USGS Science⌕ Search

SEARCH · USGS Science

Results for “Journal of the Nevada Water Resources Association”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,691 records · Page 25Linked to original sources
USGS1996

Hydrogeologic investigation and simulation of ground-water flow in the Upper Floridan Aquifer of north-central Florida and southwestern Georgia and delineation of contributing areas for selected city of Tallahassee, Florida, water-supply wells

A 4-year investigation of the Upper Floridan aquifer and ground-water flow system in Leon County, Florida, and surrounding counties of north-central Florida and southwestern Georgia began in 1990. The purpose of the investigation was to describe the ground-water flow system and to delineate the contributing areas to selected City of Tallahassee, Florida, water-supply wells. The investigation was prompted by the detection of low levels of tetrachloroethylene in ground-water samples collected from several of the city's water-supply wells. Hydrologic data and previous studies indicate that; ground-water flow within the Upper Floridan aquifer can be considered steady-state; the Upper Floridan aquifer is a single water-bearing unit; recharge is from precipitation; and that discharge occurs as spring flow, leakage to rivers, leakage to the Gulf of Mexico, and pumpage. Measured transmissivities of the aquifer ranged from 1,300 ft 2 /d (feet squared per day) to 1,300,000 ft2/d. Steady-state ground-water flow in the Upper Floridan aquifer was simulated using a three-dimensional ground- water flow model. Transmissivities ranging from less than 5,000 ft2/d to greater than 11,000,000 ft 2 /d were required to calibrate to observed conditions. Recharge rates used in the model ranged from 18.0 inches per year in areas where the aquifer was unconfined to less than 2 inches per year in broad areas where the aquifer was confined. Contributing areas to five Tallahassee water-supply wells were simulated by particle- tracking techniques. Particles were seeded in model cells containing pumping wells then tracked backwards in time toward recharge areas. The contributing area for each well was simulated twice, once assuming a porosity of 25 percent and once assuming a porosity of 5 percent. A porosity of 25 percent is considered a reasonable average value for the Upper Floridan aquifer; the 5 percent porosity simulated the movement of ground-water through only solution-enhanced bedding plains and fractures. The contributing areas were generally elliptical in shape, reflecting the influence of the sloping potentiometric surface. The contributing areas delineated for a 5 percent porosity were always much larger than those determined using a 25 percent porosity. The lowest average ground-water velocity computed within a contributing area, using a 25 percent porosity, was 1.0 ft/d (foot per day) and the highest velocity was 1.6 ft/d. The lowest average ground-water velocity, determined using a 5 percent porosity, was 2.4 ft/d and the highest was 7.4 ft/d. The contributing areas for each of the five wells was also determined analytically and compared to the model-derived areas. The upgradient width of the simulated contributing areas were larger than the upgradient width of the analytically determined contributing areas for four of the five wells. The model could more accurately delineate contributing areas because of the ability to simulate wells as partially penetrating and by incorporating complex, three-dimensional aquifer characteristics, which the analytical method could not.

Florida, Georgia↗
USGS2026

Microplastics undergo fragmentation during pressurized membrane filtration

Low-micrometer microplastics (<10 μm) have been detected in drinking water, driving growing interest in using pressure-driven membrane filtration to remove these particles and ensure drinking water safety. However, little attention is paid to the fate of microplastics concentrated in the filtration byproduct. In this study, using well-defined polystyrene (PS) and poly(methyl methacrylate) microspheres as model particles, we observed microplastic fragmentation during nanofiltration and the subsequent release of smaller fragments. After operating for 3 h at 20 bar, 67.9 ± 8.0% of the PS spheres in the concentrate, based on particles counted in selected fields of view, were transformed into fractured particles. The characteristic Raman band signals of microplastics were significantly weakened after fragmentation, leading to detection challenges. To address this, a data processing algorithm was developed to identify PS fragments as small as 1 μm. Preliminary statistical analysis reveals that within the tested pressure range, operation time has a stronger influence on fragmentation than pressure magnitude alone and that fragmentation is further governed by the intrinsic mechanical properties of the tested model polymers. This work provides direct evidence that pressure-driven membrane processes induce microplastic fragmentation and highlights the environmental risks associated with the discharge of fragmented microplastics into the concentrate.

Environmental Science & Technology Letters↗
USGS2021

Factors influencing distribution of Coccidioides immitis in soil, Washington State, 2016

Coccidioides immitis and Coccidioides posadasii are causative agents of Valley fever, a serious fungal disease endemic to regions with hot, arid climate in the United States, Mexico, and Central and South America. The environmental niche of Coccidioide s spp. is not well defined, and it remains unknown whether these fungi are primarily associated with rodents or grow as saprotrophs in soil. To better understand the environmental reservoir of these pathogens, we used a systematic soil sampling approach, quantitative PCR (qPCR), culture, whole-genome sequencing, and soil chemical analysis to identify factors associated with the presence of C. immitis at a known colonization site in Washington State linked to a human case in 2010. We found that the same strain colonized an area of over 46,000 m 2 and persisted in soil for over 6 years. No association with rodent burrows was observed, as C. immitis DNA was as likely to be detected inside rodent holes as it was in the surrounding soil. In addition, the presence of C. immitis DNA in soil was correlated with elevated levels of boron, calcium, magnesium, sodium, and silicon in soil leachates. We also observed differences in the microbial communities between C. immitis -positive and -negative soils. Our artificial soil inoculation experiments demonstrated that C. immitis can use soil as a sole source of nutrients. Taken together, these results suggest that soil parameters need to be considered when modeling the distribution of this fungus in the environment.

