SEARCH · USGS Science

Results for “Science of the Total Envionrment”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,687 records · Page 44Linked to original sources

USGS1994

Hydrogeologic atlas of aquifers in Indiana

Aquifers in 12 water-management basins of Indiana are identified in a series of 104 hydrogeologic sections and 12 maps that show the thickness and configuration of aquifers. The vertical distribution of water-bearing units and a generalized potentiometric profile are shown along 3,500 miles of section lines that were constructed from drillers' logs of more than 4,200 wells. The horizontal scale of the sections is 1:125,000. Maps of aquifers showing the areal distribution of each aquifer type were drawn at a scale of 1:500,000. Unconsolidated aquifers are the most widely used aquifers in Indiana and include surficial, buried, and discontinuous layers of sand and gravel. Most of the surficial sand and gravel is in large outwash plains in northern Indiana and along the major rivers. Buried sand and gravel aquifers are interbedded with till deposits in much of the northern two-thirds of Indiana. Discontinuous sand and gravel deposits are present as isolated lenses, primarily in glaciated areas. The bedrock aquifers generally have lower yields than most of the sand and gravel aquifers; however, bedrock aquifers are areally widespread and are an important source of water. Bedrock aquifer types consist of carbonates; sandstones; complexly interbedded sandstones, siltstones, shales, limestones, and coals; and an upper weathered zone in low permeability rock. Carbonate aquifers underlie about one-half of Indiana and are the most productive of the bedrock aquifers. The other principal bedrock aquifer type, sandstone, underlies large areas in the southwestern one-fifth of Indiana. No aquifer is known to be present in the southeastern corner of Indiana.

Water-Resources Investigations Report↗

USGS2025

Fluid inclusion constraints on the geometry of the magmatic plumbing system beneath Mauna Loa – Part 2: Xenoliths

Mauna Loa volcano erupts crystal-poor material at its summit and more crystal-rich material on its rift zones. Some of the more olivine-rich lava flows contain xenoliths with diverse mineralogy, including cumulate harzburgites with high-Mg# orthopyroxenes and high-Fo olivines (both > 84). Previous experimental work and thermodynamic modelling has proposed that high-Mg# orthopyroxenes only crystallize from Mauna Loa melts at high pressures (> 6 kbar, > 20 km), leading to suggestions that there is a region of sub-Moho magma storage at Mauna Loa in addition to the geophysically imaged magma reservoir at 2–5 km depth below the summit. We use melt and fluid inclusion barometry combined with thermodynamic models to further investigate this suggestion. Fluid inclusion data from harzburgites and dunitic xenoliths yield storage depths remarkably similar to those found in non-xenolithic crystals from lavas and tephras, with a clear peak at ~ 2–3 km (below the summit). Depths from melt inclusions in these xenoliths overlap with fluid inclusion pressures, ruling out the possibility of fluid inclusion re-equilibration during a period of stalling in a shallower reservoir. We examine five different thermodynamic models and find that the minimum pressure of olivine-orthopyroxene co-saturation varies by ~ 4 kbar (~ 12 km). These models also fail to predict that orthopyroxene is stable in ~ 15–80% of compositionally relevant experimental charges which grew orthopyroxene. Overall, this shows that phase stability modelling is an unreliable method of determining magma storage depth at Mauna Loa. We suggest that model discrepancies reflect a lack of experimental constraints on orthopyroxene stability at > 1200 ℃ and 0.01–5 kbar. Based on the presence of large oikocrystic orthopyroxenes completely enclosing rounded olivine chadacrysts, we suggest that these harzburgitic xenoliths formed through the reaction of intruding melts with olivine mush piles within the Mauna Loa edifice at ~ 3 km depth below the summit, with no need for a deeper storage reservoir. The predominance of pre-eruptive shallow storage means that there is more chance of detecting reservoir destabilization with geophysical monitoring techniques compared to a scenario where melts are supplied from sub-Moho reservoirs.

