USGS Science⌕ Search

SEARCH · USGS Science

Results for “New Zealand Journal of Geology and Geophysics”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,689 records · Page 37Linked to original sources
USGS2025

Evolution of permeability and strength recovery of shear fracture under hydrothermal conditions

Geothermal energy is a clean and renewable resource that depends on the ability to move water through hot rock. In many locations, the ability to move water through rock requires the presence of extensive natural or human-made systems of fractures. However, these fracture systems are influenced by a variety of complex processes that occur at the temperature and pressure conditions found in geothermal reservoirs. To make geothermal systems more efficient, it is important to understand how these fractures evolve over time in response to these processes. This study explored how fractures in rock change under high-temperature and pressure conditions, like those found in geothermal reservoirs, through laboratory experiments and numerical simulations. In general fractures, tend to close due to pressure from the surrounding rock preventing the flow of water. One set of laboratory experiments revealed that fractures in granitic rock can weaken over time at elevated temperatures. These weak fractures can then slip slowly potentially keeping the fracture open for a longer period. This study also showed that at the highest temperature examined (250 °C) large differences between the chemical composition of the rock and the fluid moving through it could improve water flow temporarily likely due to the water dissolving parts of the rock. Flow rate predicted by models shows overall good agreement with the flow rate measured in our experiments but with some long time-scale variations that may be due to mechanical wear of the fracture surface. A second set of experiments found that, over the temperature range examined, the closure of fractures was caused by brittle failure driven by high stresses at points where fracture surfaces were in contact. This result suggests that fracture closure in geothermal reservoirs could be counteracted by maintaining high pore pressures. Additionally, we also tested a new method using electrical resistance to measure fracture closure in controlled systems with high precision.

Final Technical Report↗
USGS2025

A newly identified creeping strand of the Concord fault, San Francisco Bay Area

The Concord fault constitutes a major branch of the Pacific–North America transform plate boundary in Northern California, bridging the strike‐slip Bartlett Springs ‐ Green Valley Fault system to the north with the Greenville and Calaveras Faults to the south. Like many faults in the San Francisco Bay Area its long‐term slip is partially accommodated by aseismic slip (creep). Although creep has been recognized and monitored on the northern half of the fault for decades, the precise location of the southern half of the fault and its slip rate—whether accommodated seismically or aseismically—has remained enigmatic. How slip transfers between the Concord and Greenville or Calaveras faults to the south remains an outstanding question. New field observations presented here indicate that the active trace of the fault south of downtown Concord is not where previously interpreted and is indeed actively creeping. We report observations of shallow creep continuing >7 km farther south along the Concord fault than previously reported, along a fault strand not previously recognized for most of its length. This is evident as right‐laterally deflected concrete curbs and sidewalk slabs on both sides of every street that crosses the fault at a high angle in southeast Concord and northeast Walnut Creek. We document the magnitude and location of these deflections to estimate accumulated right‐lateral aseismic slip expressed in engineered structures. Offsets of these piercing lines range from 8 to 18 cm, over widths varying from narrow breaks along centimeter‐scale concrete joints to 10‐m‐wide zones of deflection. Significantly, this active trace is ∼400 m west of where the Quaternary active trace has previously been inferred, placing it within—rather than bounding—the built area of suburban Concord. Slip along the fault has already caused infrastructure damage. These results revise our understanding of the southern Concord fault and help constrain its seismic potential.

California↗
USGS2025

Seismic response of rock towers at the Trona Pinnacles (U.S.A.) to the 2019 Ridgecrest earthquake sequence: Theory, observations, and models

We analyze the seismic response of a class of fragile geologic features (FGFs), referred to as rock towers (RTs) at the Trona Pinnacles, a group of RTs in southern California that suffered strong shaking during the 2019 Ridgecrest earthquake sequence. FGFs, including RTs, may provide maximum constraints on past earthquake shaking intensity, and thereby support probabilistic seismic hazard assessments (PSHAs). In a rare case study, we explore the hypothesis that RT structural integrity is time dependent, as damage accumulates progressively. We develop finite‐element method (FEM) models of the RTs using photogrammetric shape models. We validate the models by comparing numerical simulations of their response to broadband ground shaking with low‐intensity seismic recordings obtained at the Pinnacles. Results of our simulations are in good agreement with the seismic recordings of actual earthquake aftershocks. We next use the results of the FEM models to analyze the response and evolution of RTs. Our analyses elucidate the influence of geometry over their seismic response, providing a rationale that may explain the rarity of slender RTs at Trona: high‐aspect‐ratio structures that respond in bending develop detrimental tensile stresses that crack the rock, whereas low‐aspect‐ratio ones’ response also includes shearing, which does not compromise material integrity as much as tension. Field measurements with a rebound hammer support this finding, suggesting that the material around the base of slender rocks has been weakened relative to other parts of the RT. We also study how to define simplified mechanical models (“archetypes”) to predict the natural frequencies of RTs. Results from our work illuminate the fundamental mechanisms of seismic response and progressive failure of RTs, and open new avenues of research to potentially incorporate these geologic features as long‐return period constraints on PSHA, in ways analogous to those of the widely used precariously balanced rocks.