Washington↗
USGS1989

Techniques for simulating flood hydrographs and estimating flood volumes for ungaged basins in east and west Tennessee

A dimensionless hydrograph developed for a variety of basin conditions in Georgia was tested for its applicability to streams in East and West Tennessee by comparing it to a similar dimensionless hydrograph developed for streams in East and West Tennessee. Hydrographs of observed discharge at 83 streams in East Tennessee and 38 in West Tennessee were used in the study. Statistical analyses were performed by comparing simulated (or computed) hydrographs, derived by application of the Georgia dimensionless hydrograph, and dimensionless hydrographs developed from Tennessee data, with the observed hydrographs at 50 and 75% of their peak-flow widths. Results of the tests indicate that the Georgia dimensionless hydrography is virtually the same as the one developed for streams in East Tennessee, but that it is different from the dimensionless hydrograph developed for streams in West Tennessee. Because of the extensive testing of the Georgia dimensionless hydrograph, it was determined to be applicable for East Tennessee, whereas the dimensionless hydrograph developed from data on streams in West Tennessee was determined to be applicable in West Tennessee. As part of the dimensionless hydrograph development, an average lagtime in hours for each study basin, and the volume in inches of flood runoff for each flood event were computed. By use of multiple-regression analysis, equations were developed that relate basin lagtime to drainage area size, basin length, and percent impervious area. Similarly, flood volumes were related to drainage area size, peak discharge, and basin lagtime. These equations, along with the appropriate dimensionless hydrograph, can be used to estimate a typical (average) flood hydrograph and volume for recurrence-intervals up to 100 years at any ungaged site draining less than 50 sq mi in East and West Tennessee.