Hawaii↗

USGS2022

U-Pb scheelite ages of tungsten and antimony mineralization in the Stibnite-Yellow Pine district, central Idaho

The Stibnite-Yellow Pine district contains the largest antimony resource in the United States, as well as significant gold, and is a historic producer of tungsten. Application of in situ laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) direct dating of scheelite from two Au-Sb-W ore deposits, Yellow Pine and Hangar Flats, yielded an older group of U-Pb ages in the range of 60.0 ± 2.8 to 57.0 ± 1.1 Ma and a younger U-Pb age for scheelite intergrown with stibnite of 47.4 ± 1.1 Ma. These in situ analyses were calibrated by isotope dilution-thermal ionization mass spectrometry (ID-TIMS) U-Pb lower intercept ages of two coarsely crystalline scheelite samples that yielded ages of 57.52 ± 0.22 and 56.62 ± 0.16 Ma. Scheelite of the latter age is of sufficient quality to serve as a primary reference material for LA-ICP-MS scheelite U-Pb geochronology. The group of older U-Pb scheelite ages agrees with 40 Ar/ 39 Ar ages of 56.9 ± 1.2 to 56.38 ± 0.54 Ma on adularia from Yellow Pine and Hangar Flats, whereas the younger U-Pb scheelite age is similar to an 40 Ar/ 39 Ar age of 46.00 ± 0.40 Ma on adularia from an epithermal gold-silver deposit in the adjacent Thunder Mountain caldera. Our results indicate that the main stage of tungsten mineralization occurred at ca. 57 Ma, whereas the main stage of antimony mineralization occurred at ca. 47 Ma—thereby providing first-time age constraints for antimony and tungsten mineralization in the Stibnite-Yellow Pine district.

Idaho↗

USGS1999

Water-quality assessment of the New England coastal basins in Maine, Massachusetts, New Hampshire, and Rhode Island: Environmental settings and implications for water quality and aquatic biota

The New England Coastal Basins in Maine, Massachusetts, New Hampshire, and Rhode Island constitute one of 59 study units selected for water-quality assessment as part of the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) program. England Coastal Basins study unit encompasses the fresh surface waters and ground waters in a 23,000 square-mile area that drains to the Atlantic Ocean. Major basins include those of the Kennebec, Androscoggin, Saco, Merrimack, Charles, Blackstone, Taunton, and Pawcatuck Rivers. Defining the environmental setting of the study unit is the first step in designing and conducting a multi-disciplinary regional water-quality assessment. The report describes the natural and human factors that affect water quality in the basins and includes descriptions of the physiography, climate, geology, soils, surface- and ground-water hydrology, land use, and the aquatic ecosystem. Although surface-water quality has greatly improved over the past 30 years as a result of improved wastewater treatment at municipal and industrial wastewater facilities, a number of water-quality problems remain. Industrial and municipal wastewater discharges, combined sewer overflows, hydrologic modifications from dams and water diversions, and runoff from urban land use are the major causes of water-quality degradation in 1998. The most frequently detected contaminants in ground water in the study area are volatile organic compounds, petroleum-related products, nitrates, and chloride and sodium. Sources of these contaminants include leaking storage tanks, accidental spills, landfills, road salting, and septic systems and lagoons. Elevated concentrations of mercury are found in fish tissue from streams and lakes throughout the study area.

Maine, Massachusetts, New Hampshire, Rhode Island↗

USGS2025

Uppermost Oligocene and Miocene diatom biostratigraphy of Ocean Drilling Program Sites 682 and 688 from the Peru Margin

The diatom biochronology of ODP (Ocean Drilling Program) Holes 682A and 688E provides a detailed framework for refiningMiocene diatom zonation in the East Pisco Basin of southern Peru, establishing both a nearly complete offshore reference section and a correlation tool for the fragmentary onshore vertebrate-bearing deposits. This new biostratigraphic record documents a complete succession of low latitude and/or northeastern Pacific Miocene diatom zones, with two notable exceptions: a dissolution and/or hiatus interval (*16.5–14 Ma) during the Middle Miocene Climatic Optimum and a likely earliest Miocene hiatus (*23.4–21.8 Ma). Although eastern equatorial Pacific diatom zones characterize the Upper Oligocene and Lower Miocene strata, an increased abundance of cool-water diatoms that lived during the Middle and Late Miocene allows better application of northeast Pacific diatom zones, except during the Messinian (7–6 Ma) when warm-water diatoms predominate. The effects of eustatic sea level and tectonics on depositional sequences in the EPB and in offshore cores off central Peru are discussed.

Stratigraphy↗

USGS2026

Groundwater source water assessment area delineation of public supply wells in the Treasure Valley, western Idaho

