SEARCH · USGS Science

Results for “Geothermics”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16Linked to original sources

USGS2005

Time-dependent seismic tomography of the Coso geothermal area, 1996-2004

The permanent 18-station network of three-component digital seismometers at the seismically active Coso geothermal area, California, provides high-quality microearthquake (MEQ) data that are well suited to investigating temporal variations in structure related to processes within the geothermal reservoir. A preliminary study [Julian, et al., 2003; Julian, et al., 2004] comparing data from 1996 and 2003 found significant variations in the ratio of the seismic wave-speeds, Vp/Vs, at shallow depths over this time interval. This report describes results of a more detailed study of each year from 1996 through 2004.

Conference Paper↗

USGS1999

Regional hydrology of the Dixie Valley geothermal field, Nevada: preliminary interpretations of chemical and isotopic data

Chemical and isotopic analyses of Dixie Valley regional waters indicated several distinct groups ranging in recharge age from Pleistocene (1000a). Geothermal field fluids (~12-14 ka) appear derived from water similar in composition to non thermal groundwater observed today in valley artesian well (also ~14 ka). Geothermal fluid interaction with mafic rocks (Humboldt Lopolith) appears to be common, and significant reaction with granodiorite may also occur. Despite widespread occurrence of carbonate rocks, large scale chemical interaction appears minor. Age asymmetry of the range, more extensive interaction with deep seated waters in the west, and distribution of springs and artesian wells suggest the existence of a regional upward hydrologic gradient with an axis in proximity to the Stillwater range.

Nevada↗

USGS1978

CS 2 and COS in soil gases of the Roosevelt Hot Springs Known Geothermal Resource Area, Beaver County, Utah

Soil-gas samples were collected in two parallel traverses across the Dome fault zone of the Roosevelt Hot Springs Known Geothermal Resource Area. Gas chromatographic analyses of the samples showed anomalous concentrations of CS 3 and COS east of the Dome fault; higher concentrations of CS 2 and COS also occurred over an area in which the hydrothermal system is close to the surface. Measurement of these gases may be useful in exploration for new geothermal sources.

Utah↗

USGS2016

Sources of subsidence at the Salton Sea Geothermal Field

At the Salton Sea Geothermal Field (SSGF) in Southern California, surface deformation associated with geologic processes including sediment compaction, tectonic strain, and fault slip may be augmented by energy production activities. Separating the relative contributions from natural and anthropogenic sources is especially important at the SSGF, which sits at the apex of a complex tectonic transition zone connecting the southern San Andreas Fault with the Imperial Fault; but this has been a challenging task so far. Here we analyze vertical surface velocities obtained from the persistent scatterer InSAR method and find that two of the largest subsidence anomalies can be represented by a set of volumetric strain nuclei at depths comparable to geothermal well completion zones. In contrast, the rates needed to achieve an adequate fit to the magnitudes of subsidence are almost an order of magnitude greater than rates reported for annual changes in aggregate net-production volume, suggesting that the physical mechanism responsible for subsidence at the SSGF is a complicated interplay between natural and anthropogenic sources.

California↗

USGS2010

Are modern geothermal waters in northwest Nevada forming epithermal gold deposits?

Hydrothermal systems currently are active near some gold deposits in northwestern Nevada. Possible links of these modern systems to gold mineralization were evaluated by chemically and isotopically analyzing water samples from the Brady, Dixie Valley, Humboldt House, San Emidio-Empire, Soda Lake, and Wabuska geothermal areas. In addition, quartz veins from Humboldt House and the adjacent Florida Canyon Mine were analyzed to compare ore and gangue phases with those predicted to form from proximal hydrothermal fluids. Nearly all water samples are alkali-chloride-type. Total dissolved solids range from 800 to 3900 mg/L, and pH varies from 5.6 to 7.8. Geochemical modeling with SOLVEQ, WATCH, and CHILLER predict the precipitation of silica in all systems during cooling. Anhydrite, calcite, barite, pyrite, base-metal sulfides, and alumino-silicates are variably saturated at calculated reservoir temperatures and also precipitate during boiling/cooling of some fluids. Measured dissolved gold concentrations are low (<0.2 μg/L), but are generally consistent with contents predicted by equilibrium of sampled solutions with elemental gold at reservoir temperatures. Although the modern geothermal waters can precipitate ore minerals, the low gold and other ore metal concentrations require very large fluid volumes to form a deposit of economic interest.