Tennessee↗
USGS2024

Streams, springs, and volcanic lakes for volcano monitoring

Introduction Volcanic unrest can trigger appreciable change to surface waters such as streams, springs, and volcanic lakes. Magma degassing produces gases and soluble salts that are absorbed into groundwater that feeds streams and lakes. As magma ascends, the amount of heat and degassing will increase, and so will any related geochemical and thermal signal. Subsurface magma movement can cause pressurization that alters hydrostatic head and may induce groundwater discharge. Fluid-pressure changes have been linked to distal volcano-tectonic earthquakes (White and McCausland, 2016; Coulon and others, 2017) and phreatic eruptions (for example, Yamaoka and others, 2016). Clearly, changes in groundwater and surface waters are both indicators of unrest and clues to how and where magma is rising toward the surface. Where possible, it is prudent to incorporate real-time hydrologic data into multiparameter monitoring of restless volcanoes. Hydrologic dynamics can also be tracked by changes in groundwater levels that are commonly measured in shallow boreholes (see of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–K, 5 p., https://doi.org/10.3133/sir20245062k. ">chapter K , this volume, on boreholes; Hurwitz and Lowenstern, 2024). Although inferred to be common, relatively few volcano-hydrology anomalies are well documented, and many are essentially anecdotal (Newhall and others, 2001), reflecting the fact that high-resolution time series remain rare. Extreme examples include the 2008 eruption of Nevado del Huila, Colombia, where relatively minor phreatomagmatic eruptions were accompanied by expulsion of as much as 300 million cubic meters of groundwater from fissures high on the volcano (Worni and others, 2011), generating large lahars. Substantial decreases in flow rate from springs about 8 kilometers from the summit of Mayon Volcano, Philippines, have been noted before most eruptions in the 20th century (Newhall and others, 2001). Stream monitoring at Redoubt Volcano in 2009 allowed Werner and others (2012) to recognize that groundwater was unable to absorb (or scrub) the high flux of volcanic gas and that a high CO 2 /SO 2 precursor signal had been evident for 5 months prior to the eruption. A key to better interpreting hydrologic anomalies—or even identifying them—is therefore obtaining adequate baseline data. Most hydrologic monitoring at U.S. volcanoes has been accomplished by intermittent sampling surveys with annual or less frequent sampling (for example, https://hotspringchem.wr.usgs.gov/index.php ). More frequent sampling, however, generally is needed to establish reliable baselines. A recent hydrologic and hydrothermal monitoring experiment at 25 sites and 10 of the 12 level 4 (very high threat) volcanoes in the U.S. portion of the Cascade Range demonstrated that there is sufficient temporal variability in hydrothermal fluxes, even during quiescent periods, that one-time measurements will commonly have limited interpretive value (Crankshaw and others, 2018). Thus, surveys are best augmented with data from streamgages (for example, Evans and others, 2004; Bergfeld and others, 2008). Streamflow (water discharge) data allow measured temperature and specific conductance to be converted to heat and solute mass fluxes, which could be insightful parameters for detecting anomalous activity (McCleskey and others, 2012). At the Yellowstone Caldera, long-term monitoring of river solutes has allowed calculation of the chloride flux, a proxy for heat discharge (Hurwitz and others, 2007; McCleskey and others, 2016) from the subsurface magma. This is readily accomplished because data from streamgages are continuously recorded and archived by the U.S. Geological Survey (USGS) National Water Information System (NWIS) (USGS, 2024). Similar studies on stratovolcanoes or shield volcanoes would be scientifically useful, and yet are logistically challenging, requiring streamgages on numerous radial drainages complemented by either frequent manual sampling or numerous deployments of equipment to measure water temperature and specific conductance as a proxy for water chemistry. Another challenge is that some volcanic areas, especially shield volcanoes, are characterized by near-surface porous rocks and soils, such that surface streams are rare and replaced by distant, dilute large-volume springs with only a trace of any original volcanically sourced water (Manga, 2001; Hurwitz and others, 2021). Volcanic lakes are worthy of special attention for monitoring efforts, as their temperature and composition can provide evidence of increased flux of volatile-rich fluids from below. Quantifying changes in volatile and heat release from magma can be simpler in lakes than for volcanoes with radial drainages and no major lakes. Moreover, volcanic lakes pose a range of hazards themselves, including phreatomagmatic eruptions, debris flows, flank collapse, tsunamis, and toxic gas release (Mastin and Witter, 2000; Delmelle and others, 2015; Manville, 2015; Rouwet and others, 2015)—hazards that have historically been responsible for substantial loss of life at many volcanoes worldwide (Manville, 2015). Catastrophic CO 2 release at Lake Nyos, Cameroon, in 1986 suffocated about 1,750 people and about 3,500 livestock and was probably triggered by a large landslide into the gas-saturated lake (Kling and others, 1987; Evans and others, 1993). Gas-charged springs in Soda Bay within Clear Lake (California) have caused almost a dozen deaths to bathers in the past hundred years (ABC News, 2000). A 2005 example of lake overturn and abundant gas release was documented at Mount Chiginagak in Alaska (Schaefer and others, 2008) but did not result in any human casualties. Although thermally stratified lakes, which promote trapping of exsolved magmatic gas, tend to develop in tropical regions, the phenomenon can also arise where salinity creates meromixis (a condition in which a lake does not mix completely), as occurs in Mono Lake, California (Jellison and Melack, 1993; Jellison and others, 1998). If magma erupts or flows into a lake, the interaction between hot magma and cold water can be explosive (Mastin and others, 2004; Zimanowski and others, 2015) and substantially expand the area affected by the eruption. Another hazard is the breaching of crater rims by landslides triggered by volcanic and (or) seismic activity. Under some circumstances, substantial volumes of water can be displaced, leading to large floods and lahars. Late Holocene lake flooding from Aniakchak Crater in the Alaska Peninsula (Waythomas, 2022) and from Paulina Lake in Newberry Crater, Oregon (Chitwood and Jensen, 2000), caused by the failure of outlet sills, testify to the substantial hazards at lake-filled calderas. Several volcanic systems in the United States host lakes known to receive heat and gas from underlying magma. These lakes vary widely in area, depth, and chemical composition. Lakes are present at level 4 volcanoes, including Crater Lake and Newberry Volcano in Oregon; Yellowstone Caldera in Wyoming; Long Valley Caldera, Clear Lake volcanic field, Medicine Lake, and Salton Buttes in California; and Aniakchak Crater, Mount Katmai, Fisher Caldera, Mount Okmok, and Kaguyak Crater, among others, in Alaska. A water lake was present in Halemaʻumaʻu, the crater of Kīlauea, Hawai‘i (fig. F1), from October 2019 to December 2020. Level 3 volcanoes with lakes include Mono Lake volcanic field (Calif.), Mount Bachelor (Ore.), Ukinrek Maars and Mount Chiginagak (Alaska), and Soda Lake (Nevada). In addition, there are lakes at many levels 1 and 2 volcanoes. In the United States, there are no strongly acidic lakes that receive abundant input of magmatic gas, such as those found at Mount Ruapehu (New Zealand), Ijen and Kelud (Indonesia), and Poás (Costa Rica). Nevertheless, many contain fluids that provide clues to magmatic processes below. Since publication of a previous report on recommended instrumentation for volcano monitoring (Moran and others, 2008), continuous hydrologic monitoring has become increasingly feasible. However, changes in water pressure, temperature, and chemistry remain, in general, poorly studied phenomena at volcanoes (Sparks, 2003; National Academies of Sciences, Engineering, and Medicine, 2017). Recent efforts by the USGS have included the temporary study of Cascade Range volcanoes, which included frequent (15 minute to hourly) temporal sampling of temperature, depth, and conductivity (Crankshaw and others, 2018; Ingebritsen and Evans, 2019). At Yellowstone Caldera, many streamgages have now added thermistors and specific conductance sensors, allowing estimation of time-dependent chloride flux as a proxy for variations in subsurface heat flux (McCleskey and others, 2012, 2016). Efforts to better understand lakes have also accelerated, with bathymetric mapping and sampling carried out at several locations in the United States. Especially thorough work was done at Yellowstone Lake thanks to the Hydrothermal Dynamics of Yellowstone Lake (HD-YLAKE, https://hdylake.org ) project, funded primarily by the National Science Foundation. In addition to geophysical surveys and recovery of cores and other samples, HD-YLAKE investigations included remotely operated vehicle (ROV) investigations of hydrothermal vents on the lake floor (fig. F2). Data collected by the ROV provided a better understanding of the thermal and chemical influx from lake-bottom hydrothermal systems (Sohn and others, 2017). In this chapter, we focus on detecting changes in the chemistry, temperature, discharge, or water levels of streams, springs, and lakes that can be caused by seismicity, volumetric strains, or increases in gas flux associated with ascending magma. There is unavoidable overlap with other chapters of this report. Samples of water and gas can also be obtained in boreholes ( of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–K, 5 p., https://doi.org/10.3133/sir20245062k. ">chapter K , this volume; Hurwitz and Lowenstern, 2024), both shallow and deep. Gas monitoring ( of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–E, 11 p., https://doi.org/10.3133/sir20245062e.">chapter E , this volume; Lewicki and others, 2024) relies in part on samples from springs and wells, particularly where measurable gas plumes are absent. Water acts as a trigger and lubricant for landslides and sediment-rich floods, and so hydrology has obvious relevance for lahar monitoring, as discussed in of Flinders, A.F., Lowenstern, J.B., Coombs, M.L., and Poland, M.P., eds., Recommended capabilities and instrumentation for volcano monitoring in the United States: U.S. Geological Survey Scientific Investigations Report 2024–5062–H, 6 p., https://doi.org/10.3133/sir20245062h. ">chapter H (this volume; Thelen and others, 2024). Shared situational awareness among scientists engaged in geophysical, gas, and hydrologic monitoring will improve overall understanding of the volcanic hazard.

