SEARCH · USGS Science

Results for “Journal of Applied Volcanology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,659 records · Page 19Linked to original sources

USGS2025

Constraining landslide frequency across the United States to inform county-level risk reduction

Informative landslide hazard estimates are needed to support landslide mitigation strategies to reduce landslide risk across the United States. Whereas existing national-scale landslide susceptibility products assess where landslides are likely to occur, they do not address how often , which is a critical element of landslide hazard and risk assessments. In particular, the U.S. Federal Emergency Management Agency's National Risk Index (NRI) requires landslide frequency estimates to inform expected annual loss estimates. We present county-level landslide frequency (landslides per area per year) estimates for the 50 US states. We applied Bayesian negative binomial regression to estimate both the expected (average) reported landslide frequency and full distribution of annual landslide counts for each county. We compared a suite of models that used combinations of landslide-susceptible area, probability of potentially triggering earthquakes, frequency of potentially triggering precipitation, and ecological region as predictors. We trained our models with landslide inventory data from counties with the most comprehensive records available nationwide and used zero-inflated negative binomial distributions as an incompleteness model to correct for temporal reporting gaps. We selected a preferred frequency model to inform the NRI based on information criteria and physically plausible parameter estimates. The model showed that average annual reported landslide frequencies vary by 5 orders of magnitude across US counties, ranging from 0.002 (0.00015–0.05) landslides 1000 km −2 yr −1 in Kusilvak Census Area, Alaska, to 29 (19–46) landslides 1000 km −2 yr −1 in Lake County, California, reflecting the country's strong variations in landslide susceptibility, earthquake probability, and other factors for which ecological region serves as a proxy. Counties with estimated frequencies in the top 20 % of all counties are predominately along the West Coast of the continental United States, in mountainous regions of the Pacific Northwest and Intermountain West, in locally steep or earthquake-prone regions of the Midwest and Southeast, along the Appalachians, in southern and southeastern Alaska, and on some Hawaiian islands. By examining the number of landslides predicted in 99th percentile years for each county, we identified that 26 % of US counties likely have potential for widespread landsliding with more than 10 landslides 1000 km −2 yr −1 , even when such large events have not been reported in the training data for that county. Overall, our results better represent the range of possible landslide frequencies and spatial variations than previous national-scale estimates reported in the NRI, and our approach can inform other risk-reduction and loss-mitigation efforts across the United States and globally.

Natural Hazards and Earth System Sciences↗

USGS2023

The 2023 US 50-State National Seismic Hazard Model: Overview and implications

The US National Seismic Hazard Model (NSHM) was updated in 2023 for all 50 states using new science on seismicity, fault ruptures, ground motions, and probabilistic techniques to produce a standard of practice for public policy and other engineering applications (defined for return periods greater than ∼475 or less than ∼10,000 years). Changes in 2023 time-independent seismic hazard (both increases and decreases compared to previous NSHMs) are substantial because the new model considers more data and updated earthquake rupture forecasts and ground-motion components. In developing the 2023 model, we tried to apply best available or applicable science based on advice of co-authors, more than 50 reviewers, and hundreds of hazard scientists and end-users, who attended public workshops and provided technical inputs. The hazard assessment incorporates new catalogs, declustering algorithms, gridded seismicity models, magnitude-scaling equations, fault-based structural and deformation models, multi-fault earthquake rupture forecast models, semi-empirical and simulation-based ground-motion models, and site amplification models conditioned on shear-wave velocities of the upper 30 m of soil and deeper sedimentary basin structures. Seismic hazard calculations yield hazard curves at hundreds of thousands of sites, ground-motion maps, uniform-hazard response spectra, and disaggregations developed for pseudo-spectral accelerations at 21 oscillator periods and two peak parameters, Modified Mercalli Intensity, and 8 site classes required by building codes and other public policy applications. Tests show the new model is consistent with past ShakeMap intensity observations. Sensitivity and uncertainty assessments ensure resulting ground motions are compatible with known hazard information and highlight the range and causes of variability in ground motions. We produce several impact products including building seismic design criteria, intensity maps, planning scenarios, and engineering risk assessments showing the potential physical and social impacts. These applications provide a basis for assessing, planning, and mitigating the effects of future earthquakes.

Earthquake Spectra↗

USGS2024

The spatially adaptable filter for error reduction (SAFER) process: Remote sensing-based LANDFIRE disturbance mapping updates

LANDFIRE (LF) has been producing periodic spatially explicit vegetation change maps (i.e., LF disturbance products) across the entire United States since 1999 at a 30 m spatial resolution. These disturbance products include data products produced by various fire programs, field-mapped vegetation and fuel treatment activity (i.e., events) submissions from various agencies, and disturbances detected by the U.S. Geological Survey Earth Resources Observation and Science (EROS)-based Remote Sensing of Landscape Change (RSLC) process. The RSLC process applies a bi-temporal change detection algorithm to Landsat satellite-based seasonal composites to generate the interim disturbances that are subsequently reviewed by analysts to reduce omission and commission errors before ingestion them into LF’s disturbance products. The latency of the disturbance product is contingent on timely data availability and analyst review. This work describes the development and integration of the Spatially Adaptable Filter for Error Reduction (SAFER) process and other error and latency reduction improvements to the RSLC process. SAFER is a random forest-based supervised classifier and uses predictor variables that are derived from multiple years of pre- and post-disturbance Landsat band observations. Predictor variables include reflectance, indices, and spatial contextual information. Spatial contextual information that is unique to each contiguous disturbance region is parameterized as Z scores using differential observations of the disturbed regions with its undisturbed neighbors. The SAFER process was prototyped for inclusion in the RSLC process over five regions within the conterminous United States (CONUS) and regional model performance, evaluated using 2016 data. Results show that the inclusion of the SAFER process increased the accuracies of the interim disturbance detections and thus has potential to reduce the time needed for analyst review. LF does not track the time taken by each analyst for each tile, and hence, the relative effort saved was parameterized as the percentage of 30 m pixels that are correctly classified in the SAFER outputs to the total number of pixels that are incorrectly classified in the interim disturbance and are presented. The SAFER prototype outputs showed that the relative analysts’ effort saved could be over 95%. The regional model performance evaluation showed that SAFER’s performance depended on the nature of disturbances and availability of cloud-free images relative to the time of disturbances. The accuracy estimates for CONUS were inferred by comparing the 2017 SAFER outputs to the 2017 analyst-reviewed data. As expected, the SAFER outputs had higher accuracies compared to the interim disturbances, and CONUS-wide relative effort saved was over 92%. The regional variation in the accuracies and effort saved are discussed in relation to the vegetation and disturbance type in each region. SAFER is now operationally integrated into the RSLC process, and LANDFIRE is well poised for annual updates, contingent on the availability of data.

