic records were available.

New Mexico↗
USGS2018

Flood-inundation maps for the Pawtuxet River in West Warwick, Warwick, and Cranston, Rhode Island

A series of 15 digital flood-inundation maps was developed for a 10.2-mile reach of the Pawtuxet River in the municipalities of West Warwick, Warwick, and Cranston, Rhode Island, by the U.S. Geological Survey (USGS), in cooperation with the Rhode Island Emergency Management Agency and the U.S. Army Corps of Engineers. The coverage of the maps extends downstream from Natick Pond dam near State Route 33/Providence Street bridge in West Warwick to the mouth of the river at Pawtuxet Cove (Broad Street bridge) on the border between Cranston and Warwick, R.I. A one-dimensional step-backwater hydraulic model created and calibrated for the Federal Emergency Management Agency Flood Insurance Studies for Kent and Providence Counties in 2015 was updated for this study. The updated hydraulic model reflects the removal of the Pawtuxet Falls dam during 2011 and the raised elevation of a levee surrounding the Warwick Sewer Authority wastewater treatment facility during 2014–17. The hydraulic model was calibrated by using the current (2018) stage-discharge relation at the USGS Pawtuxet River at Cranston, Rhode Island, streamgage (01116500) and documented high-water marks from the March 31, 2010, flood, which had a peak flow greater than the estimated 0.2-percent annual exceedance probability floodflow. The hydraulic model was used to compute water-surface profiles for 15 flood stages at 1-foot (ft) intervals referenced to the USGS Pawtuxet River at Cranston, Rhode Island, streamgage (01116500) and ranging from 8.0 ft (15.2 ft, North American Vertical Datum of 1988), which is the National Weather Service Advanced Hydrologic Prediction Service flood category “action stage,” to 22.0 ft (29.2 ft, North American Vertical Datum of 1988), which is the maximum stage of the stage-discharge relation at the streamgage and exceeds the National Weather Service Advanced Hydrologic Prediction Service flood category “major flood stage” of 13.0 ft. The simulated water-surface profiles were combined with a geographic information system digital elevation model derived from light detection and ranging (lidar) data with a 1.0-ft vertical accuracy to create flood-inundation maps. The flood-inundation maps depict estimates of the areal extent and depth of flooding corresponding to 15 selected flood stages at the streamgage. The flood-inundation maps depict only riverine flooding and do not depict any tidal backwater or coastal storm surge that might occur in the lower part of the river reach. The flood-inundation maps can be accessed through the USGS Flood Inundation Mapping Science website at https://water.usgs.gov/osw/flood_inundation . Near-real-time stages and discharges at the Pawtuxet River streamgage can be obtained from the USGS National Water Information System at https://waterdata.usgs.gov/ . The National Weather Service Advanced Hydrologic Prediction Service provides flood forecasts of stage for this site (CRAR1) at https:/water.weather.gov/ahps/ . The availability of flood-inundation maps referenced to current and forecasted water levels at the USGS Pawtuxet River at Cranston, Rhode Island, streamgage (01116500) can provide emergency management personnel and residents with information that is critical for flood response activities, such as evacuations and road closures, and postflood recovery efforts. The flood-inundation maps are nonregulatory but provide Federal, State, and local agencies and the public with estimates of the potential extent of flooding during flood events.

Rhode Island↗
USGS2004

Summary of studies supporting cumulative effects analysis of upper Yellowstone River channel modifications

During the last several decades, portions of the upper Yellowstone River have been modified for flood control and erosion prevention. The U.S. Army Corps of Engineers is responsible for administration of a permit program for evaluating construction activities affecting rivers, streams, and wetlands. The Corps regulates activities under the authority of Section 10 of the Rivers and Harbors Act and Section 404 of the Clean Water Act. Since assumption of jurisdiction in the mid-1970’s, the Corps has processed a total of 156 permit actions for the upper Yellowstone River. Over two-thirds of the permit actions occurred during or after two consecutive large floods during 1996 and 1997. In response to concern regarding the potential environmental and ecological consequences of channel modification, the Corps, in conjunction with State and local government agencies, initiated a series of scientific studies to better understand the effects of channel modification in the upper Yellowstone River (Figure 1). These included preparation of wetland and riparian inventory maps (Bon, 2001); hydraulic modeling and flood-plain delineation; watershed land-cover assessment (Pick and Potter, 2003); historic bottomland use analysis (Brelsford and others, 2003); analysis of channel modification effects on fish habitat (Bowen and others, 2003); comparison of juvenile salmonid use of modified and unmodified habitats (Zale and Rider, 2003); analysis of riparian vegetation and flood-plain turnover (Merigliano and Polzin, 2003); study of the relations between riparian habitat and bird communities (Hansen and others, 2003); analyses of geomorphology and historical channel changes (Dalby and Robinson, 2003); socioeconomic assessment (BBC Research and Consulting, 2002); and sediment transport investigations and modeling (Holnbeck, 2003). This report is a summary of results from the individual scientific studies as they bear on future programmatic cumulative effects analyses of channel modification of the upper Yellowstone River. We do not attempt a formal, cumulative impact assessment in the sense of evaluating alternatives or future scenarios. The first section presents major findings of the resource studies in terms of temporal comparisons, spatial comparisons, and causal relations. In this section, we present a series of conceptual models or flow diagrams of the major causal pathways of cumulative impacts from channel modification. These represent major pathways of potential impact based on knowledge from other rivers, concerns expressed about the upper Yellowstone, and results from the scientific studies. These diagrams serve to focus interpretation of study results as either supporting or not supporting the importance and magnitude of particular causal relations and to identify key linking variables appearing in multiple causal pathways. These key variables that connect channel modification actions to multiple, valued environmental attributes can serve as the foundation for both projecting and monitoring future responses of the system. A section on analytical realities outlines some of the limitations of projecting cumulative impacts from channel modification of the upper Yellowstone River on meaningful spatial and temporal scales and some of the difficulties of interpreting results from studies conducted shortly after two extreme floods and substantial increases in channel modification. A section on classification describes the two primary geomorphic classification systems of the upper Yellowstone River used in the various individual resource studies. Each of these systems has been valuable in supporting field sampling and expressing results concerning patterns of variation. Their integration or revision into a classification system to achieve some new purpose, such as a regulatory program or monitoring system, will depend on a crisp articulation of riverine management or regulatory objectives. A section on key variables identifies those that are central to the causal pathways connecting channel modification to impacts and provides a rationale for key variables as an alternative to other tools such as Proper Functioning Condition (Barrett and others, 1993), Index of Biotic Integrity (Karr, 1981), or the Synoptic Approach (Liebowitz and others, 1992). This section also explains relations among key variable to Hydrogeomorphic (HGM) assessment procedures (Hauer and Smith, 1998; Hauer and others, 2001) and outlines how these 2 variables might be monitored to track cumulative impacts. Examples of how selected key variables can be quantified using Geographic Information System data sets developed from the resource studies are presented for one reach. The largest portion of the document is an Appendix that summarizes each of the individual scientific studies in terms of scope and methods, findings, principal variables, and metrics used in the study or suggested by the study results, and important needs for further study.