Scientific Investigations Report↗
USGS2026

Assessing the state of hydrologic science in the Upper Klamath Basin—A comprehensive review of data, tools, and models

Water demand in the Upper Klamath Basin (UKB) from various stakeholders and ecological needs often outstrips available supply, leading to persistent management challenges. This study reviews the state of hydrologic science within the UKB as of 2025—specifically, the tools, data, and models available for assessing five key components of the water system: (1) surface water; (2) precipitation; (3) evapotranspiration; (4) groundwater; and (5) water use. The UKB water supply is critical for Native American communities, regional agriculture, and federally listed fishes and faces challenges from competing needs, climate variability, and operational/regulatory requirements. We assess existing datasets, regional and national models, and historical studies to understand the available resources and identify gaps that may hinder integrated water assessments and management. Our findings indicate areas where improvements in data collection and model precision could improve the accuracy of water-availability forecasts and support water-management practices. This review can inform near-term forecasting, assist in optimizing water-resource data collection and management strategies, and support regional water-availability assessments of the basin.

Oregon↗
USGS2025

Nodal seismic deployment on Mauna Loa volcano, Hawaii: Dataset and preliminary insights

Mauna Loa is the largest active volcano on Earth, comprising ∼51% of the Island of Hawai‘i’s landmass and posing significant risks to the island’s communities, infrastructure, and natural environment. Historical eruptions have produced lava flows that have reached the ocean in as little as 3 hr. The timing and location of such lava flows in the past 200 yr underscore how critical determination of the location and geometry of magma storage and structure is for volcanic hazard assessment and eruption forecasting. Now, after nearly 38 yr of volcanic quiescence, Mauna Loa has erupted again. On 27 November 2022, fissures initiated within the summit caldera and then migrated to the northeast rift zone, where they generated a large lava flow that threatened a major highway. To improve our understanding of the geometry of this magma system, we deployed a temporary nodal array on Mauna Loa in the summer of 2024. This increased our seismic coverage sufficiently to image this magmatic system. This nodal array consists of 33 seismometers distributed on and around the volcano and was deployed for over three months to record seismic signals. The primary objective of this project is to resolve the high‐resolution seismic velocity structure and characterize seismic features associated with magma storage and ascent pathways. In this article, we present an overview of the deployment, evaluate the quality of the data, and show example recordings to evaluate the suitability of the data set for future seismic investigations, including earthquake relocation, seismic tomography, and receiver function analysis. Comparisons with nearby permanent broadband and short‐period seismic stations demonstrate that the nodal array recorded high‐quality waveforms, making it a valuable resource for constraining the magmatic system beneath Mauna Loa at multiple scales.

Hawaii↗
USGS2025

Hydrogeologic investigation, framework, and conceptual flow model of the Antlers aquifer, southeastern Oklahoma, 1980–2022

The 1973 Oklahoma Groundwater Law (Oklahoma Statute §82–1020.5) requires that the Oklahoma Water Resources Board conduct hydrologic investigations of the State’s groundwater basins to support a determination of the maximum annual yield for each groundwater basin. Every 20 years, the Oklahoma Water Resources Board is required to update the hydrologic investigation on which the maximum annual yield determinations were based. The maximum annual yield allocated per acre of land is used to set the equal-proportionate share pumping rate. The maximum annual yield of 5,913,600 acre-feet per year and equal-proportionate-share of 2.1 acre-feet per acre per year currently (2025) in place for the Antlers aquifer were issued by the Oklahoma Water Resources Board on February 14, 1995. Because more than 20 years have elapsed since the 1995 final order for the Antlers aquifer was issued, the U.S. Geological Survey, in cooperation with the Oklahoma Water Resources Board, completed an in-depth hydrologic study that included a hydrogeologic framework and conceptual groundwater-flow model for the 1980–2022 study period. The results of an analysis of land use, long-term climate patterns, streamflow and base-flow patterns, historical groundwater use, as well as groundwater-level fluctuations across the Antlers aquifer are described. In addition, groundwater quality was analyzed for total dissolved solids concentrations and major ions for the Antlers aquifer. An updated hydrogeologic framework was developed that included refining the aquifer boundary in Oklahoma, the creation of new potentiometric surface and saturated thickness of fresh groundwater maps, one multiple-well aquifer test, slug tests, and an analysis of lithologic logs across the aquifer. A conceptual groundwater flow model and water budget were developed by incorporating estimates of recharge from precipitation, saturated-zone evapotranspiration, streambed seepage, lateral groundwater flows, vertical leakage, and withdrawals from groundwater wells.

Oklahoma, Texas↗
USGS1989

An investigation of shallow ground-water quality near East Fork Poplar Creek, Oak Ridge, Tennessee

