SEARCH · USGS Science

Results for “Frontiers in Marine Science”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,606 records · Page 37Linked to original sources

USGS2025

Factors affecting the distribution of water-bearing fractures in the bedrock aquifers of West Virginia

Bedrock aquifers cover 23,601 square miles within the State of West Virginia and comprise 97.4 percent of the surficial area within the State; the remaining 2.6 percent (621 square miles) consists of alluvial sand-and-gravel and glacial outwash aquifers bordering the State’s major rivers. While West Virginia’s alluvial aquifers have been studied extensively, bedrock aquifers have only been characterized for studies completed in a few areas in Jefferson, McDowell, and Monroe Counties. Bedrock aquifers are water supplies for public supply, agriculture, industry, and residential homeowner use. In this study, the U.S. Geological Survey, in cooperation with the West Virginia Department of Environmental Protection Division of Water and Waste Management, provides a statewide assessment of the occurrence and distribution of fractures within bedrock aquifers of the State and the various topographic, physiographic, and lithologic influences controlling the occurrence and distribution of bedrock fractures. The results of this study provide an increased understanding of the distribution of fractures in bedrock aquifers in West Virginia and help to verify trends that have been suspected for many years but were never well documented or verified by data. The results confirmed that the density of fractures and those that were determined to be water bearing decrease significantly with depth. A statistically significant difference in the density of fractures was observed at a depth of 215 feet for wells in the Appalachian Plateaus Physiographic Province’s and in the Valley and Ridge Physiographic Province’s aquifers; a higher density of fractures and water-bearing fractures were above a depth of 215 feet than below that depth. This is an important consideration when drilling wells for residential, commercial, industrial, or agricultural water supply. Abandoned underground coal mines are commonly believed to form large pools of water in the interconnected mine entries in abandoned room and pillar coal mines. Such pools of water can and do exist in abandoned underground coal mines, but many mines lack open entries and are held up by overburden strata and pillars that can collapse and form aquifers comprised of vast interconnected rubble zones (gob), especially in older mines. Data assessed for this study showed that shale-corrected values of effective porosity for limestone aquifers in West Virginia had a median value of 2 percent and an average value of 4 percent and generally are mineralized with low effective porosity. Argillaceous or sandy limestone has a median shale-corrected porosity of 4 percent and an average shale-corrected porosity of 5 percent. The median and average shale-corrected porosity of sandstone aquifers was estimated to be 14 percent, but the median shale-corrected porosity for argillaceous or calcareous sandstone was 5 percent and the average shale-corrected porosity for argillaceous or calcareous sandstone was 6 percent. Even though shale has a relatively high total sonic porosity compared to other lithologies, shale and siltstone had relatively low shale-corrected porosity, ranging from 0 to 2 percent. Well yields were previously documented to be highest in valley settings, lowest on hilltops, and intermediate on hillsides. Transmissivity data provided by this study confirm this general pattern within the Appalachian Plateaus Province; however, the Valley and Ridge Province does not follow this pattern. While still lowest on hilltop settings, the highest well yields were in hillside settings. The trend for the Valley and Ridge Province was likely skewed because of 9 high-yield wells specifically targeting deeper thin limestone units, such as the Tonoloway and Helderberg Limestones, at depths with transmissivity in excess of 2,000 feet squared per day in Mineral County, West Virginia, or targeting karst aquifers in Berkeley, Jefferson, or Greenbrier Counties, West Virginia. Finally, water-bearing fractures have been hypothesized to comprise a small number of all fractures within a typical bedrock well in West Virginia. Data collected for this study support this theory. A total of 3,403 fractures were identified during this study; 3,151 (92.6 percent) of those fractures are low-transmissive, and only 252 (7.4 percent) fractures are water-bearing. Even though a well may contain many fractures, less than 8 percent are considered water-bearing fractures.