Fire↗

USGS1993

Ground-water quality near an inactive landfill and sludge-spreading area, Tallahassee, Florida

Ground-water quality of a 120-acre area encompassing an inactive landfill southwest of Tallahassee, Florida, was assessed by installing and sampling 21 monitoring wells. Sludge from a municipal sewage-treatment plant was also applied to the land surface near the landfill site. Water samples were collected from the 21 monitoring wells from June 1987 through September 1990 and analyzed for concentrations of major ions, nitrogen species, trace metals, field measurements, and more than 140 organic constituents. Water quality in the Upper Floridan aquifer at the study site was compared to background water quality in other areas of Leon County. Ground-water quality of the study site was evaluated by the location of wells sampled in relation to the landfill and the sludge-spreading areas. Results of nonparametric statistical analysis indicated that potassium and nitrite plus nitrate as nitrogen concentrations in water samples from wells completed in the Upper Floridan aquifer at the study site were significantly different at the 5 percent probability level from those in samples from background wells completed in this aquifer in Leon County. Median potassium concentrations were 0.4 mg/L (milligrams per liter) in water from wells at the study site and 0.7 mg/L in water from background wells in Leon County. Median nitrite plus nitrate concentrations were 6.48 mg/L in water samples from wells at the study site and 0.51 mg/L in water samples from background wells. Graphical comparison of the water quality characteristics in water from six categories of wells; upgradient, landfill, adjacent to the landfill, downgradient onsite, downgradient offsite, and background Leon County, indicated that sodium, bicarbonate, sulfate, iron, manganese, and dissolved solids concentrations and specific conductance values were highest within the landfill. Upgradient and downgradient well categories include wells in areas affected by sludge spreading. Localized reducing conditions were indicated in a downgradient area by median iron concentrations of 930 and 30 ug/L (micrograms per liter) in samples from wells only 5 feet apart. Nitrite plus nitrate concentrations were lowest in water from wells in the landfill compared to water from the other categories. Concentrations of most trace elements and organic compounds were mostly below detection limits, although State maximum contaminant levels of 1 ug/L for benzene and vinyl chloride and 3 ug/L for tetrachloroethene were exceeded in 14 samples. Concentrations of sodium, potassium, chloride, sulfate, nitrite plus nitrate, total organic and ammonia nitrogen, and ammonia nitrogen in ground water were statistically analyzed in areas affected by sludge-spreading and other areas. Only nitrite plus nitrate and chloride concentrations were significantly different between the two areas. Median nitrite plus nitrate and chloride concentrations in sludge-spreading areas were 6.9 mg/L and 2.9 mg/L, respectively, compared to 1.1 mg/L and 1.8 mg/L in other areas.

Florida↗

USGS2026

Groundwater-level elevations in the bedrock aquifers of the Denver Basin aquifer system, Elbert County, Colorado, 2015–23

Water users in Elbert County, Colorado, rely on groundwater from bedrock aquifers in the Denver Basin aquifer system (upper Dawson, lower Dawson, Denver, Arapahoe, and Laramie-Fox Hills aquifers) for approximately half of their water uses. Withdrawals from the bedrocks aquifers have increased to meet the water use needs of expanding regional population growth and development. The U.S. Geological Survey, in cooperation with the Elbert County Board of County Commissioners, began a study in 2015 to monitor groundwater levels within Elbert County. The primary purpose of this report is to present a summary of groundwater levels measured during the study period (2015–23) and present results from statistical analyses of changes in groundwater-level elevations through time. Discrete groundwater levels were measured at 36 wells within Elbert County. Seven of those wells contained equipment to make and record continuous groundwater-level measurements at hourly intervals. All aquifers, except the lower Dawson aquifer, had only declining groundwater-level elevations in discrete measurements for wells with statistically significant trends. Of the eight statistically significant trends in the lower Dawson aquifer, two wells indicated increasing groundwater-level elevation from discrete measurements. The groundwater-level elevation trend medians in the upper Dawson, lower Dawson, Denver, Arapahoe, and Laramie-Fox Hills aquifers were −0.23, −0.66, −0.64, −0.39, and −0.63 feet per year, respectively, for discrete groundwater-level elevation measurements. Trends in continuous groundwater-level elevations were in agreement with statistically significant trends in discrete groundwater-level elevations for all wells. The groundwater-level elevation trend medians in this study, compared to the overall trends in a 2015−2018 study, both indicated declining groundwater-level elevations except in the upper Dawson aquifer, where the trend direction was opposite, a positive trend from 2015 to 2018 and a negative trend (declining groundwater elevations) from 2015 to 2023. The change in trends within the upper Dawson aquifer may be affected by differences in the study period and the trend analysis applied. Trends during the 2015–23 study period were compared to departures from the median 2015 groundwater-level elevation for each site in each aquifer. In general, the departures from the 2015 median supported trends observed at each site and correlated spatially with greater departures near the western border of Elbert County. Additionally, 30-year precipitation data showing wet and dry periods were overlaid with the departure from the 2015 median to assess groundwater-level patterns in wells in the five aquifers. Departures from the 2015 median groundwater-level elevations appeared greatest during the dry period between 2020 and 2023. Potentiometric-surface maps of the upper and lower Dawson aquifers created from static April 2023 groundwater elevations indicated groundwater-flow direction is generally from the south to the north. Results of this study could be used to guide additional groundwater monitoring in Elbert County and could aid in long-term planning of water resources.

Colorado↗

USGS1999

Environmental setting and water-quality issues in the lower Tennessee River basin

The goals of the National Water-Quality Assessment Program are to describe current water-quality conditions for a large part of the Nation's water resources, identify water-quality changes over time, and identify the primary natural and human factors that affect water quality. The lower Tennessee River Basin is one of 59 river basins selected for study. The water-quality assessment of the lower Tennessee River Basin study unit began in 1997. The lower Tennessee River Basin study unit encompasses an area of about 19,500 square miles and extends from Chattanooga, Tennessee, to Paducah, Kentucky. The study unit had a population of about 1.5 million people in 1995. The study unit was subdivided into subunits with relatively homogeneous geology and physiography. Subdivision of the study unit creates a framework to assess the effects of natural and cultural settings on water quality. Nine subunits were delineated in the study unit; their boundaries generally coincide with level III and level IV ecoregion boundaries. The nine subunits are the Coastal Plain, Transition, Western Highland Rim, Outer Nashville Basin, Inner Nashville Basin, Eastern Highland Rim, Plateau Escarpment and Valleys, Cumberland Plateau, and Valley and Ridge.The lower Tennessee River Basin consists of predominantly forest (51 percent) and agricultural land (40 percent). Activities related to agricultural land use, therefore, are the primary cultural factors likely to have a widespread effect on surface- and ground-water quality in the study unit. Inputs of total nitrogen and phosphorus from agricultural activities in 1992 were about 161,000 and 37,900 tons, respectively. About 3.7 million pounds (active ingredient) of pesticides was applied to crops in the lower Tennessee River Basin in 1992. State water-quality agencies identified nutrient enrichment and pathogens as water-quality issues affecting both surface and ground water in the lower Tennessee River Basin. Water-quality data collected by State and Federal agencies between 1980 and 1996 were summarized to characterize surface- and ground-water quality of the subunits with respect to these issues. Median concentrations of nitrogen species generally were less than 1 milligram per liter in surface and ground water in all subunits, and were highest throughout the subunits that had the largest percentages of agricultural land use. Median phosphorus concentrations also were less than 1 milligram per liter in all subunits. Phosphatic limestones present in two subunits had a larger effect on phosphorus concentrations in surface and ground water than did the amount of agricultural land use in these subunits. Median counts of fecal coliform were higher in surface water than in ground water in all subunits. The highest median counts in surface water were in the Valley and Ridge (7,500 colonies per 100 milliliters) and the Outer Nashville Basin subunits (5,000 colonies per 100 milliliters). Highest median counts in ground water were in the Inner and Outer Nashville Basin subunit. Natural setting likely has an important effect with respect to fecal contamination of surface and ground water in the lower Tennessee River Basin.