Alluvial soils and fill materials in and near the floodplain of East Fork Poplar Creek in Oak Ridge, Tennessee, are contaminated with various trace metals (primarily mercury), organic compounds, and radionuclides that were lost to the stream as a result of past operations at the Y-12 Plant, a nuclear-processing facility located within the U.S. Department of Energy’s Oak Ridge Reservation. Observation wells were installed in the shallow (above bedrock) aquifer in and near the floodplain of East Fork Poplar Creek and water-quality samples were collected to determine if contaminants found in the soils and fill are also present in the shallow ground water. The shallow aquifer in the East Fork Poplar Creek flood plain consists primarily of alluvial silt and clay with lesser amounts of sand and gravel. Thickness of the shallow aquifer ranges from essentially zero to as much as 20 feet. A silty-clay glei horizon is present between the base of the alluvium and the top of bedrock at most flood-plain locations and, where present, likely impedes downward ground-water movement. Water in the shallow aquifer near East Fork Poplar Creek occurs under water-table conditions. Recharge to the shallow aquifer is principally from precipitation, and discharge is through springs and seeps to East Fork Poplar Creek and its tributaries. During spring, summer; and fall, evapotranspiration also accounts for the removal of water in storage in the shallow aquifer. Water levels in the shallow aquifer fluctuate seasonally in response to variations in recharge and evapotranspiration. Generally, the depth to water in the observation wells ranged from about 1 to 4 feet below land surface in late winter, and from about 2 to 7 feet below land surface in late fall. During extremely dry periods, the water table recedes below the top of bedrock in some flood-plain areas, possibly causing East Fork Poplar Creek to lose water to the shallow aquifer along some reaches. Contaminants found in water samples collected from several of the observation wells in concentrations (total and (or) total-recoverable) which equaled or exceeded drinking-water standards established by the U.S. Environmental Protection Agency are antimony, chromium, lead, mercury, selenium, total phenols, and strontium-90. Total and dissolved uranium concentrations exceeded 1.0 microgram per liter in samples from nearly 70 percent of the wells in the East Fork Poplar Creek flood plain. Organic compounds that were identified in low concentrations in samples from a few wells in the flood plain are: Arochlor 1260, benzo(a)anthracene, benzo(b)fluoranthene, chrysene, 3,3-dichlorobenzidine, di-n-butylphthalate, N-nitrosodiphenylamine, and pyrene. Water from one well in the East Fork Poplar Creek flood plain at a contaminated fill site contained 37and 8 micrograms per liter of trichloroethene and trans-1,2-dichloroethene, respectively. Comparison of the results of total and (or) total-recoverable trace-metal determinations with those from dissolved determinations demonstrates that elevated concentrations of these substances in water collected from several of the wells in the East Fork Poplar Creek flood plain resulted from sorption of trace metals (and possibly organic compounds and radionuclides) by fine sediment suspended in the samples. The occurrence of contaminated sediment in these samples is suspected to be the result of borehole contamination during well installation.

Tennessee↗
USGS2000

Stormflow chemistry in the Santa Ana River below Prado Dam and at the diversion downstream from Imperial Highway, southern California, 1995-98

The Santa Ana River drains about 2,670 square miles of the densely populated coastal area of southern California, near Los Angeles. Almost all the flow in the river, more than 200,000 acre-feet annually, is diverted into ponds where it infiltrates and recharges underlying aquifers. About 2 million people are dependent on these aquifers for water supply. Stormflow in the Santa Ana River is considered a source of "high-quality" water suitable for use as a source of ground-water recharge. To test this assumption, stormflow samples were collected at two locations--below Prado Dam and at the diversion point downstream from Imperial Highway--for 12 winter storms between 1995 and 1998. Nitrate concentrations decreased during stormflow from a median concentration of 7.8 milligrams per liter in base flow to concentrations less than 1 milligram per liter in some large storms. Concentrations of chemically reduced forms of nitrogen (nitrite, ammonia, and organic nitrogen) increased during stormflow and are the predominant forms of nitrogen in large stormflows. Dissolved organic carbon (DOC) concentrations increased from a median concentration of 4.6 milligrams per liter in base flow to more than 20 milligrams per liter in some stormflows. Concentrations of DOC were especially high during the first storm of the rainy season, and large increases in DOC concentrations were measured even as a result of small early season storms that did not cause large increases in streamflow. DOC present during early season stormflow had less ultraviolet absorbance at 254 nanometers (UV 254 ) per unit of carbon than did DOC from late season stormflows. DOC in water held in storage behind Prado Dam had the highest UV 254 absorbance per unit of carbon. Maximum pesticide concentrations in stormflow did not exceed U.S. Environmental Protection Agency Maximum Contaminant Levels. Most pesticide concentrations were less than 1 microgram per liter and less than the detection limits obtained using standard drinking water analyses. Increases in concentrations of pesticides such as diazinon, malathion, and chlorpyrifos in stormflow result from runoff from urban areas downstream from Prado Dam. In general, large late season stormflows have the most pesticide detections of all stormflows sampled. Concentrations of methyl tert-butyl ether (MTBE), a gasoline additive, during base flow were as high as 0.9 microgram per liter and concentrations decreased during stormflow. Like pesticides, the concentrations did not exceed the U.S. Environmental Protection Agency Maximum Contaminant Levels for MTBE.

California↗
USGS1998

Ground-water flow in the surficial aquifer system and potential movement of contaminants from selected waste-disposal sites at Naval Station Mayport, Florida