The Idaho Department of Environmental Quality (IDEQ) is responsible for assessing the source water for public water supply systems including the delineation of source water assessment areas for wells, which are defined as the subsurface areas contributing water to a well during a period of time. Part of the IDEQ assessment plan is to update source water assessments over time. The U.S. Geological Survey (USGS) developed a new groundwater-flow model for part of the western Snake River Plain aquifer in southwestern Idaho. This groundwater- flow model provided a new opportunity for IDEQ to update source water assessment for public water supply wells within the model boundary. The USGS, in cooperation with IDEQ, used the USGS Treasure Valley Groundwater Flow Model along with a MODPATH particle tracking post-processing program to reassess public-water supply source water assessment areas. The USGS created an automated script that requests a well location, depth, and pumpage rate, and then incorporates that information into the Treasure Valley Groundwater Flow Model combined with the MODPATH model to create 3-, 6-, and 10-year time of travel zones that are output to a geographic information system shapefile. The TVSWA_Delineator script provides a fast, transparent tool for IDEQ to reassess or create new public-water supply source water assessment area delineations based on new and updated information and is available as a Python script and a Windows executable with the compiled script and all necessary components. TVSWA_Delineator utilizes a quadtree approach to rediscretize the Treasure Valley Groundwater Flow Model grid around the pumping well location from 1-mile cell lengths telescoped down to 1/16 mile. This rediscretization increases the source water assessment area delineation resolution near the pumping well and minimizes the effect of weak sinks in the MODPATH model. The stress inputs for each month of the final 10 years (2006 to 2015) of the Treasure Valley Groundwater Flow model historical simulation were averaged for the particle tracking analysis. The MODPATH model used backwards tracking of particles released at each stress period to create the source water assessment area delineations. This report documents the creation of the TVSWA_Delineator Python script, including adaptations made to the Treasure Valley Groundwater Flow Model, creation of a companion MODPATH model, and post-processing results to provide source water assessment areas.

Idaho↗

USGS2024

Utilization of stochastic ground motion simulations for scenario-based performance assessment of geo-structures

Probabilistic seismic performance assessments of engineered structures can be highly sensitive to the seismic input excitation and its variability. In the present study, the scenario-based performance assessment recommended by Federal Emergency Management Agency (FEMA) P-58 guidelines is adopted to estimate seismic fragility of concrete dams for various seismic hazard scenarios. Due to the scarcity of recorded ground motions and thereby their poor representation of uncertainties, stochastic ground motion simulation methods are utilized to obtain the required input excitations. Moreover, to understand the uncertainty in ground motion simulation models, two broadband stochastic simulation models are used to generate input excitations representing six seismic hazard scenarios defined by earthquake magnitude, source-to-site distance, and soil conditions. Optimal intensity measure parameters for each scenario are identified using a systematic procedure that considers criteria such as efficiency, practicality, proficiency, sufficiency, and hazard compatibility. Fragility curves and surfaces are derived using the cloud analysis technique, taking into account various damage measures and limit state functions. The study finds that the derived fragility curves are particularly sensitive to the selection of earthquake scenarios, the choice of records, and the methods used to calculate fragility curves, with less sensitivity observed to different engineering demand parameters. Given this sensitivity, particularly to ground motion selection, the study highlights the necessity of incorporating both model-to-model variability (epistemic uncertainty) and record-to-record variability (aleatory uncertainty), alongside the established material and modeling uncertainties, in the probabilistic seismic assessment.

Reliability Engineering and System Safety (RESS)↗

USGS2026

Evolution of arsenic speciation during thermal treatment simulating wildfire heating in arsenic-rich sediments

Understanding arsenic transformations during wildfires can help better constrain the environmental impacts of increased wildfire intensity, frequency, and burned area. Previous studies have monitored the evolution of metal(loid) speciation at specific time/temperature endpoints, hampering the comprehension of the dynamic transformations of metal(loid)s during wildfires. Here, a novel approach, namely in situ time-resolved X-ray absorption near edge structure (TR-XANES) spectroscopy, was used for the first time to monitor the heat-induced redox transformations of arsenic (As) in two As-rich sediments with different characteristics. No arsenic transformations were observed in either sediment at room temperature or when the sediments were heated to a maximum temperature of 400 ºC. When heated to a maximum temperature of 600 or 700 ºC, As underwent complex, dynamic, and partially reversible redox transformations, the extent of which varied with sediment properties, initial As speciation, and heating temperature and duration. In the case of sediments initially containing As(V) and a low sulfide/sulfate ratio, the As(V) was reduced to As(III) over a short period of time, followed by immediate reoxidation of As(III) to As(V). The extent of the transient As reduction increased with increasing maximum temperature. The final As speciation at the end of the heating experiment was not substantially different from that at the beginning of the experiment. In contrast, in sediments that were best described by a more complex combination of reference compounds (As(V) coprecipitated with or adsorbed on iron oxide, arseniosiderite, arsenopyrite) with a high sulfide/sulfate ratio, As(V) phases were reduced to As(III) and As(III) was further reduced to As(-I) (at 700 ºC, only), followed by delayed reoxidation of As(-I) to As(III) (at 700 ºC, only) and reoxidation of As(III) to As(V). Approximately 9% and 26% of all As remained as As(III) ( i.e., was not reoxidized to As(V)) at the end of the experiment when heated to a maximum temperature of 600 and 700 ºC, respectively, which is higher than the relative abundance of As(III) in the native sediment. These fire-induced As transformations can potentially enhance As mobilization to surface water and groundwater, posing risks to environmental and human health.