Alabama, Georgia, Kentucky, Mississippi, Tennessee↗

USGS1990

Recharge rates and aquifer hydraulic characteristics for selected drainage basins in middle and east Tennessee

Quantitative information concerning aquifer hydrologic and hydraulic characteristics is needed to manage the development of ground-water resources. These characteristics are poorly defined for the bedrock aquifers in Middle and East Tennessee where demand for water is increasing. This report presents estimates of recharge rate, storage coefficient, diffusivity, and transmissivity for representative drainage basins in Middle and East Tennessee, as determined from analyses of stream-aquifer interactions. The drainage basins have been grouped according to the underlying major aquifer, then statistical descriptions applied to each group, in order to define area1 distribution of these characteristics. Aquifer recharge rates are estimated for representative low, average, and high flow years for 63 drainage basins using hydrograph analysis techniques. Net annual recharge during average flow years for all basins ranges from 4.1 to 16.8 in/yr (inches per year), with a mean value of 7.3 in. In general, recharge rates are highest for basins underlain by the Blue Ridge aquifer (mean value11.7 in/yr) and lowest for basins underlain by the Central Basin aquifer (mean value 5.6 in/yr). Mean recharge values for the Cumberland Plateau, Highland Rim, and Valley and Ridge aquifers are 6.5, 7.4, and 6.6 in/yr, respectively. Gravity drainage characterizes ground-water flow in most surficial bedrock aquifer in Tennessee. Accordingly, a gravity yield analysis, which compares concurrent water-level and streamflow hydrographs, was used to estimate aquifer storage coefficient for nine study basins. The basin estimates range from 0.002 to 0.140; however, most estimates are within a narrow range of values, from 0.01 to 0.025. Accordingly, storage coefficient is estimated to be 0.01 for all aquifers in Middle and East Tennessee, with the exception of the aquifer in the inner part of the Central Basin, for which storage coefficient is estimated to be 0.002. Estimates of aquifer hydraulic diffusivity are derived from estimates of the streamflow recession index and drainage density for 75 drainage basins; values range from 3,300 to 130,000 ft^2/d (feet squared per day). Basin-specific and site-specific estimates of transmissivity are computed from estimates of hydraulic diffusivity and specific-capacity test data, respectively. Basin-specific, or areal, estimates of transmissivity range from 22 to 1,300 ft^2/d, with a mean of 240 ft^2/d In general, areal transmissivity is highest for basins underlain by the Cumberland Plateau aquifer (mean value 480 ft^2/d) and lowest for basins underlain by the Central Basin aquifer (mean value 79 ft^2/d). Mean transmissivity values for the Highland Rim, Valley and Ridge, and Blue Ridge aquifer are 320,140, and 120 ft^2/d respectively. Site-specific estimates of transmissivity, computed from specific-capacity data from 118 test wells in Middle and East Tennessee range from 2 to 93,000 ft^2/d with a mean of 2,600 ft^2/d Mean transmissivity values for the Cumberland Plateau, Highland Rim, Central Basin, Valley and Ridge, and Blue Ridge aquifers are 2,800,1,200, 7,800, 390, and 65Oft Id, respectively.

Tennessee↗

USGS1998

Ground-water flow in the surficial aquifer system and potential movement of contaminants from selected waste-disposal sites at Naval Station Mayport, Florida

Ground-water flow through the surficial aquifer system at Naval Station Mayport near Jacksonville, Florida, was simulated with a two-layer finite-difference model as part of an investigation conducted by the U.S. Geological Survey. The model was calibrated to 229 water-level measurements from 181 wells during three synoptic surveys (July 17, 1995; July 31, 1996; and October 24, 1996). A quantifiable understanding of ground-water flow through the surficial aquifer was needed to evaluate remedial-action alternatives under consideration by the Naval Station Mayport to control the possible movement of contaminants from sites on the station. Multi-well aquifer tests, single-well tests, and slug tests were conducted to estimate the hydraulic properties of the surficial aquifer system, which was divided into three geohydrologic unitsï¿½an S-zone and an I-zone separated by a marsh-muck confining unit. The recharge rate was estimated to range from 4 to 15 inches per year (95 percent confidence limits), based on a chloride-ratio method. Most of the simulations following model calibration were based on a recharge rate of 8 inches per year to unirrigated pervious areas. The advective displacement of saline pore water during the last 200 years was simulated using a particle-tracking routine, MODPATH, applied to calibrated steady-state and transient models of the Mayport peninsula. The surficial aquifer system at Naval Station Mayport has been modified greatly by natural and anthropogenic forces so that the freshwater flow system is expanding and saltwater is being flushed from the system. A new MODFLOW package (VAR1) was written to simulate the temporal variation of hydraulic properties caused by construction activities at Naval Station Mayport. The transiently simulated saltwater distribution after 200 years of displacement described the chloride distribution in the I-zone (determined from measurements made during 1993 and 1996) better than the steady-state simulation. The advective movement of contaminants from selected sites within the solid waste management units to discharge points was simulated using MODPATH. Most of the particles were discharged to the nearest surface-water feature after traveling less than 1,000 feet in the ground-water system. Most areas within 1,000 feet of a surface-water feature or storm sewer had traveltimes of less than 50 years, based on an effective porosity of 40 percent. Contributing areas, traveltimes, and pathlines were identified for 224 wells at Naval Station Mayport under steady-state and transient conditions by back-tracking a particle from the midpoint of the wetted screen of each well. Traveltimes to contributing areas that ranged between 15 and 50 years, estimated by the steady-state model, differed most from the transient traveltime estimates. Estimates of traveltimes and pathlines based on steady-state model results typically were 10 to 20 years more and about twice as long as corresponding estimates from the transient model. The models differed because the steady-state model simulated 1996 conditions when Naval Station Mayport had more impervious surfaces than at any earlier time. The expansion of the impervious surfaces increased the average distance between contributing areas and observation wells.