Ground-water flow through the surficial aquifer system at Naval Station Mayport near Jacksonville, Florida, was simulated with a two-layer finite-difference model as part of an investigation conducted by the U.S. Geological Survey. The model was calibrated to 229 water-level measurements from 181 wells during three synoptic surveys (July 17, 1995; July 31, 1996; and October 24, 1996). A quantifiable understanding of ground-water flow through the surficial aquifer was needed to evaluate remedial-action alternatives under consideration by the Naval Station Mayport to control the possible movement of contaminants from sites on the station. Multi-well aquifer tests, single-well tests, and slug tests were conducted to estimate the hydraulic properties of the surficial aquifer system, which was divided into three geohydrologic units�an S-zone and an I-zone separated by a marsh-muck confining unit. The recharge rate was estimated to range from 4 to 15 inches per year (95 percent confidence limits), based on a chloride-ratio method. Most of the simulations following model calibration were based on a recharge rate of 8 inches per year to unirrigated pervious areas. The advective displacement of saline pore water during the last 200 years was simulated using a particle-tracking routine, MODPATH, applied to calibrated steady-state and transient models of the Mayport peninsula. The surficial aquifer system at Naval Station Mayport has been modified greatly by natural and anthropogenic forces so that the freshwater flow system is expanding and saltwater is being flushed from the system. A new MODFLOW package (VAR1) was written to simulate the temporal variation of hydraulic properties caused by construction activities at Naval Station Mayport. The transiently simulated saltwater distribution after 200 years of displacement described the chloride distribution in the I-zone (determined from measurements made during 1993 and 1996) better than the steady-state simulation. The advective movement of contaminants from selected sites within the solid waste management units to discharge points was simulated using MODPATH. Most of the particles were discharged to the nearest surface-water feature after traveling less than 1,000 feet in the ground-water system. Most areas within 1,000 feet of a surface-water feature or storm sewer had traveltimes of less than 50 years, based on an effective porosity of 40 percent. Contributing areas, traveltimes, and pathlines were identified for 224 wells at Naval Station Mayport under steady-state and transient conditions by back-tracking a particle from the midpoint of the wetted screen of each well. Traveltimes to contributing areas that ranged between 15 and 50 years, estimated by the steady-state model, differed most from the transient traveltime estimates. Estimates of traveltimes and pathlines based on steady-state model results typically were 10 to 20 years more and about twice as long as corresponding estimates from the transient model. The models differed because the steady-state model simulated 1996 conditions when Naval Station Mayport had more impervious surfaces than at any earlier time. The expansion of the impervious surfaces increased the average distance between contributing areas and observation wells.

Florida↗
USGS1992

Nonpoint-source pollutant discharges of the three major tributaries to Reelfoot Lake, west Tennessee, October 1987-September 1989

An investigation of the concentration and loads of nitrogen, phosphorus, and suspended sediment in storm runoff to Reelfoot Lake, in western Tennessee, was conducted from October 1987 through September 1989. Concentrations of selected herbicides also were defined. Reelfoot Lake, with a surface area of about 15,500 acres, is the largest natural lake in Tennessee and an important recreation and fisheries resource. Previous studies showed that the lake is hypereutrophic, a condition caused by high concentrations of nutrients in water and sediments discharged from the three principal tributaries (South Reelfoot Creek, North Reelfoot Creek, and Running Slough) to the lake. Pesticides, including herbicides, have been detected in the lake's bottom sediments. Storm runoff contributed about 87percent of the total water discharge of the three main tributaries to Reelfoot Lake. South Reelfoot Creek contributed about 4.7 tons per acre per year of suspended sediment, while North Reelfoot Creek contributed about 1.9 tons per acre per year. Running Slough contributed only about 0.31 ton per acre per year of suspended sediment. Most of the suspended sediment was transported by storm runoff between October and March. About 80 percent of the annual streamflow of the three tributaries occurs during these months. The North Reelfoot Creek basin contributed 8.2 pounds per acre per year of total nitrogen and 2.4 pounds per acre per year of total phosphorus. South Reelfoot Creek basin contributed about 6.5 and 1.3 pounds per acre per year of total nitrogen and phosphorus, respectively, while Running Slough basin contributions were 3.4 and 0.86 pounds per acre per year, respectively. The differences in nutrient yields appear to result from more row-crop agriculture and the relatively steeply sloping agricultural land in the North Reelfoot Creek basin. Ninety-one percent of the total nitrogen load and 95 percent of the total phosphorus load in the three streams was transported by storm runoff. Significant differences in the mean concentrations of nutrients in runoff were defined between the active agricultural months (April through September) and the inactive months (October through March). Storm-runoff samples were analyzed for II selected triazine herbicides. Alachlor and atrazine were the most commonly detected herbicides. Thirty-two percent of the samples contained detectable levels of alachlor and 93 percent of the samples contained detectable levels of atrazine. Ninety percent of the samples collected during the active agricultural months contained detectable leveki of alachlor and all 29 samples contained detectable levels of atrazine. Sixteen samples exceeded lifetime health-advisory levels for atrazine in drinking water (3 micrograms per liter); two samples collected from the April IS, 1988, storm at North Reelfoot Creek and South Reelfoot Creek contained 42 and 57 micrograms per liter of atrazine, respectively. Concentrations of the other nine triazine herbicides were generally less than the level of detection (0.1 microgram per liter).

Tennessee↗
USGS1990

Recharge rates and aquifer hydraulic characteristics for selected drainage basins in middle and east Tennessee