California↗
USGS2026

Evaluating groundwater quality influences from oil field operations and other anthropogenic activities in an urban setting, Santa Fe Springs, California

Groundwater quality is often affected by anthropogenic activities in urban settings. This study examines groundwater quality in and around the Santa Fe Springs Oil Field in Los Angeles County, California, where oil and gas production commonly intersects with high density industrial, commercial and residential land uses. Utilizing a combination of new and historical data, we evaluated potential pathways that would allow for oil field formation fluids to migrate into groundwater and whether mixing may have occurred based on the distribution of groundwater and oil field formation fluid tracers in samples. Samples were analyzed for a wide array of constituents including volatile organic compounds, light hydrocarbons, major ions, and various isotopic compositions. Despite evidence of oil field infrastructure providing potential pathways of migration via uncemented annular spaces, casing breaches and historical disposal of oil field formation water in surface ponds, the distribution and occurrence of stable isotopes of water, chloride, boron, and total dissolved solids do not indicate mixing of oil field formation water and groundwater. However, methane isotopic signatures and the presence of heavier alkanes suggest gas from oil-bearing formations have migrated from depth via oil field well infrastructure. Volatile organic compound detections were mainly from manufactured compounds unrelated to oil and gas production, with a relatively limited number of petroleum hydrocarbons also detected. Volatile organic compounds were generally found in wells tapping shallow, modern aged groundwater, indicating anthropogenic activities occurring at or near land surface as the source. Study results suggest that while oil field infrastructure provides migration pathways for oil field formation fluids to be introduced into groundwater, urban land uses not related to oil and gas production are the primary drivers of groundwater quality degradation.

California↗
USGS2024

Seismic techniques and suggested instrumentation to monitor volcanoes

Introduction Changes in the pressure or location of magma can stress or break surrounding rocks and trigger flow of nearby waters and gases, causing seismic signals, such as discrete earthquakes and tremor. These phenomena are types of seismic unrest that commonly precede eruption and can be used to forecast volcanic activity. Mass movements at the surface, including avalanches, debris flows, and lahars, may also generate seismic signals that are specifically addressed in chapter H , this volume (Thelen and others, 2024). Our focus in this chapter is to determine the levels of instrumentation recommended to produce high-quality, well-constrained seismic observations important for early warning of impending eruptions, detecting changes in ongoing eruptions, and characterizing other hazardous volcanic events. There are emerging techniques and new types of instrumentation, such as distributed acoustic sensing or rotational seismometers, that we do not consider here. These types of instrumentation show promise for monitoring but still require maturation before being considered more generally in volcano monitoring. Most of the capabilities mentioned below are universal for all types of volcanic systems, although some are best applied to stratovolcanoes with an apical single vent. In some settings, such as calderas or shield volcanoes, we must broaden coverage to include multiple possible storage regions or vent locations. As an example, Thelen (2014) discretized the long rift zones of shield volcanoes in Hawaiʻi as a set of evenly spaced “vents.” In this construct, each vent comes with recommendations, and several thousand network configurations were simulated to assess the effect on network quality levels and to determine the most efficient network design. The same process could be applied in a caldera setting or a volcanic field, where an evenly spaced grid of potential vents is considered. Localized recommendations for each unique system are beyond the scope of this report and left up to local experts to assess based on the conditions, restrictions, and requirements of each volcano.