Conference Paper↗

USGS2017

Micro-seismicity within the Coso Geothermal field, California, from 1996-2012

We extend our previous catalog of seismicity within the Coso Geothermal field by adding over two and a half years of additional data to prior results. In total, we locate over 16 years of seismicity spanning from April 1996 to May of 2012 using a refined velocity model, apply it to all events and utilize differential travel times in relocations to improve the accuracy of event locations. The improved locations elucidate major structural features within the reservoir that we interpret to be faults that contribute to heat and fluid flow within the reservoir. Much of the relocated seismicity remains diffuse between these major structural features, suggesting that a large volume of accessible and distributed fracture porosity is maintained within the geothermal reservoir through ongoing brittle failure. We further track changes in b value and seismic moment release within the reservoir as a whole through time. We find that b values decrease significantly during 2009 and 2010, coincident with the occurrence of a greater number of moderate magnitude earthquakes (3.0 ≤ ML < 4.5). Analysis of spatial variations in seismic moment release between years reveals that localized seismicity tends to spread from regions of high moment release into regions with previously low moment release, akin to aftershock sequences. These results indicate that the Coso reservoir is comprised of a network of fractures at a variety of spatial scales that evolves dynamically over time, with progressive changes in characteristics of microseismicity and inferred fractures and faults that are only evident from a long period of seismic monitoring analyzed using self-consistent methods.

California↗

USGS2018

Irregular focal mechanisms observed at Salton Sea Geothermal Field: Possible influences of anthropogenic stress perturbations

At the Salton Sea Geothermal Field (SSGF), strain accumulation is released through seismic slip and aseismic deformation. Earthquake activity at the SSGF often occurs in swarm-like clusters, some with clear migration patterns. We have identified an earthquake sequence composed entirely of focal mechanisms representing an ambiguous style of faulting, where strikes are similar but deformation occurs due to steeply-dipping normal faults with varied stress states. In order to more accurately determine the style of faulting for these events, we revisit the original waveforms and refine estimates of P and S wave arrival times and displacement amplitudes. We calculate the acceptable focal plane solutions using P-wave polarities and S/P amplitude ratios, and determine the preferred fault plane. Without constraints on local variations in stress, found by inverting the full earthquake catalog, it is difficult to explain the occurrence of such events using standard fault-mechanics and friction. Comparing these variations with the expected poroelastic effects from local production and injection of geothermal fluids suggests that anthropogenic activity could affect the style of faulting.

Conference Paper↗

USGS2020

Machine learning for natural resource assessment: An application to the blind geothermal systems of Nevada

A study is underway to apply machine learning methods to evaluate natural resource potential. In particular, we are considering the search for blind geothermal systems in Nevada. Beginning with the data and experience from the previous Nevada play fairway analysis project, we are building models in TensorFlow/Keras and gaining experience toward predicting the geothermal resource potential as a probability map. During the first year of this project we have encountered several issues particular to using geological and geophysical data sets with these tools. Through an illustrative example we develop a promising workflow for future use as more data become available and are analyzed.

Nevada↗

USGS1978

Models for calculating density and vapor pressure of geothermal brines

In a model for estimating density of a brine, the density of a natural brine at a known temperature, pressure, and composition can be calculated from the densities of the component salt solutions in the complex brine. A model for estimating vapor pressure requires two direct or indirect estimates of the vapor pressure and uses a published "reference-substance principle" to extrapolate,; these data 200° to 300° above the temperature of the highest observation. The methods can be used to estimate the partial molal volume and partial molal enthalpy of H 2 O in the natural brine and the partial molal volume change and partial molal heat change for the H2O component in the vaporization process. The equations for density and vapor pressure and the derived thermochemical properties will help in designing turbines for operation with geothermal and geopressured brines, in optimizing production conditions, and in physical and chemical modeling of a geothermal reservoir.