Florida↗

USGS2024

Introduction and methods of analysis for peak streamflow trends and their relation to changes in climate in Illinois, Iowa, Michigan, Minnesota, Missouri, Montana, North Dakota, South Dakota, and Wisconsin

Flood-frequency analysis, also called peak-flow frequency or flood-flow frequency analysis, is essential to water resources management applications including critical structure design and floodplain mapping. Federal guidelines for doing flood-frequency analyses are presented in a U.S. Geological Survey Techniques and Methods Report known as Bulletin 17C. A basic assumption within Bulletin 17C is that for drainage basins without major hydrologic alterations, statistical properties of the distribution of annual peak streamflows (peak flows) are stationary; that is, the mean, variance, and skew are constant. The stationarity assumption has been widely accepted within the flood-frequency community; however, a better understanding of long-term climatic persistence and concerns about potential climate change and land-use change has caused a reexamination of the stationarity assumption. Flood-frequency analyses that do not incorporate observed trends and abrupt changes may result in a poor representation of the true flood risk. Bulletin 17C does not offer guidance for incorporating nonstationarities when estimating floods, and it describes a need for studies that incorporate changing climate or basin characteristics. In response to this need and a history of concern regarding nonstationarity peak flows in the region, this study was done by the U.S. Geological Survey, in cooperation with the Departments of Transportation of Illinois, Iowa, Michigan, Minnesota, Missouri, South Dakota, and Wisconsin; the Montana Department of Natural Resources and Conservation; and the North Dakota Department of Water Resources, to assess potential nonstationarity in peak flows in the north-central United States. This chapter summarizes the methods used to detect hydroclimatic changes in peak-flow data in the study region. A wide range of analyses and statistical approaches are applied to document the primary mechanisms controlling floods and characterize temporal changes in hydroclimatic variables and peak flow. Four periods were selected for analysis of peak flow, daily streamflow, and climate data. The periods are (1) a 100-year period, 1921–2020; (2) a 75-year period, 1946–2020; (3) a 50-year period, 1971–2020; and (4) a 30-year period, 1991–2020. The climate data consist of monthly time series estimates of temperature, precipitation, potential evapotranspiration, actual evapotranspiration, snowfall, soil moisture storage, snow water equivalent, and runoff on a 3.1-mile by 3.1-mile grid for the conterminous United States. Statistical and graphical analyses were used to investigate potential changes in hydrology and climate. The starting point for these analyses was the initial data analysis of peak flow described in Bulletin 17C, which includes plotting the peak flow and checking for autocorrelation, monotonic trends, and changes points. Analyses were added to examine additional features in the data. To examine potential causal drivers of changes, the climate data were analyzed graphically and statistically. Results are provided in a U.S. Geological Survey data release. The study limitations are documented for users of the results.

Iowa, Illinois, Michigan, Missouri, Minnesota, Mon↗

USGS2025

Refining the earthquake history of south-central Alaska through lake records

The Alaska–Aleutian subduction zone (AASZ) is one of the world's most seismically active plate boundaries and the source of the 1964 M w 9.2 Great Alaska earthquake–the second largest instrumentally recorded earthquake in the world. Understanding the nature and frequency of such earthquakes is necessary for seismic and tsunami hazard assessment, but instrumental and historical records that span less than 150 years are too short to allow a statistically reliable analysis of earthquake recurrence times. This calls for studies of evidence of past earthquakes, extending the earthquake catalog further back in time. Subduction-zone paleoseismology in south-central Alaska is predominantly based on coastal evidence of land-level changes and tsunamis generated by megathrust earthquakes and preserved in the geological record. A complementary approach is lacustrine paleoseismology, which is still a relatively young discipline in Alaska. However, globally, lake basins are well-established high-resolution and continuous recorders of paleoseismic activity along subduction zones, relying on the identification of underwater landslide deposits and turbidites generated by seismic shaking. As a result, lake basins not only register ground shaking from megathrust earthquakes, but also from intraslab and crustal earthquakes, which are typically not accompanied by significant land-level changes. In this review paper, we combine coastal and lacustrine paleoseismology approaches to refine the south-central Alaskan earthquake history by comparing the paleoseismic records from two lakes (i.e., Eklutna Lake, located in the Chugach Mountain Range, and Skilak Lake, situated on the Kenai Peninsula) with the coastal and crustal earthquake catalog in Alaska. The resulting age ranges of all known megathrust earthquakes involving the Alaskan megathrust between the Kodiak and Prince William Sound (PWS) sections are more precise and accurate for the last 1.3 kyrs BP than the previously published age ranges from coastal records. As a result, this study supports the following key conclusions: (1) The 1964 CE earthquake was an exceptionally strong and unique event in the last 2000 years, rupturing the PWS, Kenai, Barren Islands, and Kodiak sections simultaneously. (2) The high-resolution and seasonal markings of the varved lake records now disentangle for the first time closely timed earthquakes, which was not possible based on the coastal evidence alone. (3) No persistent megathrust rupture boundaries exist. So, the possibility of a full rupture of the entire eastern AASZ, from PWS to Semidi cannot be excluded. (4) The rupture pattern in the eastern AASZ reveals superimposed cycles of multi-asperity ruptures (1964 earthquake) and clustered complementary partial ruptures, or rupture cascades. (5) The PWS section hosts the largest asperity in the eastern AASZ. (6) The shaking record of megathrust earthquakes indicates a time-dependent (quasiperiodic) behavior for the study area, but the observation of complementary clusters means that the hazards will not drop to zero but instead may even increase for a neighboring section. (7) The time-independent behavior of intraplate earthquakes implies that the intraslab hazard did not decrease following the 2016 and 2018 earthquakes. This study utilizes an integrated approach for subduction zone paleoseismology as a solution for unraveling recurrence and rupture patterns in Alaska, which can be applied worldwide.

Alaska↗

USGS1999

Comparison of two approaches for determining ground-water discharge and pumpage in the lower Arkansas River Basin, Colorado, 1997-98

