USGS Science⌕ Search

SEARCH · USGS Science

Results for “Geological Society, London, Special Publications”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

770 records · Page 29Linked to original sources
USGS2025

System characterization report on the Environmental Mapping and Analysis Program (EnMAP)

This report addresses system characterization of the Environmental Mapping and Analysis Program hyperspectral sensor by the DLR (German Aerospace Center, ground segment project management), GFZ (Deutsches Geoforschungszentrum, science lead) and is part of a series of system characterization reports produced and delivered by the U.S. Geological Survey Earth Resources Observation and Science Cal/Val Center of Excellence. These reports present and detail the methodology and procedures for characterization; present technical and operational information about the EnMAP hyperspectral sensor; and provide a summary of test measurements, data retention practices, data analysis results, and conclusions. The Earth Resources Observation and Science Cal/Val Center of Excellence system characterization team completed data analyses to characterize the geometric (interior and exterior), and radiometric performances of the EnMAP hyperspectral sensor. Results of these analyses indicate that the Environmental Mapping and Analysis Program has a band-to-band geometric performance in the range of −0.135 to 0.15 pixel, geometric performance relative to the Operational Land Imager in the range of −27.716 meters (−0.92 pixel) to 32.892 meters (1.09 pixels) offset in comparison to Landsat 8 Operational Land Imager, offset of a radiometric comparison in the range of −0.012 to 0.020, slope of a radiometric comparison in the range of 0.947 to 1.031.

Open-File Report↗
USGS2026

Colored shaded-relief bathymetric and acoustic-backscatter maps of Jenkinson Lake with orthomosaic of the Sly Park Creek and Hazel Creek area, California

The Caldor Fire was ignited on August 14, 2021, and burned almost 222,000 acres (898 square kilometers) in forested terrain of the central and western Sierra Nevada, California. During the subsequent two months, the fire burned nearly all of Sly Park Creek watershed in El Dorado County. The El Dorado Irrigation District manages the water supply for the area using storage in Jenkinson Lake, a 1.6-kilometer- (1.0-mile-) wide and 3.6-kilometer- (2.2-mile-) long reservoir, located south of the town of Pollock Pines. Several weeks after the fire, the U.S. Geological Survey began investigations into post-fire landscape responses, including sediment yield, by measuring new sediment deposition in Jenkinson Lake. This study focused on the collection and processing of bathymetric and acoustic-backscatter data, as well as onshore aerial imagery in and around Jenkinson Lake, to support wildfire science after the Caldor Fire. A colored shaded-relief bathymetric map (sheet 1) and an acoustic backscatter map (sheet 2) show the lake floor morphology and backscatter intensities.

California↗
USGS1996

Techniques to estimate generalized skew coefficients of annual peak streamflow for natural basins in Texas

This report presents two techniques to estimate generalized skew coefficients used for log-Pearson Type III peak-streamflow frequency analysis of natural basins in Texas. A natural basin has less than 10 percent impervious cover, and less than 10 percent of its drainage area is controlled by reservoirs. The estimation of generalized skew coefficients is based on annual peak and historical peak streamflow for all U.S. Geological Survey streamflow-gaging stations having at least 20 years of annual peak-streamflow record from natural basins in Texas. Station skew coefficients calculated for each of 255 Texas stations were used to estimate generalized skew coefficients for Texas. One technique to estimate generalized skew coefficients involved the use of regression equations developed for each of eight regions in Texas, and the other involved development of a statewide map of generalized skew coefficients. The weighted mean of the weighted mean standard errors of the regression equations for the eight regions is 0.36 log 10 skew units, and the weighted mean standard error of the map is 0.35 log 10 skew units. The technique based on the map is preferred for estimating generalized skew coefficients because of its smooth transition from one region of the State to another.

