USGS Science⌕ Search

SEARCH · USGS Science

Results for “Climate of the Past”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,687 records · Page 39Linked to original sources
USGS2025

An evaluation of the effects of different deicing salt application rates on three watersheds in Essex County, New York

The U.S. Geological Survey, in cooperation with the New York State Department of Transportation, evaluated the effects of different deicing salt application rates on surface water, groundwater, and highway runoff quality near State highways in northern New York. Three reaches of State highways were tested with different deicing treatments between October 2019 and November 2022: a salt-sand mixture (Treatment A), a salt mixture applied at a lower rate (Treatment B), and a control mixture consistent with typical deicing salt amounts and application rates. Data on pavement conditions and the quality of surface water, highway runoff, and groundwater were collected. Surface electromagnetic data were also collected. Surface-water and groundwater quality downgradient from the State highways were compared with water quality at upgradient locations. The percentage of snow or ice coverage was used to evaluate the effectiveness of the salt applications. This report provides an overview of the transport of deicing salt. The Treatment B watershed had deicing mixture applied more frequently than other highway reaches, which caused it to have the highest annual total chloride application. Despite differences in chloride application, flow-weighted mean chloride concentrations in highway runoff were comparable across treatments. Chloride concentrations were elevated in surface water and groundwater downgradient from highways relative to chloride concentrations upgradient from highways. A chloride mass balance, calculated for one treatment watershed, indicated that groundwater affected by legacy deicing practices may be contributing additional chloride to surface water. Spatial patterns from electromagnetic surveys show a shallow saline plume alongside the highway in that area. Differences in winter severity and pavement-surface conditions drove deicing salt applications in the treatment areas. This study found that several factors affect chloride loads in the watersheds, including variable winter conditions, adaptive snow and ice management, legacy management practices, and area-specific aquifer and groundwater conditions.

New York↗
USGS2022

U-Pb scheelite ages of tungsten and antimony mineralization in the Stibnite-Yellow Pine district, central Idaho

The Stibnite-Yellow Pine district contains the largest antimony resource in the United States, as well as significant gold, and is a historic producer of tungsten. Application of in situ laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) direct dating of scheelite from two Au-Sb-W ore deposits, Yellow Pine and Hangar Flats, yielded an older group of U-Pb ages in the range of 60.0 ± 2.8 to 57.0 ± 1.1 Ma and a younger U-Pb age for scheelite intergrown with stibnite of 47.4 ± 1.1 Ma. These in situ analyses were calibrated by isotope dilution-thermal ionization mass spectrometry (ID-TIMS) U-Pb lower intercept ages of two coarsely crystalline scheelite samples that yielded ages of 57.52 ± 0.22 and 56.62 ± 0.16 Ma. Scheelite of the latter age is of sufficient quality to serve as a primary reference material for LA-ICP-MS scheelite U-Pb geochronology. The group of older U-Pb scheelite ages agrees with 40 Ar/ 39 Ar ages of 56.9 ± 1.2 to 56.38 ± 0.54 Ma on adularia from Yellow Pine and Hangar Flats, whereas the younger U-Pb scheelite age is similar to an 40 Ar/ 39 Ar age of 46.00 ± 0.40 Ma on adularia from an epithermal gold-silver deposit in the adjacent Thunder Mountain caldera. Our results indicate that the main stage of tungsten mineralization occurred at ca. 57 Ma, whereas the main stage of antimony mineralization occurred at ca. 47 Ma—thereby providing first-time age constraints for antimony and tungsten mineralization in the Stibnite-Yellow Pine district.

Idaho↗
USGS2026

Deep critical zone controls on shallow landslides

The deep critical zone (CZ) has long been recognized for its importance in influencing shallow landslides but was not considered feasible to include in slope stability models at the watershed scale. In this study, we demonstrate that simple approximations of the CZ in a fully coupled hydrologic and soil slope stability model can effectively capture the location, timing, and likely size of shallow landslides. To achieve this, we use coupled, process-based models that incorporate the effects of 1) deep CZ structures, 2) three-dimensional transient hydrology, and 3) multidimensional slope stability, calibrated with data from an intensively monitored field site. Our results show that the hydrologically active deep CZ guides groundwater flow, influencing where it drains from or exfiltrates to the soil mantle, producing distinct patterns of soil saturation and seepage forces at the soil-bedrock boundary. Deep conductive weathered critical zone drains the soil mantle, reducing the likelihood of destabilizing pore pressures, while the downslope thinning of the CZ forces groundwater to the surface. This creates localized instability and a tendency for similar-sized landslides across the landscape. In contrast, the absence of conductive weathered bedrock results in more widespread destabilizing pore pressures, leading to larger landslides and the likelihood of landslides earlier in a storm than in landscapes underlain by a deep CZ. Our findings suggest that first-order variations of deep CZ can provide physical explanations for variations observed in the susceptibility, magnitude, and timing of shallow landslides, and that CZ structure may be inferred from patterns and timing of landsliding.