Montana↗
USGS2005

Sediment studies in the Assabet River, central Massachusetts, 2003

From its headwaters in Westborough, Massachusetts, to its confluence with the Sudbury River, the 53-kilometer-long Assabet River passes through a series of small towns and mixed land-use areas. Along the way, wastewater-treatment plants release nutrient-rich effluents that contribute to the eutrophic state of this waterway. This condition is most obvious where the river is impounded by a series of dams that have sequestered large amounts of sediment and support rooted and floating macrophytes and epiphytic algae. The water in parts of these impoundments may also have low concentrations of dissolved oxygen, another symptom of eutrophication. All of the impoundments had relatively shallow maximum water depths, which ranged from approximately 2.4 to 3.4 meters, and all had extensive shallow areas. Sediment volumes estimated for the six impoundments ranged from approximately 380 cubic meters in the Aluminum City impoundment to 580,000 cubic meters in the Ben Smith impoundment. The other impoundments had sediment volumes of 120,000 cubic meters (Powdermill), 67,000 cubic meters (Gleasondale), 55,000 cubic meters (Hudson), and 42,000 cubic meters (Allen Street). The principal objective of this study was the determination of sediment volume, extent, and chemistry, in particular, the characterization of toxic inorganic and organic chemicals in the sediments. To determine the bulk-sediment chemical-constituent concentrations, more than one hundred sediment cores were collected in pairs from the six impoundments. One core from each pair was sampled for inorganic constituents and the other for organic constituents. Most of the cores analyzed for inorganics were sectioned to provide information on the vertical distribution of analytes; a subset of the cores analyzed for organics was also sectioned. Approximately 200 samples were analyzed for inorganic constituents and 100 for organics; more than 10 percent were quality-control replicate or blank samples. Maximum bulk-sediment phosphorus concentrations in surface samples from the impoundments increased along a downstream gradient, with the exception of samples from the last impoundment, where the concentrations decreased. In addition, the highest phosphorus concentrations were generally in the surface samples; this finding may prove helpful if surface dredging is selected as a means to control phosphorus release from sediments. There is no known relation, however, between bulk-sediment concentration of phosphorus and the concentrations of phosphorus available to biota. Potentially toxic metals, including arsenic, cadmium, chromium, copper, nickel, lead, and zinc were frequently measured at concentrations that exceeded U.S. Environmental Protection Agency sediment-quality guidelines for the protection of aquatic life and that occasionally exceeded Massachusetts Department of Environmental Protection guidelines governing landfill disposal (reuse). Due to the effects of matrix interference and sample dilution on laboratory analyses, neither pesticides nor volatile organic compounds were detected at any sites. However, samples collected in other studies from nearby streams indicated the possibility that pesticides might have been detected in the impoundments if not for these analytical problems. Although polychlorinated biphenyl concentrations, as individual Aroclors, generally exceeded published U.S. Environmental Protection Agency guideline concentrations for potential effects on aquatic life, the U.S. Environmental Protection Agency guideline concentrations for human contact or the Massachusetts guidelines for landfill reuse were rarely exceeded. Concentrations of polycyclic aromatic hydrocarbons, both individually and total, frequently were greater than guideline concentrations. Concentrations of total extractable petroleum hydrocarbons did not exceed Massachusetts guideline concentrations in any samples. When the sediment analytes from surface samples are considered togethe

Scientific Investigations Report↗
USGS2015

Simulated responses of streams and ponds to groundwater withdrawals and wastewater return flows in southeastern Massachusetts

Water use, such as withdrawals, wastewater return flows, and interbasin transfers, can alter streamflow regimes, water quality, and the integrity of aquatic habitat and affect the availability of water for human and ecosystem needs. To provide the information needed to determine alteration of streamflows and pond water levels in southeastern Massachusetts, existing groundwater models of the Plymouth-Carver region and western (Sagamore flow lens) and eastern (Monomoy flow lens) Cape Cod were used to delineate subbasins and simulate long-term average and average monthly streamflows and pond levels for a series of water-use conditions. Model simulations were used to determine the extent to which streamflows and pond levels were altered by comparing simulated streamflows and pond levels under predevelopment conditions with streamflows and pond levels under pumping only and pumping with wastewater return flow conditions. The pumping and wastewater return flow rates used in this study are the same as those used in previously published U.S. Geological Survey studies in southeastern Massachusetts and represent the period from 2000 to 2005. Streamflow alteration for the nontidal portions of streams in southeastern Massachusetts was evaluated within and at the downstream outlets of 78 groundwater subbasins delineated for this study. Evaluation of streamflow alteration at subbasin outlets is consistent with the approach used by the U.S. Geological Survey for the topographically derived subbasins in the rest of Massachusetts. The net effect of pumping and wastewater return flows on streamflows and pond levels varied by location and included no change in areas minimally affected by water use, decreases in areas affected more by pumping than by wastewater return flows, or increases in areas affected more by wastewater return flows than by pumping. Simulated alterations to long-term average streamflows at subbasin outlets in response to pumping with wastewater return flows were within about 10 percent of predevelopment streamflows for most of the subbasins in the study area. Alterations ranged from a decrease (depletion) of 43.9 percent at an unnamed tributary to Salt Pond in the Plymouth-Carver region to an increase (surcharge) of 18.2 percent at an unnamed tributary to the Centerville River on western Cape Cod. In general, the relative effects of pumping and wastewater return flows typically were larger in the subbasins with low streamflows than in the subbasins with high streamflows, and there were more depleted streamflows than surcharged streamflows. Increases in streamflows in response to wastewater return flows were generally largest in subbasins with a high density of septic systems or a centralized wastewater treatment facility. For average monthly conditions, streamflow alteration results were similar spatially to results for long-term average conditions. However, differences in the extent of alteration by month were observed; percentage streamflow depletions in most subbasins typically were greatest during the low-streamflow months of August and October. The percentages of the total number of ponds affected by pumping with wastewater return flows under long-term average conditions in the modeled areas were 28 percent for the Plymouth-Carver region, 67 percent for western Cape Cod, and 75 percent for eastern Cape Cod. Pond-level alterations ranged from a decrease of 4.6 feet at Great South Pond in the Plymouth Carver region to an increase of 0.9 feet at Wequaquet Lake in western Cape Cod. The magnitudes of monthly alterations to pond water levels were fairly consistent throughout the year.

