USGS Science⌕ Search

SEARCH · USGS Science

Results for “Special Report”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42Linked to original sources

Regional hydrogeological screening characteristics used for siting near-surface waste-disposal facilities in Oklahoma, U.S.A.

The Oklahoma Geological Survey has developed several maps and reports for preliminary screening of the state of Oklahoma to identify areas that are generally acceptable or unacceptable for disposal of a wide variety of waste materials. These maps and reports focus on the geologic and hydrogeologic parameters that must be evaluated in the screening process. One map (and report) shows the outcrop distribution of 35 thick shale or clay units that are generally suitable for use as host rocks for surface disposal of wastes. A second map shows the distribution of unconsolidated alluvial and terrace-deposit aquifers, and a third map shows the distribution and hydrologic character of bedrock aquifers and their recharge areas. These latter two maps show the areas in the state where special attention must be exercised in permitting storage or disposal of waste materials that could degrade the quality of groundwater. State regulatory agencies and industry are using these maps and reports in preliminary screening of the state to identify potential disposal sites. These maps in no way replace the need for site-specific investigations to prove (or disprove) the adequacy of a site to safely contain waste materials. ?? 1991 Springer-Verlag New York Inc.

Environmental Geology and Water Sciences↗

Introduction to special section: The Trans-Alaska Crustal Transect (TACT) across Arctic Alaska

This special section of the Journal of Geophysical Research addresses the composition and structural evolution of the lithosphere in northern Alaska. Investigations reported in this section were mainly undertaken as part of the Trans‐Alaska Crustal Transect (TACT), an integrated geological and geophysical transect of the entire Alaskan lithosphere along a north‐south corridor undertaken from 1984 to 1992 (Figure 1). The onshore segment of the transect approximately follows along the route of the trans‐Alaskan pipeline; the offshore segment extends across the continental margin in the Gulf of Alaska to the Pacific plate. The TACT line is unique in that it provides a coordinated onshore/offshore geological and geophysical traverse of the North American plate in Alaska from the active convergent Pacific margin to the passive Arctic margin of the continent.

Alaska↗

Earthquakes & Volcanoes, Volume 23, Number 6, 1992

Earthquakes and Volcanoes is published bimonthly by the U.S. Geological Survey to provide current information on earthquakes and seismology, volcanoes, and related natural hazards of interest to both generalized and specialized readers.

Report↗

Geographic Names Information System

The Geographic Names Information System (GNIS) is an automated data system developed by the U.S. Geological Survey (USGS) to standardize and disseminate information on geographic names. GNIS provides primary information for all known places, features, and areas in the United States identified by a proper name. The information in the system can be manipulated to meet varied needs. You can incorporate information from GNIS into your own data base for special applications.

Report↗

Field surveying and topographic mapping in Alaska: 1947-83

The U.S. Geological Survey's earliest presence in Alaska dates back to 1889. A decade later, topographic mapping became an integral part of the Geological Survey's Alaska program, mostly as reconnaissance-type mapping and special-purpose mapping of specific sites. It was not until after World War II that the Survey's Alaska topographic mapping efforts began to bear fruit. This circular retraces surveying and topographic mapping by the Geological Survey in Alaska from 1947 to 1983 and describes camp life and some of the unusual happenings involved in working in virtually uninhabited country, adverse weather, and difficult terrain. A year-by-year recap of activities documents the transition from early small-scale mapping efforts to more accurate and detailed 1:63,360-scale mapping for Alaska except the Aleutian Islands and isolated islands in the Bering Sea. Recent 1:25,000-scale metric mapping and the preparation of orthophotographs and special mapping efforts for other Government agencies also are recounted.

Alaska↗

Cost-Benefit Analysis of Computer Resources for Machine Learning

Machine learning describes pattern-recognition algorithms - in this case, probabilistic neural networks (PNNs). These can be computationally intensive, in part because of the nonlinear optimizer, a numerical process that calibrates the PNN by minimizing a sum of squared errors. This report suggests efficiencies that are expressed as cost and benefit. The cost is computer time needed to calibrate the PNN, and the benefit is goodness-of-fit, how well the PNN learns the pattern in the data. There may be a point of diminishing returns where a further expenditure of computer resources does not produce additional benefits. Sampling is suggested as a cost-reduction strategy. One consideration is how many points to select for calibration and another is the geometric distribution of the points. The data points may be nonuniformly distributed across space, so that sampling at some locations provides additional benefit while sampling at other locations does not. A stratified sampling strategy can be designed to select more points in regions where they reduce the calibration error and fewer points in regions where they do not. Goodness-of-fit tests ensure that the sampling does not introduce bias. This approach is illustrated by statistical experiments for computing correlations between measures of roadless area and population density for the San Francisco Bay Area. The alternative to training efficiencies is to rely on high-performance computer systems. These may require specialized programming and algorithms that are optimized for parallel performance.

