USGS Science⌕ Search

SEARCH · USGS Science

Results for “Journal of Applied Volcanology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,659 records · Page 20Linked to original sources
USGS2000

Water quality of selected springs and public-supply wells, Pine Ridge Indian Reservation, South Dakota, 1992-97

This report presents results of a water-quality study for the Pine Ridge Indian Reservation, South Dakota. The study was a cooperative effort between the U.S. Geological Survey and the Water Resources Department of the Oglala Sioux Tribe. Discharge and water-quality data were collected during 1992-97 for 14 contact springs located in the northwestern part of the Reservation. Data were collected to evaluate potential alternative sources of water supply for the village of Red Shirt, which currently obtains water of marginal quality from a well completed in the Inyan Kara aquifer. During 1995-97, water-quality data also were collected for 44 public-supply wells that serve about one-half of the Reservation's population. Quality-assurance sampling was used to evaluate the precision and accuracy of environmental samples. Ten of the springs sampled contact the White River Group, and four contact the Pierre Shale. Springs contacting the White River Group range from calcium bicarbonate to sodium bicarbonate water types. Two springs contacting the Pierre Shale have water types similar to this; however, sulfate is the dominant anion for the other two springs. In general, springs contacting the White River Group are shown to have better potential as alternative sources of water supply for the village of Red Shirt than springs contacting the Pierre Shale. Nine of the springs with better water quality were sampled repeatedly; however, only minor variability in water quality was identified. Six of these nine springs, of which five contact the White River Group, probably have the best potential for use as water supplies. Discharge from any of these six springs probably would provide adequate water supply for Red Shirt during most periods, based on a limited number of discharge measurements collected. Concentrations of lead exceeded the U.S. Environmental Protection Agency (USEPA) action level of 15 µg/L for three of these six springs. Five of these six springs also had arsenic concentrations that exceeded 10 µg/L, which could be problematic if the current maximum contaminant level (MCL) is lowered. Blending of water from one or more springs with water from the existing Inyan Kara well may be an option to address concerns regarding both quantity and quality of existing and potential sources. All nine springs that were sampled for indicator bacteria had positive detections on one or more occasions during presumptive tests. Although USEPA standards for bacteria apply only to public-water supplies, local residents using spring water for domestic purposes need to be aware of the potential health risks associated with consuming untreated water. One spring contacting the White River Group and two springs contacting the Pierre Shale exceeded 15 pCi/L for gross alpha; these values do not necessarily constitute exceedances of the MCL, which excludes radioactivity contributed by uranium and radon. Additional sampling using different analysis techniques would be needed to conclusively determine if any samples exceeded this MCL. Nine springs were sampled for selected pesticides and tritium. The pesticides atrazine, carbaryl, and 2,4-D were not detected in any of the samples. The nine springs were analyzed for tritium in order to generally assess the age of the water and to determine if concentrations exceeded the MCL established for gross beta-particle activity. Tritium results indicated two springs are composed primarily of water recharged prior to atmospheric testing of nuclear bombs and two other springs have a relatively large percentage of test-era water. The remaining five springs had tritium values that indicated some percentage of test-era water; however, additional sampling would be needed to determine whether water is predominantly pre- or post-bomb age. Of the 44 public-supply wells sampled, 42 are completed in the Arikaree aquifer, one is completed in an alluvial aquifer, and one is completed in the Inyan Kara aquifer. Water from the alluvial well is a sodium bicarbonate water type, water from Arikaree aquifer ranges from calcium bicarbonate to sodium bicarbonate types, and water from the Inyan Kara well is a calcium sulfate bicarbonate type. Of the 44 wells sampled, 28 (64 percent) tested positive for indicator bacteria in presumptive tests. Because these were single samples that generally were collected upstream from chemical treatment feeders, positive detections do not necessarily constitute exceedances of drinking-water standards. A single sample from an Arikaree well exceeded the MCL for arsenic of 50 µg/L. Arsenic exceeded 10 µg/L for six additional Arikaree wells and for the alluvial well and the Inyan Kara well, which could be problematic if the current MCL is lowered. The alluvial well also exceeded the secondary maximum contaminant level (SMCL) for dissolved solids, which is non-enforceable, and the action level for lead. The Inyan Kara well exceeded the SMCL's for iron and for manganese and the MCL of 5 pCi/L for radium-226 and 228 combined. Several Arikaree wells exceeded SMCL's for either pH, sulfate, dissolved solids, iron, or manganese. One Arikaree well exceeded the MCL of 4.0 mg/L for fluoride and another exceeded the MCL of 10 mg/L for nitrite plus nitrate. Ten Arikaree wells equalled or exceeded 15 pCi/L for gross alpha; however, these values do not necessarily constitute exceedances of the MCL, which excludes radioactivity contributed by uranium and radon. Additional sampling using different analysis techniques would be needed to conclusively determine if any samples exceeded this MCL. Eight wells, all from the Arikaree aquifer, equalled or exceeded the proposed MCL of 20 µg/L for uranium and 33 wells (75 percent) equalled or exceeded one-half of the proposed MCL. Although this standard has only been proposed, additional information regarding the extent of elevated uranium concentrations in the Arikaree aquifer, and the geochemical processes involved, may be beneficial. It was determined from analyses of uranium isotope data for five wells that the source of elevated uranium concentrations is naturally occurring, rather than anthropogenic.