West Virginia↗

USGS2012

Development of vegetation based soil quality indices for mineralized terrane in arid and semi-arid regions

Soil quality indices (SQIs) are often management driven and attempt to describe key relationships between above- and below-ground parameters. In terrestrial systems, indices that were initially developed and modified for agroecosystems have been applied to non-agricultural systems in increasing number. We develop an SQI in arid and semi-arid ecosystems of the Western US impacted by different types of geologic mineralization using the relationship between vegetation community parameters and soil abiotic and biotic properties. We analyze these relations in soils associated with three different mineralization types: podiform chromite, Cu/Mo porphyry, and acid-sulfate gold vein systems at four different sites in California and Nevada. Soil samples were collected from undisturbed soils in both mineralized and nearby unmineralized substrates as well as from waste rock and tailings. Aboveground net primary productivity (ANPP), canopy cover and shrub density were measured for the vegetative communities. Minimum data sets were developed based on correlations between the soil and vegetation parameters, refined using principal components analysis, scored using non-linear functions, and combined into an overall SQI. The indices are comprised of one or two microbial parameters and three to six abiotic parameters, the latter consisting of nutrients and metals. Given the preliminary development of this approach, the parameters and combinations to arrive at an SQI for a given site cannot at this time be correlated or compared with that of another site. This SQI approach provides a means of quantifying disturbed ecosystem recovery resulting from mining, and could be applied to other disturbances in a way that readily distills the information for potential use by land managers. However, severely disturbed areas with little to no aboveground biomass, such as unreclaimed tailings, have likely crossed an ecological threshold that precludes the use of this type of monitoring tool.

California↗

USGS2024

Aboveground carbon stocks across a hydrological gradient: Ghost forests to non-tidal freshwater forested wetlands

Upper estuarine forested wetlands (UEFWs) play an important role in the sequestration of atmospheric carbon (C), which is facilitated by their position at the boundary of terrestrial and maritime environments but threatened by sea level rise. This study assessed the change in aboveground C stocks along the estuarine–riverine hydrogeomorphic gradient spanning salt-impacted freshwater tidal forested wetlands to freshwater forested wetlands in seasonally tidal and nontidal landscape positions. Standing stocks of C in forested wetlands were measured along two major coastal river systems, the Winyah Bay in South Carolina and the Savannah River in Georgia (USA), replicating and expanding a previous study to allow the assessment of change over time. Aboveground C stocks on these systems averaged 172.9 Mg C ha −1 , comparable to those found in UEFWs across the globe and distinct from the terrestrial forested ecosystems they are often considered to be a part of during large-scale C inventory efforts. Groundwater salinity conditions as low as 1.3 ppt were observed in conjunction with losses of aboveground C. When viewed in context alongside expected sea level rise and corresponding saltwater intrusion estimates, these data suggest a marked decrease in aboveground C stocks in forested wetlands situated in and around tidal estuaries.

Georgia, South Carolina↗

USGS2022

U-Pb scheelite ages of tungsten and antimony mineralization in the Stibnite-Yellow Pine district, central Idaho

The Stibnite-Yellow Pine district contains the largest antimony resource in the United States, as well as significant gold, and is a historic producer of tungsten. Application of in situ laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) direct dating of scheelite from two Au-Sb-W ore deposits, Yellow Pine and Hangar Flats, yielded an older group of U-Pb ages in the range of 60.0 ± 2.8 to 57.0 ± 1.1 Ma and a younger U-Pb age for scheelite intergrown with stibnite of 47.4 ± 1.1 Ma. These in situ analyses were calibrated by isotope dilution-thermal ionization mass spectrometry (ID-TIMS) U-Pb lower intercept ages of two coarsely crystalline scheelite samples that yielded ages of 57.52 ± 0.22 and 56.62 ± 0.16 Ma. Scheelite of the latter age is of sufficient quality to serve as a primary reference material for LA-ICP-MS scheelite U-Pb geochronology. The group of older U-Pb scheelite ages agrees with 40 Ar/ 39 Ar ages of 56.9 ± 1.2 to 56.38 ± 0.54 Ma on adularia from Yellow Pine and Hangar Flats, whereas the younger U-Pb scheelite age is similar to an 40 Ar/ 39 Ar age of 46.00 ± 0.40 Ma on adularia from an epithermal gold-silver deposit in the adjacent Thunder Mountain caldera. Our results indicate that the main stage of tungsten mineralization occurred at ca. 57 Ma, whereas the main stage of antimony mineralization occurred at ca. 47 Ma—thereby providing first-time age constraints for antimony and tungsten mineralization in the Stibnite-Yellow Pine district.