Proceedings of the National Academy of Sciences↗
USGS2026

Groundwater source water assessment area delineation of public supply wells in the Treasure Valley, western Idaho

The Idaho Department of Environmental Quality (IDEQ) is responsible for assessing the source water for public water supply systems including the delineation of source water assessment areas for wells, which are defined as the subsurface areas contributing water to a well during a period of time. Part of the IDEQ assessment plan is to update source water assessments over time. The U.S. Geological Survey (USGS) developed a new groundwater-flow model for part of the western Snake River Plain aquifer in southwestern Idaho. This groundwater- flow model provided a new opportunity for IDEQ to update source water assessment for public water supply wells within the model boundary. The USGS, in cooperation with IDEQ, used the USGS Treasure Valley Groundwater Flow Model along with a MODPATH particle tracking post-processing program to reassess public-water supply source water assessment areas. The USGS created an automated script that requests a well location, depth, and pumpage rate, and then incorporates that information into the Treasure Valley Groundwater Flow Model combined with the MODPATH model to create 3-, 6-, and 10-year time of travel zones that are output to a geographic information system shapefile. The TVSWA_Delineator script provides a fast, transparent tool for IDEQ to reassess or create new public-water supply source water assessment area delineations based on new and updated information and is available as a Python script and a Windows executable with the compiled script and all necessary components. TVSWA_Delineator utilizes a quadtree approach to rediscretize the Treasure Valley Groundwater Flow Model grid around the pumping well location from 1-mile cell lengths telescoped down to 1/16 mile. This rediscretization increases the source water assessment area delineation resolution near the pumping well and minimizes the effect of weak sinks in the MODPATH model. The stress inputs for each month of the final 10 years (2006 to 2015) of the Treasure Valley Groundwater Flow model historical simulation were averaged for the particle tracking analysis. The MODPATH model used backwards tracking of particles released at each stress period to create the source water assessment area delineations. This report documents the creation of the TVSWA_Delineator Python script, including adaptations made to the Treasure Valley Groundwater Flow Model, creation of a companion MODPATH model, and post-processing results to provide source water assessment areas.

Idaho↗
USGS2024

Utilization of stochastic ground motion simulations for scenario-based performance assessment of geo-structures

Probabilistic seismic performance assessments of engineered structures can be highly sensitive to the seismic input excitation and its variability. In the present study, the scenario-based performance assessment recommended by Federal Emergency Management Agency (FEMA) P-58 guidelines is adopted to estimate seismic fragility of concrete dams for various seismic hazard scenarios. Due to the scarcity of recorded ground motions and thereby their poor representation of uncertainties, stochastic ground motion simulation methods are utilized to obtain the required input excitations. Moreover, to understand the uncertainty in ground motion simulation models, two broadband stochastic simulation models are used to generate input excitations representing six seismic hazard scenarios defined by earthquake magnitude, source-to-site distance, and soil conditions. Optimal intensity measure parameters for each scenario are identified using a systematic procedure that considers criteria such as efficiency, practicality, proficiency, sufficiency, and hazard compatibility. Fragility curves and surfaces are derived using the cloud analysis technique, taking into account various damage measures and limit state functions. The study finds that the derived fragility curves are particularly sensitive to the selection of earthquake scenarios, the choice of records, and the methods used to calculate fragility curves, with less sensitivity observed to different engineering demand parameters. Given this sensitivity, particularly to ground motion selection, the study highlights the necessity of incorporating both model-to-model variability (epistemic uncertainty) and record-to-record variability (aleatory uncertainty), alongside the established material and modeling uncertainties, in the probabilistic seismic assessment.

Reliability Engineering and System Safety (RESS)↗
USGS2025

An exploration of the relative influence of physical models for Omori’s law

Omori’s law states that the rate of aftershocks decays as a function of inverse time. There are multiple physical explanations that we reduce into a nonlinear mixed effects relation of three terms: (1) a Rate/State expression that can account for static/dynamic and viscoelastic triggering caused directly by the mainshock, (2) a fluid diffusion triggering term, and (3) a randomized secondary triggering (cascade) term. We fit free physical-model parameters to an observed aftershock sequence through two nonlinear regression methods to find the relative contributions of physics-based models in an observed aftershock sequence. Results from both methods show that Rate/State models overpredict aftershock rates by ∼0–30%. Secondary aftershocks cause a net negative contribution (seismicity rate reduction that corrects overprediction by other terms) ranging between ∼0 and 30%. All regression solutions yield negative secondary triggering contributions without being guided to do so. A physical explanation for this is that aftershock occurrence relieves stress from the crust, ultimately causing the sequence to extinguish itself. Fluid diffusion triggering contributions range from ∼0 to 20%. Diffusion processes are observed to be shorter in time than the full duration of an aftershock sequence and they are also spatially limited, diminishing their influence. Our results apply to an aftershock decay curve from the 2016 Central Apennines earthquake sequence, meaning that our specific results may not be general. Our primary conclusion is that any one physical model cannot alone fit the observed sequence as well as the combination of three we investigated.