Open-File Report↗

Groundwater-quality and select quality-control data from the National Water-Quality Assessment Project, January through December 2015, and previously unpublished data from 2013 to 2014

Groundwater-quality data were collected from 502 wells as part of the National Water-Quality Assessment Project of the U.S. Geological Survey National Water-Quality Program and are included in this report. Most of the wells (500) were sampled from January through December 2015, and 2 of them were sampled in 2013. The data were collected from five types of well networks: principal aquifer study networks, which are used to assess the quality of groundwater used for public water supply; land-use study networks, which are used to assess land-use effects on shallow groundwater quality; major aquifer study networks, which are used to assess the quality of groundwater used for domestic supply; enhanced trends networks, which are used to evaluate the time scales during which groundwater quality changes; and vertical flow-path study networks, which are used to evaluate changes in groundwater quality from shallow to deeper depths. Groundwater samples were analyzed for a large number of water-quality indicators and constituents, including major ions, nutrients, trace elements, volatile organic compounds, pesticides, radionuclides, and some constituents of special interest (arsenic speciation, chromium [VI], and perchlorate). These groundwater-quality data, along with data from quality-control samples, are tabulated in this report and in an associated data release. Some data from environmental samples collected in 2013 and quality-control samples collected in 2014 also are included in the associated data release; these data are associated with networks described in this report and have not been published previously.

Data Series↗

Ground-water geology of the coastal zone, Long Beach-Santa Ana area, California

This paper is the first chapter of a comprehensive report on the ground-water features in the southern part of the coastal plain in Los Angeles and Orange Counties, Calif., with special reference to the effectiveness of the so-called coastal barrier--the Newport-Inglewood structural zone--in restraining landwar,-1 movement of saline water. The coastal plain in Los Angeles and Orange Counties, which covers some 775 square miles, sustains a large urban and rural population, diverse industries, and intensive agricultural developments. The aggregate ground-water withdrawal in 1945 was about 400,000 acre-feet a year, an average of about 360 million gallons a day. The dominant land-form elements are a central lowland plain with tongues extending to the coast, bordering highlands and foothills, and a succession of low hills and mesas aligned northwestward along the coastal edge of the central low- land plain. These low hills and mesas are the land-surface expression of geologic structure in the Newport-Inglewood zone. The highland areas that border the inland edge of the coastal plain are of moderate altitude and relief; most of the ridge crests range from 1,400 to 2,500 feet in altitude, but Santiago Peak in the Santa Ana Mountains attains a height of 5,680 feet above sea level. From these highlands the land surface descends across foothills and aggraded alluvial aprons to the central lowland, Downey Plain, here defined as the surface formed by alluvial aggradation during the post-Pleistocene time of rising base level. The Newport-Inglewood belt of hills and plains (mesas) has a maximum relief of some 500 feet but is widely underlain at a depth of about 30 feet by a surface of marine plantation. As initially formed in late Pleistocene time that surface was largely a featureless plain. Thus the present land-surface forms within the Newport-Inglewood belt measure the earth deformation that has occurred there since late Pleistocene time and so are pertinent with respect to structural features that influence the watertightness of the so-called coastal barrier. The hills and mesas of the Newport-Inglewood belt are cut by six gaps through which tongues of the central lowland extend to the coast. The gaps are trenched in the deformed late Pleistocene surface and are floored with alluvium that is highly permeable in its lower part. The Long Beach-Santa Ana area, with which this report is concerned, encompasses the central and eastern segments of the coastal plain, and includes five of the gaps in succession from northwest to south- east: Dominguez, Alamitos, Sunset, Bolsa, and Santa Ana Gaps. In the Long Beach-Santa Ana area a thick sequence of Quaternary and Tertiary sedimentary rocks has been deposited on a basement of metamorphic and crystalline rocks of pre-Tertiary age. In the broad syncline underlying tl e central part of Downey Plain these sediments probably exceed 20,000 feet in thickness. This report pertains chiefly to the geology and water-bearing character of the rocks that underlie the coastal zone of the Long Beach-Santa Ana area. This area extends some 27 miles from Dominguez Hill on the northwest to Newport Beach on the southeast, has an average width of about 6 miles, includes some 180 square miles, and borders the Pacific Ocean. Of the Quaternary deposits the youngest are of Recent age and comprise silt, sand, gravel, and clay, chiefly of fluvial origin; they are the latest contributions to the alluvial cones of the Los Angeles, San Gabriel, and Santa Ana Rivers; their thickness is as much as 175 feet. The upper division of the Recent deposits, largely fine sand and silt of low permeability, commonly furnishes water only to a few wells of small yield; the lower division is coarse sand and gravel deposited chiefly in two tongues extending respectively, from Whittier Narrows through Dominguez Gap and from Santa Ana Canyon through Santa Ana Gap.