Scientific Investigations Report↗
USGS2024

Produced water geochemistry from hydraulically stimulated Niobrara Formation petroleum wells: Origin of salinity and temporal perspectives on treatment and reuse

Produced water (i.e., a mixture of returned injection fluids and geologic formation brines) represents the largest volumetric waste stream associated with petroleum production in the United States. As such, produced water has been the focus of intense study with emphasis on understanding the geologic origin of the fluids, environmental impacts of unintended or intentional release, disposal concerns, and their commodity (e.g., lithium) potential. However, produced water geochemistry from many active petroleum plays remain poorly constrained leading to knowledge gaps associated with the origin of brine salinity and parameters (e.g., radium levels) that can impact treatment, disposal, and possible reuse. Here we evaluate the major ion geochemistry, radium concentrations, and stable water isotope composition of ~120 produced water samples collected from 17 producing unconventional petroleum wells in Weld County, Colorado from the Late Cretaceous Niobrara Formation. This sample set encompasses eight produced water time series from four new wells across production days 0 to ~365 and from four established wells across production days ~1000 to ~1700. Additionally, produced water from nine other established Niobrara Formation wells were sampled at discrete time points ranging from day 458 to day 2256, as well as hydraulic fracturing input fluids. These results expand the available Niobrara Formation produced water geochemical data, previously limited to few wells sampled within the first year of production, allowing for the heterogeneity of major ions and radium to be evaluated. Furthermore, we explore the geochemical relationships between major ion ratios and stable water isotope composition to understand the origin of salinity in Niobrara Formation brines from the Denver-Julesburg Basin. These findings are discussed with perspective toward potential treatment and reuse of Niobrara produced water prior to disposal.

Colorado, Nebraska, Wyoming↗
USGS2024

Coastal Science Navigator companion guide—Discover the U.S. Geological Survey coastal science products you need

The Coastal Science Navigator is an online gateway to a wide variety of U.S. Geological Survey (USGS) coastal change hazards-related information, data, and tools relevant to stakeholders’ scientific and decision-making needs. The products within the Coastal Science Navigator provide data related to past, present, and future threats to our coastlines. The filter search allows users to see all available products and identify relevant options by time scale, geographic scope, coastal hazard theme, and other filters. The guided search suggests products based on users’ answers to a short series of questions. A comprehensive summary is available for each product. The idea for the Coastal Science Navigator arose in 2020 in response to stakeholder feedback identifying the need for a central source for USGS coastal science information. It was published in July 2023 and initially included 55 products. Regular updates are planned to integrate other existing and new products. This guide introduces some of the many coastal change hazards-related products available through the USGS. In it, we showcase the products included in the Coastal Science Navigator’s initial publication in July 2023. While it is not representative of all the information, tools, and data available, we hope it serves as a compelling snapshot of what the USGS has to offer and encourages you to explore the Coastal Science Navigator to discover more of the products you need. To navigate this guide, the products have been organized by the time scale they are best suited for—past, present, or future—although many products cover multiple time scales. An additional section features software, one of the many product types available as filters within the Coastal Science Navigator. Other products include downloadable data, websites, and geonarratives (web pages that combine text, images, and interactive maps into narratives you can scroll through). Featured geographic scopes are also highlighted within this guide, detailing some of the many regions in which the USGS conducts research and illustrating another way to filter products within the Coastal Science Navigator.

Circular↗
USGS2025

Assessment of western Oregon debris-flow hazards in burned and unburned environments

In the steep and mountainous environment of western Oregon, debris flows pose a considerable threat to property, infrastructure and life. Wildfire is commonly known to increase the susceptibility of steep slopes to debris flows, but the extent of this process in the western Cascades is not well understood. The US Geological Survey (USGS) currently estimates postfire debris-flow likelihood and triggering rainfall thresholds using a model calibrated to a southern California inventory of debris flows generated by excess runoff within the first year after fire. Because of a lack of available data, this model has not been tested in western Oregon, or in locations where postfire debris flows initiate via other mechanisms (e.g., shallow landslides or in-channel failures). Using repeat field observations and aerial imagery, we developed two new debris-flow inventories within and adjacent to the perimeters of five 2020 wildfires in western Oregon: Archie Creek, Holiday Farm, Beachie Creek, Lionshead and Riverside. The first inventory focuses on postfire debris flows (2020–2022); the second focuses on debris flows prior to fires (1995–2020). Our inventories of prefire and postfire debris flows were used to document initiation mechanisms in Oregon's western Cascades and to evaluate the effects of wildfire. We found that wildfire changed the distribution of debris-flow initiation mechanisms in the western Cascades. After the wildfires, annual rates of runoff-generated debris flows increased by 22% and the number of shallow landslide-initiated debris flows decreased by 17% relative to before the wildfires. Despite this shift, shallow landsliding was the dominant debris-flow initiation mechanism in both unburned and burned environments. We found the performance of the current USGS debris-flow likelihood model was degraded relative to other previously tested locations across the intermountain western United States. Our results highlight the need for improved postfire hazard assessment in western Oregon based on regional model calibration that is tuned to the dominant debris-flow initiation mechanisms.