Frontiers in Earth Science↗
USGS2026

Evolution of arsenic speciation during thermal treatment simulating wildfire heating in arsenic-rich sediments

Understanding arsenic transformations during wildfires can help better constrain the environmental impacts of increased wildfire intensity, frequency, and burned area. Previous studies have monitored the evolution of metal(loid) speciation at specific time/temperature endpoints, hampering the comprehension of the dynamic transformations of metal(loid)s during wildfires. Here, a novel approach, namely in situ time-resolved X-ray absorption near edge structure (TR-XANES) spectroscopy, was used for the first time to monitor the heat-induced redox transformations of arsenic (As) in two As-rich sediments with different characteristics. No arsenic transformations were observed in either sediment at room temperature or when the sediments were heated to a maximum temperature of 400 ºC. When heated to a maximum temperature of 600 or 700 ºC, As underwent complex, dynamic, and partially reversible redox transformations, the extent of which varied with sediment properties, initial As speciation, and heating temperature and duration. In the case of sediments initially containing As(V) and a low sulfide/sulfate ratio, the As(V) was reduced to As(III) over a short period of time, followed by immediate reoxidation of As(III) to As(V). The extent of the transient As reduction increased with increasing maximum temperature. The final As speciation at the end of the heating experiment was not substantially different from that at the beginning of the experiment. In contrast, in sediments that were best described by a more complex combination of reference compounds (As(V) coprecipitated with or adsorbed on iron oxide, arseniosiderite, arsenopyrite) with a high sulfide/sulfate ratio, As(V) phases were reduced to As(III) and As(III) was further reduced to As(-I) (at 700 ºC, only), followed by delayed reoxidation of As(-I) to As(III) (at 700 ºC, only) and reoxidation of As(III) to As(V). Approximately 9% and 26% of all As remained as As(III) ( i.e., was not reoxidized to As(V)) at the end of the experiment when heated to a maximum temperature of 600 and 700 ºC, respectively, which is higher than the relative abundance of As(III) in the native sediment. These fire-induced As transformations can potentially enhance As mobilization to surface water and groundwater, posing risks to environmental and human health.

California↗
USGS2025

Quality of groundwater used for domestic supply in the Gilroy-Hollister basin and surrounding areas, California, 2022

More than 2 million Californians rely on groundwater from domestic wells for drinking-water supply. This report summarizes a 2022 California Groundwater Ambient Monitoring and Assessment Priority Basin Project (GAMA-PBP) water-quality survey of 33 domestic and small-system drinking-water supply wells in the Gilroy-Hollister Valley groundwater basin and the surrounding areas, where more than 20,000 residents are estimated to utilize privately owned domestic wells. The study area includes the Llagas subbasin in the north, the North San Benito subbasin in the south, and the surrounding uplands. The study was focused on groundwater resources used for domestic drinking-water supply, which are mostly drawn from shallower parts of aquifer systems rather than those of groundwater resources used for public drinking-water supply in the same area. This assessment characterized the quality of ambient groundwater in the aquifer before filtration or treatment, rather than the quality of drinking water delivered to the tap. To provide context, the measured concentrations of constituents in groundwater were compared to Federal and California State regulatory and non-regulatory benchmarks for drinking-water quality. A grid-based method was used to estimate the areal proportions of groundwater resources used for domestic drinking wells that have water-quality constituents present at high concentrations (above the benchmark), moderate concentrations (between one-half of the benchmark and the benchmark for inorganic constituents, or between one-tenth of the benchmark and the benchmark for organic constituents), and low concentrations (less than one-half or one-tenth the benchmark for inorganic and organic constituents, respectively). This method provides statistically representative results at the study-area scale and permits comparisons to other GAMA-PBP study areas. In the study area, inorganic constituents in groundwater were greater than regulatory benchmarks (U.S. Environmental Protection Agency [EPA] or State of California maximum contaminant levels [MCLs]) for public drinking-water quality in 24 percent of domestic groundwater resources. The inorganic constituents present at concentrations greater than MCLs for drinking water were nitrate (as nitrogen), barium, chromium, and selenium. Total dissolved solids (TDS) or manganese were present at concentrations greater than the secondary maximum contaminant levels (SMCLs) that the State of California uses as aesthetic-based benchmarks in 48 percent of domestic groundwater resources. No volatile organic compounds or pesticide constituents were present at concentrations greater than regulatory benchmarks. Total coliform bacteria and enterococci were detected in 4 percent of domestic groundwater resources. Per- and polyfluoroalkyl substances (PFAS) were detected in 19 percent of domestic groundwater resources, and 10 percent had concentrations greater than recently enacted (April 2024) EPA MCLs. Physical and chemical factors from natural and anthropogenic sources that could affect the groundwater quality were evaluated using results from statistical testing of associations between constituent concentrations and potential explanatory variables. In this study, relevant physical factors include well construction characteristics, groundwater age, site proximity to groundwater recharge or discharge zones, and potential sources of contamination. Relevant chemical factors include the initial chemistry of the recharge water, the mineralogy of the aquifer sediments, and the subsequent shifts in chemistry as biologic and geologic reactions alter groundwater in the subsurface. Nitrate concentrations were correlated to agricultural land use, distance from the boundary of the Gilroy-Hollister Valley groundwater basin, and the proportion of modern (post-1950s) water captured by the well. Denitrification under anoxic redox conditions can mitigate some nitrate derived from fertilizer application. Total dissolved solids primarily were derived from water-rock interactions with soils and aquifer materials in the study area, but there were high concentrations where agricultural practices contributed additional TDS. Mineralogy of aquifer sediments and rocks also affect barium, selenium, boron, and chromium concentrations in the Gilroy-Hollister Valley groundwater basin. PFAS were positively correlated with urban land use and the proportion of modern water captured by the well.