South Dakota↗
USGS2024

Simulation of groundwater flow and brine discharge to the Dolores River in the Paradox Valley, Montrose County, Colorado

Salinity, or total dissolved solids (TDS), of the Colorado River affects agricultural, municipal, and industrial water users and is an important concern in the Western United States. In the Paradox Valley of southwestern Colorado, natural discharge of sodium-chloride brine to the Dolores River from the underlying core of a salt-valley anticline accounts for about 6 percent of the salinity load to the Colorado River. Formation of the Paradox Valley began during the Miocene, and subsequent erosion exposed the Pennsylvania Paradox Formation in the core of the anticline where a cap rock, collapse features, breccia, and sodium-chloride saturated brine developed at the top of the exposed salt diapir. The discharge of brine to the Dolores River is affected by these dissolution features, along with seasonal hydrologic conditions and density-dependent flow between older dense brine and the younger fresh groundwater in the overlying alluvial aquifer. To reduce TDS concentrations in the Dolores River through the Paradox Valley, the Bureau of Reclamation has pumped brine from a series of shallow wells adjacent to the river since July 1996. The pumped brine is collected and piped to a deep disposal well where it is injected into the Mississippian Leadville Limestone at a depth of about 4,570-meters below land surface. The pumping and injection operation is collectively known as the Paradox Valley Unit (PVU), and by 2015, the PVU had substantially reduced TDS concentrations in the Dolores River by about 70 percent. Since 2019, injection-pressure limits and related seismic activity have constrained deep-well injection and thus brine pumping at the PVU. In cooperation with the Bureau of Reclamation, the U.S. Geological Survey developed a MODFLOW-6 three-dimensional, variable-density groundwater flow and TDS transport model of the Paradox Valley to evaluate the effects of PVU pumping operations on brine discharge to the Dolores River and to guide additional research. The finite-difference model grid consists of 76 rows and 48 columns oriented from northwest to southeast in alignment with valley topography and groundwater-flow directions in the near-surface freshwater alluvial aquifer. A 7-layer hydrogeologic framework was developed from existing datasets to represent the alluvial aquifer, cap rock, collapse breccia, and groundwater flow and TDS transport from the underlying Paradox Formation salt to the Dolores River. The model represents a 33-year transient calibration period from 1987 through 2020 that includes pre-PVU conditions from 1987 through June 1996 and post-PVU conditions from July 1996 through 2020. A 1,000-year simulation of groundwater flow and coupled TDS transport computed the initial conditions for the subsequent 33-year transient simulation. Observations of precipitation, streamflow, evaporation, agricultural land use, and PVU brine pumping rates were used to specify appropriate boundary conditions to the model representing time-varying recharge, tributary streamflow, groundwater underflow, evapotranspiration (ET), and PVU pumping. Values for average monthly streamflow and TDS concentration at the upstream streamgage, the Dolores River at Bedrock (USGS streamgage 09169500), were specified as model input where the Dolores River enters Paradox Valley. Observed pumping from the PVU, water levels and TDS concentrations in groundwater, and streamflow and estimated TDS concentrations at the downstream streamgage, the Dolores River near Bedrock (USGS streamgage 09171100), were calibration targets that constrained the manual calibration of model parameters representing aquifer hydraulic conductivity, storage, streambed conductance, recharge, and (ET). Two primary model-calibration targets were the match between observed and simulated TDS mass flux from PVU pumping wells and the match between estimated and simulated TDS mass flux to the Dolores River. The simulated TDS mass withdrawn by pumping wells is calculated by the model as the product of the assigned pumping rate and simulated groundwater TDS concentrations. Because actual pumping rates were assigned as simulated values, the total simulated PVU pumping for the 33-year calibration is within 0.5 percent of the observed values. However, simulated concentrations and thus mass flux of TDS withdrawn by the PVU pumping wells were consistently about 26 percent less than observed values