Journal of Research of the U.S. Geological Survey↗

USGS1976

Geothermal flux through palagonitized tephra, Surtsey, Iceland: The Surtsey temperature-data-relay experiment via Landsat-1

The net geothermal flux through palagonitized basaltic tephra rims of the Surtur I and Surtur II craters at Surtsey, Iceland, in 1972, is estimated at 780 ±325 μ cal cm -2 s -1 , indicating a decline since 1969 when a flux of 1,500 μ cal cm -2 s -1 was estimated. Heat flux in this range characterizes the postvolcanic environment on Surtsey in which the subaerial palagonitization of basaltic tephra is associated with mass transfer of hydrothermal vapor, either of meteoric or sea-water origin, only a few years after cessation of eruptive activity. The flux estimation is the result of the Surtsey data-relay experiment via Landsat-1 which was carried. out in several phases. Successful field installation and test transmissions demonstrated the feasibility of repetitive long-distance (that is, 4,800-km) data transmission and reception from a volcanic environment in Iceland via the Landsat Data Collection System. Temperature data were transmitted for a 38-day period in November and December 1972. A near-surface vertical gradient of 69.4 °C/m was obtained, suggesting a mixed mechanism of heat transfer, partitioned between conduction and convection. Comparison of four methods for estimating fluxes between 500 and 1,500 μ cal cm -2 s -1 , using temperature data derived from the Data Collection Platform, suggests that, where the only temperature available are from the surface and a depth of 1 m, methods of estimating the net geothermal flux from examination of spectral radiance are superior to methods that assume dominant convection or conduction. A computerized thermal-modeling technique to construct parametric diurnal surface-temperature curves is particularly applicable. Flux-estimation methods that assume dominant convection or conduction are limited by the lack of temperature data at greater depths and lack of knowledge of the exact energy partition.

Surtsey↗

USGS2020

He-CO2-N2 isotope and relative abundance characterization of geothermal fluids from the Ethiopian Rift

We report He-CO 2 -N 2 isotopic and relative abundances in free gases and dissolved gas phase of geothermal fluids from the Ethiopian Rift. Fluid samples were collected from ~30 geothermal localities from three key regions throughout rifted and non-rifted areas of Ethiopia. The majority of samples, including off-rift samples, indicate a strong contribution of mantle-derived He-C-N to the fluid samples. Helium ( 3 He/ 4 He) and δ15N-(N 2 ) isotope anomalies are highest (> 15.9RA and > +5.0‰, respectively) at a single locality in south Afar (Sodere), but the maximum δ13C-(CO 2 ) (-0.78‰) is found east of Lake Shalla in the Lake District of the Main Ethiopian Rift. High 3 He/ 4 He values, consistent with mantle plume contributions, are also evident in fluids from the Lake District, where fluids from the Lake Shalla site extend up to 15.5RA. CO 2 / 3 He values span over four orders of magnitude while δ13C-(CO 2 ) values cluster mostly between mantle-like values of -4 and -7‰; only samples east of Lake Shalla display more positive values. Atmospheric-derived nitrogen has likely influenced a number of measured δ15N-(N 2 ) values but following a correction for atmospheric-contamination, the majority of samples reveal positive values (up to 6.5‰) which appear to be coupled to high 3 He/ 4 He values. In regions affected by upwelling mantle plumes, such high values have been interpreted to reflect deep mantle inputs of recycled nitrogen.

Ethiopian Rift↗

USGS2023

Development of small uncrewed aerial systems for multi-instrument geophysical data acquisition in active geothermal systems

Small Uncrewed Aerial Systems (sUAS) serve as critical platforms for geophysical data collection at an intermediate scale between lower resolution, regional datasets collected via crewed aerial surveys, and high resolution, but spatially sparse sampling of ground-based data collection methods. Advances in sensor design and sUAS capabilities have led to rapid advances in the amount and type of geophysical data that can be acquired using sUAS-based survey designs (Gavazzi et al., 2019). Here we showcase the utility of a single sUAS (the Matrice 600 Pro and accompanying sensor package) that collects magnetic, thermal infra-red (TIR) and gas (CO2, SO2, H2S, water vapor) data for use in geothermal resource exploration and monitoring, with case studies in eastern California and Iceland. The work highlights the flexibility of modern sUAS systems for single-team acquisition of multiple independent but coupled geophysical data which allow for a multidisciplinary approach to geothermal systems research. We summarize the workflows involved in collecting each dataset as well as several common issues encountered both during data collection and data processing.