In March 1994, the Colorado Division of Water Resources (CDWR) adopted “Rules Governing the Measurement of Tributary Ground Water Diversions Located in the Arkansas River Basin” (Office of the State Engineer, 1994); these initial rules were amended in February 1996 (Office of the State Engineer, 1996). The amended rules require users of wells that divert tributary ground water to annually report the water pumped monthly by each well. The rules allow a well owner to report the pumpage measured by a totalizing flowmeter (TFM) or pumpage determined from electrical power data and a power conversion coefficient (PCC) (Hurr and Litke, 1989). Opinions by representatives of the State of Kansas, presented before the Special Master hearing a court case [State of Kansas v. State of Colorado, No. 105 Original (1996)] concerning post-Compact well pumping, stated that the PCC approach does not provide the same level of accuracy and reliability as a TFM when used to determine pumpage. In 1997, the U.S. Geological Survey (USGS), in cooperation with the CDWR, began a 2-year study to compare ground-water pumpage estimates made using the TFM and the PCC approaches. The study area was along the Arkansas River between Pueblo, Colorado, and the Colorado-Kansas State line (fig. 1). The two approaches for estimating ground-water discharge and pumpage were compared for more than 100 wells completed in the alluvial aquifer of the Arkansas River Basin. The TFM approach uses an inline flowmeter to directly measure instantaneous discharge and the total volume of water pumped at a well. The PCC approach uses electrical power consumption records and a power conversion coefficient to estimate the pumpage at ground-water wells. This executive summary describes the results of the comparison of the two approaches. Specifically, (1) the differences in instantaneous discharge measured with three portable flowmeters and measured with an inline TFM are evaluated, and the statistical differences in paired instantaneous discharge between the two approaches are determined; (2) short- and long-term variations in the PCC’s are presented; (3) differences in pumpage between the two approaches are evaluated, and the statistical differences in pumpage between the two approaches are determined; (4) potential sources of discrepancy between pumpage estimates are discussed; and (5) differences in total network pumpage using the two approaches are presented. During the irrigation seasons of 1997 and 1998, instantaneous discharge and electrical power demand were measured at randomly selected wells to determine PCC’s. At more than 100 wells, the PCC’s determined during the 1998 season were applied to total electrical power consumption data that was recorded between the initial and final readings at each network well site in 1998 to estimate total ground-water pumpage. At each site, an inline TFM was installed in a full-flowing, acceptable test section of pipe on the discharge side of the pump where the measurement of discharge was made. Measurements of instantaneous ground-water discharge also were made using three different types of portable flowmeters. The average velocity multiplied by the cross-sectional area of the discharge pipe was used to compute the discharge in gallons per minute. Whenever possible, discharge measurements were made at each network site using all three types of portable flowmeters.

Colorado↗

USGS2024

Timing and geometry of the Chemehuevi Formation reveal a late Pleistocene sediment pulse into the Lower Colorado River

The Chemehuevi Formation is a distinctive 50−150-m-thick wedge-shaped Pleistocene sedimentary unit deposited by the Colorado River. It lines the perimeters of the river’s floodplains and bedrock canyons for more than 600 km between the mouth of the Grand Canyon and the delta region in the Gulf of California. The formation is composed of a basal tan to light-yellowish-brown and pale-orange mud-dominated facies overlain and interbedded by a light-yellow-brown sand-dominated facies. The unit is one of two extensively exposed aggradational packages in the Lower Colorado River corridor, in addition to a series of other smaller alluvial terrace deposits. The Chemehuevi Formation appears to represent the response of a fully integrated Colorado River system to a significant perturbation, in contrast to the Bullhead Alluvium, which is likely a unique result of Pliocene river integration. The aggradation of the Chemehuevi Formation in the Lower Colorado River corridor may be similarly due to a unique event in the Colorado River system, or it may instead be a well-preserved sedimentary sequence recording typical behavior of the Colorado River below the Grand Canyon in the late Pleistocene. As such, multiple causal mechanisms have been proposed, but no study to date has conclusively explained the Chemehuevi Formation. To help resolve its timing, duration, and origin, we applied post-infrared infrared stimulated luminescence, carbonate U-Th series, and zircon sensitive high-resolution ion microprobe U-Th series geochronology to determine the ages of key exposures of the unit over a wide spatial area. These new data demonstrate that the Chemehuevi Formation was deposited ca. 110−90 ka. The depositional ages collectively overlap, suggesting that deposition occurred rapidly relative to the resolution of the geochronometers. The new depositional timing coincides with a shift from glacial to interglacial conditions after the marine isotope stage 5-6 transition. This observation is consistent with a climate-induced sediment pulse as a causal mechanism, yet correlations with similar deposits in the Colorado River headwaters or in neighboring catchments appear elusive. Potentially, climate transitions between glacial and interglacial periods induced a sediment pulse from hillslopes of the Colorado River system that resulted in the Chemehuevi Formation. An alternative or additional explanation is that the Chemehuevi Formation represents release of lava dam−impounded sediment in the Grand Canyon. The surface geometry of the Chemehuevi Formation projects upstream to the approximate location of lava dams, and the largest possible lava dam impoundment (the Upper Prospect dam) is comparable in volume to the formation. The lava dam hypothesis appears to be a possible explanation for the Chemehuevi Formation. However, tying deposition to a specific lava dam or series of lava dams remains challenging due to discrepancies in timing and volume. The combined effects of a series of lava dams may have led to the Chemehuevi Formation, as the last Pleistocene lava dam eruption coincides with the onset of deposition. Alternatively, the formation may result from the combined effects of both regional climate transitions and the lava dams that created a transient reservoir to compound a climate transition−driven sediment pulse. The geochronologic data presented here do not allow us to distinguish between the lava dam or climate transition hypotheses but will need to be reconciled with any future proposed depositional model.

Arizona, California, Nevada↗

USGS2024

Spatial distribution of API gravity and gas/oil ratios for petroleum accumulations in Upper Cretaceous strata of the San Miguel, Olmos, and Escondido Formations of the south Texas Maverick Basin—Implications for petroleum migration and charge history

The Maverick Basin of south Texas is currently undergoing active exploration and production of gas and oil from tight sandstone reservoirs. The most productive tight sandstones in the basin are in the Upper Cretaceous San Miguel, Olmos, and Escondido Formations. These units are second only to the Eagle Ford Shale in terms of cumulative production volumes. The structural history of the Maverick Basin, from rifting to subsidence to exhumation, has had a profound effect on the characteristics of these reservoirs and the petroleum resources contained therein. This U.S. Geological Survey review of the production history of these strata reflects a recent shift from conventional production to horizontal drilling (unconventional) that exploits low permeability reservoirs in previously overlooked areas of existing oil and gas fields in southern Texas, typically outside of established field boundaries. To investigate the physical properties of the Maverick Basin hydrocarbon accumulations, this case study compiled American Petroleum Institute (API) gravity measurements and calculated cumulative gas/oil ratios (GOR) for thousands of producing wells from the San Miguel, Olmos, and Escondido Formations. Maps were generated from the compiled well production data to show the spatial heterogeneity of API gravity and GOR values for the three formations within the Maverick Basin and immediately outside the basin to the northeast. Within the Maverick Basin, the spatial patterns of API gravity values indicate lighter oils downdip towards the southern basin edge. GOR values indicative of wet and dry gases within the basin are seen interspersed, with values that correspond to black and heavy oils. Differences in the spatial patterns of the petroleum properties within the Maverick Basin are interpreted as effects of Eocene basin inversion caused by Laramide orogenic deformation, and the resulting reservoir exhumation of basin strata. East of the Maverick Basin, spatial distributions of API gravity and GOR values show progressively heavier oils updip to the northwest, grading to dry gases downdip to the southeast, which correlates to the oil and gas windows of the underlying Eagle Ford Shale. Correlation of API gravity and GOR values from the San Miguel, Olmos, and Escondido Formations with thermal maturity data from the Eagle Ford Shale suggests that the Eagle Ford Shale is the petroleum source, and that petroleum migration was approximately vertical for areas to the east of the Maverick Basin. The discontinuity of API gravity and GOR properties within the Maverick Basin implies a complex petroleum charge history, possibly involving the remigration of petroleum and the addition of petroleum from other source intervals in Mexico, to the southwest. Depressurization of exhumed, overpressured reservoirs of the San Miguel, Olmos, and Escondido Formations can explain the intermittent occurrence of gas production throughout the southern Maverick Basin by exsolution of gas from formation brines and the resulting dry gas flushing of hydrocarbon-charged reservoirs. The introduction of dry gas through flushing can, in turn, explain why the patterns of API gravity and GOR values are so dissimilar in the Maverick Basin. This process has implications for possible future production of unconventional resources from undiscovered tight-gas reservoirs in strata of the San Miguel, Olmos, and Escondido Formations, and a different approach to petroleum exploration may be needed in the Maverick Basin relative to exploration techniques applied in other basins within the northern Gulf of Mexico.