Massachusetts↗
USGS2005

Topography and Landforms of Ecuador

EXPLANATION The digital elevation model of Ecuador represented in this data set was produced from over 40 individual tiles of elevation data from the Shuttle Radar Topography Mission (SRTM). Each tile was downloaded, converted from its native Height file format (.hgt), and imported into a geographic information system (GIS) for additional processing. Processing of the data included data gap filling, mosaicking, and re-projection of the tiles to form one single seamless digital elevation model. For 11 days in February of 2000, NASA, the National Geospatial-Intelligence Agency (NGA), the German Aerospace Center (DLR), and the Italian Space Agency (ASI) flew X-band and C-band radar interferometry onboard the Space Shuttle Endeavor. The mission covered the Earth between 60?N and 57?S and will provide interferometric digital elevation models (DEMs) of approximately 80% of the Earth's land mass when processing is complete. The radar-pointing angle was approximately 55? at scene center. Ascending and descending orbital passes generated multiple interferometric data scenes for nearly all areas. Up to eight passes of data were merged to form the final processed SRTM DEMs. The effect of merging scenes averages elevation values recorded in coincident scenes and reduces, but does not completely eliminate, the amount of area with layover and terrain shadow effects. The most significant form of data processing for the Ecuador DEM was gap-filling areas where the SRTM data contained a data void. These void areas are a result of radar shadow, layover, standing water, and other effects of terrain, as well as technical radar interferometry phase unwrapping issues. To fill these gaps, topographic contours were digitized from 1:50,000 - scale topographic maps which date from the mid-late 1980's (Souris, 2001). Digital contours were gridded to form elevation models for void areas and subsequently were merged with the SRTM data through GIS and remote sensing image-processing techniques. The data contained in this publication includes a gap filled, countrywide SRTM DEM of Ecuador projected in Universal Transverse Mercator (UTM) Zone 17 North projection, Provisional South American, 1956, Ecuador datum and a non gap filled SRTM DEM of the Galapagos Islands projected in UTM Zone 15 North projection. Both the Ecuador and Galapagos Islands DEMs are available as an ESRI Grid, stored as ArcInfo Export files (.e00), and in Erdas Imagine (IMG) file formats with a 90 meter pixel resolution. Also included in this publication are high and low resolution Adobe Acrobat (PDF) files of topography and landforms maps in Ecuador. The high resolution map should be used for printing and display, while the lower resolution map can be used for quick viewing and reference purposes.

Data Series↗
USGS2003

Irrigation-induced contamination of water, sediment, and biota in the western United States-synthesis of data from the National Irrigation Water Quality Program

In October 1985 the U.S. Department of the Interior (DOI), through the National Irrigation Water Quality Program (NIWQP), began a series of field investigations at 26 areas in the Western United States to determine whether irrigation drainage has had harmful effects on fish, wildlife, and humans or has reduced beneficial uses of water. In 1992 NIWQP initiated the Data Synthesis Project to evaluate data collected during the field investigations. Geologic, climatologic, and hydrologic data were evaluated and water, sediment, and biota from the 26 areas were analyzed to identify commonalities and dominant factors that result in irrigation-induced contamination of water and biota. Data collected for the 26 area investigations have been compiled and merged into a common data base. The structure of the data base is designed to enable assessment of relations between contaminant concentrations in water, sediment, and biota. The data base is available to the scientific community through the World Wide Web at URL http://www.usbr.gov/niwqp. Analysis of the data base for the Data Synthesis included use of summary statistics, factor analysis, and logistic regression. A Geographic Information System was used to store and analyze spatially oriented digital data such as land use, geology and evaporation rates. In the U.S. Department of the Interior (DOI) study areas, samples of water, bottom sediment, and biota were collected for trace-element and pesticide analysis. Contaminants most commonly associated with irrigation drainage were identified by comparing concentrations in water with established criteria. For surface water, the criteria used were typically chronic criteria for the protection of freshwater aquatic life. Because ground water can discharge to the surface where wildlife can be exposed to it, the criteria used for ground water were both the maximum contaminant levels (MCL's) for drinking water and the chronic criteria for the protection of freshwater aquatic life. Data collected by the NIWQP studies indicated that, in surface water, filtered and unfiltered samples had nearly the same concentrations of arsenic, boron, molybdenum, and selenium for concentrations greater than about 10 micrograms per liter. Therefore, in this concentration range, filtered concentrations can be directly compared to biological-effect levels developed for unfiltered samples. In the range of 1 to 10 micrograms per liter there may be a tendency for unfiltered arsenic concentrations to be greater than filtered concentrations. For selenium, however, the data suggest differences from equality in that range result from analytical imprecision and not a general tendency for unfiltered concentrations to be greater than filtered concentrations. This relation may not be true in lentic, nutrient-rich waters because in such settings algae can bioaccumulate large amounts of selenium and other trace elements. Selenium was the trace element in surface water that most commonly exceeded chronic criteria for the protection of freshwater aquatic life; more than 40 percent of the selenium concentrations in surface-water samples exceeded the U.S. Environmental Protection Agency (USEPA) aquatic-life chronic criterion (5 micrograms per liter). In 12 of the 26 areas at least 25 percent of the surface water-samples had selenium concentrations that either equaled or exceeded the chronic criterion (5 micrograms per liter). More than 28 percent of boron concentrations and almost 17 percent of the molybdenum concentrations exceeded the aquatic life criteria established by the State of California (550 and 19 micrograms per liter, respectively). In ground water, more than 22 percent of the arsenic concentrations and more than 35 percent of the selenium concentrations exceeded the MCL (10 and 50 micrograms per liter, respectively). Few samples of uranium in surface water exceeded a criterion for the protection of aquatic life (300 micrograms per liter), but 44 percent

Professional Paper↗
USGS2012

Archive of digital boomer subbottom profile data collected in the Atlantic Ocean offshore northeast Florida during USGS cruises 03FGS01 and 03FGS02 in September and October of 2003

In September and October of 2003, the U.S. Geological Survey (USGS), in cooperation with the Florida Geological Survey, conducted geophysical surveys of the Atlantic Ocean offshore northeast Florida from St. Augustine, Florida, to the Florida-Georgia border. This report serves as an archive of unprocessed digital boomer subbottom profile data, trackline maps, navigation files, Geographic Information System (GIS) files, Field Activity Collection System (FACS) logs, and formal Federal Geographic Data Committee (FGDC) metadata. Filtered and gained (a relative increase in signal amplitude) digital images of the seismic profiles are also provided. Refer to the Acronyms page for expansions of all acronyms and abbreviations used in this report. The USGS St. Petersburg Coastal and Marine Science Center (SPCMSC) assigns a unique identifier to each cruise or field activity. For example, 03FGS01 tells us the data were collected in 2003 as part of cooperative work with the Florida Geological Survey (FGS) and that the data were collected during the first field activity for that project in that calendar year. Refer to http://walrus.wr.usgs.gov/infobank/programs/html/definition/activity.html for a detailed description of the method used to assign the field activity identification (ID). The naming convention used for each seismic line is as follows: yye##a, where 'yy' are the last two digits of the year in which the data were collected, 'e' is a 1-letter abbreviation for the equipment type (for example, b for boomer), '##' is a 2-digit number representing a specific track, and 'a' is a letter representing the section of a line if recording was prematurely terminated or rerun for quality or acquisition problems. The boomer plate is an acoustic energy source that consists of capacitors charged to a high voltage and discharged through a transducer in the water. The transducer is towed on a sled floating on the water surface and when discharged emits a short acoustic pulse, or shot, which propagates through the water, sediment column, or rock beneath. The acoustic energy is reflected at density boundaries (such as the seafloor, sediment, or rock layers beneath the seafloor), detected by hydrophone receivers, and recorded by a PC-based seismic acquisition system. This process is repeated at timed intervals (for example, 0.5 seconds) and recorded for specific intervals of time (for example, 100 milliseconds). In this way, a two-dimensional (2-D) vertical profile of the shallow geologic structure beneath the ship track is produced. Refer to the handwritten FACS operation log (PDF, 442 KB) for diagrams and descriptions of acquisition geometry, which varied throughout the cruises. Table 1 displays a summary of acquisition parameters. See the digital FACS equipment logs (PDF, 9-13 KB each) for details about the acquisition equipment used. The archived trace data are in standard Society of Exploration Geophysicists (SEG) SEG Y (Barry and others, 1975) format (rev. 0), except for the first 3,200 bytes of the card image header, which are stored in ASCII format instead of the standard EBCDIC format. The SEG Y files may be downloaded and processed with commercial or public domain software such as Seismic Unix (SU) (Cohen and Stockwell, 2005). See the How To Download SEG Y Data page for download instructions. The printable profiles provided here are Graphics Interchange Format (GIF) images that were filtered and gained using SU software. Refer to the Software page for details about the processing and links to example SU processing scripts and USGS software for viewing the SEG Y files (Zihlman, 1992).