Oregon↗
USGS2025

Capturing the uncertainty of seismicity observations in earthquake rate estimates: Implications for probabilistic seismic hazard analysis and the USGS National Seismic Hazard Model

The rate of earthquakes in a region is a fundamental input to Probabilistic Seismic Hazard Analysis. We present a Monte Carlo method for computing that rate from seismicity catalogs while including a range of data and analysis uncertainties. This method is applied to regions for which the b value is assumed to be spatially invariant. Each region is broken down into epochs for which each epoch is estimated to have a uniform magnitude of completeness ( ⁠⁠ M c ). The distribution of earthquake rates for M ≥ M c is determined for each epoch by considering the Poisson likelihood of rates given the number of observed earthquakes with M ≥ M c ⁠ . We use a Monte Carlo process to include the uncertainty in b , ⁠ M c , and individual event magnitudes. The result for each epoch is the joint distribution of the Poisson rate of earthquakes with magnitudes larger than the minimum value used to calculate hazard ( ⁠⁠ M 1 ) and the Gutenberg–Richter b values, which control the extrapolation to other magnitudes. The rate for each region is either the duration‐weighted average over the epochs or, to better capture temporal variations, we also consider mixture models. The mixture models also provide an avenue to allow temporal variations in b values. To implement this joint distribution in a logic tree, we use the mean and 95% confidence branches, each of which is parameterized with an M ≥ M 1 rate and b value. We explore different ways of defining those branches, as well as non‐Gutenberg–Richter branches, and their impact on hazard estimates. The mean hazard, but not the fractiles, is robust with respect to these choices. To illustrate these new methods, we use synthetic data and catalogs from recent U.S. Geological Survey National Seismic Hazard Models for the Central and Eastern United States and for Puerto Rico and the U.S. Virgin Islands.

central and eastern United States, Puerto Rico, U.↗
USGS2023

Sediment thickness map of United States Atlantic and Gulf Coastal Plain Strata, and their influence on earthquake ground motions

With the recent successful accounting of basin depth ground-motion adjustments in seismic hazard analyses for select areas of the western United States, we move toward implementing similar adjustments in the Atlantic and Gulf Coastal Plains by constructing a sediment thickness model and evaluating multiple relevant site amplification models for central and eastern United States seismic hazard analyses. We digitize and combine existing sediment thickness data sets into a composite surface that delineates the base of Cretaceous sediments under the Atlantic Coastal Plain and the base of Mesozoic sediments under the Gulf Coastal Plain. Amplification models dependent on sediment thickness, site natural period, and source-to-site path length are compared with data sets of observed ground motions to evaluate the ability of the new models to improve ground motion estimates. We find that the amplification models can account for observed trends in sediment-thickness and period-dependent residuals, but some tuning is required. For example, the model of Chapman and Guo requires a reference V S 30 , the time-averaged shear-wave velocity within 30 m of the Earth’s surface, for non-Coastal Plain sites, which we estimate to be between about 1 and 2 km/s. Along with our sediment thickness model, we estimate a velocity profile for application to the Harmon et al. site-natural-period-based model in order to best match the Chapman and Guo period dependence for a broad range of sediment thicknesses. The Next Generation of Attenuation models for the eastern United States Gulf Coast path-based adjustment models can also account for seismic attenuation in the Coastal Plain sediments and reduce the standard deviation of total residuals. If enacted in the U.S. Geological Survey National Seismic Hazard Model, these amplification models will reduce predicted short-period (<1 s) and increase predicted long-period (>1 s) ground motions in the Coastal Plains appreciably.