California↗
USGS2025

Migration of seismicity from the mantle to the upper crust beneath Harrat Lunayyir volcanic field, Saudi Arabia

Harrat Lunayyir is a volcanic field in Saudi Arabia that experienced a Mw~5.4 earthquake driven by an upper-crustal dike intrusion in May 2009. This volcanic field has exhibited numerous forms of volcanic seismicity both prior to and since the 2009 dike intrusion. Significantly, earthquakes within the lithospheric mantle and, rarely, the lower crust are present in the two-decade long seismicity catalog of Harrat Lunayyir. Here we analyze 24 years of volcanic seismicity at Harrat Lunayyir from 1998 to 2022. We find that: 1) precursory seismicity began at least eight years prior to the 2009 event, with a particularly notable seismic episode one year prior; 2) lithospheric mantle seismicity is highly localized in space and in time, largely occurring in discrete sequences lasting on the order of a few hours to a few days; 3) one seismic sequence clearly migrates upward from the lithospheric mantle to the upper crust, including seismicity within the nominally ductile lower crust; 4) crustal seismicity has been slowly declining over time; and 5) lithospheric-mantle seismicity does not show any apparent decline with time. From these observations we infer that the seismicity is driven by magmatic fluids or volatiles, and seismic monitoring of this volcanic field should continue into the future.

Harrat Lunayyir volcanic field↗
USGS2025

Groundwater hydrology, groundwater and surface-water interactions, water quality, and groundwater-flow simulations for the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado, 2017–19