California↗

USGS2025

Migration of seismicity from the mantle to the upper crust beneath Harrat Lunayyir volcanic field, Saudi Arabia

Harrat Lunayyir is a volcanic field in Saudi Arabia that experienced a Mw~5.4 earthquake driven by an upper-crustal dike intrusion in May 2009. This volcanic field has exhibited numerous forms of volcanic seismicity both prior to and since the 2009 dike intrusion. Significantly, earthquakes within the lithospheric mantle and, rarely, the lower crust are present in the two-decade long seismicity catalog of Harrat Lunayyir. Here we analyze 24 years of volcanic seismicity at Harrat Lunayyir from 1998 to 2022. We find that: 1) precursory seismicity began at least eight years prior to the 2009 event, with a particularly notable seismic episode one year prior; 2) lithospheric mantle seismicity is highly localized in space and in time, largely occurring in discrete sequences lasting on the order of a few hours to a few days; 3) one seismic sequence clearly migrates upward from the lithospheric mantle to the upper crust, including seismicity within the nominally ductile lower crust; 4) crustal seismicity has been slowly declining over time; and 5) lithospheric-mantle seismicity does not show any apparent decline with time. From these observations we infer that the seismicity is driven by magmatic fluids or volatiles, and seismic monitoring of this volcanic field should continue into the future.

Harrat Lunayyir volcanic field↗

USGS2025

Groundwater hydrology, groundwater and surface-water interactions, water quality, and groundwater-flow simulations for the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado, 2017–19

In 2017, the U.S. Geological Survey, in cooperation with the Upper Arkansas Water Conservancy District, began a study to provide a comprehensive analysis of the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado. The study included collection of data pertaining to groundwater hydrology, groundwater and surface-water interactions, and water quality in the alluvial aquifer. In addition to providing foundational information on the hydrology of the alluvial aquifer, a numerical groundwater-flow model was developed to estimate the potential effects of additional storage of groundwater in the alluvial aquifer. Groundwater-level elevation data from 30 wells were used to estimate groundwater-flow directions in the alluvial aquifer, which were generally from the southwest to northeast, away from the Sangre de Cristo Mountains and towards perennial streams in the center of the valley. Although some seasonal variation was apparent in groundwater-level elevation records, no statistically significant seasonal trends were indicated. Statistically significant long-term trends were indicated in groundwater-level elevation records for 8 of the 30 wells, and of these wells with statistically significant trends, all but 1 indicated a negative trend of groundwater-level elevations. Spatial evaluation of wells with statistically significant negative groundwater-level elevation trends showed many are in areas of denser well drilling for domestic or other uses, indicating increasing groundwater use could potentially be causing groundwater-level elevation declines. There were instances of wells with no statistically significant groundwater-level elevation trends also located in areas of greater density of well completions. Additional investigations may be necessary to more fully characterize the processes responsible for negative groundwater-level elevation trends. Streamflow gain or loss calculations were completed for low flow in 2017–19 and for high flow in 2018 in nine reaches of streams within the study area. Stream reaches of the upper Texas Creek, upper Grape Creek, upper-middle Grape Creek, and Taylor Creek displayed consistent streamflow loss in each period from 2017 to 2019. These stream reaches represent long-term sources of recharge to the alluvial aquifer. Streamflow gain or loss varies through time in other stream reaches (lower Texas Creek, lower-middle Grape Creek, lower Grape Creek below Westcliffe, and lower Grape Creek above DeWeese Reservoir). The temporally variable behavior indicates these stream reaches may be sources of groundwater recharge or areas of groundwater