Texas↗
USGS2024

Neotectonic mapping of Puerto Rico

Puerto Rico is part of the Puerto Rico-Virgin Islands microplate, along the Caribbean–North American plate boundary between the Puerto Rico trench subduction zone and the Muertos Trough incipient subduction zone. Despite recent seismicity and geodetically constrained deformation of ~3 mm/yr of left-lateral shear across the island, Quaternary fault locations remain largely uncertain. Preservation of recent faulting in the landscape is masked by distributed faulting, high weathering rates of the tropical climate, steep topography, frequent landsliding, and extensive agriculture and urbanization along coastlines and river valleys. We present remote neotectonic mapping of historical aerial imagery from the 1930s-60s and <1-m lidar topography, integrated with field observations, to create an updated active fault map of Puerto Rico. We focus on faults that offset younger geomorphic surfaces, with ages estimated by geologic mapping, OSL and radiocarbon dating, and morphologic interpretations. We present new evidence for Quaternary activity on seven faults, including the South Lajas, Salinas, Punta Montalva, Great Southern Puerto Rico, Cerro Goden, Parguera, and San Marcos faults. We find that active faulting occurs preferentially along the southern and western coasts and does not always spatially coincide with preexisting bedrock faults, possibly reflecting partial reactivation of older faults in the modern strain field.

Puerto Rico↗
USGS2025

Enhancing mineral systems exploration through geochronology, thermochronology, and isotope analysis: USGS Geochron and USGS Isotope databases

A mineral systems approach to mineral exploration provides a comprehensive framework for understanding ore deposit formation by examining the geodynamic, magmatic, hydrothermal, and sedimentary processes responsible for mineralization, alteration, and remobilization of economic mineral deposits. Temporal and thermal constraints on ore genesis are crucial for refining mineral system models and guiding predictive exploration strategies. Geochronology and thermochronology offer invaluable insights into the timing and thermal evolution of ore-forming processes, whereas isotopic analyses provide critical information on the source and geochemical history of ore-forming fluids. Combining these methodologies have proven highly effective for mineral exploration in regions like Australia, however, their combined application has been limited in the United States. To apply these tools to mineral systems-based exploration, the U.S. Geological Survey (USGS) has developed two products: (1) The USGS Geochron Database, and (2) the USGS Isotope Database. These databases provide centralized repositories of geo/thermochronological dates and data (Geochron Database) and both radiogenic and stable isotope data (Isotope Database) generated by the USGS and partners over the past decades. Integrating these datasets together and with traditional exploration approaches provides the mineral exploration community with powerful tools for determining the temporal and thermal histories of ore systems and identifying metallogenic source provinces.

Continental United States↗
USGS2024

The 3D Elevation Program—Supporting New Hampshire’s economy

Introduction The topography of New Hampshire ranges from the Coastal Lowlands to the Eastern New England Upland to the White Mountains region. High-quality statewide elevation data are useful in managing this very diverse landscape. For example, the short coastline, including the Great Bay estuary and the Hampton-Seabrook marshes, is of disproportionately high value to New Hampshire’s tourist economy. The vulnerability of the coast to the effects of sea-level rise underscores the need for accurate, high-quality nearshore topographic elevation data and offshore bathymetric data to effectively manage the coast’s valuable resources, which include important fisheries, habitat, and infrastructure. Another important use for accurate elevation data in New Hampshire is in the evaluation of flood hazards and their potential environmental and infrastructure effects. This evaluation includes mapping of inundation and sediment transport, and assessing the associated costs of flooding. Addressing this challenge requires detailed knowledge of both surface topography and inland bathymetry. Other important activities having a substantial economic element and needing accurate elevation data include geologic resource assessment and hazard mitigation, urban and regional planning, infrastructure and construction management, and cultural resources preservation and management. Critical applications that meet the State’s management needs depend on light detection and ranging (lidar) data that provide a highly detailed three-dimensional model of the Earth’s surface and aboveground features.