Idaho↗

USGS2025

Landsliding follows signatures of wildfire history and vegetative regrowth in a steep coastal shrubland

Five years after the deadly and destructive 9 January 2018 Montecito debris flows (Santa Barbara County, California, USA), an atmospheric river storm on 9 January 2023 triggered widespread landsliding that affected many of the same drainages in the Santa Ynez Mountains. Using high-resolution aerial imagery, we identified >10,000 landslides over an ∼160 km 2 area. Most of the landslides were shallow (<1 m in depth) translational debris slides that initiated on steep (∼40°), south-facing hillslopes, with the highest incidence of landsliding in a sandstone-dominated bedrock unit. The landslides mobilized into debris flows and delivered substantial quantities of sediment downstream, which contributed to costly infrastructure impairments. We detected order-of-magnitude differences in landslide density across the study area that could not be attributed to variations in geomorphology (topographic aspect and slope), geology (bedrock type), or hydrology (seasonal antecedent rainfall, peak hourly storm rainfall intensity, total storm rainfall), which are usually considered relevant factors for shallow landsliding. Rather, we found that vegetation regrowth following wildfire was likely a relevant factor associated with the highly variable landslide densities. Hillslopes with less and different types of vegetation regrowth after fire appear to have been more susceptible to shallow landslides. We identify a possible vegetation control on postfire landsliding, which highlights an opportunity for hypothesis testing using more advanced techniques to track the evolution of vegetation cover and vegetation type in steep shrubland environments following wildfire.

California↗

USGS2026

Assessment of extreme subsurface hydrologic conditions captured during atmospheric river storms in the San Francisco Bay area (California, USA) with applications to shallow landslide early warning

An increase in soil pore water pressure is the typical trigger for the majority of landslides caused by rainfall. Atmospheric river storms, common to the west coast of North America during the winter season, can deliver landslide triggering rainfall resulting in severe impacts to coastal communities. Using a network of hydrologic monitoring stations situated within landslide-prone terrain in the San Francisco Bay area of California (USA), we assess the meteorologic conditions and resulting hydrologic and landslide response resulting from eight consecutive storm events that caused thousands of shallow landslides during the winter of 2022–2023. We find disparate hydrological responses and resultant degrees of observed landsliding ranging from < 1 landslide/km2 to 18 landslides/km2 at the monitoring sites that reflect the interplay and differences between rainfall delivery, subsurface hydrological characteristics, and geotechnical properties at each site. Antecedent soil moisture from both early season rainfall and the first storm in the sequence played a critical role in setting up some hillslopes for failure. Subsequent storms then generated elevated pore water pressures for several hours with associated landsliding. However, we find that the occurrence of widespread landsliding required not only sufficient pore water pressure magnitude in susceptible hillslopes, but also full and prolonged effective soil saturation throughout hillslope profiles. Landslides may still occur at lower values and durations of effective saturation but are likely to be less extensive regionally. We present these findings within the context of research directions and improvements to landslide early warning systems first suggested by researchers 40 years ago.

California↗

USGS2025

Strong shaking from past Cascadia Subduction Zone earthquakes encoded in coastal landforms

Strong earthquakes along subduction zones are often devastating events, but sparse records along some tectonic margins limit our understanding of seismic hazards. Constraining shaking intensities is critical, especially in subduction zones with infrequent but large-magnitude earthquakes like the Cascadia Subduction Zone (CSZ), where the lack of recorded ground motions has led to uncertainty in the severity and potential impacts of future earthquakes. Here we fill this observational gap with a novel inventory of quantitative estimates of past shaking intensities from geotechnical modeling of coastal landforms. One hundred fifty-four deep-seated landslides and 65 fragile geologic features constrain minimum and maximum peak ground accelerations, respectively. These estimates are broadly consistent with model predictions of M9 ruptures, suggesting strong shaking of 0.4–0.8 g during past CSZ earthquakes. Local discrepancies between our geologic shaking constraints and earthquake simulations may inform past rupture behavior, leading to better predictions of shaking intensity for future earthquakes.