Florida;Georgia↗
USGS2006

USGS Streamgages Linked to the Medium Resolution NHD

The locations of approximately 23,000 current and historical U.S. Geological Survey (USGS) streamgages in the United States and Puerto Rico (with the exception of Alaska) have been snapped to the medium resolution National Hydrography Dataset (NHD). The NHD contains geospatial information about mapped surface-water features, such as streams, lakes, and reservoirs, etc., creating a hydrologic network that can be used to determine what is upstream or downstream from a point of interest on the NHD network. An automated snapping process made the initial determination of the NHD location of each streamgage. These initial NHD locations were comprehensively reviewed by local USGS personnel to ensure that streamgages were snapped to the correct NHD reaches. About 75 percent of the streamgages snapped to the appropriate NHD reach location initially and 25 percent required adjustment and relocation. This process resulted in approximately 23,000 gages being successfully snapped to the NHD. This dataset contains the latitude and longitude coordinates of the point on the NHD to which the streamgage is snapped and the location of the gage house for each streamgage. A process known as indexing may be used to create reference points (event tables) to the NHD reaches, expressed as a reach code and measure (distance along the reach). Indexing is dependent on the version of NHD to which the indexing is referenced. These data are well suited for use in indexing because nearly all the streamgage NHD locations have been reviewed and adjusted if necessary, to ensure they will index to the appropriate NHD reach. Flow characteristics were computed from the daily streamflow data recorded at each streamgage for the period of record. The flow characteristics associated with each streamgage include: *First date (year, month, day) of streamflow data *Last date (year, month, day) of streamflow data *Number of days of streamflow data *Number of days of non-zero streamflow data *Minimum and maximum daily flow for the period of record (cubic feet per second) *Percentiles (1, 5, 10, 20, 25, 50, 75, 80, 90, 95, 99) of daily flow for the period of record (cubic feet per second) *Average and standard deviation of daily flow for the period of record (cubic feet per second) *Mean annual base-flow index (BFI) computed for the period of record (fraction, ranging from 0 to 1) *Year-to-year standard deviation of the annual base-flow index computed for the period of record (fraction) *Number of years of data used to compute the base-flow index (years) The streamflow data used to compute flow characteristics were copied from the NWIS-Web historical daily discharge archive (nadww01.er.usgs.gov:/www/htdocs/nwisweb/data/discharge) on June 15, 2005.

Data Series↗
USGS2015

Evaluation of stream flow effects on smolt survival in the Yakima River Basin, Washington, 2012-2014

The influence of stream flow on survival of emigrating juvenile (smolts) Pacific salmon Oncorhynchus spp. and steelhead trout O. mykiss is of key management interest. However, few studies have quantified flow effects on smolt migration survival, and available information does not indicate a consistent flow-survival relationship within the typical range of flows under management control. It is hypothesized that smolt migration and dam passage survival are positively correlated with stream flow because higher flows increase migration rates, potentially reducing exposure to predation, and reduce delays in reservoirs. However, available empirical data are somewhat equivocal concerning the influence of flow on smolt survival and the underlying mechanisms driving this relationship. Stream flow effects on survival of emigrating anadromous salmonids in the Yakima Basin have concerned water users and fisheries managers for over 20 years, and previous studies do not provide sufficient information at the resolution necessary to inform water operations, which typically occur on a small spatiotemporal scale. Using a series of controlled flow releases from 2012-2014, combined with radio telemetry, we quantified the relationship between flow and smolt survival from Roza Dam 208 km downstream to the Yakima River mouth, as well as for specific routes of passage at Roza Dam. A novel multistate mark-recapture model accounted for weekly variation in flow conditions experienced by radio-tagged fish. Groups of fish were captured and radio-tagged at Roza Dam and released at two locations, upstream at the Big Pines Campground (river kilometer [rkm] 211) and downstream in the Roza Dam tailrace (rkm 208). A total of 904 hatchery-origin yearling Chinook salmon O. tshawytscha were captured in the Roza Dam fish bypass, radio-tagged and released upstream of Roza Dam. Two hundred thirty seven fish were released in the tailrace of Roza Dam. Fish released in the tailrace of Roza Dam were tagged concurrently with fish released upstream of the dam using identical tagging methods. Tagging and release events were conducted to target a range of flow conditions indicative of flows observed during the typical migration period (March-May) for juvenile spring Chinook salmon in the Yakima River. Three, five and four separate upstream releases were conducted in 2012, 2013, and 2014 respectively, and at least 43 fish were released alive on each occasion. The release sample sizes in 2014 were much larger (~130) compared to previous years for the purpose of increasing precision of survival estimates across the range of flows tested. Migration movements of radio-tagged spring Chinook salmon smolts were monitored with an array of telemetry receiver stations (fixed sites) that extended 208 rkm downstream from the forebay of Roza Dam to the mouth of the Yakima River. Fixed monitoring sites included the forebay of Roza Dam (rkm 208), the tailrace of Roza Dam (rkm 207.9), the mouth of Wenas Creek (rkm 199.2), the mouth of the Naches River (two sites, rkm 189.4), Sunnyside Dam (two sites, rkm 169.1), Prosser Dam (rkm 77.2), and the mouth of the Yakima River (two sites, rkm2 3). This array segregated the study area into four discrete reaches in which survival of tagged fish was estimated. Aerial and underwater antennas were also used to monitor tagged fish at Roza Dam. Aerial antennas were located in the forebay, on the East gate, on the West gate, and in the tailrace of Roza Dam. Underwater antennas were located in the fish bypass, upstream of the East gate, and upstream of the West gate to collect route-specific passage data for tagged fish. Additional years of data collection and analysis could alter or improve our understanding of the influence of flow and other environmental factors on smolt survival in the Yakima River. Nevertheless, during 2012-2014, yearling hatchery Chinook salmon smolt emigration survival was significantly associated with stream flow in the