In 2017, the U.S. Geological Survey, in cooperation with the Upper Arkansas Water Conservancy District, began a study to provide a comprehensive analysis of the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado. The study included collection of data pertaining to groundwater hydrology, groundwater and surface-water interactions, and water quality in the alluvial aquifer. In addition to providing foundational information on the hydrology of the alluvial aquifer, a numerical groundwater-flow model was developed to estimate the potential effects of additional storage of groundwater in the alluvial aquifer. Groundwater-level elevation data from 30 wells were used to estimate groundwater-flow directions in the alluvial aquifer, which were generally from the southwest to northeast, away from the Sangre de Cristo Mountains and towards perennial streams in the center of the valley. Although some seasonal variation was apparent in groundwater-level elevation records, no statistically significant seasonal trends were indicated. Statistically significant long-term trends were indicated in groundwater-level elevation records for 8 of the 30 wells, and of these wells with statistically significant trends, all but 1 indicated a negative trend of groundwater-level elevations. Spatial evaluation of wells with statistically significant negative groundwater-level elevation trends showed many are in areas of denser well drilling for domestic or other uses, indicating increasing groundwater use could potentially be causing groundwater-level elevation declines. There were instances of wells with no statistically significant groundwater-level elevation trends also located in areas of greater density of well completions. Additional investigations may be necessary to more fully characterize the processes responsible for negative groundwater-level elevation trends. Streamflow gain or loss calculations were completed for low flow in 2017–19 and for high flow in 2018 in nine reaches of streams within the study area. Stream reaches of the upper Texas Creek, upper Grape Creek, upper-middle Grape Creek, and Taylor Creek displayed consistent streamflow loss in each period from 2017 to 2019. These stream reaches represent long-term sources of recharge to the alluvial aquifer. Streamflow gain or loss varies through time in other stream reaches (lower Texas Creek, lower-middle Grape Creek, lower Grape Creek below Westcliffe, and lower Grape Creek above DeWeese Reservoir). The temporally variable behavior indicates these stream reaches may be sources of groundwater recharge or areas of groundwater discharge, likely depending on temporal dynamics between the elevation of the water table and the stream. Water-quality samples were collected from 10 groundwater wells and 10 stream sites during September through November 2019. All groundwater and stream samples were analyzed for major and trace elements and stable isotopes of water. A subset of groundwater samples was also analyzed for the environmental tracers sulfur hexafluoride, tritium, and noble gases. Comparison of water-quality results to U.S. Environmental Protection Agency drinking water-quality standards indicated no constituents exceeded primary standards for human health. Spatial evaluation of water quality indicated the concentrations of various constituents are likely controlled by groundwater and surface-water interactions and by spatial variability in bedrock geology underlying the alluvial aquifer. Specifically, streams shown to gain from groundwater had water chemistry constituent compositions similar to groundwater, whereas streams exiting the Sangre de Cristo Mountains tended to have compositions consistent with snowmelt. Groundwater geochemistry appeared to be partially controlled by oxidation-reduction processes and by proximity to igneous rocks in the Wet Mountains. Environmental tracers used to estimate groundwater age indicated all sampled groundwater contained tracers representing modern recharge (approximately less than 65 years old) but mixing of premodern recharge (approximately more than 65 years old) also occurs. Spatial evaluation of environmental tracers indicated large faults may be conduits for upwelling of older groundwater. No trends were observed in groundwater age with well depth, indicating all sampled wells are located within the zone of active groundwater flow. The presence of modern groundwater in wells with statistically significant negative groundwater-level elevation trends indicates groundwater storage depletions may be partially offset by capture of modern recharge. Repeated sampling of groundwater age would be necessary, however, to determine if any trends in groundwater age exist, which may indicate changing groundwater recharge, storage, or discharge. Additional investigations could also consider quantifying groundwater age in deeper wells to more fully define the depth of active groundwater flow. A numerical groundwater-flow model was developed to estimate components of the water budget, simulate groundwater and surface-water interactions, and evaluate the potential effects of aquifer storage and recovery. Simulated groundwater-level elevations from the calibrated groundwater-flow model are similar to the observed pattern of groundwater-level elevations with higher elevations in the western part of the study area along the Sangre de Cristo Mountains. Simulated water-budget components indicate most of the recharge to the alluvial aquifer is derived from streamflow losses, which is consistent with observations of losing streams along the mountain front. The largest groundwater discharge component of the alluvial aquifer was to streams in the center of the valley, where observations of stream gain or loss indicated the predominance of gaining conditions. Comparison of groundwater and surface-water interactions between the calibrated groundwater-flow model for 2000-19 (the base-case model) and a simulation including additional recharge, representing potential aquifer storage and recovery operations, indicated the additional recharge distributed throughout the area had minimal effects on streamflow in the nearby Grape Creek. An analysis of subregional groundwater budgets showed approximately 54 percent of the additional recharge flowed back to nearby Grape Creek, and the other 46 percent was distributed laterally into adjacent cells in the alluvial aquifer. The comparison of simulations and subregional water budget show the additional recharge did not substantially alter groundwater-level elevations or basin wide groundwater storage. Although the analysis of additional recharge provided in the numerical groundwater-flow model considers only one of many possible recharge scenarios, the model provides a useful tool that could be modified for various scenarios to understand potential effects of managed aquifer recharge.

Colorado↗
USGS2025

Overview of The SCEC/USGS Community Stress Drop Validation Study using the 2019 Ridgecrest earthquake sequence

We present initial findings from the ongoing Community Stress Drop Validation Study to compare spectral stress‐drop estimates for earthquakes in the 2019 Ridgecrest, California, sequence. This study uses a unified dataset to independently estimate earthquake source parameters through various methods. Stress drop, which denotes the change in average shear stress along a fault during earthquake rupture, is a critical parameter in earthquake science, impacting ground motion, rupture simulation, and source physics. Spectral stress drop is commonly derived by fitting the amplitude‐spectrum shape, but estimates can vary substantially across studies for individual earthquakes. Sponsored jointly by the U.S. Geological Survey and the Statewide (previously, Southern) California Earthquake Center our community study aims to elucidate sources of variability and uncertainty in earthquake spectral stress‐drop estimates through quantitative comparison of submitted results from independent analyses. The dataset includes nearly 13,000 earthquakes ranging from M 1 to 7 during a two‐week period of the 2019 Ridgecrest sequence, recorded within a 1° radius. In this article, we report on 56 unique submissions received from 20 different groups, detailing spectral corner frequencies (or source durations), moment magnitudes, and estimated spectral stress drops. Methods employed encompass spectral ratio analysis, spectral decomposition and inversion, finite‐fault modeling, ground‐motion‐based approaches, and combined methods. Initial analysis reveals significant scatter across submitted spectral stress drops spanning over six orders of magnitude. However, we can identify between‐method trends and offsets within the data to mitigate this variability. Averaging submissions for a prioritized subset of 56 events shows reduced variability of spectral stress drop, indicating overall consistency in recovered spectral stress‐drop values.