New Hampshire↗
USGS2026

Production of mineral commodities and geospatial map of the mineral industries and related infrastructure of China

As part of the U.S. Geological Survey’s (USGS) mission to distribute global mineral information and analyze supply chains, this study provides a comprehensive review of the global significance of China’s mineral production and capacity in 2023. Of 77 mineral commodities in the USGS dataset, China produced 74 and was the world’s first-ranked producer for 39 of the 74. Compared to the high share of global mineral production, including up to 98 percent of global gallium production, the country’s share of global mineral reserves was relatively small, ranging from 20 percent (zinc ore) to 52 percent (tungsten ore). China’s imports of metal ores, slag, and ash accounted for 64 percent of global imports of such commodities by value. The country’s exports of base metals and articles of base metal accounted for 17 percent of the global exports. To help nongeographic information system users assess the spatial distribution of mineral mines, processing facilities, and ports for trades in China, this study created a geospatial (also called “georeferenced”) portable document format (GeoPDF) map. In addition, the GeoPDF contains mineral resource tracts (such as antimony, copper, potash, coal, and oil and gas), exploration sites, and energy infrastructure based on the preexisting USGS data.

Open-File Report↗
USGS2024

Development of USGS NSHMs: Do small changes in hazard imply small changes in risk?

One of the flagship products from the U.S. Geological Survey (USGS) is the National Seismic Hazard Model (NSHM). Since 1976, the NSHM has been periodically updated to reflect newly published earthquake science and provide probabilistic estimates of seismic hazard for the United States. During each update cycle, alternative models are deliberated, analyzed, and documented through logic trees and their corresponding logic tree branch weights. For example, the decision to modify a logic tree branch weight may be influenced by sensitivity analyses of the logic tree branches in their effects on the mean hazard. However, do small changes in traditional measures of hazard imply small changes in risk? In this study, we make use of two update cycles of the USGS NSHMs and a National Bridge Inventory (NBI) from the Federal Highway Administration (FHWA) to explore the preceding question. Specifically, we first identify geographic locations in the conterminous United States in which the change in hazard from one cycle to another is relatively small. Next, we model the seismic risk to highway bridges for these locations and for each update cycle, while simultaneously distinguishing low hazard environments from high hazard environments. These data enable quantitative analysis of how much changes in risk can be expected given small changes in hazard, investigating the importance of risk models in decision-making during development of the USGS NSHMs.

Conference Paper↗
USGS2025

Probing lower-crustal fault properties with frequency-dependent tidal tremor triggering

The way seismicity responds to periodic stress perturbations offers crucial insights into the processes that can trigger an earthquake. Laboratory and theoretical analyses have shown that the period of imposed forcing and source properties affect the sensitivity to triggering, but frequency-dependent triggering of tectonic faults is poorly understood. The rate of low-frequency earthquakes (LFEs) near Parkfield, California has been found to be strongly correlated with solid earth tides. Tidal forcing acts over multiple frequencies, and the sensitivity to tidal triggering of LFEs therefore provides a unique opportunity to probe the physics of earthquake triggering and underlying fault properties. Here, we find that the response of LFEs to solid earth tides at diurnal and semi-diurnal frequencies is highly variable but spatially coherent along the San Andreas Fault. Using rate-state friction modeling, we find that the variation of the amplitude of tidal modulation is mainly affected by the spatial variation of the background effective normal stress, whereas the spatially varied tidal modulation at diurnal and semi-diurnal frequencies is mainly affected by the fault frictional property. The spatial variations of the LFE response reveal a heterogeneous lower-crustal geologic structure and complex physical faulting processes below the rupture zone of eventual great earthquakes.

California↗
USGS2026

Hydrogeologic conceptualization of the Arroyos subarea and Northeast Air Force Research Laboratory subarea of the Air Force Research Laboratory, Edwards Air Force Base, Antelope Valley, California, 2017–21