Earthquake Spectra↗
USGS2024

Comparing subduction ground-motion models to observations for Cascadia

We evaluate Cascadia subduction ground-motion models (GMMs), considered for the 2023 US National Seismic Hazard Model (NSHM) update, by comparing observations to model predictions. The observations comprise regional recordings from intraslab earthquakes, including contributions from 2021 and 2022 events in southern Cascadia and global records from interface earthquakes. Since the 2018 NSHM update, new GMMs for Cascadia have been published by the Next Generation Attenuation (NGA)-Subduction Project that require independent evaluation. In the regional intraslab comparisons, we highlight a characteristic frequency dependence for Cascadia data, with short periods having lower ground motions and longer periods being comparable to other subduction zones. We evaluate differences in northern and southern Cascadia and find that the NGA-Subduction GMMs developed using southern Cascadia data perform better in this region than the model that did not consider these data. We compare ground-motion variability in Cascadia with the NGA-Subduction model predictions and find differences at short periods ( T = 0.1 s) due to the use of global versus regional data in the development of these models. Moreover, the within-event component of aleatory variability from the GMMs overpredicts the standard deviation of Cascadia recordings at very short periods ( T < 0.05 s). Using global interface earthquakes as a proxy to evaluate the Cascadia GMMs, we find long-period overprediction from a simulation-based GMM and some of the empirical GMMs. When comparing recent observations, we find a similar misfit to GMMs and the 2010 and 2022 Ferndale earthquakes. Finally, we observe different basin amplification factors arising in different subsets of the data, which indicate that differences in basin factors between empirical GMMs could arise from the data selection choices by the developers. As part of evaluating the regional basin terms, we apply basin amplification factors from the magnitude 9 Cascadia earthquake simulations to the empirical GMMs for interface earthquakes. The comparisons presented in this study indicate that the NGA-Subduction GMMs for Cascadia perform well relative to observations and older subduction GMMs.

British Columbia, California, Oregon, Washington↗
USGS2026

Vegetation cover and composition in environments surrounding uranium mines in the Grand Canyon ecosystem, Northern Arizona

Mining uranium from breccia-pipe deposits in the greater Grand Canyon region has occurred since the mid-1900s. However, possible ecosystem contamination with harmful levels of radionuclides may have occurred due to mining activities in the 21st century. In response, a 20-year Federal moratorium on new mining claims in the Grand Canyon watershed was initiated in 2012, to allow time to evaluate the potential effects of uranium exploration and mining on human health, wildlife, and water resources. This moratorium, nor the 2023 designation of the “Baaj Nwaavjo I’tah Kukveni–Ancestral Footprints of the Grand Canyon National Monument,” precludes operation or development of mining claims predating 2012. Vegetation is a core ecosystem component that may be affected by uranium mining (for instance, through uptake and storage of radionuclides from the air or soil) or may act as a vector of exposure to wildlife, livestock, and humans (for instance, via their consumption of contaminated plant tissues). To provide baseline information about the plant communities associated with uranium mines in the Grand Canyon region, the U.S. Geological Survey surveyed an approximately 200-meter-wide buffer surrounding four breccia-pipe deposits, each in a unique stage of mine development, and at one reference area (a livestock water tank) that underwent ground disturbance but contains no mineral deposits. We sectioned the buffer zones into 0.65–4.52 hectare plots, within which we (1) inventoried all plant species, (2) measured percent cover of plant species, plant functional groups, and ground surface types (dark cyanobacteria, lichen, moss, bedrock, rock, embedded litter, duff, plant bases, and bare soil) using line-point intercept, and (3) measured length and frequency of gaps between perennial plant canopies using canopy gap intercept. We found that plant composition at the mines and the reference area differed from one another but were all characteristic of expected regional vegetation patterns. We provide this data summary as potential baseline information for future research and management efforts.

Arizona↗
USGS2024

Assessment of fresh groundwater discharge and saline surface-water intrusion at Operable Unit 2, North Chevalier Field Disposal Area (Site 11), Naval Air Station Pensacola, Florida, 2018–22

Site 11 is a former landfill at North Chevalier Field Disposal Area in Operable Unit 2 at Naval Air Station Pensacola, in northwest Florida. Site 11 is adjacent to Bayou Grande, a shallow, tidally influenced, saline estuary of the Pensacola Bay watershed. Federal and Florida regulators have expressed concern that contaminants detected in groundwater beneath the inland parts of Site 11 may discharge to Bayou Grande. In 2017, the Department of Defense, U.S. Navy, Naval Facilities Engineering Systems Command Southeast asked the U.S. Geological Survey to assess the occurrence of fresh groundwater discharge to Bayou Grande at Site 11 and to delineate to the extent practicable the location of groundwater discharge. Between 2018 and 2022, the U.S. Geological Survey used a multiple-lines-of-evidence approach that included a visual method and three physical methods based on the temperature difference between groundwater and surface water to assess groundwater discharge. One of the physically based methods also used the difference in specific conductance between fresh groundwater and brackish to saline surface water. Combined, the data indicate that fresh groundwater from across Site 11 discharges primarily along the shoreline of the northern and northeastern part of Site 11. The data also indicate that saline surface water from Bayou Grande intrudes tens of feet into the shallow aquifer beneath Site 11. The combined data indicate that the interface between fresh groundwater and saline surface water changes over space and time. Any new monitoring wells proposed for installation near the shoreline of Site 11 should include approaches to monitor the changes in the location of the freshwater/saltwater interface. Care would need to be taken to collect any groundwater samples at the correct season and tidal period to provide the highest probability of collecting a representative sample of Site 11 groundwater unaffected by saltwater.