California↗
USGS2026

Rapid characterization of the 2025 Mw 8.8 Kamchatka, Russia earthquake

The 29 July 2025 M w 8.8 Kamchatka, Russia, earthquake was the sixth largest instrumentally recorded earthquake. This event was seismically well observed at regional and teleseismic distances, but publicly available near‐source data were sparse at the time of the event, presenting unique challenges for rapid source and impact characterization. The U.S. Geological Survey (USGS) National Earthquake Information Center provides global real‐time monitoring for earthquakes, including rapid response information products that estimate source characteristics, shaking, and the resulting impacts. We describe the USGS rapid response earthquake information products following the Kamchatka event and discuss their implications for ongoing hazards in the region. We describe potential improvements to our response workflows motivated by this event, including more rapid constraints on source geometries and the automated selection of fault geometries for finite‐fault inversions. The rapid response products together support the interpretation of a unilateral southwestward rupture with significant slip on the southwestern end of the rupture extent. The M w 8.8–9.0 event in 1952, which ruptured a comparable extent of the Kuril–Kamchatka subduction interface, has many similarities to the 2025 rupture. This illustrates that slip deficits may remain following great earthquakes and highlights the usefulness of comparative studies between historic and modern events.

Kuril-Kamchatka subduction zone↗
USGS1998

Water resources of Mellette and Todd counties, South Dakota

Mellette and Todd Counties are located in south-central South Dakota and have a combined area of 2,694 square miles. The White River and its tributaries, which include the Little White River, drain Mellette County and about one-half of Todd County. Tributaries to the Niobrara River, which include the Keya Paha River, drain the other one-half of Todd County. The average discharge of the Little White River is about 56 cubic feet per second as the river enters Todd County and is about 131 cubic feet per second as it discharges to the White River in northern Mellette County. The average discharge of the Keya Paha River just outside Todd County is about 39 cubic feet per second. The average annual runoff for Mellette and Todd Counties ranges from 0.94 to 2.36 inches based on records from nine streamflow-gaging stations in and near the counties. The average annual runoff is 1.62 inches, which compares with the average annual precipitation of about 19 inches. In Todd County, shallow wells completed in the alluvial, Ogallala, Arikaree, and White River aquifers generally can supply water that has low concentrations of dissolved solids, is fresh, and is soft to moderately hard. Ground water from shallow aquifers is limited in Mellette County; therefore, deep wells, often greater than 1,000 feet, are sometimes installed. The Pierre Shale often is used to supply rural domestic and stock wells in Mellette County even though well yields are low and the water has high dissolved solids, is moderately saline, and is very hard. Alluvial aquifers are present in both counties and store an estimated 1.6 million acre-feet of water. The water quality of the alluvial aquifers is dependent on the underlying deposits, and generally the water has low concentrations of dissolved solids, is fresh, and is soft to moderately hard where underlain by the Ogallala and Arikaree Formations; has moderate concentrations of dissolved solids, is slightly saline, and is hard where underlain by the White River Group; and has high concentrations of dissolved solids, is saline, and is very hard where underlain by the Pierre Shale. Also, yields often are lower where the alluvial aquifers are underlain by the Pierre Shale. The Ogallala aquifer is present in only Todd County, and the Arikaree aquifer is present throughout most of Todd County and southwestern and south-central Mellette County. The Ogallala aquifer contains an estimated 17 million acre-feet of water in storage, and the Arikaree aquifer contains an estimated 50 million acre-feet of water in storage. Both aquifers generally are suitable for irrigation, and yields from these aquifers are sometimes greater than 1,000 gallons per minute. Nitrate concentrations in 13 out of 92 water samples collected from the Ogallala aquifer exceeded the Primary Drinking Water Maximum Contaminant Level (MCL) of 10 milligrams per liter. In 11 out of 46 samples collected from the Arikaree aquifer, arsenic concentrations exceeded the MCL of 50 micrograms per liter. The White River aquifer, where present, is usually the shallowest source of ground water in Mellette County. The White River aquifer also is used in northern Todd County where the Ogallala and Arikaree aquifers are not present. The White River aquifer contains an estimated 50 million acre-feet of water in storage. Reported yields from the aquifer range from 1 to 30 gallons per minute, which generally is insufficient to support irrigation in most areas. However, yields are sufficient for livestock-watering and rural-domestic purposes. In both counties, the Pierre Shale is the shallowest bedrock aquifer and is exposed at the land surface throughout most of Mellette County. This aquifer is used primarily in Mellette County. Although the aquifer contains an estimated maximum of 1.5 million acre-feet of water in storage, it is not a viable source of ground water because the aquifer is relatively impermeable, yields are low, and water usually can be obtained from shallower sources, especially in Todd County. Reported yields from the Pierre Shale aquifer range from 1 to 8 gallons per minute. Because few test holes and wells penetrate below the Pierre Shale, little is known about the extent of the deeper bedrock aquifers. All wells completed in the Dakota Sandstone, Inyan Kara, and Minnelusa and Madison aquifers in the counties are used for stock-watering purposes. High concentrations of dissolved solids and hard water are characteristic of the water quality in the bedrock aquifers. Depths to the top of the deeper bedrock aquifers range from 1,270 feet to greater than 2,000 feet below land surface.