Texas↗

USGS2024

Correlation analysis of groundwater and hydrologic data, Kaloko-Honokōhau National Historical Park, Hawai‘i

Designated in 1978, Kaloko-Honokōhau National Historical Park is located on the west coast of the Island of Hawaiʻi. The Kaloko-Honokōhau National Historical Park encompasses about 1,200 acres of coastal land and nearshore ecosystems, which include wetlands, anchialine pools (landlocked bodies of brackish water with hydrologic connections to the ocean), fishponds, a fishtrap, and coral reefs. These nearshore ecosystems are dependent on groundwater discharge with a freshwater component and provide habitat for threatened and endangered, endemic species, such as the orangeblack Hawaiian damselfly ( Megalagrion xanthomelas ) and the Hawaiian coot (ʻAlae keʻokeʻo, Fulica alai ). The populations of these native species, however, are threatened because of habitat loss related to urban development and environmental changes. Kaloko-Honokōhau National Historical Park is within the Keauhou aquifer system and the North Kona District, which experienced a 52 percent resident-population increase between 2000 and 2020 and a 41 percent visitor increase between 2008 and 2019. To support the current water demand associated with this growing population, groundwater is the primary source of freshwater used in the North Kona District, with about 15 million gallons of groundwater withdrawn from the Keauhou aquifer system per day since 2009. With anticipated development, future (2015–35) groundwater withdrawal from the Keauhou aquifer system is projected to be about 55 percent greater than recent (2012–14) withdrawal. Because Kaloko-Honokōhau National Historical Park is located within a coastal aquifer, natural and human-induced changes can affect the quality and quantity of groundwater, which can threaten groundwater-dependent ecosystems. To improve understanding of recent groundwater conditions, the U.S. Geological Survey, in cooperation with the National Park Service, undertook this study to document correlations between hydrologic time-series datasets from sites in and near Kaloko-Honokōhau National Historical Park using the nonparametric (distribution-free) Kendall’s tau statistical test. For the statistical analyses, dependent variables representing the groundwater system include groundwater level, the groundwater-level difference between pairs of sites, and specific conductance, and independent variables include datasets of sea level, rainfall, and groundwater withdrawal. About 34 percent of the 140 non-time-lagged Kendall’s tau statistical tests evaluated in this report are statistically significant ( p -value ≤ 0.050) with generally weak (0.1 ≤ tau ≤ 0.2) to moderate (0.2 ≤ tau ≤ 0.3) correlations. Groundwater levels measured at monitoring sites have the strongest correlation with the multivariate El Niño–Southern Oscillation index and withdrawal from production wells at the nearby Kohanaiki Private Club Community. Specific conductance is not consistently and significantly correlated with the independent hydrologic variables investigated in this report. Because the relations between hydrologic variables are commonly not instantaneous, a second set of correlations was evaluated after applying a range of time lags to the independent variable datasets. Relative to the non-time-lagged case (the set of correlations that did not use time-lagged independent variables), some of the time-lagged independent variables improved correlations with some of the dependent variables. For a particular independent variable, similar time lags were expected between the independent variable and dependent variable at all four monitoring sites. However, different time lags among the four sites sometimes produced the strongest correlations. This study identified several correlations that are statistically significant and hydrologically plausible, but the correlations could indicate that multiple concurrent factors are controlling the observed groundwater-system response, which might be better addressed using multivariate analyses. This study only investigates bivariate correlations, which may not explain all the variance in the data. The correlations analyzed in this report are limited by the quantity of available hydrologic data in the area near Kaloko-Honokōhau National Historical Park and are based on 14 years of time-series data, which were aggregated to a relatively coarse monthly temporal resolution that represents the minimum resolution common to all datasets.

Hawaii↗

USGS2026

High-resolution transboundary vegetation community maps of the Sonoran and Mojave Desert ecoregion to support critical landscape conservation planning and habitat management needs

We produced a 30-m resolution binational land cover map of Bird Conservation Region 33 (BCR 33) for the U.S. North American Bird Conservation Initiative. The region covers large portions of the Sonoran and Mojave Deserts. The map can support the U.S. Fish and Wildlife Service (FWS) Migratory Bird Program’s recovery planning efforts and constitutes the first known binational land cover dataset spanning sections of the United States–Mexico border and using a consistent classification system for both countries. The mapped region includes 152 distinct land cover classes, covering a total area of 38,421,453 ha (148,345 mi 2 ), of which 13,148,345 ha (52,706 mi 2 ) are located in Mexico and 24,770,640 ha (95,639 mi 2 ) in the United States. We primarily used Landsat 8 (OLI) imagery, supplemented by limited ground surveys from two field campaigns, drone-based aerial data, and existing vegetation classification frameworks from both countries. The classification applied a data-fusion approach integrating 30-m Landsat 8 imagery, decadal phenology metrics from vegetation indices, and a random forest model trained mainly with datasets from a comprehensive national mapping project from the U.S. Geological Survey (USGS) GAP Analysis Project (GAP) and federal wildland fire agencies’ Landscape Fire and Resource Management Planning Tools (LANDFIRE) (GAP/LANDFIRE) [United States side] and the National Institute of Statistics and Geography (INEGI) [Mexico side] as well as land cover maps and opportunistic open-access and field observations. Mapping of the full BCR 33 region was carried out in two phases: 1) Phase I, the prototype map, covered a smaller portion of the transboundary area and identified 31 land cover classes, and 2) Phase II, the full BCR 33 map (refer to Figure 1), which resulted in 152 land cover classes. Using a Random Forest classifier, we achieved an overall prediction accuracy of 92% for the Phase I map and 87% for the Phase II full region map. This slight decrease can be attributed to working on a larger, more complex area with a greater number of land cover classes. No formal validation was conducted, aside from using a subset of the collected field observations and training data to assess model performance during and after training. The training sites were further verified using Google Earth (Google, 2026) imagery. Two undergraduate students who worked for over a year visually inspected imagery and open access public images to confirm each training site during model training using in-house developed, online, visual tools. A portion of this field training data was reserved for model validation, and the corresponding results are to be presented in later sections. The project developed an end-to-end, medium- and fine-resolution remote sensing–based data fusion mapping approach. This effort produced a map (Nagler et al., 2025) and the online tools to support a dynamic, live, online map for visualizing the transboundary vegetation communities in BCR 33. The toolset is currently hosted by the University of Arizona (UofA) Vegetation Index and Phenology (VIP) Lab to support FWS partners (https://vip.arizona.edu/viplab_data_explorer?LCM_BCR33). The online map is designed to allow rapid updates using new training, validation, or correction data, making it dynamic and maintainable. The approach we took established a framework for rapid updating and correction of land cover maps, as the model can be quickly retrained with new field observations, updated training data, or other sources. This enables dynamic mapping and change detection of the region’s vegetation. This framework is an advance in data fusion and crowdsourced mapping of complex, vulnerable regions, providing support to regional stakeholders and the wider user community. This transboundary map can inform the protection, conservation, and restoration of vegetation, habitat, and ecosystems, particularly for threatened and endangered species across the two nations using consistent and harmonized binational mapping systems. Beyond supporting land management decisions and stakeholders in the transboundary desert ecoregions, this BCR 33 mapping effort establishes a foundation for future rapid, low-cost, cross-border land cover mapping that can benefit and advance ecosystem management.