Florida↗
USGS2025

Hydrogeologic investigation, framework, and conceptual flow model of the Antlers aquifer, southeastern Oklahoma, 1980–2022

The 1973 Oklahoma Groundwater Law (Oklahoma Statute §82–1020.5) requires that the Oklahoma Water Resources Board conduct hydrologic investigations of the State’s groundwater basins to support a determination of the maximum annual yield for each groundwater basin. Every 20 years, the Oklahoma Water Resources Board is required to update the hydrologic investigation on which the maximum annual yield determinations were based. The maximum annual yield allocated per acre of land is used to set the equal-proportionate share pumping rate. The maximum annual yield of 5,913,600 acre-feet per year and equal-proportionate-share of 2.1 acre-feet per acre per year currently (2025) in place for the Antlers aquifer were issued by the Oklahoma Water Resources Board on February 14, 1995. Because more than 20 years have elapsed since the 1995 final order for the Antlers aquifer was issued, the U.S. Geological Survey, in cooperation with the Oklahoma Water Resources Board, completed an in-depth hydrologic study that included a hydrogeologic framework and conceptual groundwater-flow model for the 1980–2022 study period. The results of an analysis of land use, long-term climate patterns, streamflow and base-flow patterns, historical groundwater use, as well as groundwater-level fluctuations across the Antlers aquifer are described. In addition, groundwater quality was analyzed for total dissolved solids concentrations and major ions for the Antlers aquifer. An updated hydrogeologic framework was developed that included refining the aquifer boundary in Oklahoma, the creation of new potentiometric surface and saturated thickness of fresh groundwater maps, one multiple-well aquifer test, slug tests, and an analysis of lithologic logs across the aquifer. A conceptual groundwater flow model and water budget were developed by incorporating estimates of recharge from precipitation, saturated-zone evapotranspiration, streambed seepage, lateral groundwater flows, vertical leakage, and withdrawals from groundwater wells.

Oklahoma, Texas↗
USGS2025

Broadband stochastic simulation of earthquake ground motions with multiple strong phases with an application to the 2023 Kahramanmaraş, Turkey (Türkiye), earthquake

Stochastic ground motion simulation models are often less accurate at lower frequencies than at higher frequencies when fitting recorded data unless supplemented by a deterministic forward directivity velocity pulse model. Moreover, time-modulated stochastic models, which adjust ground motion amplitudes over time, typically use functions that fail to capture multiple strong-motion phases. The February 2023 Turkey (Türkiye) earthquake exhibited diverse recordings, including near-fault and far-field motions with pulse-like and non-pulse-like characteristics, along with single and multiple strong-motion phases. To better represent such a diverse set of recordings, this study enhances a fully non-stationary site-based stochastic model without combining it with a deterministic model. Improvements include a new band-pass filter with upper- and lower-frequency limits, which refines the representation of the low-frequency content. Moreover, a time-modulating function that can represent energy arrival in multiple strong phases is introduced. The reference model’s parameters are identified by fitting to the energy content, zero-level crossings, and cumulative counts of positive-minima and negative-maxima of a target accelerogram. This fitting procedure is modified to address the increased number of parameters. These improvements broaden the reference model’s applicability while preserving its simplicity, a key aspect appealing to engineering practitioners. The improved model’s applicability is demonstrated by simulating a dataset from the February 2023 Türkiye earthquake, and the accuracy is tested using a pulse-like Next Generation Attenuation Relationships for Western United States dataset. Validations are performed based on total energy, zero-level crossings, Fourier amplitude spectrum, elastic response spectra, and peak ground motion parameters. Validations are performed schematically in the time and frequency domains and quantitatively using goodness-of-fit scores, various validation-metrics errors, and inter-period correlations. Overall, the improved stochastic model can effectively simulate a set of diverse ground motion recordings, including near-fault pulse-like records, records with multiple strong phases, and far-field motions across a broad frequency range.