Research and testing within the Air Force Research Laboratory at Edwards Air Force Base in the southwestern Mojave Desert has been conducted since the 1950s. This testing requires large quantities of groundwater for cooling and operations involving hazardous constituents that have entered the groundwater. To better understand the potential movement of contaminants through the groundwater system, the U.S. Geological Survey entered into a cooperative agreement with the U.S. Air Force Civil Engineer Center with the purpose of (1) gaining a more detailed understanding of the hydraulic connection between the unconsolidated basin-fill sediment and the underlying weathered and crystalline bedrock and (2) investigating faults and their potential effect on groundwater flow. This study was specific to the Arroyos subarea and Northeast Air Force Research Laboratory subarea of the Air Force Research Laboratory. The refined hydrogeologic characterization was derived by evaluating surface geologic maps, a regional gravity model, new subsurface geophysical surveys, lithology data from boreholes, and groundwater-level data. Refinement of the hydrogeologic characterization of the study area involved developing a map of basin-fill sediment thickness, estimating the geometry and depth to bedrock, determining the presence of weathered bedrock material, and identifying the location of faults and subsurface structures. The thickness of basin-fill sediment was derived from a regional gravity model. Basin-fill sediment ranges from less than 20 feet (ft) thick to about 150 ft thick and increases substantially toward a deep structural basin in the northwestern part of the study area. The top of bedrock estimated from the new surface geophysical surveys is generally deeper than the top of bedrock from the regional gravity model. These differences in interpreted bedrock tops indicate that there may be a zone of weathered bedrock in the subsurface, overlying crystalline bedrock. Additional subsurface data evaluating the geometry and thickness of weathered bedrock are necessary for a comprehensive evaluation of weathered bedrock in the study area. Previously unmapped extensions of the Leuhman Fault, Spring Fault Zone, and Boron Gate Fault were identified in the new surface geophysical surveys. Evaluation of groundwater flow between bedrock and basin-fill sediment, and the effects of faults on groundwater flow, was done using groundwater-level data from 2020. The groundwater table was in crystalline bedrock throughout most of the Arroyos and Northeast Air Force Research Laboratory subareas, with a few exceptions where it was in basin-fill sediment and weathered bedrock. Basin-fill sediment, and likely weathered bedrock, was partially saturated in parts of the study area where basin-fill sediment was as thick as 150 ft. Weathered bedrock material may be present near the Spring Fault Zone, and if so, was likely saturated in 2020. The groundwater-level data near and within Spring Fault Zone indicate that the Spring Fault Zone acts as a vertical-along-strike conduit for, and as an across-strike impediment to, groundwater flow. In addition, steep groundwater-level gradients in the southeastern part of the study area indicate that a subsurface structure affecting groundwater flow could be related to the Leuhman Fault. Sufficient groundwater-level data were not available to conclusively determine if the Arroyos, Rich, and Boron Gate Faults, and their inferred extensions from the geophysical surveys, affect the movement or direction of groundwater flow.

California↗
USGS2026

Evaluation of stream capture related to groundwater pumping, middle Humboldt River Basin, Nevada