Arizona, Baja California, California, Nevada, Sina↗

USGS2023

Prediction of the probability of elevated nitrate concentrations at groundwater depths used for drinking-water supply in the Puget Sound basin, Washington, 2004–19

The Puget Sound basin encompasses the 13,700-square-mile area that drains to the Puget Sound and the adjacent marine waters of Washington State. Well more than 4 million people live within the basin, with numbers continuing to increase, who rely on the basin’s natural resources including groundwater. The Puget Sound Partnership was created by a Washington State statute to implement a science-based recovery of the Puget Sound to help address impacts to these resources. As part of the recovery, the partnership developed the Puget Sound Vital Signs as measures of ecosystem health that guide the assessment of progress toward Puget Sound recovery goals. The Puget Sound Partnership Leadership Council adopted a Drinking Water Vital Sign associated with human health and quality of life, recognizing certain indicators as integral to the sustainability of Puget Sound recovery efforts. One such Vital Sign indicator was the vulnerability of groundwater throughout the aquifers of the Puget Sound basin to elevated nitrate concentrations as defined by the probability of exceeding 2 milligrams/liter (mg/L) at a specific location and well depth. The U.S. Geological Survey (USGS) led the effort to characterize groundwater vulnerability. For this study, groundwater vulnerability refers to a probability with which a contaminant applied at or near the land surface can migrate to the aquifer of interest for a given set of land-use practices. Nitrate concentration data were selected for evaluation because elevated nitrate concentrations are typically caused by anthropogenic activities and have been associated with deleterious impacts on human health. To identify groundwater vulnerability to elevated nitrate concentrations, logistic regression was used to relate anthropogenic (human associated) and natural variables to the occurrence of elevated nitrate concentrations in untreated groundwater from large public water supply system wells found within the Washington State Department of Health Sentry database. Variables that were analyzed included well depth, soil hydraulic conductivity, precipitation, population density, fertilizer application amounts, and land-use types. Statistically significant models that predicted the probabilities of groundwater nitrate concentrations greater than 2 mg/L based on the predictor variables were created for the time periods 2000–04, 2005–09, 2010–14, and 2015–19. For all time periods, well depth and a measure of the abundance of urban and agricultural land over or near the well consistently helped explain the vulnerability of the well to elevated nitrate concentrations defined as a probability of exceeding 2 mg/L of nitrate. Precipitation and (or) soil hydraulic conductivity were also important predictor variables in the models. The models for each time period were used to create maps of groundwater vulnerability at 150- and 300-foot depths throughout the Puget Sound basin. As expected, the most vulnerable locations were associated with shallower well depths and increased agriculture and urban land cover. Across all four time periods, groundwater vulnerability throughout the Puget Sound was low, with probabilities of exceeding 2 mg/L concentrations of nitrate at depths at 150 and 300 feet typically less than 50 percent. Results also found a slight decrease in probabilities of elevated nitrate concentrations throughout the basin over time. More specifically, additional statistical tests found that groundwater with probabilities of less than about 60 percent declined from 2000 to 2019 and represented more than 75 percent of the modeled Puget Sound basin aquifer. Wells with greater than 60 percent probability increased over the same time period but represented only about 25 percent of the aquifer. The maps and statistical analysis presented in the study provide valuable and informative evaluation of the vulnerability of groundwater in the Puget Sound basin to elevated nitrate concentrations. The probability maps do not represent measured nitrate concentrations in groundwater, but rather they present the probability that nitrate concentrations exceed 2 mg/L. The models and predictions from this study are a viable indicator for the Puget Sound Partnership’s Healthy Human Population—Drinking Water Vital Sign. The logistic regression modeling approach presented here benefits water managers by allowing them to assess temporal trends in a range of probabilities, explore vulnerability changes as new regional land cover and anthropogenic data are generated, and distinguish vulnerabilities at different depths within the aquifer.

Washington↗

USGS2025

Peak streamflow trends in Montana and northern Wyoming and their relation to changes in climate, water years 1921–2020