California, Oregon, Washington↗

USGS1999

Comparison of two approaches for determining ground-water discharge and pumpage in the lower Arkansas River Basin, Colorado, 1997-98

In March 1994, the Colorado Division of Water Resources (CDWR) adopted “Rules Governing the Measurement of Tributary Ground Water Diversions Located in the Arkansas River Basin” (Office of the State Engineer, 1994); these initial rules were amended in February 1996 (Office of the State Engineer, 1996). The amended rules require users of wells that divert tributary ground water to annually report the water pumped monthly by each well. The rules allow a well owner to report the pumpage measured by a totalizing flowmeter (TFM) or pumpage determined from electrical power data and a power conversion coefficient (PCC) (Hurr and Litke, 1989). Opinions by representatives of the State of Kansas, presented before the Special Master hearing a court case [State of Kansas v. State of Colorado, No. 105 Original (1996)] concerning post-Compact well pumping, stated that the PCC approach does not provide the same level of accuracy and reliability as a TFM when used to determine pumpage. In 1997, the U.S. Geological Survey (USGS), in cooperation with the CDWR, began a 2-year study to compare ground-water pumpage estimates made using the TFM and the PCC approaches. The study area was along the Arkansas River between Pueblo, Colorado, and the Colorado-Kansas State line (fig. 1). The two approaches for estimating ground-water discharge and pumpage were compared for more than 100 wells completed in the alluvial aquifer of the Arkansas River Basin. The TFM approach uses an inline flowmeter to directly measure instantaneous discharge and the total volume of water pumped at a well. The PCC approach uses electrical power consumption records and a power conversion coefficient to estimate the pumpage at ground-water wells. This executive summary describes the results of the comparison of the two approaches. Specifically, (1) the differences in instantaneous discharge measured with three portable flowmeters and measured with an inline TFM are evaluated, and the statistical differences in paired instantaneous discharge between the two approaches are determined; (2) short- and long-term variations in the PCC’s are presented; (3) differences in pumpage between the two approaches are evaluated, and the statistical differences in pumpage between the two approaches are determined; (4) potential sources of discrepancy between pumpage estimates are discussed; and (5) differences in total network pumpage using the two approaches are presented. During the irrigation seasons of 1997 and 1998, instantaneous discharge and electrical power demand were measured at randomly selected wells to determine PCC’s. At more than 100 wells, the PCC’s determined during the 1998 season were applied to total electrical power consumption data that was recorded between the initial and final readings at each network well site in 1998 to estimate total ground-water pumpage. At each site, an inline TFM was installed in a full-flowing, acceptable test section of pipe on the discharge side of the pump where the measurement of discharge was made. Measurements of instantaneous ground-water discharge also were made using three different types of portable flowmeters. The average velocity multiplied by the cross-sectional area of the discharge pipe was used to compute the discharge in gallons per minute. Whenever possible, discharge measurements were made at each network site using all three types of portable flowmeters.

Colorado↗

USGS2025

Natural source zone depletion of crude oil in the subsurface: Processes controlling mass losses of individual compounds

At many petroleum hydrocarbon spill sites, residual spilled product forms a long-term source of groundwater contamination. The phrase source zone natural depletion is used to refer to the mass loss rates. Overall mass lost under environmental conditions was analyzed using conservative biomarker concentrations for a 1979 oil spill in northern Minnesota, USA. After 40–41 years, an average of 50% of the mass was lost with values ranging from 22% to 57% depending on location. It is also important to understand the composition changes in the source. To understand controls on the losses of individual compounds, concentrations of volatile hydrocarbons in oil samples were compared with aqueous solubilities, and pore-space oil saturations. The results of the comparison show that losses of the oil compounds were controlled by pore-space oil saturations, solubility, and susceptibility to degradation under methanogenic conditions. Compounds that degrade under methanogenic conditions, including toluene, o -xylene, and n -alkanes are more depleted compared to benzene, ethylbenzene, and m - and p -xylene for which losses are dominated by dissolution. These rates and compound-specific behaviors form a foundation for improved modeling approaches and risk analyses.