California↗

Stratigraphic sections of the Phosphoria formation in Montana

The first of a series of reports giving detailed stratigraphic sections of the Phosphoria formation in the Western phosphate field as measured and described by the Geological Survey will be released as Circulars within the next few months. Because of the needs of industry for many of these data during the 1951 field season, and in view of the unavoidable delays attendant on publication, the tabular data to be included in these Circulars are hereby placed on open file in simple reproduction form (prepared by Ozalid from photographic negatives) and without explanatory text so that immediate use may be made of the data. The tables include data on sections in four states: Montana, Idaho, Wyoming, and Utah; and the tables for each of these states are bound together as individual reports. The tables include name and location of section measured, brief description of geologic setting, acknowledgments for field and analytical work, abstract data on the sections (bed number, rock name, sample number, and thickness), and analytical data on the samples. The analytical data include reports on P 2 O 5 and acid insoluble for all samples and additional analyses, such as Al 2 0 3 , Fe 7 0 3 , loss on ignition, F, and V 2 O 5 , for selected samples. Spectrographic analyses for a large number of elements are included samples from selected localities, and special analyses have been made of a few samples. The work in Montana has been done with the aid of Missouri River Basin funds as part of a Program of appraisal of the Missouri Basin mineral resources. These reports are placed on open file at the offices of the Geological Survey in Washington, D. C., Spokane, Washington, Salt Lake City, Utah, and Montpelier, Idaho, and at the offices of the Idaho Bureau of Mines and Geology, Moscow, Idaho, the Montana Bureau of Mines and Geology, Butte, Montana, the Wyoming Geological Survey, Laramie, Wyoming, and the University of Utah, Salt Lake City, Utah.

Montana↗

The GSHAP Global Seismic Hazard Map

Minimization of the loss of life, property damage, and social and economic disruption due to earthquakes depends on reliable estimates of seismic hazard. National, state, and local governments, decision makers, engineers, planners, emergency response organizations, builders, universities, and the general public require seismic hazard estimates for land use planning, improved building design and construction (including adoption of building construction codes), emergency response preparedness plans, economic forecasts, housing and employment decisions, and many more types of risk mitigation. The Global Seismic Hazard Assessment Program (GSHAP) was designed to assist in global risk mitigation by providing a useful global seismic hazard framework and by serving as a resource for any national or regional agency for further detailed studies applicable to their needs. GSHAP was launched in 1992 by the International Lithosphere Program (ILP) with the support of the International Council of Scientific Unions (ICSU) and endorsed as a demonstration program in the framework of the United Nations International Decade for Natural Disaster Reduction (UN/IDNDR). GSHAP promoted a regionally coordinated, homogeneous approach to seismic hazard evaluation, including the production and distribution of the Global Seismic Hazard Map (GSH Map), a special issue of Annali di Geofisica (December 1999) describing the map and project, and a Web site (http://seismo.ethz.ch/GSHAP/) containing regional reports, GSHAP yearly reports, summaries, and maps of seismicity, source zones, and seismic hazard values.

Seismological Research Letters↗

Water quality at a biosolids-application area near Deer Trail, Colorado, 1993-1999

The Metro Wastewater Reclamation District (Metro District) in Denver, Colo., applied biosolids resulting from municipal sewage treatment to farmland in eastern Colorado beginning in December 1993. In mid-1993, the U.S. Geological Survey in cooperation with the Metro District began monitoring water quality at the biosolids-application area about 10 miles east of Deer Trail, Colo., to evaluate baseline water quality and the combined effects of natural processes, land uses, and biosolids applications on water quality of the biosolids application area. Water quality was characterized by baseline and post-biosolids-application sampling for selected inorganic and bacteriological constituents during 1993 through 1998, with some additional specialized sampling in 1999. The study included limited sampling of surface water and the unsaturated zone, but primarily focused on groundwater. See report for complete abstract.

Colorado↗

Groundwater-quality and select quality-control data from the National Water-Quality Assessment Project, January through December 2016, and previously unpublished data from 2013 to 2015

Environmental groundwater-quality data were collected from 648 wells as part of the National Water-Quality Assessment Project of the U.S. Geological Survey National Water-Quality Program and are included in this report. Most of the wells (514) were sampled from January through December 2016, and 60 of them were sampled in 2013 and 74 in 2014. The data were collected from seven types of well networks: principal aquifer study networks, which are used to assess the quality of groundwater used for public-water supply; land-use study networks, which are used to assess land-use effects on shallow groundwater quality; major aquifer study networks, which are used to assess the quality of groundwater used for domestic supply; enhanced trends networks, which are used to evaluate the time scales during which groundwater quality changes; vertical flow-path study networks, which are used to evaluate changes in groundwater quality from shallow to deeper depths; flow-path study networks, which are used to evaluate changes in groundwater quality from shallow to deeper depths over a horizontal distance; and modeling support studies, which are used to provide data to support groundwater modeling. Groundwater samples were analyzed for many water-quality indicators and constituents, including major ions, nutrients, trace elements, volatile organic compounds, pesticides, radionuclides, and some constituents of special interest (arsenic speciation, chromium [VI], and perchlorate). These groundwater-quality data, along with data from quality-control samples, are tabulated in this report and in an associated data release. Some data from environmental samples collected in 2013–14 and quality-control samples collected in 2012–15 also are included in the associated data release. Data from samples collected in 2016 are associated with networks described in this report and have not been published previously; data from samples collected between 2012 and 2015 are associated with networks described in previous reports in this data series.

Data Series↗