Conference Paper↗

USGS2024

Summary of annual repeat magnetotelluric surveys of the Geysers geothermal field

As part of a multi-year project, funded by the California Energy Commission, annual magnetotelluric (MT) surveys have been collected at The Geysers geothermal field in northern California with the goal of measuring temporal changes within the steam field. The repeat surveys started in 2021 and repeated a 2017 survey (Peacock et al., 2020) with further extension to the southern part of the geothermal field. Temporal variations in the MT transfer functions are observed to be spatially coherent and compartmentalized. Mapping residual phase tensor ellipses demonstrates the direction of maximum change is often aligned with existing fracture orientations. Three dimensional inversion of the MT data, using the inversion results from previous years as the starting model, indicates that the steam reservoir has generally become more resistive over time (~10%), suggesting more steam in the field. A few pockets within the steam field have become more electrically conductive over time and are collocated with injection wells, suggesting either more fluid content in those zones, less steam, or more saline fluids.

California↗

USGS2018

A geophysical characterization of the structural framework of the Camas Prairie Geothermal System, southcentral Idaho

Play Fairway Analysis methods, utilizing existing geologic, thermal, geochemical, and geophysical data were employed in an initial assessment of geothermal resources in the Snake River Plain. These efforts identified the Camas Prairie in southcentral Idaho as a region with elevated resource potential. Subsequent efforts included structural and geophysical data collection to identify the most favorable structural settings for exploiting resources in the valley. The present work involved high-resolution gravity, magnetic, magnetotellurics (MT), field mapping, and seismic surveys to further characterize the system and target sites for exploration drilling around Barron’s Hot Springs (BHS) in the southwest part of the valley. Geophysical mapping and modeling reveal that the BHS coincides with a complex intersection of two major fault systems: a prominent NW-trending system that includes the Pothole fault, and EW-trending basin-bounding faults that control NS-extension. This complex zone includes a dense network of EW-oriented faults and a right stepover in the Pothole fault which, given the dominant dextral-normal to normal slip inferred for this fault, would promote extension in the immediate vicinity of the BHS. Surface faulting in this region indicate Pleistocene or younger slip, and seismic imaging documents offsets of shallow strata that suggest ongoing activity on these structures. MT modeling results show that this zone also coincides with a prominent conductive anomaly, characteristic of the presence of hydrothermal alteration or hydrothermal fluids. These results point to the importance of these structures in maintaining current and long-lived shallow hydrothermal activity around the BHS. The detailed structural mapping and conceptual framework developed from this study provide critical constraints for siting a drill hole aimed at documenting reservoir characteristics and informing potential future development of these geothermal resources.

Idaho↗

USGS2024

Geophysical modeling of a possible blind geothermal system near Battle Mountain, NV

The northeastern portion of the Reese River basin in north-central Nevada is the focus of detailed geophysical and geological studies as part of the INGENIOUS project, which aims to identify new, commercially viable hidden geothermal systems in the Great Basin region of the western U.S. This location, herein referred to as Argenta Rise, occupies a broad (~15km wide) left-step between major range-front fault systems along the northwestern edge of the Shoshone Range and Argenta Rim, with numerous ENE-striking intra-basin faults presumably accommodating sinistral-normal oblique slip across the step-over. Four discrete regions have been identified within the study area that have favorable structural settings for hosting a blind hydrothermal system. However, with no definitive or extensive surface manifestations of an active hydrothermal system (e.g., geysers, steam vents, sinter, etc.), detailed geophysical studies are necessary to resolve subsurface geology and structure, and identify zones of enhanced structural complexity that may promote hydrothermal fluid flow. Hence, we collected high-resolution gravity, MT, and rock property data (density, magnetic susceptibility), and analyzed the recently acquired GeoDAWN aeromagnetic data to characterize potential geothermal resources in this region. Using the new geophysical datasets, we jointly modeled gravity and magnetic data along a series of intersecting 2D profiles that integrated information from recent, local-scale fault mapping. Rock property measurements performed on outcrops and hand samples throughout the study area constrained the models. The MT data were used to construct a 3D resistivity model that highlights the location of inferred alteration and fluids in the subsurface. Combined MT and potential field results reveal which structures may be most important for controlling hydrothermal fluid migration, as well as which geologic units may host hydrothermal fluids. Our gravity derived depth to basement surface coincides well with the base of shallow conductive anomalies, suggesting hydrothermal fluids may be confined to basin fill sediments and volcanics. This work supports our development of 3D geophysical and geologic models that are focused along the western flank of the northern Shoshone Range and aids the process of selecting sites for temperature gradient drilling.