Minnesota↗

USGS2025

Mapping potential sensitivity to hydrogeomorphic change in the UMRS riverscape

In 2020 the U.S. Geological Survey (USGS), as part of the Upper Mississippi River Restoration (UMRR) Program, began a new project to characterize potential hydrogeomorphic change associated with hydrogeomorphic units (HGUs) and their catenae (units linked by their association with sediment sources and flow origins). The goal of the project was to develop a geographic information system (GIS) database of HGUs for the Upper Mississippi River System (UMRS) available to both scientists and river managers working on UMRR studies and HREP planning and design studies. The characterization was based on a hydrogeomorphic change hierarchical classification developed previously for the UMRS. The products were generated with automated techniques in a GIS using systemic datasets. Landforms were mapped from the 2015 UMRS topobathymetric dataset with geomorphon (shape-based) tools tailored for the large riverscape, valley bottom environments in the UMRS. A clustering analysis was applied to the resulting landforms to identify HGUs associated with zones of perennial low flows, bankfull flows, and overbank floodplains. Catenae were assembled based on the proximity of the units to the main channel, tributary mouths, and side channels from previously published aquatic areas (USACE, 2018) coupled with least-cost flowpath linkages between potential sediment origins and planform change units developed by Rogala, Fitzpatrick, and Henderson (2020). These GIS-based analyses were successful at identifying a range of HGUs using an automated technique with available data across the entire riverscape, with emphasis on those that have the potential for hydrogeomorphic change. Most of the resulting features are depositional, as expected in a large river system. However, this is the first attempt of linking tributary inputs, side channel erosion and levee breaches with their depositional counterparts. The approach was successfully piloted in Pools 8 and 10 in the Upper Impounded Reach and Pool 14 in the Lower Impounded Reach, with next steps for application in reaches of the unimpounded section and Illinois River. This report emphasizes results from Pool 10, which was the focus of most of our attention during the pilot phase.

Illinois, Indiana, Iowa, Minnesota, Missouri, Sout↗

USGS2024

Precariously balanced rocks in northern New York and Vermont, U.S.A.: Ground-motion constraints and implications for fault sources

Precariously balanced rocks (PBRs) and other fragile geologic features have the potential to constrain the maximum intensity of earthquake ground shaking over millennia. Such constraints may be particularly useful in the eastern United States (U.S.), where few earthquake‐source faults are reliably identified, and moderate earthquakes can be felt at great distances due to low seismic attenuation. We describe five PBRs in northern New York and Vermont—a region of elevated seismic hazard associated with historical seismicity. These boulders appear to be among the most fragile PBRs in the region, based on reports from hobbyists. The PBRs are glacial erratics, best evidenced by glacial striations on bedrock pedestals. The pedestals themselves are locally high knobs, often situated on regionally high topography; this setting limits soil development and indicates that any outwash deposits were likely ephemeral. As a result, PBR ages can be reliably established by the retreat of the last continental ice sheet, ∼15–13 ka. To quantify the fragility of the PBRs, we surveyed them with ground‐based light detection and ranging and calculated geometric parameters from the point clouds, field observations, and seismic responses. Preliminary validation of the 2023 time‐independent U.S. National Seismic Hazard Model (NSHM) shows that the existence of PBRs is generally consistent with the median site‐specific hazard curves. Only the Blue Ridge Road site suggests a modest reduction in hazard. To visualize the ensemble of data, we mapped the minimum permissible distance to potential source faults around each PBR site as a function of source magnitude by using the ground‐motion models from the 2023 NSHM. Viewed in this manner, our data are consistent with potential M ∼6.5 earthquake‐source faults in many parts of the Lake Champlain Valley and northern Adirondack Mountains. Our work illustrates a potential pathway for better constraining earthquake‐source faults in regions of cryptic faults.

Bulletin of the Seismological Society of America↗

USGS2026

Re-examining the growing degree day minimum for grass carp spawning initiation in Lake Erie: Have we missed the mark?

Understanding the timing of life history processes of invasive fish species, such as adult aggregations during spawning, allows natural resource managers to optimize targeted population control efforts. Temperature-based estimates of the timing of spawning initiation for grass carp ( Ctenopharyngodon idella ) exist from its native range, but have not previously been developed for grass carp reproduction in its invaded range in the Laurentian Great Lakes of North America. We accounted for differences among methods across studies and calculated cumulative growing degree days (GDD) for the dates of grass carp egg capture in Lake Erie tributaries (Sandusky, Maumee, and Huron rivers) during 2015–2024 and compared these values to the existing GDD base 15°C requirement estimate from the native range (633 GDD–15°C). The earliest egg detection in Lake Erie (Sandusky River) was 19 GDD–15°C or 361 GDD–5°C (latest egg detection was 2285 GDD–5°C from the Sandusky River), indicating that spawning was initiated up to 25 days earlier than would be predicted by the native range GDD. Moreover, spawning in Lake Erie tributaries occurred earlier than predicted for 58% of spawning events examined based on the native range GDD. The GDD values for spawning initiation in Lake Erie tributaries can be used to refine the timing of control efforts targeting pre-spawn and spawning adult fish, inform the timing of egg sampling, and provide linkages to existing early life stage models to infer the length of the growing season available for age-0 fish to reassess tributary suitability.