Kahramanmaraş↗
USGS2025

Groundwater hydrology, groundwater and surface-water interactions, water quality, and groundwater-flow simulations for the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado, 2017–19

In 2017, the U.S. Geological Survey, in cooperation with the Upper Arkansas Water Conservancy District, began a study to provide a comprehensive analysis of the Wet Mountain Valley alluvial aquifer, Custer and Fremont Counties, Colorado. The study included collection of data pertaining to groundwater hydrology, groundwater and surface-water interactions, and water quality in the alluvial aquifer. In addition to providing foundational information on the hydrology of the alluvial aquifer, a numerical groundwater-flow model was developed to estimate the potential effects of additional storage of groundwater in the alluvial aquifer. Groundwater-level elevation data from 30 wells were used to estimate groundwater-flow directions in the alluvial aquifer, which were generally from the southwest to northeast, away from the Sangre de Cristo Mountains and towards perennial streams in the center of the valley. Although some seasonal variation was apparent in groundwater-level elevation records, no statistically significant seasonal trends were indicated. Statistically significant long-term trends were indicated in groundwater-level elevation records for 8 of the 30 wells, and of these wells with statistically significant trends, all but 1 indicated a negative trend of groundwater-level elevations. Spatial evaluation of wells with statistically significant negative groundwater-level elevation trends showed many are in areas of denser well drilling for domestic or other uses, indicating increasing groundwater use could potentially be causing groundwater-level elevation declines. There were instances of wells with no statistically significant groundwater-level elevation trends also located in areas of greater density of well completions. Additional investigations may be necessary to more fully characterize the processes responsible for negative groundwater-level elevation trends. Streamflow gain or loss calculations were completed for low flow in 2017–19 and for high flow in 2018 in nine reaches of streams within the study area. Stream reaches of the upper Texas Creek, upper Grape Creek, upper-middle Grape Creek, and Taylor Creek displayed consistent streamflow loss in each period from 2017 to 2019. These stream reaches represent long-term sources of recharge to the alluvial aquifer. Streamflow gain or loss varies through time in other stream reaches (lower Texas Creek, lower-middle Grape Creek, lower Grape Creek below Westcliffe, and lower Grape Creek above DeWeese Reservoir). The temporally variable behavior indicates these stream reaches may be sources of groundwater recharge or areas of groundwater discharge, likely depending on temporal dynamics between the elevation of the water table and the stream. Water-quality samples were collected from 10 groundwater wells and 10 stream sites during September through November 2019. All groundwater and stream samples were analyzed for major and trace elements and stable isotopes of water. A subset of groundwater samples was also analyzed for the environmental tracers sulfur hexafluoride, tritium, and noble gases. Comparison of water-quality results to U.S. Environmental Protection Agency drinking water-quality standards indicated no constituents exceeded primary standards for human health. Spatial evaluation of water quality indicated the concentrations of various constituents are likely controlled by groundwater and surface-water interactions and by spatial variability in bedrock geology underlying the alluvial aquifer. Specifically, streams shown to gain from groundwater had water chemistry constituent compositions similar to groundwater, whereas streams exiting the Sangre de Cristo Mountains tended to have compositions consistent with snowmelt. Groundwater geochemistry appeared to be partially controlled by oxidation-reduction processes and by proximity to igneous rocks in the Wet Mountains. Environmental tracers used to estimate groundwater age indicated all sampled groundwater contained tracers representing modern recharge (approximately less than 65 years old) but mixing of premodern recharge (approximately more than 65 years old) also occurs. Spatial evaluation of environmental tracers indicated large faults may be conduits for upwelling of older groundwater. No trends were observed in groundwater age with well depth, indicating all sampled wells are located within the zone of active groundwater flow. The presence of modern groundwater in wells with statistically significant negative groundwater-level elevation trends indicates groundwater storage depletions may be partially offset by capture of modern recharge. Repeated sampling of groundwater age would be necessary, however, to determine if any trends in groundwater age exist, which may indicate changing groundwater recharge, storage, or discharge. Additional investigations could also consider quantifying groundwater age in deeper wells to more fully define the depth of active groundwater flow. A numerical groundwater-flow model was developed to estimate components of the water budget, simulate groundwater and surface-water interactions, and evaluate the potential effects of aquifer storage and recovery. Simulated groundwater-level elevations from the calibrated groundwater-flow model are similar to the observed pattern of groundwater-level elevations with higher elevations in the western part of the study area along the Sangre de Cristo Mountains. Simulated water-budget components indicate most of the recharge to the alluvial aquifer is derived from streamflow losses, which is consistent with observations of losing streams along the mountain front. The largest groundwater discharge component of the alluvial aquifer was to streams in the center of the valley, where observations of stream gain or loss indicated the predominance of gaining conditions. Comparison of groundwater and surface-water interactions between the calibrated groundwater-flow model for 2000-19 (the base-case model) and a simulation including additional recharge, representing potential aquifer storage and recovery operations, indicated the additional recharge distributed throughout the area had minimal effects on streamflow in the nearby Grape Creek. An analysis of subregional groundwater budgets showed approximately 54 percent of the additional recharge flowed back to nearby Grape Creek, and the other 46 percent was distributed laterally into adjacent cells in the alluvial aquifer. The comparison of simulations and subregional water budget show the additional recharge did not substantially alter groundwater-level elevations or basin wide groundwater storage. Although the analysis of additional recharge provided in the numerical groundwater-flow model considers only one of many possible recharge scenarios, the model provides a useful tool that could be modified for various scenarios to understand potential effects of managed aquifer recharge.