Report↗
USGS2019

Hydrogeologic framework of the Virginia Eastern Shore

The Yorktown-Eastover aquifer system of the Virginia Eastern Shore consists of upper, middle, and lower confined aquifers overlain by correspondingly named confining units and underlain by the Saint Marys confining unit. Miocene- to Pliocene-age marine-shelf sediments observed in 205 boreholes include medium- to coarse-grained sand and shells that compose the aquifers and fine-grained sand, silt, and clay that compose the confining units. The upper confining unit also includes fine-grained and organic-rich back-barrier and estuarine sediments of Pleistocene age. An overlying surficial aquifer is composed mostly of Pleistocene-age nearshore sand and gravel with smaller amounts of cobbles and boulders. In addition, Pleistocene-age sediments that fill three buried paleochannels are for the first time explicitly delineated here as distinct hydrogeologic units. Two aquifers are composed of medium- to coarse-grained fluvial sand and gravel, and an intervening confining unit is composed of fine-grained estuarine sand, silt, clay, and organic material. Aquifer and confining-unit sediments are also mixed with reworked marine-shelf sediments eroded from the sides of the paleochannels. Hydrogeologic units of the Yorktown-Eastover aquifer system generally dip eastward, are as much as several tens of feet thick, and have an undulating configuration possibly resulting from the underlying Chesapeake Bay impact crater. Aquifers and confining units are incised by the three paleochannels along an upward-widening and eastward-lengthening series of structural “windows.” Hydrogeologic units within mainstems and branching tributaries of the paleochannels dip southeastward parallel to slopes of the paleochannels, are as much as several tens of feet thick, and laterally abut the Yorktown-Eastover aquifer system along paleochannel sidewalls. The Yorktown-Eastover aquifer system is thereby hydraulically breached by the paleochannels to alternately create barriers to or conduits for groundwater flow. Results of previously documented aquifer tests at 58 wells indicate that transmissivity is generally greatest in young, shallow, and coarse-grained nearshore and fluvial sediments of the surficial aquifer and paleochannels. Transmissivity progressively decreases with depth in older, deeper, and finer grained marine-shelf sediments of the Yorktown-Eastover aquifer system, probably because they have undergone compaction as a result of greater overburden pressure over longer periods of time. Compiled chloride concentrations in samples from 330 wells generally increase downward, with most of the samples collected at altitudes above −300 feet and with most concentrations less than 250 milligrams per liter. The saltwater-transition zone has a broad trough-like shape aligned with the peninsula, being relatively shallow along the coastline and deeper along the central “spine.” Because movement of the saltwater is slow, the configuration largely reflects groundwater flow prior to widespread groundwater withdrawals. Fresh groundwater has leaked downward along deep parts of the saltwater-transition zone and leaked upward along shallower parts to discharge at the coast. The saltwater-transition zone also exhibits an anomalous ridge across the center of the peninsula. Groundwater levels indicate that the saltwater ridge formed primarily by the Exmore paleochannel acting as a large lateral collector drain. Groundwater levels were lowered, and the position of saltwater-transition zone was elevated, by a flow conduit that intercepted groundwater that otherwise would have flowed toward and discharged along the coastline. Nearly all freshwater on the Virginia Eastern Shore is supplied by groundwater withdrawals, which have lowered water levels, altered hydraulic gradients, and created a concern for saltwater intrusion. Previous characterizations of groundwater conditions that are relied on to manage groundwater development have been limited by a lack of hydrogeologic information, particularly data on buried paleochannels that are critical to safeguarding the groundwater supply. Using recently available expanded information, the U.S. Geological Survey undertook a study in cooperation with the Virginia Department of Environmental Quality during 2016–19 to develop an improved description of the groundwater system called a “hydrogeologic framework.” The hydrogeologic framework can aid water-supply planning and development by providing information on broad trends in aquifer configurations, hydraulic properties, and proximity to saltwater to avoid chloride contamination. Digital models to evaluate effects of groundwater withdrawals can also be improved with expanded data and capabilities to evaluate paleochannel hydraulic connections and the potential for saltwater movement. The hydrogeologic framework is limited by the nonuniform distribution of boreholes and the subjective delineation of aquifers and confining units, including those within paleochannels that are regarded as preliminary. The configuration of the saltwater-transition zone is also regarded as preliminary because of the nonuniform distribution of groundwater samples. Low well-sampling frequency precludes characterizing movement of the saltwater-transition zone. A monitoring strategy of sampling and possibly electromagnetic-induction well logging could be used to detect saltwater movement.

Virginia↗
USGS2016

Isotopic composition of ice cores and meltwater from upper fremont glacier and Galena Creek rock glacier, Wyoming

Meltwater runoff from glaciers can result from various sources, including recent precipitation and melted glacial ice. Determining the origin of the meltwater from glaciers through isotopic analysis can provide information about such things as the character and distribution of ablation on glaciers. A 9.4 m ice core and meltwater were collected in 1995 and 1996 at the glacigenic Galena Creek rock glacier in Wyoming's Absaroka Mountains. Measurements of chlorine‐36 ( 36 Cl), tritium ( 3 H), sulphur‐35 ( 35 S), and delta oxygen‐18 (δ 18 O) were compared to similar measurements from an ice core taken from the Upper Fremont Glacier in the Wind River Range of Wyoming collected in 1991–95. Meltwater samples from three sites on the rock glacier yielded 36 Cl concentrations that ranged from 2.1±1.0×10 6 to 5.8±0.3×10 6 atoms/l. The ice‐core 36 Cl concentrations from Galena Creek ranged from 3.4±0.3×10 5 to 1.0±0.1×10 6 atoms/l. Analysis of an ice core from the Upper Fremont Glacier yielded 36 Cl concentrations of 1.2±0.2×10 6 and 5.2±0.2×10 6 atoms/l for pre‐1940 ice and between 2 ×10 6 and 3×10 6 atoms/l for post‐1980 ice. Purdue's PRIME Lab analyzed the ice from the Upper Fremont Glacier. The highest concentration of 36 Cl in the ice was 77±2×10 6 atoms/l and was deposited during the peak of atmospheric nuclear weapons testing in the late 1950s. This is an order of magnitude greater than the largest measured concentration from both the Upper Fremont Glacier ice core that was not affected by weapons testing fallout and the ice core collected from the Galena Creek rock glacier. Tritium concentrations from the rock glacier ranged from 9.2±0.6 to 13.2±0.8 tritium units (TU) in the meltwater to −1.3±1.3 TU in the ice core. Concentrations of 3 H in the Upper Fremont Glacier ice core ranged from 0 TU in the ice older than 50 years to 6–12 TU in the ice deposited in the last 10 years. The maximum 3H concentration in ice from the Upper Fremont Glacier deposited in the early 1960s during peak weapons testing fallout for this isotope was 360 TU. One meltwater sample from the rock glacier was analyzed for 35 S with a measured concentration of 5.4±1.0 millibecquerel per liter (mBeq/l). Modern precipitation in the Rocky Mountains contains 35 S from 10 to 40 mBeq/L. The δ 18 O results in meltwater from the Galena Creek rock glacier (−17.40±0.1 to −17.98±0.1 per mil) are similar to results for modern precipitation in the Rocky Mountains. Comparison of these isotopic concentrations from the two glaciers suggest that the meltwater at the Galena Creek site is composed mostly of melted snow and rain that percolates through the rock debris that covers the glacier. Additionally, this water from the rock debris is much younger (less than two years) than the reported age of about 2000 years for the subsurface ice at the mid‐glacier coring site. Thus the meltwater from the Galena Creek rock glacier is composed primarily of melted surface snow and rain water rather than melted glacier ice, supporting previous estimates of slow ablation rates beneath the surface debris of the rock glacier.