South Dakota↗
USGS2026

Design and function of the Autonomous Benthic Imaging and Surveying System (ABISS) for remote sensing of lake and seabed environments

Lake and seabed environments are home to fisheries and other biota that are important to ecosystems and economies, yet these environments and the species that use them are difficult to accurately assess and monitor. Traditional benthic survey techniques, like bottom trawling used by the U.S. Geological Survey, are limited by substrate constraints, poor spatial resolution and precision, and operational depth limits, hindering accurate assessment of benthic species and habitats. In response to these limitations, the U.S. Geological Survey developed the Autonomous Benthic Imaging and Surveying System, a camera system integrated into underwater vehicles, to capture high-resolution images of the lakebed. The system uses color and stereo cameras to collect imagery, which can be analyzed using computational methods to detect organisms and (or) characterize habitat features, such as geologic substrate types. The system has been integrated into autonomous underwater vehicles and into an underwater housing used by self-contained underwater breathing apparatus (SCUBA) divers. Although the engineering of the system was motivated by the need for data collection in the Great Lakes, it has potential to collect high quality data in any aqueous setting with sufficient water clarity and safe operating conditions. The Autonomous Benthic Imaging and Surveying System can operate across diverse depths and light conditions to map and quantify ecological patterns that were difficult or impossible to assess using traditional methods. The Autonomous Benthic Imaging and Surveying System offers the potential for accurate and precise monitoring and assessment of native benthic biota, invasive species, and habitat, potentially providing natural resource managers with improved information to support decision making about benthic resource management.

Great Lakes↗
USGS2024

Are field observations of surface rupture useful? An example from the 2023 Mw 7.8 Pazarcık, Turkey (Türkiye), earthquake

Field investigations have long been an important component of the scientific response to surface‐faulting earthquakes. However, in light of advances in remote data and models, the question arises whether field‐based observations of surface rupture remain useful for understanding rupture processes and seismic hazards. We approach this question using a field‐based study of the central 2023 M w 7.8 Pazarcık, Turkey (Türkiye), earthquake rupture, at the intersection of the east Anatolian fault (EAF) and Narlı fault. Our field observations include the surface rupture expression and extent of the central EAF and northernmost Narlı fault in generally forested and steep terrain and 68 measurements of left‐lateral surface displacement. These data improve our understanding of the Pazarcık rupture complexity, resolve the surface geometry of the Narlı fault–EAF connection, and exhibit a clear (>2 m) change in surface displacement across this intersection zone that confirms remote‐based coseismic slip models. Our study shows that focusing field efforts in areas of obscured or low‐resolution remote data can yield essential data for refining rupture extent, documenting perishable on‐fault displacement, and improving postearthquake situational awareness. A comparison of similarly large‐magnitude continental surface‐rupturing earthquakes indicates that displacement uncertainties relate to a complex set of factors, including measurement methods, rupture complexity, and displacement magnitude. Our study validates the need for postearthquake field observations, which, when driven by clear motivating questions and knowledge of methodological strengths and limitations, provide high‐resolution rupture data that complement remote‐based models.

Pazarcık↗
USGS2025

System characterization report on the Environmental Mapping and Analysis Program (EnMAP)

This report addresses system characterization of the Environmental Mapping and Analysis Program hyperspectral sensor by the DLR (German Aerospace Center, ground segment project management), GFZ (Deutsches Geoforschungszentrum, science lead) and is part of a series of system characterization reports produced and delivered by the U.S. Geological Survey Earth Resources Observation and Science Cal/Val Center of Excellence. These reports present and detail the methodology and procedures for characterization; present technical and operational information about the EnMAP hyperspectral sensor; and provide a summary of test measurements, data retention practices, data analysis results, and conclusions. The Earth Resources Observation and Science Cal/Val Center of Excellence system characterization team completed data analyses to characterize the geometric (interior and exterior), and radiometric performances of the EnMAP hyperspectral sensor. Results of these analyses indicate that the Environmental Mapping and Analysis Program has a band-to-band geometric performance in the range of −0.135 to 0.15 pixel, geometric performance relative to the Operational Land Imager in the range of −27.716 meters (−0.92 pixel) to 32.892 meters (1.09 pixels) offset in comparison to Landsat 8 Operational Land Imager, offset of a radiometric comparison in the range of −0.012 to 0.020, slope of a radiometric comparison in the range of 0.947 to 1.031.