for all the simulated time periods (33-year simulation, pre-PVU, and post-PVU). The representation of brine inflow was explored through additional modeling to evaluate the effect of the simulated brine source on groundwater TDS concentrations. Results indicated that a saturated-salt constant-flux brine source best replicated the magnitude and transient pattern observed for TDS mass flux from PVU pumping wells. The simulated TDS mass flux to the Dolores River is compared to estimates based on observed streamflow and specific conductance (SC) data for the downstream streamgage. The calibrated model provided a close fit of simulated to measured streamflow at the downstream streamgage, and the calibrated model fit to estimated TDS concentrations at the downstream streamgage was reasonable. The greatest differences between simulated and estimated values occurred during drought periods from June 2000 to March 2003, May 2012 to June 2013, and October 2013 to October 2014, when simulated TDS concentrations in the river were greater than estimated concentrations. In general, simulated TDS mass flux to the river for the pre-PVU period is in good agreement with estimated values (2-percent difference), but the model overestimated TDS mass flux to the river by about 41 percent during the post-PVU period. The model uncertainty with respect to TDS mass flux to the river indicates other processes or model parameters not well represented by the model are affecting the system, especially during drought. During model calibration, the most sensitive parameters were identified as vertical hydraulic conductivity of the alluvial aquifer, conductance of the Dolores River streambed, ET extinction depth and rate, and recharge rate. Five 5-year scenarios of conditions for 2021–25 were simulated to assist evaluation of alternative strategies to manage the discharge of brine into the Dolores River. The first scenario simulates no PVU pumping and serves as a base case for comparison to the other scenarios. Two scenarios simulate the effects of varying withdrawal timing at an annual rate about one-third less than during 2010 through 2018. During high-flow spring snowmelt runoff periods when brine discharge is naturally minimized, PVU pumping does not substantially affect salinity in the Dolores River, and comparison of these two scenarios indicates that scheduling brine withdrawals during times of low river stage is nearly as effective at reducing TDS mass flux to the river as pumping brine year-round. Cessation of pumping during periods of high river stage may be advantageous for system maintenance, brine injection, and seismic-risk reduction. The fourth scenario tested the effect of reducing irrigation-return flow on brine discharge and predicted a slight reduction of TDS mass flux to the Dolores River, but not as great a reduction as that of using the PVU to remove brine. The fifth scenario simulated 5 years of drought conditions without PVU pumping and indicates brine discharge during drought about 15 percent greater than during average hydrologic conditions. Results from scenario 5 are consistent with the calibrated model results and indicate that aquifer properties and ET processes and parameters may be affecting simulation results during drought. The Paradox Valley groundwater model provides a reasonable overall match to observed conditions in the Dolores River. The model is useful for evaluating relative differences between brine management scenarios to inform PVU operational decisions and to identify gaps in data and process understanding. Representation of the brine source, hydraulic-conductivity parameters, and recharge and ET processes were identified as potential areas for additional field and modeling research. Additional research in the Paradox Valley might include field-data collection that provides additional information on the hydrogeologic framework, groundwater levels, groundwater TDS concentrations, stream characteristics, and aquifer properties. Additional modeling efforts could benefit from applying advanced tools for model development, calibration, and visualization including parameter-estimation and sensitivity analysis. Statistical evaluation of known model uncertainties such as hydraulic conductivity, streambed conductance, representations of the brine source, recharge, and ET could improve the match between simulated and estimated TDS mass flux from PVU pumping wells and to the Dolores River further informing model predictions and system understanding for the Paradox Valley.