Geografiska Annaler, Series A: Physical Geography↗
USGS2010

Changes in streamflow and the flux of nutrients in the Mississippi-Atchafalaya River Basin, USA, 1980-2007

Nutrients and freshwater delivered by the Mississippi and Atchafalaya Rivers drive algal production in the northern Gulf of Mexico, which eventually results in the widespread occurrence of hypoxic bottom waters along the Louisiana and Texas coast. Researchers have demonstrated a relation between the extent of the hypoxic zone and the magnitude of streamflow, nutrient fluxes, and nutrient concentrations in the Mississippi River, with springtime streamflows and fluxes being the most predictive. In 1999 the U.S. Geological Survey (USGS) estimated the flux of nitrogen, phosphorus, and silica at selected sites in the Mississippi Basin and to the Gulf of Mexico for 1980-1996. These flux estimates provided the baseline information used by the Mississippi River/Gulf of Mexico Watershed Nutrient Task Force to develop an Action Plan for reducing hypoxia in the northern Gulf of Mexico. The primary goal of the Action Plan was to achieve a reduction in the size (areal extent) of the hypoxic zone from an average of approximately 14,000 square kilometers in 1996-2000 to a 5-year moving average of less than 5,000 square kilometers by 2015. Improved statistical models and adjusted maximum likelihood estimation using USGS Load Estimator (LOADEST) software were used to estimate annual and seasonal nutrient fluxes for 1980-2007 at selected sites on the Mississippi River and its tributaries. These data provide a means to evaluate the influence of natural and anthropogenic effects on delivery of water and nutrients to the Gulf of Mexico; to define subbasins that are the most important contributors of nutrients to the gulf; and to investigate the relations among streamflow, nutrient fluxes, and the size and duration of the Gulf of Mexico hypoxic zone. A comparative analysis between the baseline period of 1980-1996 and 5-year moving averages thereafter indicate that the average annual streamflow and fluxes of total nitrogen, nitrate, orthophosphate, and silica to the Gulf of Mexico have decreased. However, the flux of total phosphorus between the baseline period and subsequent 5-year periods has increased. The average spring (April, May, and June) streamflow and fluxes of silica, total nitrogen, nitrate, and orthophosphate to the Gulf of Mexico also decreased, whereas the spring flux of total phosphorus has increased. Similar changes in streamflow and nutrient flux were observed at many sites Buxtonwithin the basin. The inputs of water, total nitrogen, and total phosphorus from the major subbasins of the Mississippi-Atchafalaya River Basin as a percentage of the to-the-gulf totals have increased from the Ohio River Basin, decreased from the Missouri River Basin, and remained relatively unchanged from the Upper Mississippi, Red, and Arkansas River Basins. Changes in streamflow and nutrient fluxes are related, but short-term variations in sources of streamflow and nutrients complicate the interpretation of factors that affect nutrient delivery to the Gulf of Mexico. Parametric time-series models are used to try and separate natural variability in nutrient flux from changes due to other causes. Results indicate that the decrease in annual nutrient fluxes that has occurred between the 1980-1996 baseline period and more recent years can be largely attributed to natural causes (climate and streamflow) and not management actions or other human controlled activities in the Mississippi-Atchafalaya River Basin. The downward trends in total nitrogen, nitrate, ammonium, and orthophosphate that were detected at either the Mississippi River near St. Francisville, La., or the Atchafalaya River at Melville, La., occurred prior to 1995. In spite of the general decrease in nutrient flux, the average size of the Gulf of Mexico hypoxic zone has increased between 1997 and 2007. The reasons for this are not clear but could be due to the type or nature of nutrient delivery. Whereas the annual flux of total nitrogen to the Gulf of Mexico has decreased, the proporti

Scientific Investigations Report↗
USGS2015

California State Waters Map Series — Offshore of Point Reyes, California

This publication about the Offshore of Point Reyes map area includes ten map sheets that contain explanatory text, in addition to this descriptive pamphlet and a data catalog of geographic information system (GIS) files. Sheets 1, 2, and 3 combine data from four different sonar surveys to generate comprehensive high-resolution bathymetry and acoustic-backscatter coverage of the map area. These data reveal a range of physiographic features (highlighted in the perspective views on sheet 4) such as the flat, sediment-covered seafloor in Drakes Bay, as well as abundant “scour depressions” on the Bodega Head–Tomales Point shelf (see sheet 9) and local, tectonically controlled bedrock uplifts. To validate geological and biological interpretations of the sonar data shown in sheets 1, 2, and 3, the U.S. Geological Survey towed a camera sled over specific offshore locations, collecting both video and photographic imagery; these “ground-truth” surveying data are summarized on sheet 6. Sheet 5 is a “seafloor character” map, which classifies the seafloor on the basis of depth, slope, rugosity (ruggedness), and backscatter intensity and which is further informed by the ground-truth-survey imagery. Sheet 7 is a map of “potential habitats,” which are delineated on the basis of substrate type, geomorphology, seafloor process, or other attributes that may provide a habitat for a specific species or assemblage of organisms. Sheet 8 compiles representative seismic-reflection profiles from the map area, providing information on the subsurface stratigraphy and structure of the map area. Sheet 9 shows the distribution and thickness of young sediment (deposited over the last about 21,000 years, during the most recent sea-level rise) in both the map area and the larger Salt Point to Drakes Bay region, interpreted on the basis of the seismic-reflection data, and it identifies the Offshore of Point Reyes map area as lying within the Bodega Head–Tomales Point shelf, Point Reyes bar, and Bolinas shelf domains. Sheet 10 is a geologic map that merges onshore geologic mapping (compiled from existing maps by the California Geological Survey) and new offshore geologic mapping that is based on integration of high-resolution bathymetry and backscatter imagery (sheets 1, 2, 3), seafloor-sediment and rock samples (Reid and others, 2006), digital camera and video imagery (sheet 6), and high-resolution seismic-reflection profiles (sheet 8), as well as aerial-photographic interpretation of nearshore areas. The information provided by the map sheets, pamphlet, and data catalog have a broad range of applications. High-resolution bathymetry, acoustic backscatter, ground-truth-surveying imagery, and habitat mapping all contribute to habitat characterization and ecosystem-based management by providing essential data for delineation of marine protected areas and ecosystem restoration. Many of the maps provide high-resolution baselines that will be critical for monitoring environmental change associated with climate change, coastal development, or other forcings. High-resolution bathymetry is a critical component for modeling coastal flooding caused by storms and tsunamis, as well as inundation associated with longer term sea-level rise. Seismic-reflection and bathymetric data help characterize earthquake and tsunami sources, critical for natural-hazard assessments of coastal zones. Information on sediment distribution and thickness is essential to the understanding of local and regional sediment transport, as well as the development of regional sediment-management plans. In addition, siting of any new offshore infrastructure (for example, pipelines, cables, or renewable-energy facilities) will depend on high-resolution mapping. Finally, this mapping will both stimulate and enable new scientific research and also raise public awareness of, and education about, coastal environments and issues.