Historical, future, and potential stream capture from groundwater pumping in the middle Humboldt River Basin (MHRB), Nevada, is estimated using a calibrated numerical groundwater flow model. The model was developed to estimate (1) stream capture, which is the change in flux between the groundwater system and the Humboldt River and tributaries, and (2) change in streamflow, which is the change in streamflow estimated for the Imlay gage on the Humboldt River (U.S. Geological Survey streamgage 10333000). Historical stream capture for water years (WYs) 1961–2015 is estimated using recorded and estimated groundwater pumping during that period. Future (predictive) stream capture was based on historical stresses (WYs 1961–2015) using a scenario that simulated non-mine pumping from WY 2015 at a uniform rate for 100 years into the future. Potential stream capture throughout the middle Humboldt River Basin from groundwater pumping during varying durations of time are presented in a series of capture maps. Maps also are presented that show the potential to capture from groundwater evapotranspiration, as well as the storage changes for pumping duration of 100 years. Estimates of historical stream capture from the mainstem Humboldt River during the early 1960s are less than 400 acre-feet per year (acre-ft/yr) when groundwater withdrawals and pumping rates were relatively small compared to more recent times. In the late 1980s and early 1990s, groundwater withdrawals increased and estimated historical stream capture also increased from about 4,000 acre-ft/yr in the late 1980s and early 1990s to as much as 18,800 acre-feet (acre-ft) in WY 1998. In WY 2015, estimated historical stream capture declined to about 13,000 acre-ft because of decreasing groundwater withdrawals and lower streamflow during the drought of WYs 2012–15, resulting in less stream water available for capture. Stream capture was estimated for 100 years into the future based on WY 2015 non-mine pumping rates and mine-dewatering activity through WY 2015. Stream capture is forecast to increase to about 23,000 acre-ft/yr, and streamflow in the Humboldt River could decrease by as much as 19,000 acre-ft/yr. Pumping for mine-dewatering and the associated discharge of that water affects streamflow in the Humboldt River at Imlay, Nevada (U.S. Geological Survey streamgage 10333000). Historically, from WYs 1991 to 2015, streamflow was greater at Imlay gage during active mine-dewatering from mine-water discharge operations and increased by as much as 105,000 acre-ft in WY 1998. The increase was attributed mostly to the discharge of groundwater from mine-related dewatering operations directly into the mainstem Humboldt River or its tributaries, with some of this increase associated with return flows from discharge to rapid infiltration basins. Results indicate that streamflow at Imlay gage is expected to decrease by as much as 1,600 acre-ft/yr 30 years after mine-related pumping and discharge are discontinued. The streamflow reductions at the Imlay gage are expected to then decrease to around 500 acre-ft/yr, 100 years after mine-related pumping and discharge are discontinued. Potential capture maps were produced for pumping durations of 10, 25, 50, and 100 years. Capture map results indicate that areas of greater potential stream capture occur adjacent to the Humboldt River and for upstream tributaries areas north of the Humboldt River.

Nevada↗
USGS2024

A great tsunami earthquake component of the 1957 Aleutian Islands earthquake

The great 1957 Aleutian Islands earthquake ruptured ∼1200 km of the plate boundary along the Aleutian subduction zone and produced a destructive tsunami across Hawaiʻi. Early seismic and tsunami analyses indicated that large megathrust fault slip was concentrated in the western Aleutian Islands, but tsunami waves generated by slip in the west cannot explain the large observed runup in Hawaiʻi far to the southeast. Recently mapped 1957 geologic deposits on eastern Aleutian Islands suggest occurrence of very large nearby slip. Jointly modeling tsunami runup along the eastern Aleutian and Hawaiian Islands together with tide gauge recordings across the Pacific resolves 12-26 m shallow slip along 600 km of the eastern Aleutian Islands in addition to modest, deeper western slip inferred from seismic records. The eastern near-trench slip results in an M W 8.3-8.6 tsunami earthquake component of the M W 8.6-8.8 rupture, comparable in size to the adjacent 1946 Aleutian tsunami earthquake to the east. The reexamination of the 1957 rupture confirms the tsunami hazards posed by the eastern Aleutian subduction zone to Hawaiʻi and lays the groundwork for investigation of large prehistoric earthquakes through modeling tsunami runup inferred from stratigraphic observations to constrain their rupture processes.

Alaska↗
USGS2026

Decadal trends and occurrence of geogenic constituents and mixtures in groundwater across the continental United States

Worldwide, about 50% of the population is served by groundwater-sourced drinking water. Numerous groundwater quality assessments have found that geogenic constituents are among the most common contaminants in drinking-water aquifers. Documenting changing groundwater quality is a crucial aspect of water availability assessments. We assess trends and occurrence of geogenic constituent concentrations in groundwater across the continental United States using 3 decades of data from the U.S. Geological Survey’s National Water Quality Network. Thousands of groundwater wells were grouped into agricultural, urban, or domestic supply network types. Although most networks and constituents had no statistically significant change in concentration, many had increasing concentration trends, elevated concentrations, or both. Lithium, sodium, radium, sulfate, and uranium had increasing trends in more than 10% of the study networks. Urban and domestic well networks had increasing lithium and sodium trends more often than agricultural networks. Manganese most commonly increased in domestic well networks; uranium more commonly increased in agricultural and urban networks. Elevated concentration mixtures were widespread, and mixture complexities appeared to increase over time. Our results indicate that more than 2.3 million domestic-well users may be affected by elevated concentrations of one or more geogenic constituents.