Colorado↗
USGS2026

Treatability study to evaluate bioremediation of trichloroethene at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, 2020–22

Executive Summary Chlorinated solvents, including trichloroethene (TCE) and other chlorinated volatile organic compounds (cVOCs), are widespread contaminants that can be treated by bioremediation approaches that enhance anaerobic reductive dechlorination. Reductive dechlorination can be enhanced either through the addition of an electron donor (biostimulation) or the addition of a known dechlorinating culture (bioaugmentation) along with an electron donor. Although bioremediation has been applied at many TCE-contaminated groundwater sites, application in source zones at sites where residual dense nonaqueous phase liquid (DNAPL) is present is more limited. In this study, laboratory and field treatability tests were completed to evaluate the potential application of anaerobic bioremediation for a shallow groundwater plume containing TCE in a perched alluvial aquifer at Site K, former Twin Cities Army Ammunition Plant, Arden Hills, Minnesota, which was on the National Priorities List as the New Brighton/Arden Hills Superfund site until 2019. In addition to the presence of residual DNAPL at the site, temporal variability in groundwater flow directions and input of oxygenated recharge were possible complicating factors for the application of enhanced anaerobic biodegradation in the shallow plume. The Site K plume extends beneath the footprint of Building 103, which was demolished in 2006, and soil excavations to a maximum depth of 6 feet (ft) below ground surface in 2014 were known to leave some deeper contaminated soil in place in the TCE source area. Groundwater treatment at the site, formalized as part of the 1997 Record of Decision, has been in operation since 1986 and consists of an extraction trench at the downgradient edge of the plume to collect groundwater, which is then pumped to an on-site air stripper. Groundwater concentrations in the plume have been relatively stable since treatment began, indicating a continued source of TCE in the aquifer. The desire for a destructive remedy that would enhance the removal of cVOCs in the aquifer at Site K and shorten the remediation timeframe led the U.S. Army to request that the U.S. Geological Survey conduct a groundwater treatability study to assess bioremediation. This report describes the U.S. Geological Survey bioremediation treatability study conducted during 2020–22, including pre-design site characterization to assist in formulating the bioremediation approach, laboratory experiments to support the design of the field pilot test, and implementation and 1-year performance monitoring results for the pilot test. Pre-design site characterization included the collection of soil cores for cVOC analysis and lithologic descriptions and the re-installment of three wells to obtain hydrologic measurements and initial groundwater chemistry. Relatively flat head gradients were measured at the site, and substantial decreases in water-level elevations occurred from spring to summer (May–July 2021). Continuous water-level monitoring indicated a rapid response to precipitation. Groundwater flow velocities were consistently less than 0.5 foot per day, and the pilot bioremediation test was therefore designed with short lateral distances (about 5 ft) between injection and individual monitoring points. Soil analyses confirmed that high volatile organic compound contamination was left in place in the source area. The highest concentrations were near or in clay at the base of the perched aquifer. Concentrations of cVOCs measured in the replaced wells were consistent with historical data and had a maximum TCE concentration of 57,700 micrograms per liter (μg/L), indicative of nearby residual DNAPL based on the general rule of observed concentrations exceeding 1 percent of solubility. The primary TCE daughter product detected was 1,2-cis-dichloroethene (cisDCE), which indicated limited reductive dechlorination in the plume. Groundwater in both the source and downgradient areas was relatively reducing during the pre-design characterization, particularly in the source area where methane concentrations greater than 400 μg/L were measured. Initial laboratory tests conducted using native aquifer microorganisms from the three replacement wells showed that anaerobic TCE biodegradation rates were low when biostimulated with the addition of sodium lactate as an electron donor, also known as a carbon donor, and resulted in the production of only cisDCE. Addition of a known dechlorinating culture, WBC-2, however, resulted in rapid biodegradation and production of ethene, verifying complete reductive dechlorination of TCE. Microcosms constructed with aquifer soil collected from the site were used to evaluate other electron donors besides lactate to support reductive dechlorination by WBC-2, including corn syrup as an alternative fast-release compound and whey, soy-based vegetable oil, and 3-D Microemulsion (Regenesis, San Clemente, California) as slow-release compounds. First-order rate constants for total organic chlorine removal in these WBC-2 amended microcosms were greatest with either lactate or vegetable oil as the donor, ranging between 0.061 and 