Quantitative information concerning aquifer hydrologic and hydraulic characteristics is needed to manage the development of ground-water resources. These characteristics are poorly defined for the bedrock aquifers in Middle and East Tennessee where demand for water is increasing. This report presents estimates of recharge rate, storage coefficient, diffusivity, and transmissivity for representative drainage basins in Middle and East Tennessee, as determined from analyses of stream-aquifer interactions. The drainage basins have been grouped according to the underlying major aquifer, then statistical descriptions applied to each group, in order to define area1 distribution of these characteristics. Aquifer recharge rates are estimated for representative low, average, and high flow years for 63 drainage basins using hydrograph analysis techniques. Net annual recharge during average flow years for all basins ranges from 4.1 to 16.8 in/yr (inches per year), with a mean value of 7.3 in. In general, recharge rates are highest for basins underlain by the Blue Ridge aquifer (mean value11.7 in/yr) and lowest for basins underlain by the Central Basin aquifer (mean value 5.6 in/yr). Mean recharge values for the Cumberland Plateau, Highland Rim, and Valley and Ridge aquifers are 6.5, 7.4, and 6.6 in/yr, respectively. Gravity drainage characterizes ground-water flow in most surficial bedrock aquifer in Tennessee. Accordingly, a gravity yield analysis, which compares concurrent water-level and streamflow hydrographs, was used to estimate aquifer storage coefficient for nine study basins. The basin estimates range from 0.002 to 0.140; however, most estimates are within a narrow range of values, from 0.01 to 0.025. Accordingly, storage coefficient is estimated to be 0.01 for all aquifers in Middle and East Tennessee, with the exception of the aquifer in the inner part of the Central Basin, for which storage coefficient is estimated to be 0.002. Estimates of aquifer hydraulic diffusivity are derived from estimates of the streamflow recession index and drainage density for 75 drainage basins; values range from 3,300 to 130,000 ft^2/d (feet squared per day). Basin-specific and site-specific estimates of transmissivity are computed from estimates of hydraulic diffusivity and specific-capacity test data, respectively. Basin-specific, or areal, estimates of transmissivity range from 22 to 1,300 ft^2/d, with a mean of 240 ft^2/d In general, areal transmissivity is highest for basins underlain by the Cumberland Plateau aquifer (mean value 480 ft^2/d) and lowest for basins underlain by the Central Basin aquifer (mean value 79 ft^2/d). Mean transmissivity values for the Highland Rim, Valley and Ridge, and Blue Ridge aquifer are 320,140, and 120 ft^2/d respectively. Site-specific estimates of transmissivity, computed from specific-capacity data from 118 test wells in Middle and East Tennessee range from 2 to 93,000 ft^2/d with a mean of 2,600 ft^2/d Mean transmissivity values for the Cumberland Plateau, Highland Rim, Central Basin, Valley and Ridge, and Blue Ridge aquifers are 2,800,1,200, 7,800, 390, and 65Oft Id, respectively.

Tennessee↗
USGS2025

Ordovician stratigraphy, structure, and karst of the Falling Spring Valley, Alleghany County, Virginia, USA

This one-day trip highlights new findings on a preliminary bedrock geologic map that shows results from ongoing geologic mapping in the Falling Spring Valley of Alleghany County, Virginia, USA, which is the southern end of the larger Warm Springs Valley, an elongated anticlinal valley rimmed by Ordovician and Silurian siliciclastic rocks, and which is famous for its thermal springs. This mapping includes stratigraphic, structural, and karst field and lab research focused on the Ordovician strata exposed in the area, the oldest of which is the dolomitic upper part of the Beekmantown Formation (Lower Ordovician, Darriwilian), and the youngest of which is the Juniata Formation (Upper Ordovician, Katian), a sequence of siliciclastic redbeds. Warm Springs Valley is the location of the only known caves in the eastern United States—three at present—with thermal waters flowing in some of their passages. Stops on the trip will highlight key details from mapping efforts, primarily within the structurally deformed Ordovician carbonate sequence that is exposed in the core and limbs of the anticline, as well as the associated karst features that are developed in those carbonate rocks, including results of recent dye traces and water temperature monitoring that have improved our understanding of the karst hydrogeologic systems developed in these strata.

Virginia↗
USGS2021

Virginia and Landsat

From the shores of Jamestown and spreading north, south, and west, the lands that became the State of Virginia were some of the first in North America top experience rapid landscape change from European settlement. Imagery and data from the USGS Landsat series of satellites offer an unparalleled resource for the study, understanding, and preservation of Virginia’s land and water resources. From monitoring the health of water bodies to managing invasive species to planning for a range of climate change effects, the USGS National Land Imaging Program’s stewardship and public delivery of Landsat data have benefitted Virginians in myriad ways.

Virginia↗
USGS2000

Use of a ground-penetrating radar system to detect pre- and post-flood scour at selected bridge sites in New Hampshire, 1996-98

Ground-penetrating radar was used to measure the depth and extent of existing and infilled scour holes and previous scour surfaces at seven bridges in New Hampshire from April 1996 to November 1998. Ground-penetrating-radar survey techniques initially were used by the U.S. Geological Survey to study streambed scour at 30 bridges. Sixteen of the 30 bridges were re-surveyed where floods exceeded a 2-year recurrence interval. A 300-megahertz signal was used in the ground-penetrating radar system that penetrated through depths as great as 20 feet of water and as great as 32 feet of streambed materials. Existing scour-hole dimensions, infilled thickness, previous scour surfaces, and streambed materials were detected using ground-penetrating radar. Depths to riprap materials and pier footings were identified and verified with bridge plans. Post data-collection-processing techniques were applied to assist in the interpretation of the data, and the processed data were displayed and printed as line plots. Processing included distance normalization, migration, and filtering but processing was kept to a minimum and some interference from multiple reflections was left in the record. Of the 16 post-flood bridges, 22 ground-penetrating-radar cross sections at 7 bridges were compared and presented in this report. Existing scour holes were detected during 1996 (pre-flood) data collection in nine cross sections where scour depths ranged from 1 to 3 feet. New scour holes were detected during 1998 (post-flood) data collection in four cross sections where scour depths were as great as 4 feet deep. Infilled scour holes were detected in seven cross sections, where depths of infilling ranged from less than 1 to 4 feet. Depth of infilling by means of steel rod and hammer was difficult to verify in the field because of cobble and boulder streambeds or deep water. Previous scour surfaces in streambed materials were identified in 15 cross sections and the depths to these surfaces ranged from 1 to 10 feet below the streambed. Riprap materials or pier footings were identified in all cross sections. Calculated record depths generally agree with bridge plans. Pier footings were exposed at two bridges and steel pile was exposed at one bridge. Exposures were verified by field observations.