discharge, likely depending on temporal dynamics between the elevation of the water table and the stream. Water-quality samples were collected from 10 groundwater wells and 10 stream sites during September through November 2019. All groundwater and stream samples were analyzed for major and trace elements and stable isotopes of water. A subset of groundwater samples was also analyzed for the environmental tracers sulfur hexafluoride, tritium, and noble gases. Comparison of water-quality results to U.S. Environmental Protection Agency drinking water-quality standards indicated no constituents exceeded primary standards for human health. Spatial evaluation of water quality indicated the concentrations of various constituents are likely controlled by groundwater and surface-water interactions and by spatial variability in bedrock geology underlying the alluvial aquifer. Specifically, streams shown to gain from groundwater had water chemistry constituent compositions similar to groundwater, whereas streams exiting the Sangre de Cristo Mountains tended to have compositions consistent with snowmelt. Groundwater geochemistry appeared to be partially controlled by oxidation-reduction processes and by proximity to igneous rocks in the Wet Mountains. Environmental tracers used to estimate groundwater age indicated all sampled groundwater contained tracers representing modern recharge (approximately less than 65 years old) but mixing of premodern recharge (approximately more than 65 years old) also occurs. Spatial evaluation of environmental tracers indicated large faults may be conduits for upwelling of older groundwater. No trends were observed in groundwater age with well depth, indicating all sampled wells are located within the zone of active groundwater flow. The presence of modern groundwater in wells with statistically significant negative groundwater-level elevation trends indicates groundwater storage depletions may be partially offset by capture of modern recharge. Repeated sampling of groundwater age would be necessary, however, to determine if any trends in groundwater age exist, which may indicate changing groundwater recharge, storage, or discharge. Additional investigations could also consider quantifying groundwater age in deeper wells to more fully define the depth of active groundwater flow. A numerical groundwater-flow model was developed to estimate components of the water budget, simulate groundwater and surface-water interactions, and evaluate the potential effects of aquifer storage and recovery. Simulated groundwater-level elevations from the calibrated groundwater-flow model are similar to the observed pattern of groundwater-level elevations with higher elevations in the western part of the study area along the Sangre de Cristo Mountains. Simulated water-budget components indicate most of the recharge to the alluvial aquifer is derived from streamflow losses, which is consistent with observations of losing streams along the mountain front. The largest groundwater discharge component of the alluvial aquifer was to streams in the center of the valley, where observations of stream gain or loss indicated the predominance of gaining conditions. Comparison of groundwater and surface-water interactions between the calibrated groundwater-flow model for 2000-19 (the base-case model) and a simulation including additional recharge, representing potential aquifer storage and recovery operations, indicated the additional recharge distributed throughout the area had minimal effects on streamflow in the nearby Grape Creek. An analysis of subregional groundwater budgets showed approximately 54 percent of the additional recharge flowed back to nearby Grape Creek, and the other 46 percent was distributed laterally into adjacent cells in the alluvial aquifer. The comparison of simulations and subregional water budget show the additional recharge did not substantially alter groundwater-level elevations or basin wide groundwater storage. Although the analysis of additional recharge provided in the numerical groundwater-flow model considers only one of many possible recharge scenarios, the model provides a useful tool that could be modified for various scenarios to understand potential effects of managed aquifer recharge.