0.047 per day or corresponding half-lives of 11–15 days. Testing of commercial products in other WBC-2-bioaugmented microcosms led to selection for the field pilot test of an emulsified vegetable oil product that also contained some sodium lactate as a fast-release donor. Delaying the addition of WBC-2 relative to the donor in the microcosms resulted in the most rapid overall biodegradation rates. The selected design for the pilot test utilized three separate test plots, each about 30-ft wide and 60-ft long: plots GS1 and GS2 in the source area of the plume and plot GS3 in the downgradient area of the plume near the excavation trench. Each test plot had one injection well, one monitoring well upgradient from the injection point, and 12 surrounding monitoring wells in a grid to capture variable groundwater flow directions. Donor injections, which included a bromide tracer, were completed in October 2021, immediately following baseline sampling, and the WBC-2 culture was injected about 40 days later, between November 30 and December 2, 2021. Performance monitoring conducted until December 2022 included hydrologic measurements and analyses of cVOCs, redox-sensitive constituents, dissolved organic carbon, bromide, volatile fatty acids, compound-specific carbon isotopes, and microbial communities. The biogeochemical data collected during the pilot tests in the three treatment plots showed that enhanced, complete reductive dechlorination of cVOCs in the groundwater was achieved in the GS1 and GS3 plots. In contrast, evidence of distribution of the injected amendments and subsequent biodegradation was limited in GS2, which was in an area of more heterogeneous soil lithology and low water table elevations. The molar composition of volatile organic compounds in the GS1 and GS3 plots was dominated by ethene in wells that were reached by the injected amendments by the end of the monitoring period. In the GS1 and GS3 plots, similar patterns were observed of cVOC concentrations decreasing to near detection levels, or below, at some wells sampled in July and October 2022, whereas ethene became dominant and indicated sustained complete reductive dechlorination. Baseline cVOC concentrations were more than a factor of 10 higher in the groundwater in the GS1 plot than in GS3, but no apparent inhibition of complete dechlorination occurred. As expected from the initial pre-design site data and the laboratory experiments, enhanced dissolution of residual DNAPL coupled to biodegradation was evident in the GS1 plot, where a marked increase in dichloroethene (DCE) above the initial baseline and upgradient TCE and DCE concentrations occurred. DCE concentrations subsequently declined where DNAPL dissolution was evident, concurrent with production of vinyl chloride and then predominantly ethene. Thus, overall biodegradation rates outpaced the DNAPL dissolution and desorption and DCE production in the source area. This success in complete degradation to predominantly ethene was achieved even in areas where the DCE concentrations reached a maximum of about 30,000 μg/L. Compound specific isotope analysis of carbon in TCE, cisDCE, trans-1,2-dichloroethene, and vinyl chloride was conducted to provide another line of evidence of the occurrence and extent of anaerobic biodegradation. Along a flow path in each plot that was affected by the injected amendments, carbon isotopes in the TCE and daughter cVOCs in the groundwater became isotopically heavier, indicating biodegradation. Enhanced biodegradation rates calculated from the field tests in GS1 and GS3 showed half-lives of 36.9–75.3 days for DCE degradation and 9.48–38.5 days for ethene production. Notably, these ethene production rates calculated from the field tests are consistent with the results of WBC-2-bioaugmented microcosms amended with either lactate or vegetable oil, which had half-lives for total organic chlorine removal that ranged from 11 to 15 days. These rates indicated rapid enhanced biodegradation, which is promising for application of a full-scale bioremediation remedy. Ultimately, however, the mass of residual or sorbed TCE in the aquifer that remains accessible for dissolution and biodegradation would likely control the time required for a full-scale bioremediation effort to achieve performance goals for TCE and cisDCE specified in the Record of Decision for Site K. The field pilot tests showed that the relatively low hydraulic head gradients and temporal changes in groundwater flow directions in the shallow aquifer would add complexity to a full-scale bioremediation effort. The radius of influence (ROI) at GS1 and GS3 (16.3 ft and 12.7 ft, respectively) were close to the design ROI of 15 ft. The estimated ROI at GS2 was about four times the design ROI, but may be less reliable at this location owing to groundwater flow direction. In addition, the low temperatures following WBC-2 injection in late November to early December 2021, in combination with the low hydraulic head gradients, were probably major factors in the delay observed before the onset of enhanced biodegradation following injection of the culture. Additional test injections could be beneficial to optimize the timing of donor and culture injections with the variable temperatures and hydraulic head in the shallow aquifer.