Lake Erie, Maumee, River, Sandusky river↗

USGS2026

Polystyrene microplastics alter the accumulation and elimination dynamics of silver nanoparticles in Daphnia magna

Rationale Microplastics (MPs) can interact with engineered nanomaterials and alter their environmental fate and bioavailability. However, their influence on the bioaccumulation dynamics of silver nanoparticles (AgNPs) in aquatic filter feeders under environmentally relevant conditions remains poorly understood. We hypothesized that polystyrene microplastics (PS-MPs) alter the uptake, elimination and overall bioaccumulation dynamics of AgNPs in Daphnia magna . Methodology Adult D. magna were exposed to isotopically labeled citrate-coated 109 AgNPs in the presence and absence of PS-MPs. Waterborne uptake, dietary uptake, assimilation efficiency, food ingestion and elimination were quantified experimentally and incorporated into a biodynamic model to predict steady-state silver (Ag) concentrations under environmentally relevant exposure scenarios. Results PS-MPs increased waterborne Ag accumulation by approximately eightfold compared with AgNPs exposure alone. However, Ag elimination was substantially faster, with 98% of accumulated Ag eliminated after five days of depuration compared with 66% without PS-MPs. PS-MPs also reduced food ingestion rates (IRs), while assimilation efficiency remained largely unchanged. Biodynamic modeling predicted that steady-state Ag accumulation was approximately fivefold greater in the presence of PS-MPs, with waterborne exposure becoming the dominant accumulation pathway. Discussion These findings suggest that PS-MPs alter bioaccumulation dynamics of AgNPs in filter-feeding organisms by enhancing organism-associated Ag during waterborne exposure while accelerating Ag elimination, likely through particle-associated transport and gut egestion. Collectively, these results underscore the complexity of Ag bioaccumulation processes when MPs and AgNPs interact and highlight the importance of studies conducted under environmentally relevant conditions.

Environmental Chemistry↗

USGS2026

Relating glassy rind thicknesses to ambient air temperatures at the Lost Jim flow field in the Imuruk Lake volcanic field, Alaska

The Lost Jim flow field, in the Imuruk Lake volcanic field, Alaska, extends west ~34 km from a single vent, crossing subarctic tundra and currently touches several lakes and streams. The weighted mean of five 36Cl cosmogenic exposure ages from the Lost Jim pāhoehoe flow is 7.73 ± 0.37 ka, indicating this eruption occurred substantially after the eruption of the underlying Camille flow, which was emplaced at 39.7 ± 1.3 ka. Paleoclimate records indicate the period when the Lost Jim flow field was emplaced was after deglaciation, and the climate was similar to today. We propose that the emplacement of lava in these cold subarctic conditions can lead to faster cooling of the lava surface compared to lava emplaced in warmer locations such as mid- latitude cold deserts. Glass abundance in the outermost rinds at the Lost Jim flow field was on average 74 % with 6.4 mm thick rims, compared to 60 % with 2.9 mm rims for cold mid-latitude desert samples. We interpret increased glass content as a proxy for rapid cooling likely occurring partly during winter. Glassiness values varied less across vent, margin, and mid-flow locations when compared to the mid-latitude flows suggesting the Lost Jim flow field was broadly impacted by the subarctic climate as opposed to responding to local microclimates. Our results indicate that lava glassiness may be a useful environmental indicator of cooler (in this case subarctic) conditions.

Alaska↗

USGS2025

Divide and conquer: Separating the two probabilities in seismic phase picking

There are two fundamental probabilities in the seismic phase picking process – the probability of the existence of a seismic phase (detection probability) and the probability of correctly identifying the phase arrival time (timing probability). The nearly ubiquitous approach in developing deep learning phase picking models is to use a kernel, such as a truncated Gaussian, to mask the labeled phase arrival time, and train a segmentation model. Once a model is trained, the times of the peaks in the output are taken as phase arrival times (picks) and the height of the peaks are taken as “probability” of the picks. Here, we show that this “probability” represents neither the detection nor the timing probabilty because this approach forces the output to follow the shape of the kernel. We introduce an approach using two models to estimate these two distinct probabilities. We use a binary classifier with a calibrated confidence to address the detection probability and a multi-class classifier to obtain a probability mass function to address the timing probability. This new approach makes the deep learning-based phase picking process more interpretable and gives us options to logically control seismic monitoring workflows.