California↗
USGS2005

Compilation of geologic, hydrologic, and ground-water flow modeling information for the Spokane Valley-Rathdrum Prairie aquifer, Spokane County, Washington, and Bonner and Kootenai Counties, Idaho

The U.S. Geological Survey, in cooperation with the Idaho Department of Water Resources and Washington Department of Ecology compiled and described geologic, hydrologic, and ground-water flow modeling information about the Spokane Valley-Rathdrum Prairie (SVRP) aquifer in northern Idaho and northeastern Washington. Descriptions of the hydrogeologic framework, water-budget components, ground- and surface-water interactions, computer flow models, and further data needs are provided. The SVRP aquifer, which covers about 370 square miles including the Rathdrum Prairie, Idaho and the Spokane valley and Hillyard Trough, Washington, was designated a Sole Source Aquifer by the U.S. Environmental Protection Agency in 1978. Continued growth, water management issues, and potential effects on water availability and water quality in the aquifer and in the Spokane and Little Spokane Rivers have illustrated the need to better understand and manage the region's water resources. The SVRP aquifer is composed of sand, gravel, cobbles, and boulders primarily deposited by a series of catastrophic glacial outburst floods from ancient Glacial Lake Missoula. The material deposited in this high-energy environment is coarser-grained than is typical for most basin-fill deposits, resulting in an unusually productive aquifer with well yields as high as 40,000 gallons per minute. In most places, the aquifer is bounded laterally by bedrock composed of granite, metasedimentary rocks, or basalt. The lower boundary of the aquifer is largely unknown except along the margins or in shallower parts of the aquifer where wells have penetrated its entire thickness and reached bedrock or silt and clay deposits. Based on surface geophysics, the thickness of the aquifer is about 500 ft near the Washington-Idaho state line, but more than 600 feet within the Rathdrum Prairie and more than 700 feet in the Hillyard trough based on drilling records. Depth to water in the aquifer is greatest in the northern Rathdrum Prairie (about 500 feet) and least near the city of Spokane along the Spokane River (less than about 50 feet). Ground-water flow is south from near the southern end of Lake Pend Oreille and Hoodoo Valley, through the Rathdrum Prairie, then west toward Spokane. In Spokane, the aquifer splits and water moves north through the Hillyard Trough as well as west through the Trinity Trough. From the Trinity Trough water flows north along the western arm of the aquifer. The aquifer's discharge area is along the Little Spokane River and near Long Lake, Washington. A compilation of estimates of water-budget components, including recharge (precipitation, irrigation, canal leakage, septic tank effluent, inflow from tributary basins, and flow from the Spokane River) and discharge (withdrawals from wells, flow to the Spokane and Little Spokane Rivers, evapotranspiration, and underflow to Long Lake) illustrates that these estimated values should be compared with caution due to several variables including the area and time period of interest as well as methods employed in making the estimates. Numerous studies have documented the dynamic ground-water and surface-water interaction between the SVRP aquifer and the Spokane and Little Spokane Rivers. Gains and losses vary throughout the year, as well as the locations of gains and losses. September 2004 streamflow measurements indicated that the upper reach of the Spokane River between Post Falls and downstream at Flora Road lost 321 cubic feet per second. A gain of 736 cubic feet per second was measured between the Flora Road site and downstream at Green Street Bridge. A loss of 124 cubic feet per second was measured for the reach between the Green Street Bridge and the Spokane River at Spokane gaging station. The river gained about 87 cubic feet per second between the Spokane River at Spokane gaging station and the TJ Meenach Bridge. Overall, the Spokane River gained about 284 cubic feet per second between the Post Falls,

Scientific Investigations Report↗
USGS2006

Physical habitat classification and instream flow modeling to determine habitat availability during low-flow periods, North Fork Shenandoah River, Virginia

Increasing development and increasing water withdrawals for public, industrial, and agricultural water supply threaten to reduce streamflows in the Shenandoah River basin in Virginia. Water managers need more information to balance human water-supply needs with the daily streamflows necessary for maintaining the aquatic ecosystems. To meet the need for comprehensive information on hydrology, water supply, and instream-flow requirements of the Shenandoah River basin, the U.S. Geological Survey and the Northern Shenandoah Valley Regional Commission conducted a cooperative investigation of habitat availability during low-flow periods on the North Fork Shenandoah River. Historic streamflow data and empirical data on physical habitat, river hydraulics, fish community structure, and recreation were used to develop a physical habitat simulation model. Hydraulic measurements were made during low, medium, and high flows in six reaches at a total of 36 transects that included riffles, runs, and pools, and that had a variety of substrates and cover types. Habitat suitability criteria for fish were developed from detailed fish-community sampling and microhabitat observations. Fish were grouped into four guilds of species and life stages with similar habitat requirements. Simulated habitat was considered in the context of seasonal flow regimes to show the availability of flows that sustain suitable habitat during months when precipitation and streamflow are scarce. The North Fork Shenandoah River basin was divided into three management sections for analysis purposes: the upper section, middle section, and lower section. The months of July, August, and September were chosen to represent a low-flow period in the basin with low mean monthly flows, low precipitation, high temperatures, and high water withdrawals. Exceedance flows calculated from the combined data from these three months describe low-flow periods on the North Fork Shenandoah River. Long-term records from three streamflow-gaging stations were used to characterize the flow regime: North Fork Shenandoah River at Cootes Store, Va. (1925-2002), North Fork Shenandoah River at Mount Jackson, Va. (1943-2002), and North Fork Shenandoah River near Strasburg, Va. (1925-2002). The predominant mesohabitat types (14 percent riffle, 67.3 percent run, and 18.7 percent pool) were classified along the entire river (100 miles) to assist in the selection of reaches for hydraulic and fish community data collection. The upper section has predominantly particle substrate, ranging in size from sand to boulders, and the shortest habitat units. The middle section is a transitional section with increased bedrock substrate and habitat unit length. The lower section has predominantly bedrock substrate and the longest habitat units in the river. The model simulations show that weighted usable-habitat area in the upper management section is highest at flows higher than the 25-percent exceedance flow for July, August, and September. During these three months, total weighted usable-habitat area in this section is often less than the simulated maximum weighted usable-habitat area. Habitat area in the middle management section is highest at flows between the 25- and 75-percent exceedance flows for July, August, and September. In the middle section during these months, both the actual weighted usable-habitat area and the simulated maximum weighted usable-habitat area are associated with this flow range. Weighted usable-habitat area in the lower management section is highest at flows lower than the 75-percent exceedance flow for July, August, and September. In the lower section during these three months, some weighted usable-habitat area is available, but the normal range of flows does not include the simulated maximum weighted usable-habitat area. A time-series habitat analysis associated with the historic streamflow, zero water withdrawals, and doubled water withdrawals was completed. During s

Scientific Investigations Report↗
USGS2016

Construction, calibration, and validation of the RBM10 water temperature model for the Trinity River, northern California