Open-File Report↗
USGS2024

California State Waters Map Series—Benthic habitat characterization in the region offshore Humboldt Bay, California

Coastal and Marine Ecological Classification Standard (CMECS) geoform, substrate, and biotic component geographic information system (GIS) products were developed for the California State Waters of northern California in the region offshore of Humboldt Bay. The study was motivated by interest in development of offshore wind-energy capacity and infrastructure in Federal waters offshore. This project, carried out by the U.S. Geological Survey (USGS), resulted in four data releases for individual map blocks that are part of the “California State Waters Map Series”: (1) Offshore of Arcata, (2) Offshore of Eureka, (3) Offshore of the Eel River, and (4) Offshore of Cape Mendocino. The study area consists of 436 square kilometers of multibeam echo sounder (MBES) data acquired by Fugro Pelagos, Inc., in 2007. Towed camera-sled video was acquired in 2009 and 2010 to supervise the classification of the MBES data into habitats, and single channel sparker data were collected to calculate sediment thickness above the transgressive unconformity. Using video observations of habitat as ground truth, derivatives of the MBES data were classified into 3 seafloor character types (hard-rugose, hard-flat, and soft-flat), 26 induration-slope-depth groups, and 15 geoforms. The study area substrate is predominantly soft-flat sediment (mud and fine sand) covering 73.6 percent of the area. Hard-flat substrate areas, predominantly coarse sediment in scour depressions, cover 5.4 percent of the study area. The hard-rugose substrate areas are primarily outcrops of layered sedimentary bedrock and constitute 20.9 percent of the study area. Fifteen geoforms were identified in the analysis. The predominant geoforms mirror the seafloor character results, shelf geoforms, rock outcrop geoforms, and scour depression geoforms. Rock and scour areas are restricted to the southern portion of the study area off Cape Mendocino where uplift has exposed bedrock. On the flat shelf area post-transgressive sediment varies in thickness from 1.7 meters (m) nearshore to 28.1 m offshore.

California↗
USGS2025

Foundational uncertainties in terminal Ediacaran chronostratigraphy revealed by high-precision zircon U-Pb geochronology of the Nama Group, Namibia

The Nama Group of southern Namibia and northwestern South Africa hosts the best-dated mixed carbonate-siliciclastic foreland basin succession of the terminal Ediacaran [ca. 551 million years (Ma) ago to <538 Ma] and is key for resolving the chronology of early metazoan evolution. Numerous silicified volcanic tuff interbeds are present, but differing interpretations regarding the fidelity of their ages lead to different regional stratigraphic correlations, especially for the Urusis Formation of the Schwarzrand Subgroup. An expanded record of the Urusis Formation is found in the Swartpunt area of southern Namibia, which has yielded an important metazoan biota. But the succession in this area is preserved as a series of thrusts at the leading edge of the Gariep orogenic belt and zircon U-Pb data show systematic age repetition. We use regional stratigraphic and structural mapping, integrated with carbonate carbon isotope (δ 13 C carb ) chemostratigraphy and high-precision radioisotope U-Pb zircon geochronology from outcrop and recently acquired drill core to develop a temporally calibrated basin-wide depositional model. This integrated dataset either reflects complex zircon reworking, inheritance, or potential analytical biases (Scenario 1) or the presence of a Gariep-related cryptic décollement within the Spitskop Member that has resulted in stratigraphic repetition (Scenario 2). We investigate the evidence for and against both scenarios and consider their implications for stratigraphic and δ 13 C carb correlations between the Swartpunt area and coeval exposures along the Orange River border with South Africa. Given that these issues are in an area that hosts numerous silicified ash beds and extensive exposure, an inability to confidently discount either scenario highlights a level of compounding uncertainty in zircon U-Pb geochronology that must be considered when attempting to build global chronostratigraphic frameworks. Scenario 1 implies that some of the weighted mean ages and Bayesian eruption ages from the Swartpunt area may be >1 Myr older than the depositional age of their respective ash beds when assuming existing stratigraphic correlations. If this scenario is preferred, then a cautious approach would be to consider all weighted mean zircon U-Pb ages from ash beds to reflect maximum depositional ages. Both scenarios support deposition of the Huns Member >540 Ma in the Swartpunt area if the oldest weighted mean age reported here represents a near-depositional age, which has significant implications for the temporal calibration of important terminal Ediacaran ichnofossil assemblages and future cyclostratigraphic studies. Stratigraphic correlations common to both scenarios allow us to temporally calibrate a basin evolution model for the Nama Group. Temporal trends in initial hafnium isotope (εHf) compositions of zircon grains from ash beds throughout the succession may support progressive crustal thickening associated with underplating of the Damara orogenic belt along the northern periphery of the Kalahari craton from ca. 547 Ma to ca. 538 Ma. The compilation of new and published zircon U-Pb ages may also imply that the locus of carbonate platform development migrated from north to south (present co-ordinates), tracking the migration of foredeep subsidence.

Earth-Science Reviews↗