Geophysical Journal International↗

USGS2000

Method for estimating water use and interbasin transfers of freshwater and wastewater in an urbanized basin

Techniques for management of drainage basins that use water budgets to balance available water resources with actual or anticipated water use require accurate and precise estimates of basin withdrawals, interbasin transfers of freshwater, unaccounted-for use, water use, consumptive use, inflow and infiltration, basin return flow, and interbasin transfers of wastewater. Frequently, interbasin transfers of freshwater and wastewater are not included in basin water budgets because they occur within public water-delivery and wastewater-collection systems. A new 10-step method was developed to improve estimates of inflow and infiltration and interbasin transfers using readily available statewide data. The accuracy and precision of water-use estimates determined by this method are improved through careful application of coefficients for small users and the use of metered values for large users. The method was developed and tested with data for the Ten Mile River Basin in southeastern Massachusetts. This report uses examples from the basin to illustrate each step of the method.

Massachusetts↗

USGS2026

Reassessing water availability in the Nile River Basin using satellite-based irrigation water use accounting

Existing estimates of irrigation areas and water use in the Nile River Basin vary widely and are based on inconsistent data and methodologies. This study leverages advances in remote sensing to provide an up-to-date and consistent basin-wide reassessment of water use in the Nile River Basin. Land cover and actual evapotranspiration data from 2013 to 2022 were used to quantify irrigated areas, irrigation water use, and the average naturalized water yield. Across the basin, 7.1 million hectares of irrigated land consume an average of 72.5 ± 2.6 billion cubic meters (BCM) of blue water annually. Egypt and Sudan together account for 92% of the irrigated area and 97% of the irrigation water use. The basin’s average naturalized yield, evaluated at Dongola station, is determined to be between 108 and 114.4 ± 3.2 BCM. Although conservative, this updated analysis indicates the basin’s average naturalized yield is 14%–20% higher than the previous naturalized yield estimate (95 BCM) and 29%–36% higher than the commonly cited observed flow of 84 BCM, which is frequently treated as the total basin-wide available water. Importantly, the study underscores that the 84 BCM represents flow at the Aswan gauging station after upstream consumptive uses, not the total water available in the basin under naturalized conditions. This distinction is critical for accurate water accounting, planning, and governance in this water-scarce basin. This study demonstrates the value of open-source remote sensing resources in data-scarce regions while emphasizing the need for region specific validation and bias correction for improved accuracy.

Nile River Basin↗

USGS2026

Cotton farming pesticides affect ileal microbiota activity expressions of virulome but not resistome or metabolic pathways in a sedentary wild passerine

The increased use of agrochemicals to enhance crop production has had detrimental environmental effects including implication in the sharp decline of North American farmland-breeding birds. Here, using a combination of deep shotgun metatranscriptomics and pesticide exposure data, we sought to assess whether exposure to cotton ( Gossypium spp.) production had a differential effect on ileum multi-kingdom microbial activity, metabolism, anti-microbial resistance, and virulence factors of sedentary northern mockingbirds ( Mimus polyglottos ) sampled from two cotton-producing areas (16 birds in total) and one uncultivated area (7 birds) in Texas, USA. Both Shannon Index values (Adj. r 2 = 0.174, F (1,21) = 5.633, p = 0.027) and a Mantel test (Spearman ρ = 0.184, p = 0.013) supported a relationship between metabolically active microbiota Bray–Curtis dissimilarities and differences in pesticide mixtures among study areas. Virulence factor richness (Adj. r 2 = 0.182, F (1,21) = 5.890, p = 0.024), Shannon Index (Adj. r 2 = 0.231, F (1,21) = 7.612, p = 0.012), and load (sum of virulence factor abundances; Adj. r 2 = 0.160, F (1,21) = 5.194, p = 0.033) were related to total pesticide load (total quantity of pesticides). We found no pesticide effects on expression of either antimicrobial resistance genes or metabolic pathways.

Texas↗