Colorado↗

USGS2026

Rapid characterization of the 2025 Mw 8.8 Kamchatka, Russia earthquake

The 29 July 2025 M w 8.8 Kamchatka, Russia, earthquake was the sixth largest instrumentally recorded earthquake. This event was seismically well observed at regional and teleseismic distances, but publicly available near‐source data were sparse at the time of the event, presenting unique challenges for rapid source and impact characterization. The U.S. Geological Survey (USGS) National Earthquake Information Center provides global real‐time monitoring for earthquakes, including rapid response information products that estimate source characteristics, shaking, and the resulting impacts. We describe the USGS rapid response earthquake information products following the Kamchatka event and discuss their implications for ongoing hazards in the region. We describe potential improvements to our response workflows motivated by this event, including more rapid constraints on source geometries and the automated selection of fault geometries for finite‐fault inversions. The rapid response products together support the interpretation of a unilateral southwestward rupture with significant slip on the southwestern end of the rupture extent. The M w 8.8–9.0 event in 1952, which ruptured a comparable extent of the Kuril–Kamchatka subduction interface, has many similarities to the 2025 rupture. This illustrates that slip deficits may remain following great earthquakes and highlights the usefulness of comparative studies between historic and modern events.

Kuril-Kamchatka subduction zone↗

USGS1998

Water resources of Mellette and Todd counties, South Dakota

Mellette and Todd Counties are located in south-central South Dakota and have a combined area of 2,694 square miles. The White River and its tributaries, which include the Little White River, drain Mellette County and about one-half of Todd County. Tributaries to the Niobrara River, which include the Keya Paha River, drain the other one-half of Todd County. The average discharge of the Little White River is about 56 cubic feet per second as the river enters Todd County and is about 131 cubic feet per second as it discharges to the White River in northern Mellette County. The average discharge of the Keya Paha River just outside Todd County is about 39 cubic feet per second. The average annual runoff for Mellette and Todd Counties ranges from 0.94 to 2.36 inches based on records from nine streamflow-gaging stations in and near the counties. The average annual runoff is 1.62 inches, which compares with the average annual precipitation of about 19 inches. In Todd County, shallow wells completed in the alluvial, Ogallala, Arikaree, and White River aquifers generally can supply water that has low concentrations of dissolved solids, is fresh, and is soft to moderately hard. Ground water from shallow aquifers is limited in Mellette County; therefore, deep wells, often greater than 1,000 feet, are sometimes installed. The Pierre Shale often is used to supply rural domestic and stock wells in Mellette County even though well yields are low and the water has high dissolved solids, is moderately saline, and is very hard. Alluvial aquifers are present in both counties and store an estimated 1.6 million acre-feet of water. The water quality of the alluvial aquifers is dependent on the underlying deposits, and generally the water has low concentrations of dissolved solids, is fresh, and is soft to moderately hard where underlain by the Ogallala and Arikaree Formations; has moderate concentrations of dissolved solids, is slightly saline, and is hard where underlain by the White River Group; and has high concentrations of dissolved solids, is saline, and is very hard where underlain by the Pierre Shale. Also, yields often are lower where the alluvial aquifers are underlain by the Pierre Shale. The Ogallala aquifer is present in only Todd County, and the Arikaree aquifer is present throughout most of Todd County and southwestern and south-central Mellette County. The Ogallala aquifer contains an estimated 17 million acre-feet of water in storage, and the Arikaree aquifer contains an estimated 50 million acre-feet of water in storage. Both aquifers generally are suitable for irrigation, and yields from these aquifers are sometimes greater than 1,000 gallons per minute. Nitrate concentrations in 13 out of 92 water samples collected from the Ogallala aquifer exceeded the Primary Drinking Water Maximum Contaminant Level (MCL) of 10 milligrams per liter. In 11 out of 46 samples collected from the Arikaree aquifer, arsenic concentrations exceeded the MCL of 50 micrograms per liter. The White River aquifer, where present, is usually the shallowest source of ground water in Mellette County. The White River aquifer also is used in northern Todd County where the Ogallala and Arikaree aquifers are not present. The White River aquifer contains an estimated 50 million acre-feet of water in storage. Reported yields from the aquifer range from 1 to 30 gallons per minute, which generally is insufficient to support irrigation in most areas. However, yields are sufficient for livestock-watering and rural-domestic purposes. In both counties, the Pierre Shale is the shallowest bedrock aquifer and is exposed at the land surface throughout most of Mellette County. This aquifer is used primarily in Mellette County. Although the aquifer contains an estimated maximum of 1.5 million acre-feet of water in storage, it is not a viable source of ground water because the aquifer is relatively impermeable, yields are low, and water usually can be obtained from shallower sources, especially in Todd County. Reported yields from the Pierre Shale aquifer range from 1 to 8 gallons per minute. Because few test holes and wells penetrate below the Pierre Shale, little is known about the extent of the deeper bedrock aquifers. All wells completed in the Dakota Sandstone, Inyan Kara, and Minnelusa and Madison aquifers in the counties are used for stock-watering purposes. High concentrations of dissolved solids and hard water are characteristic of the water quality in the bedrock aquifers. Depths to the top of the deeper bedrock aquifers range from 1,270 feet to greater than 2,000 feet below land surface.

South Dakota↗

USGS2026

Design and function of the Autonomous Benthic Imaging and Surveying System (ABISS) for remote sensing of lake and seabed environments

Lake and seabed environments are home to fisheries and other biota that are important to ecosystems and economies, yet these environments and the species that use them are difficult to accurately assess and monitor. Traditional benthic survey techniques, like bottom trawling used by the U.S. Geological Survey, are limited by substrate constraints, poor spatial resolution and precision, and operational depth limits, hindering accurate assessment of benthic species and habitats. In response to these limitations, the U.S. Geological Survey developed the Autonomous Benthic Imaging and Surveying System, a camera system integrated into underwater vehicles, to capture high-resolution images of the lakebed. The system uses color and stereo cameras to collect imagery, which can be analyzed using computational methods to detect organisms and (or) characterize habitat features, such as geologic substrate types. The system has been integrated into autonomous underwater vehicles and into an underwater housing used by self-contained underwater breathing apparatus (SCUBA) divers. Although the engineering of the system was motivated by the need for data collection in the Great Lakes, it has potential to collect high quality data in any aqueous setting with sufficient water clarity and safe operating conditions. The Autonomous Benthic Imaging and Surveying System can operate across diverse depths and light conditions to map and quantify ecological patterns that were difficult or impossible to assess using traditional methods. The Autonomous Benthic Imaging and Surveying System offers the potential for accurate and precise monitoring and assessment of native benthic biota, invasive species, and habitat, potentially providing natural resource managers with improved information to support decision making about benthic resource management.