Minnesota↗
USGS2026

Capitalization of positional (Lower/Middle/Upper) and temporal (Early/Middle/Late) adjectives in the names of formal chronostratigraphic and geochronologic units of the Phanerozoic

Many authors are understandably confused about the capitalization of the words “lower,” “middle,” “upper,” “early,” and “late.” Where these words are used simply as descriptive adjectives, they should be in lowercase; where they form the first word of a formal chronostratigraphic or geochronologic unit name, they should be in uppercase.

Professional Paper↗
USGS1999

The effects of the Chesapeake Bay impact crater on the geological framework and correlation of hydrogeologic units of the lower York-James Peninsula, Virginia

This report documents the highly variable structure, stratigraphy, and buried topography of the outer rim of the Chesapeake Bay impact crater created by its impact and burial. Lithologies of cores are correlated with borehole geophysical logs to characterize the physical properties of the stratigraphic units and their geophysical signatures. The correlation between cores, well cuttings, and borehole geophysical logs is augmented with seismic-reflection data, and these data are compiled into a lithostratigraphic cross section that illustrates the geological framework of the lower York-James Peninsula and immediate surrounding areas.

Virginia↗
USGS2026

Methodology for construction of a three-layer geologic model of the conterminous United States using land surface, top of bedrock, and top of basement

This report describes the methodology used for the construction of a digital three-layer geologic model of the conterminous United States by mapping the altitude of three surfaces: land surface, the top of bedrock, and the top of basement. These surfaces are mapped through the compilation and synthesis of published stratigraphic horizons from numerous topical studies. The mapped surfaces create a three-layer geologic model with three geomaterial-based subdivisions: unconsolidated to weakly consolidated sediment; layered consolidated rock strata that constitute bedrock; and crystalline rocks that are described as “basement,” consisting of either igneous, metamorphic, or highly deformed rocks. The data compilation and synthesis are highly dependent on the definition of the informal terms “bedrock” and “basement,” which may describe different ages or types of rock in different parts of the conterminous United States. This report presents the conceptualization of the three mapped layers, describes the datasets used, and summarizes the decisions made while compiling the three-layer model from the various sources. This digital dataset was created as part of efforts by the U.S. Geological Survey to develop subsurface geologic data in geospatial form as part of a broad directive to develop two-dimensional and three-dimensional geologic information at detailed, national, and continental scales. This digital dataset partly fulfills the goal of the U.S. Geological Survey’s National Cooperative Geologic Mapping Program to construct a national-scale three-dimensional geologic model.

conterminous United States↗
USGS1998

Satellite imagery of the north-central Gulf of Mexico, June 1993-May 1997

This CD contains imagery collected by the Advanced Very High Resolution Radiometer (AVHRR) on the NOAA polar-orbiting weather satellites. The AVHRR provides almost daily coverage of a site at a resolution of approximately 1 km. The data types included are sea surface temperature (SST), water reflectance (REF), and a false-color infrared overview (FCI).

Alabama, Florida, Louisiana, Mississippi↗
USGS2026

Production of mineral commodities and geospatial map of the mineral industries and related infrastructure of China

As part of the U.S. Geological Survey’s (USGS) mission to distribute global mineral information and analyze supply chains, this study provides a comprehensive review of the global significance of China’s mineral production and capacity in 2023. Of 77 mineral commodities in the USGS dataset, China produced 74 and was the world’s first-ranked producer for 39 of the 74. Compared to the high share of global mineral production, including up to 98 percent of global gallium production, the country’s share of global mineral reserves was relatively small, ranging from 20 percent (zinc ore) to 52 percent (tungsten ore). China’s imports of metal ores, slag, and ash accounted for 64 percent of global imports of such commodities by value. The country’s exports of base metals and articles of base metal accounted for 17 percent of the global exports. To help nongeographic information system users assess the spatial distribution of mineral mines, processing facilities, and ports for trades in China, this study created a geospatial (also called “georeferenced”) portable document format (GeoPDF) map. In addition, the GeoPDF contains mineral resource tracts (such as antimony, copper, potash, coal, and oil and gas), exploration sites, and energy infrastructure based on the preexisting USGS data.

Open-File Report↗
USGS2025

Methodology for compilation of previously published contour data showing the altitude of the base of Dakota Sandstone on the Colorado Plateau, Arizona, Colorado, New Mexico, and Utah

Structure contours and other geologic information from numerous published geologic maps were digitized and compiled into a digital dataset showing the configuration of a single stratigraphic datum, the base of the Dakota Sandstone and its equivalents across the Colorado Plateau. The principal maps compiled in digital form are a series of 1:250,000-scale 1 degree (°) × 2° quadrangle maps published by the U.S. Geological Survey, augmented by other geologic maps published at various map scales. The compiled digital dataset contains geologic map polygons of the Dakota Sandstone and regional stratigraphic equivalents, the location of faults and fold axes, structure contour lines that define the altitude of the base of the unit and bedding orientation data computed from the structure contour lines. This report provides the scientific rationale for compilation of these data and describes the compilation methodology for each of the data elements. This report provides an extended description of the data compilation in a companion U.S. Geological Survey digital data release of spatial data and attributes associated with the contoured surface and associated geologic data layers.

Arizona, Colorado, New Mexico, Utah↗