continental United States↗
USGS2025

Three-dimensional seismic velocity model for the Cascadia Subduction Zone with shallow soils and topography, version 1.7

The U.S. Geological Survey’s seismic velocity model for the Cascadia Subduction Zone provides P- and S-wave velocity ( V P and V S , respectively) information from 40.2° to 50.0° N. latitude and −129.0° to −121.0° W. longitude, and is used to support a variety of research topics, including three-dimensional (3D) earthquake simulations and seismic hazard assessment in the Pacific Northwest. This report describes an update to the previous version (v) 1.6 of the 3D seismic velocity model for the Cascadia Subduction Zone. This new model (herein referred to as v1.7) contains more detailed near-surface structure for improved earthquake ground motion modeling. Updated features include the addition of a new shallow soil velocity model in the top few hundred meters and the option of adding user-specified topography. Although v1.6 of the Cascadia seismic velocity model has a minimum V S of 600 meters per second (m/s), the new model (v1.7) has a minimum V S of approximately 40 m/s. Overall, this update will allow for more accurate ground motion estimates from 3D simulations of scenario earthquakes in the Cascadia Subduction Zone region.

British Columbia, California, Oregon, Washington↗
USGS2025

Lunar grid systems, coordinate systems, and map projections for the Artemis missions and lunar surface navigation

Foreward This document contains design specifications of a navigational standard for the Moon, including a Lunar Transverse Mercator system, a Lunar Polar Stereographic system, a Lunar Grid Reference System, and a unique coordinate structure, Artemis Condensed Coordinates, for Artemis mission navigation and lunar surface science. The National Aeronautics and Space Administration (NASA) Artemis campaign seeks to place humans on the Moon for the first time since the Apollo missions. Early Artemis missions are heavily focused on the lunar south pole, which promises to return valuable data on the Moon’s geologic record, amongst other mission objectives. Coordinate systems in use today for the lunar south pole provides crew members on the surface neither an efficient nor intuitive means to communicate their position and orientation. A novel grid coordinate system, the Lunar Grid Reference System, is proposed to address these concerns for use in real-time extravehicular activity operations on the lunar surface. The many stakeholders involved in the Artemis missions will need a common system to communicate position and orientation while astronauts are operating on the lunar surface. To that end, Artemis crew members will need that system to be efficient and intuitive to promote efficient extravehicular activity timelines and reduce confusion. In the context of this document, these characteristics are addressed on the design of lunar coordinate systems: Efficient.—The number of characters required to communicate a location within a desired precision level in both local and global contexts, and how many steps are required for a recipient or sender to interpret a location. Intuitive.—How well the system aligns with human perceptual abilities, and whether the system yields distances that have the same relationship to actual lunar surface distance in all directions from the point where a person is located. Technological systems are currently being investigated to supplement the crew members’ ability to locate and orient themselves and other assets on the lunar surface; however, it is unlikely that those systems will be fully operational for the first few landed missions. Even with future positional aids, crew members will still need an efficient and intuitive means to communicate position and orientation. In addition, if technological systems fail, the crews will require land navigation skills and have maps available, thus providing further motivation for a crew-centric coordinate system. The contents of this U.S. Geological Survey (USGS) document detail a comprehensive framework for standardizing lunar crewed surface navigation within NASA and outlines the protocols, methods, and designs necessary for achieving consistency and interoperability across relevant space mission teams and lunar surface navigators. Key components of this document include designs of map projections, projected coordinate reference systems (Lunar Transverse Mercator and Lunar Polar Stereographic systems), and a grid system (Lunar Grid Reference System and Artemis Condensed Coordinates) for the Moon. The work proposed in this document seeks to accomplish something similar to the National Geospatial-Intelligence Agency (NGA) document SIG 0012 (NGA, 2014a), but for using grid systems for the Moon. This report incorporates initial feedback and input from NASA’s Artemis Geospatial Data Team, NASA’s Flight Operations Directorate, National Geodetic Survey, USGS Astrogeology Science Center, and NGA and is intended to serve as a resource for all involved with the Artemis missions, as well as for engineers designing and operating lunar infrastructure.