We constructed a one-dimensional daily averaged water-temperature model to simulate Trinity River temperatures for 1980–2013. The purpose of this model is to assess effects of water-management actions on water temperature and to provide water temperature inputs for a salmon population dynamics model. Simulated meteorological data, observed streamflow data, and observed water temperatures were used as model inputs to simulate a continuous 34-year time series of historical daily mean water temperature at eight locations along 112.2 river miles from Lewiston Dam near Weaverville, California, downstream to the Klamath River confluence. To demonstrate the utility of the model to inform management actions, we simulated three management alternatives to assess the effects of bypass flow augmentation in a drought year, 1994, and compared those results to the simulated historical baseline, referred to as the “No Action” alternative scenario. Augmentation flows from the Lewiston Dam bypass consist of temperature-controlled releases capable of cooling downstream water temperatures in hot times of the year, which can reduce the probability of disease outbreaks in fish populations. Outputs from the Trinity River water-temperature model were then used as inputs to an existing water-temperature model of the Klamath River to evaluate the effect of augmentation flow releases on water temperatures in the lower Klamath River. We structured the Trinity River water-temperature model in River Basin Model-10 (RBM10), which uses a simple equilibrium flow model, assuming discharge in each river segment on each day is transmitted downstream instantaneously. The model uses a heat-budget formulation to quantify heat flux at the air-water interface. Inputs for the heat budget are calculated from daily mean meteorological data, including net shortwave solar radiation, net longwave atmospheric radiation, air temperature, wind speed, vapor pressure, and a psychrometric constant needed to calculate the Bowen ratio. The modeling domain was divided into eight reaches ranging in length from 8.8 to 20.6 miles, which were calibrated and validated separately with observed water temperature data collected irregularly from 1980 to 2013. Root mean square errors of observed and simulated water temperatures for the eight reaches ranged from 0.25 to 1.12 degrees Celsius (°C). Mean absolute errors ranged from 0.18 to 0.89 °C. For model validation, a k -fold cross-validation technique was used. Validation root mean square error and mean absolute error for the eight reaches ranged from 0.24 to 1.11 °C and from 0.18 to 0.89 °C, respectively. Augmentation scenarios were based on historical hydrological and meteorological data, combined with prescribed flow and temperature releases from Lewiston Dam provided by the Bureau of Reclamation. Water releases were scheduled to achieve targeted flows of 2,500, 2,800, and 3,200 cubic feet per second in the lower Klamath River from mid-August through late September, coinciding with the upstream migration of adult fall-run Chinook salmon ( Oncorhynchus tshawytscha ). Water temperatures simulated at river mile 5.7 on the Klamath River showed a 5 °C decrease from the No Action historical baseline, which was near or greater than 23 °C when augmentation began in mid-August. Thereafter, an approximate 1 °C difference among augmentation scenarios emerged, with the decrease in water temperature commensurate to the level of augmentation. All augmentation scenarios simulated water temperatures equal to or less than 21 °C from mid-August through late September. Water temperatures equal to or greater than 23 °C are of particular interest because of a thermal threshold known to inhibit upstream migration of salmon. When temperatures exceed this approximate 23 °C threshold, Chinook salmon are known to congregate in high densities in thermal refugias and show extended residence times, which can potentially trigger epizootic outbreaks such as of Ichthyophthirius multifiliis (“Ich”) and Flavobacterium columnare (“Columnaris”) that were the causative factors of the Klamath River fish kill in 2002. A model with the ability to simulate water temperatures in response to management actions at the basin scale is a valuable asset for water managers who must make decisions about how best to use limited water resources, which directly affect the state of fisheries in the Klamath Basin.

California↗
USGS2011

Groundwater quality of the Gulf Coast aquifer system, Houston, Texas, 2010

During March–December 2010, the U.S. Geological Survey, in cooperation with the city of Houston, collected source-water samples from 60 municipal supply wells in the Houston area. These data were collected as part of an ongoing study to determine concentrations, spatial extent, and associated geochemical conditions that might be conducive for mobility and transport of selected naturally occurring contaminants (selected trace elements and radionuclides) in the Gulf Coast aquifer system in the Houston area. In the summers of 2007 and 2008, a reconnaissance-level survey of these constituents in untreated water from 28 municipal supply wells was completed in the Houston area. Included in this report are the complete analytical results for 47 of the 60 samples collected in 2010—those results which were received from the laboratories and reviewed by the authors as of December 31, 2010. All of the wells sampled were screened in the Gulf Coast aquifer system; 22 were screened entirely in the Evangeline aquifer, and the remaining 25 wells contained screened intervals that intersected both Evangeline and Chicot aquifers. The data documented in this report were collected as part of an ongoing study to characterize source-water-quality conditions in untreated groundwater prior to drinking-water treatment. An evaluation of contaminant occurrence in source water provides background information regarding the presence of a contaminant in the environment. Because source-water samples were collected prior to any treatment or blending that potentially could alter contaminant concentrations, the water-quality results documented by this report represent the quality of the source water, not the quality of finished drinking water provided to the public. Samples were analyzed for major ions (calcium, magnesium, potassium, sodium, bromide, chloride, fluoride, silica, and sulfate), residue on evaporation (dissolved solids), trace elements (arsenic, barium, boron, chromium, iron, lithium, manganese, molybdenum, selenium, strontium, and vanadium), and selected radionuclides (gross alpha- and beta-particle activity [at 72 hours and 30 days], carbon-14, radium-226, radon-222, and uranium). Field measurements were made of selected physicochemical (relating to both physical and chemical) properties (oxidation-reduction potential, turbidity, dissolved-oxygen concentration, pH, specific conductance, water temperature, and alkalinity) and unfiltered sulfides. Similar to the results from the reconnaissance survey, physicochemical properties, major ions, and trace elements varied considerably. The ranges of selected physicochemical properties were as follows: oxidation-reduction potential ranged from -173 to 466 millivolts, dissolved oxygen ranged from less than 0.1 to 4.4 milligrams per liter, pH ranged from 7.2 to 7.8, specific conductance ranged from 439 to 724 microsiemens per centimeter at 25 degrees Celsius, and alkalinity ranged from 159 to 276 milligrams per liter as calcium carbonate. The largest ranges in concentration for filtered major ion constituents were obtained for cations sodium and calcium and for anions chloride and sulfate. Arsenic concentrations measured in samples from the 47 wells ranged from 1.6 to 23.5 micrograms per liter. The maximum concentration of arsenic (23.5 micrograms per liter) was measured in the source-water sample from well LJ-65-12-328. Quantifiable concentrations of barium, boron, lithium, molybdenum, and strontium were measured in all 47 filtered, source-water samples. Quantifiable concentrations of manganese were measured in 46 source-water samples, and an estimated concentration of manganese was measured in 1 sample. Chromium, iron, selenium, and vanadium were detected in 24 or more of the 47 source-water samples. Gross alpha-particle activities and beta-particle activities for all 47 samples were analyzed at 72 hours after sample collection and again at 30 days after sample collection, allowing for the measurement of the activity of short-lived isotopes. Gross alpha-particle activities reported in this report were not adjusted for activity contributions by radon or uranium and, therefore, are conservatively high estimates if compared to the U.S. Environmental Protection Agency National Primary Drinking Water Regulation for adjusted gross alpha-particle activity. The gross alpha-particle activities at 30 days in the samples ranged from R0.60 to 25.5 picocuries per liter and at 72 hours ranged from 2.58 to 39.7 picocuries per liter, and the "R" preceding the value of 0.60 picocuries per liter refers to a nondetected result less than the sample-specific critical level. Gross beta-particle activities measured at 30 days ranged from 1.17 to 14.4 picocuries per liter and at 72 hours ranged from 1.97 to 4.4 picocuries per liter. Filtered uranium was detected in quantifiable amounts in all of the 47 wells sampled. The uranium concentrations ranged from 0.03 to 42.7 micrograms per liter. One sample was analyzed for carbon-14, and the amount of modern atmospheric carbon was reported as 0.2 percent. Six source-water samples collected from municipal supply wells were analyzed for radium-226, and all of the concentrations were considered detectable concentrations (greater than their associated sample-specific critical level). Three source-water samples collected were analyzed for radon-222, and all of the concentrations were substantially greater than the associated sample-specific critical level.

Texas↗