Great Lakes↗

USGS2024

Are field observations of surface rupture useful? An example from the 2023 Mw 7.8 Pazarcık, Turkey (Türkiye), earthquake

Field investigations have long been an important component of the scientific response to surface‐faulting earthquakes. However, in light of advances in remote data and models, the question arises whether field‐based observations of surface rupture remain useful for understanding rupture processes and seismic hazards. We approach this question using a field‐based study of the central 2023 M w 7.8 Pazarcık, Turkey (Türkiye), earthquake rupture, at the intersection of the east Anatolian fault (EAF) and Narlı fault. Our field observations include the surface rupture expression and extent of the central EAF and northernmost Narlı fault in generally forested and steep terrain and 68 measurements of left‐lateral surface displacement. These data improve our understanding of the Pazarcık rupture complexity, resolve the surface geometry of the Narlı fault–EAF connection, and exhibit a clear (>2 m) change in surface displacement across this intersection zone that confirms remote‐based coseismic slip models. Our study shows that focusing field efforts in areas of obscured or low‐resolution remote data can yield essential data for refining rupture extent, documenting perishable on‐fault displacement, and improving postearthquake situational awareness. A comparison of similarly large‐magnitude continental surface‐rupturing earthquakes indicates that displacement uncertainties relate to a complex set of factors, including measurement methods, rupture complexity, and displacement magnitude. Our study validates the need for postearthquake field observations, which, when driven by clear motivating questions and knowledge of methodological strengths and limitations, provide high‐resolution rupture data that complement remote‐based models.

Pazarcık↗

USGS2024

California State Waters Map Series—Benthic habitat characterization in the region offshore Humboldt Bay, California

Coastal and Marine Ecological Classification Standard (CMECS) geoform, substrate, and biotic component geographic information system (GIS) products were developed for the California State Waters of northern California in the region offshore of Humboldt Bay. The study was motivated by interest in development of offshore wind-energy capacity and infrastructure in Federal waters offshore. This project, carried out by the U.S. Geological Survey (USGS), resulted in four data releases for individual map blocks that are part of the “California State Waters Map Series”: (1) Offshore of Arcata, (2) Offshore of Eureka, (3) Offshore of the Eel River, and (4) Offshore of Cape Mendocino. The study area consists of 436 square kilometers of multibeam echo sounder (MBES) data acquired by Fugro Pelagos, Inc., in 2007. Towed camera-sled video was acquired in 2009 and 2010 to supervise the classification of the MBES data into habitats, and single channel sparker data were collected to calculate sediment thickness above the transgressive unconformity. Using video observations of habitat as ground truth, derivatives of the MBES data were classified into 3 seafloor character types (hard-rugose, hard-flat, and soft-flat), 26 induration-slope-depth groups, and 15 geoforms. The study area substrate is predominantly soft-flat sediment (mud and fine sand) covering 73.6 percent of the area. Hard-flat substrate areas, predominantly coarse sediment in scour depressions, cover 5.4 percent of the study area. The hard-rugose substrate areas are primarily outcrops of layered sedimentary bedrock and constitute 20.9 percent of the study area. Fifteen geoforms were identified in the analysis. The predominant geoforms mirror the seafloor character results, shelf geoforms, rock outcrop geoforms, and scour depression geoforms. Rock and scour areas are restricted to the southern portion of the study area off Cape Mendocino where uplift has exposed bedrock. On the flat shelf area post-transgressive sediment varies in thickness from 1.7 meters (m) nearshore to 28.1 m offshore.

California↗

USGS2025

Generalized Bancroft algorithm for locating earthquakes with P- and S-wave arrival times

Because of similarities between locating an earthquake with seismic stations and locating a Global Positioning System (GPS) receiver from satellites, the Bancroft algorithm developed for GPS processing can be used to locate earthquakes. Such an approach to earthquake location differs from the conventional method of choosing an initial or trial solution and then iteratively improving the solution until convergence. The Bancroft algorithm has the advantage of being a direct, noniterative solution but with the disadvantage of only being able to accommodate a homogeneous velocity model. An additional limitation of the standard Bancroft algorithm is that it considers arrival times in a medium with a single propagation velocity. This poses no problem for GPS processing because electromagnetic waves travel at the speed of light; however, for seismic waves it means the algorithm can be applied to collections of either P ‐ or S ‐wave arrival times. Here, I show how the Bancroft algorithm can be generalized to handle both P ‐ and S ‐wave arrival‐time measurements simultaneously. I also show how to accommodate depth‐varying P ‐ and S ‐wave velocity models. I apply the generalized Bancroft algorithm to microearthquakes beneath Tanaga Volcano in Alaska and compare standard locations from the widely used HYPOINVERSE location code to Bancroft locations and to the output of HYPOINVERSE when setting the trial location to the Bancroft location. I find the Bancroft locations outperform the results from the other methods for shallow earthquakes near sea level, where a quantity known as the geometric dilution of precision is large and linearized approaches such as HYPOINVERSE are expected to struggle.