Techniques and Methods↗
USGS2026

Modeled groundwater and surface-water interactions surrounding Mobile Bay, Alabama, 2008–15

The U.S. Geological Survey, in cooperation with the Gulf Coast Ecosystem Restoration Council, has used MODFLOW 6 to develop a groundwater-flow model to simulate groundwater and surface-water interactions in the Mobile Bay, Alabama, area. The model results indicated that, on average, groundwater discharge near the coastline is equal to 2.5 percent of the surface water that flows into the bay. The model was also used to determine how changes in recharge, sea level, and groundwater pumping affect groundwater levels and discharge rates. The results indicate that more groundwater discharge occurred in the winter and spring when recharge was higher, sea level was lower, and groundwater pumping was lower than during the summer and fall. Additionally, the amount of emergent groundwater was closely related to sea level; when sea level was higher, there was more area with emergent groundwater. Furthermore, the depth of nonemergent groundwater was related to trends in recharge and pumping. During periods of increased recharge and reduced pumping, a significant portion of the model area exhibited a depth to the water table of less than 1 meter below the land surface. Conversely, during periods of decreased recharge and heightened pumping, much of the model area showed a depth to the water table ranging from 1 to 5 meters.

Alabama, Mississippi↗
USGS2024

Unscrambling the Proterozoic supercontinent record of northeastern Washington State, USA

The time interval from Supercontinent Nuna assembly in the late Paleoproterozoic to Supercontinent Rodinia breakup in the Neoproterozoic is considered by some geologists to comprise the “Boring Billion,” an interval possibly marked by a slowdown in plate tectonic processes. In northeastern Washington State, USA, similar to much of western Laurentia, early workers generally thought the tectonostratigraphic framework of this interval of geologic time consisted of two major sequences, the (ca. 1480–1380 Ma) Mesoproterozoic Belt Supergroup and unconformably overlying (<720 Ma) Neoproterozoic Windermere Supergroup. However, recent research indicates that strata considered by early workers as Belt Supergroup equivalents are actually younger, and a post-Belt, pre-Windermere record is present within the <1360 Ma Deer Trail Group and <760 Ma Buffalo Hump Formation. Thus, the northeastern Washington region perhaps comprises the most complete stratigraphic record of the “Boring Billion” time interval in the northwestern United States and holds important insights into global Proterozoic supercontinent tectonic processes. In light of these exciting developments, this field guide will address the early historic economic geology and original mapping of these Proterozoic sequences in the northeastern Washington region, and from that foundation explore more recent isotopic provenance data and their regional to global context. Finally, the guide will end with a discussion of remaining questions with a goal of stimulating interest in these relatively understudied, yet important, rocks.

Washington↗
USGS2024

Flood-inundation maps for the Cuyahoga River in and near Independence, Ohio, 2024

Digital flood-inundation maps for a 9.9-mile reach of the Cuyahoga River in and near Independence, Ohio, were created by the U.S. Geological Survey (USGS) in cooperation with the Northeast Ohio Regional Sewer District Board of Trustees. Water-surface profiles were computed for the stream reach by using a one-dimensional steady-state step-backwater model. The model was calibrated to the current (2024) stage-streamflow relation (rating curve 43.0) for the USGS streamgage 04208000, Cuyahoga River at Independence, Ohio. The resulting hydraulic model was then used to compute 13 water-surface profiles for water levels (flood stages) ranging from 14.00 to 26.00 feet. The flood stages range from “action stage” to above “major flood stage” as reported by the National Weather Service. The simulated water-surface profiles were then used in combination with a digital elevation model derived from light detection and ranging data to map the inundated areas associated with each flood profile. The flood-inundation maps and the supporting hydraulic model produced by this study can be used by emergency managers and local officials to assess flood mitigation strategies and to define flood hazard areas to protect life and property, to coordinate flood response activities such as evacuations and road closures, and to aid postflood recovery efforts.

Ohio↗