Frequency analysis on annual peak streamflow (hereinafter, peak flow) is essential to water-resources management applications, including critical structure design (for example, bridges and culverts) and floodplain mapping. Nonstationarity is a statistical property of a peak-flow series such that the distributional properties (the mean, variance, or skew) change either gradually (monotonic trend) or abruptly (shift, step change or change point) through time. Not incorporating or accounting for observed nonstationarity into peak-flow frequency analysis might result in a poor representation of the true probability of large floods and thus misrepresent the actual flood risks to life and property. This report summarizes how hydroclimatic variability might affect the temporal and spatial distributions of peak-flow data in the State of Montana (and northern Wyoming) and is part of a larger study to document peak-flow nonstationarity and hydroclimatic changes across a nine-State region consisting of Illinois, Iowa, Michigan, Minnesota, Missouri, Montana, North Dakota, South Dakota, and Wisconsin. A wide range of analyses and statistical approaches are applied to document the primary mechanisms controlling floods and characterize temporal changes in hydroclimatic variables and peak flows. This study was completed in cooperation with the Montana Department of Natural Resources and Conservation. The purpose of this report is to characterize temporal and spatial patterns of nonstationarity in peak flows and hydroclimatology in Montana and northern Wyoming. In this evaluation, peak-flow, daily streamflow, and model-simulated gridded climatic data were examined for monotonic trends, change points, and other statistical properties that might indicate changing climatic and environmental conditions. This report includes background information on the study area, the history of U.S. Geological Survey peak-flow data collection and frequency analysis in Montana, and the review of research relating to hydroclimatic variability and change in Montana. This study might help provide a framework for addressing potential nonstationarity issues in peak-flow frequency updates that commonly are completed by the U.S. Geological Survey in cooperation with other agencies throughout the Nation. The analytical structure of this study includes analyses of monotonic trends and change points in numerous hydroclimatic variables in assigned 30-, 50-, 75-, and 100-year analysis periods. For Montana and part of Wyoming, the 30-, 50-, 75, and 100-year analyses included 157, 70, 48, and 12 streamgages, respectively. For those streamgages, nonstationarities were analyzed in the following variables: (1) climatic variables, including annual and seasonal (winter, spring, summer, and fall) temperature and precipitation; (2) daily streamflow variables, including the annual center of volume duration, annual center of volume median, and peaks over threshold with a mean of four events per year; and (3) annual peak-flow variables, including peak-flow timing and magnitude. A likelihood approach was used to express statistical confidence and assign the nonstationarity results as likely upward or downward (highest statistical confidence), somewhat likely upward or downward (less statistical confidence), or about as likely as not (little statistical confidence; hereinafter, neutral). For the nonstationarity analyses of the climatic, daily streamflow, and peak-flow variables, the results are presented in detail and discussed with respect to statewide patterns and geographic variability. For each of the 30-, 50-, and 75-year analyses, peak-flow change-point and monotonic trend analyses were compiled for streamgages classified with likely downward or likely upward trends. For those streamgages, the associated basin characteristics and nonstationarity results for peak-flow timing, daily streamflow, and climatic variables were investigated and statistically compared to discern associations among other variables that might contribute to the peak-flow nonstationarity results. The 50- and 75-year peak-flow nonstationarities identified in this study are mostly downward, in association with mostly upward temperature and potential evapotranspiration:precipitation monotonic trends. For the 50-, 75-, and 100-year analyses, the peak-flow change points are predominantly downward and are concentrated in the 1970s and 1980s, which indicates general consistency among the longer trend periods. These findings are in association with substantial research documenting globally rising temperature and atmospheric greenhouse gas concentrations that might be largely attributed to anthropogenic activities. Anthropogenic effects might represent long-term (on the order of several decades to more than a century) climate changes that might happen within highly variable natural climate fluctuations. Several paleo studies in the north-central United States have indicated that hydroclimatic extremes (that is, low- and high-streamflow conditions) before European settlement have been outside of extremes since the 1900s. Depending on the interactions of anthropogenic effects and natural climate variability, extreme high-streamflow conditions might occur in the future, even in the presence of long-term downward peak-flow trends.

Montana, Wyoming↗

USGS2024

U.S. Geological Survey Earthquake Hazards Program decadal science strategy, 2024–33

Executive Summary Earthquakes represent one of our Nation’s most significant and costly natural hazards, with estimated annual loses from earthquakes close to $15 billion in 2023. Over the past two centuries, 37 U.S. States have experienced an earthquake exceeding a magnitude of 5, and 50 percent of States have a significant potential for future damaging shaking; these statistics speak to the need for nationwide interest and investment in earthquake hazard characterization and risk reduction. Authorized under the Earthquake Hazards Reduction Authorization Act, the U.S. Geological Survey (USGS) Earthquake Hazards Program (EHP) provides the scientific information, situational awareness, and knowledge necessary to reduce deaths, injuries, and economic losses from earthquakes and earthquake-induced tsunamis, landslides, and soil liquefaction. The EHP supports activities in three focused topical areas: (1) earthquake monitoring, (2) hazard assessment, and (3) applied research, using the results of each—and the coordination among them—to further support risk translation and communication in regions at risk nationwide. For earthquake monitoring, the Advanced National Seismic System (ANSS), a cooperative effort of USGS networks, university partner regional seismic networks, and real-time geodetic networks, collects and analyzes data on earthquakes; issues timely, reliable notifications of their occurrence and impacts; and provides data for earthquake research, hazard, and risk assessment as a foundation for building an earthquake-resilient Nation. The USGS-operated ShakeAlert Earthquake Early Warning system is a recent addition to EHP’s ANSS infrastructure. In the realm of earthquake hazard assessment, the EHP contributes to earthquake risk mitigation strategies by developing the National Seismic Hazard Model and maps, and other related products, that describe the likelihood and potential effects of earthquakes nationwide, especially in the urban areas of highest risk. The EHP also conducts research on the causes, characteristics, and effects of earthquakes and prioritizes work that directly increases the accuracy and precision of earthquake hazards assessments, earthquake forecasts, and earthquake monitoring and situational-awareness products and that supports the Nation’s earthquake mitigation practices. Bridging the EHP’s efforts across research, hazard assessments, and earthquake monitoring is a broad and comprehensive collection of earthquake information products, including the National Seismic Hazard Model, ShakeAlert, and other products describing impact, such as ShakeMap and PAGER (Prompt Assessment of Global Earthquakes for Response), which have been developed and integrated into EHP’s real-time monitoring systems. EHP funds external partners to carry out many important collaborative activities through an active external grants program—one of the largest in the USGS—and through cooperative agreements with other partners such as the university-operated regional seismic networks, funded as part of the ANSS. To continue its support of earthquake hazard characterization and risk reduction, the EHP aims to strengthen its foundational products and practices while positioning itself to respond to the evolving needs of the Nation and follow best practices of the scientific community. This document describes a strategy for the program to ensure it can meet these demands. The foundational priorities outlined in this strategy represent those activities that remain critical to the core functionality of the program and those that can be supported under current fiscal year 2024-level appropriations. Priorities described as aspirational are important for future growth, and to maintain the program’s position as a leading global resource in earthquake science, but would require increases in appropriated funding to be fully realized. Across the program’s portfolio of activities, several major themes have been identified as the most critical activities to advance EHP science over the coming decade. Together, these activities provide the framework necessary to integrate critical hazard characterization and risk reduction activities across the program. They provide the structure for research to advance the understanding of where, when, and why earthquakes occur and how we can use improved knowledge to drive short-term and actionable forecasts of seismic activity. They expand the usefulness of critical earthquake products and advance the sophistication of those products to keep pace with the rapidly evolving needs of an ever-expanding user base while maintaining the position of the USGS as a global leader in earthquake science. Focus on system-level science. Establish an automated earthquake-processing pipeline. Enhance the accuracy and reliability of the ShakeAlert Earthquake Early Warning system and plan for extension to other regions. Implement time-dependent earthquake forecasting. Develop physically realistic models. Expand computational capacity. This science strategy is organized into three primary sections. The first section provides an overview of the EHP and its budget, governance, and program council. Readers familiar with the program may wish to focus on the second section, which describes the core of the science strategy, including priorities across each of the EHP’s major program activities in monitoring, hazard assessment, and targeted research. The third section outlines science priorities that cut across program activities, including those involving collaborations external to the EHP.

American Samoa, Guam, Northern Marianas Islands, U↗