New Hampshire↗
USGS2000

Natural attenuation of chlorinated volatile organic compounds in ground water at Area 6, Naval Air Station Whidbey Island, Washington

Natural attenuation is a viable alternative to pump and treat for meeting remediation objectives in the vicinity of the southern contaminant plume. The combination of historically low contaminant concentrations in ground water, a landfill cap that limits source area contributions, favorable conditions for degradation of VC, and a relatively long downgradient distance to potential receptors are all favorable for natural attenuation as a remediation alternative. Natural attenuation could effectively meet all but one remediation goal that extraction wells PW- 2, PW-4, PW-6, PW-7, PW-8 and PW-9 are currently being employed to meet. The goal of preventing migration of all VC across the site boundary could not be met by natural attenuation. Some VC would migrate south of the Navy boundary, but the potential for subsequent VC mineralization downgradient of the base and the existing institutional controls would result in minimal additional risk from using natural attenuation. In the western contaminant plume natural attenuation is not currently a viable alternative to pump and treat for meeting remediation objectives. There is a possibility that rates for reductive dechlorination of TCE and TCA could increase substantially if the plume was allowed to migrate beneath the Oak Harbor landfill, but there are not enough data to be certain of such an increase. TCA and TCE concentrations at the leading edge of the western plume need to be reduced to at least 25 and 40 µg/L, respectively, to be protective of potential downgradient receptors. Source area TCA and TCE concentrations have decreased substantially over the past ten years, and the extraction wells PW-3 and PW-5 in particular are removing a significant mass of contaminants from ground water, so natural attenuation may be a viable alternative for the western plume in the future. There would be some possible side benefits of using natural attenuation as an alternative to pump and treat in the southern contaminant plume. The first would be that the resulting decrease in the amount of treated water that would need to be recharged in the swale north of the landfill would result in less off-base migration of contamination across the western site boundary. The second benefit would be a substantial reduction in the amount of dissolved iron and manganese being extracted from the shallow aquifer and run through the treatment system. Removing that source of operation and maintenance problems would result in more effective containment and removal of contamination in the western contaminant plume. The most critical data gap identified in this evaluation is the paucity of contaminant chemistry information downgradient of the Navy boundary in the vicinity of the southern contaminant plume. Without such data, the behavior of the plume and the protectiveness of natural attenuation to downgradient receptors cannot be verified, and field attenuation rates for VC cannot be determined directly. The existing long-term monitoring plan would need to be reviewed and revised if natural attenuation is selected as a remedy for the contamination in the southern plume. In particular, additional performance monitoring wells may be required downgradient of the property.

Washington↗
USGS2024

Quality of groundwater used for domestic supply in the eastern Sacramento Valley and adjacent foothills, California

Summary More than 2 million Californians rely on groundwater from privately owned domestic wells for drinking-water supply. This report summarizes a water-quality survey of domestic and small-system drinking-water supply wells in the eastern Sacramento Valley and adjacent foothills where more than 25,000 residents are estimated to use privately owned domestic wells. Study results show that inorganic and organic constituents in groundwater were present above regulatory (maximum contaminant level, MCL) benchmarks for public drinking-water quality in 8 and 3 percent, respectively, of the aquifer area used for domestic drinking-water supply (herein, “domestic groundwater resources”; fig. 1). The only inorganic constituent detected above regulatory benchmarks was arsenic. The only organic constituent exceeding regulatory benchmarks was the fumigant 1,2,3-trichloropropane (1,2,3-TCP). Three additional organic constituents—the disinfection by-product chloroform, the gasoline oxygenate methyl tert -butyl ether (MTBE), and the solvent tetrachloroethene (PCE)—were detected at low concentrations below one-tenth of regulatory benchmarks in 34, 10, and 10 percent of domestic groundwater resources, respectively. Total dissolved solids (TDS), iron, and manganese exceeded non-regulatory aesthetic guidelines for drinking water in 5, 10, and 26 percent of domestic groundwater resources, respectively. Per- and polyfluoroalkyl substances (PFASs) were detected in 29 percent of domestic groundwater resources,with 5 percent exceeding the recently enacted (April 2024) U.S. Environmental Protection Agency MCLs. Total coliform and enterococci bacteria were detected in 13 and 8 percent of domestic groundwater resources, respectively. Redox sensitive constituents in this study included arsenic, manganese, nitrate, and iron. In the lower elevation portions of the eastern Sacramento Valley study area, reducing conditions in groundwater aquifers promote elevated arsenic, iron, and manganese, and conversely lower concentrations of nitrate. The presence of the volatile organic compound (VOC) 1,2,3-TCP was related to its past history in select agricultural land uses (on orchards or vineyards) in the Sacramento Valley; however, unlike in the San Joaquin Valley where orchards and vineyards are more common, its detection frequency was low (only detected in one well in this study). Chloroform was frequently detected in this study at low levels. Chloroform is a disinfection byproduct commonly found in domestic wells treated by shock chlorination. The solvent PCE is among the most frequently detected VOCs in groundwater, which is primarily related to its long history of use and its persistence in groundwater in oxic conditions. The gasoline oxygenate MTBE was a contaminant introduced to groundwater through atmospheric exchange when it was used as a fuel additive to decrease smog inducing emissions from vehicles. Its occurrence in groundwater at low levels is expected and makes it a potentially useful tracer of relatively recent recharge water being withdrawn from wells. The PFASs are anthropogenic chemicals with hundreds of uses, and they have been incorporated into many different products, processes, and applications worldwide. Like MTBE, the occurrence of PFASs in groundwater may be in part due to atmospheric exchange, but there are several other pathways that contribute PFASs to the environment.

California↗