Alaska↗

USGS2025

Geologic map of the Guinevere Planitia quadrangle (V–30), Venus

This 1:5,000,000-scale geologic map of the Guinevere Planitia quadrangle divides the region into 15 geologic material units, defined using Magellan synthetic aperture radar (12.6-centimeter-wavelength radar system; 75 meters per pixel) datasets and including upland terrain units (2.4 percent of the surface area), plains materials units (59 percent), flow materials associated with named and unnamed eruptive centers (37.2 percent), small volcanic edifices, and impact crater materials (1.4 percent). Upland terrain units consist of tessera and lineated upland material, plains materials consist of Guinevere regional plains and Guinevere lineated and mottled plains, and flow materials consist of lobate flow material and plains-forming flow material. Specific lobate flows associated with Atanua Mons, Tuli Mons, Var Mons, and Uilata Fluctus are mapped separately. Other mapped units are impact crater material and small volcanic edifice. In addition to geologic units, we mapped linear features that show patterns of deformation or flow across the quadrangle. These consist of faults, wrinkle ridges, broad arches, channels, troughs, and flow direction indicators. The map region also contains several small volcanic features: shields, depressions, and craters. These, in combination with the plains, large volcanoes, and coronae, show the pervasive influence of volcanism across Venusian lowlands. The rims of nine identified impact features are delineated; large bright and dark haloes, which in some cases are associated with individual impact craters, are mapped as surficial mantling deposits. We documented spatial relationships using the stratigraphic and cross-cutting relationships of the quadrangle’s geologic units and features to provide a synthesis of the region’s geologic history. The upland terrain of the quadrangle indicates intense tectonic deformation and uplift. It is exposed as embayed remnants, typically within the plains, and represents the oldest geologic materials locally and across the region. Guinevere plains and the plains-forming flow unit appear to be assemblages of volcanic flows from multiple sources, including distinct coronae and corona-like structures. The temporal evolution of Guinevere lineated and mottled plains was likely protracted, with continued formation of small volcanic edifices over a long period. The morphologic and radar brightness characteristics of volcanoes in the region indicate their growth may have involved (1) multiple large-scale eruptive centers with recognizable spatial and temporal sequences, (2) extensive lava flow fields with a multitude of flows producing complex, overlapping patterns, and (3) numerous small volcanic edifices, including shields, domes, and cones. Although geologic patterns common to other regions of Venus are evident in the Guinevere Planitia quadrangle, local relative age relationships are inconsistent or unclear, preventing robust stratigraphic correlation. The mapping results do, however, indicate complicated local sequences of volcanic and tectonic activity.

Scientific Investigations Map↗

USGS2024

Characteristics of the fault damage zone From high-resolution seismic imaging along the Palos Verdes Fault, California

The distribution and intensity of fault damage zones provides insight into fault activity and its relationship to fluid flow in the crust. Presently, measures of the in-situ distribution of fault damage remain limited and along-strike studies are rare. This study focuses on an offshore section Palos Verdes Fault damage zone that spans 28 km, near Los Angeles, California. To investigate the previously unresolved shallow (∼400 m below the seafloor) fault damage zone we use densely spaced (∼500 m line separation) newly collected sparker multichannel seismic lines and sub-bottom profiles. The combination of high-resolution acquisition methods and specialized seismic processing workflows provide improved imaging of shallow faulting. We apply a multi-trace similarity technique to identify discontinuities in the seismic data that may be attributed to faults and fractures. This fault detection approach reveals diverse fault damage patterns on adjacent seismic profiles. However, a discernible damage zone pattern emerges by stacking multiple damage detection profiles along strike. We find that peak damage identified in this way corresponds to the active main fault strand, confirmed in this study, and thus the technique may be useful for identifying active fault strands elsewhere. Additionally, we observe that the variable width of the damage zone along strike is controlled by fault obliquity. Furthermore, our observations reveal a correlation between fault damage and seafloor fluid seeps visible in the water column, suggesting that damage plays a role in controlling fluid flow around the fault.

California↗