Colorado↗
USGS2026

Bathymetric survey and storage capacity of Upper Lake Mary near Flagstaff, Arizona in 2024

The U.S. Geological Survey (USGS), in cooperation with the city of Flagstaff, collected bathymetric, light detection and ranging (lidar), and land-survey data of Upper Lake Mary in Arizona during the months of April and October 2024. The city of Flagstaff uses a combination of groundwater from well fields throughout the Flagstaff area and surface water, mainly from Upper Lake Mary, for its potable water supply. The purpose of the survey is to update previous surveys using new technology and compare the results to previous surveys to determine if there was a decrease in storage capacity that could affect the city’s water supply. The lakebed was mapped in April 2024 using a vessel equipped with a multibeam echosounder (MBES) and mobile lidar scanner with positioning captured using a real-time kinematic global navigation satellite system (RTK GNSS) base and receivers. In October 2024, areas of the reservoir that were too shallow for the boat and shoreline that were not captured by the vessel-based lidar were surveyed on foot using hand-held RTK GNSS receivers. At full pool (spillway elevation of 6,831.82 feet above NAVD 88 [2,082.34 meters (m)], Upper Lake Mary has a storage capacity of 16,449.80 acre-feet (20,290,611.73 cubic meters) and a surface area of 953.57 acres (3,860,926.075 square meters). The reservoir is 5.7 miles (9.7 kilometers) long and varies in width from 326 feet (99.36 m) near the central, narrow portion of the reservoir to 2,613 feet (796.44 m) in the upper portion. Comparisons between this survey and the previous two surveys from the 1950s and 2006 indicate no apparent decrease in reservoir area or storage capacity. Results of the 2024 survey indicate that Upper Lake Mary’s storage capacity increased by 0.9 percent from the 2006 survey and a 1.6 percent increase in surface area from the 2006 survey.

Arizona↗
USGS1976

Availability of ground water in the area surrounding the Trident submarine construction facility, Kitsap County, Washington

This report provides general information on the water resources--with emphasis on ground-water occurrence and availability--in that part of Kitsap County (referred to as Trident Impact Area) that would be most affected by the development of the Trident submarine-construction facility at Bangor. Ground water occurs principally in a lower, confined aquifer near and below sea level and an upper, unconfined aquifer above sea level; both aquifers are extensive beneath the study area and are composed of sand and gravel layers separated by poorly permeable silt, clay, and till layers. Locally throughout the area efficiently constructed wells tapping each of the two aquifers are capable of yielding 100 to 1,300 or more gallons per minute. The estimated 1970 water use in the study area averaged about 13 million gal/day (gallons per day); of this amount about 9 million gal/day came from surface-water sources--from a large reservoir outside the study area--and about 4 million gal/day came from ground water pumped from the two aquifers. Anticipated water use soon will be about 18 to 21 million gal/day; virtually all the additional quantity required (about 5 to 8 million gal/day) above present use must come from ground-water sources. Preliminary evaluation of the aquifers suggests that an additional 1.5 million gal/day can be developed from the upper aquifer and 7 million gal/day from the lower aquifer. Existing wells tapping the lower aquifer might yield additional water and increase the total yield in the area by 3.5 million gal/day, and new wells drilled in selected areas could produce an additional 3.5 million gal/day from this aquifer. However, additional, large-scale ground-water withdrawal from the lower aquifer could induce saltwater intrusion into wells situated in coastal areas. Recommended future studies include additional data collection, monitoring of chloride concentrations in water from large-yield coastal wells, confirmation of well yields and capacities, and test-well drilling and analysis.

Washington↗