Nevada↗

USGS2025

Estimation of the accessible and useful resource base for electric-grade enhanced geothermal systems (EGS) resources of the Great Basin, USA

Scientists with the U.S. Geological Survey (USGS) recently completed a provisional assessment of the electric-grade geothermal resources associated with the low-permeability geologic formations of the Great Basin, USA, where resources are assumed to be accessible using enhanced geothermal systems (EGS) technologies (i.e., the engineering of sufficient permeability to facilitate efficient heat extraction). This assessment required estimation of the accessible resource base (electric-grade heat [>90ºC] at depths where drilling and stimulation are deemed achievable using current technology) and useful resource (heat that can be extracted from the accessible region). Electric-grade heat can be estimated from existing temperature models. The accessible resource base can be estimated as the electric-grade heat that exists at depths shallower than 6 km based on the limitations of current drilling and stimulation technologies, along with evidence for sustained natural fracture conductivity at depth. The useful part of the accessible heat can be estimated as the product of three efficiencies and factors: the heat extraction efficiency, the viable geology factor, and the reservoir spacing efficiency. The accessible and useful parts of the resource can be estimated in units of heat, or in units of electric power using an electrical conversion efficiency, which is a function of resource temperature. We also estimate the ranges for each of the efficiencies and describe the motivations behind the choice of best estimates used for the recent assessment. An analytic solution is provided for the useful resource above any depth (in units of electric power), where efficiency estimation assumes nearly steady heat extraction rates that cool reservoirs to 90ºC over 30 years of power generation.

Great Basin↗

USGS1974

Flashing flow in hot water geothermal wells

The production characteristics of hot-water geothermal wells which flash to steam-water mixtures in the cased part of the hole were-analyzed. The flashing flow is assumed to be isenthalpic and, for purposes of calculating pressure drop, a finely dispersed mixture of equal average velocity. Water flow in the aquifer is treated using steady, radial Darcy flow. Calculations for a typical geothermal well show the effects on production of varying the system parameters of aquifer permeability, depth to water table, and base temperature. Field data from Wairakei, New Zealand, demonstrate the reductions in flow caused by mineral deposits in the bore. Data from Imperial Valley, Calif., agree well with calculated results.

Journal of Research of the U.S. Geological Survey↗

USGS1973

Production of superheated steam from vapor-dominated geothermal reservoirs

Vapor-dominated geothermal systems such as Larderello, Italy, The Geysers, California, and Matsukawa, Japan yield dry or superheated steam when exploited. Models for these systems are examined along with production data and the thermodynamic properties of water, steam and rock. It is concluded that these systems initially consist of a water and steam filled reservoir, a water-saturated cap rock, and a water or brine-saturated deep reservoir below a water table. Most liquid water in all parts of the system is relatively immobilized in small pores and crevices; steam dominates the large fractures and voids of the reservoir and is the continuous, pressure-controlling phase. With production, the pressure is lowered and the liquid water boils, causing massive transfer of heat from the rock and its eventual drying. Passage of steam through already dried rock produces superheating. After an initial vaporization of liquid water in the reservoir, the decrease in pressure produces increased boiling below the deep water table. With heavy exploitation, boiling extends deeper into hotter rock and the temperature of the steam increases. This model explains most features of the published production behavior of these systems and can be used to guide exploitation policies.

Geothermics↗