USGS ScienceSearch

SEARCH · USGS Science

Results for “Applied and Environmental Microbiology”

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,657 records · Page 16Linked to original sources

Pesticides in surface water from three agricultural basins in south-central Georgia, 1993-97

Twenty-two of 43 pesticides analyzed were detected in 128 water samples collected from the Tucsawhatchee Creek, the Little River, and the Withlacoochee River. These streams drain agricultural basins in south-central Georgia and were sampled from March 1993 through June 1995. Herbicides were detected more frequently than insecticides. The most frequently detected herbicides were atrazine and metolachlor and the most frequently detected insecticide was carbaryl. Pesticide concentrations in the three streams were low and did not exceed U.S. Environmental Protection Agency drinking water standards. The maximum pesticide concentration was 2.6 mg/L (micrograms per liter) for propargite, a miticide detected in only one sample. The maximum concentrations of the remaining 21 pesticides were less than 0.25 mg/L. The median concentrations were equal to the method detection limit for all pesticides except atrazine (0.008 mg/L) and metolachlor (0.012 mg/L). The ratio of herbicide detections to nondetections was largest in the planting season, smaller in the harvest season and smallest in the fallow season for the three basins. The same pattern existed for the insecticide ratios in the Little River and the Withlacoochee River. Pairwise correlations between concentrations of atrazine and metolachlor, and four parameters (discharge, and concentrations of dissolved organic carbon, suspended organic carbon, and suspended sediment) were evaluated for each stream. The strongest correlations existed between metolachlor and mean daily discharge, and metolachlor and sediment in the Withlacoochee River. The only significant correlation for the Little River was between atrazine and suspended sediment.

Georgia

Prioritizing US Geological Survey science on salinization and salinity in candidate and selected priority river basins

The US Geological Survey (USGS) is selecting and prioritizing basins, known as Integrated Water Science basins, for monitoring and intensive study. Previous efforts to aid in this selection process include a scientifically defensible and quantitative assessment of basins facing human-caused water resource challenges (Van Metre et al. in Environmental Monitoring and Assessment , 192(7), 458 2020). In the present work, we explore this ranking process based on water quality considerations, specifically salinity and salinization. We selected top candidate basins to study salinity and salinization issues in 18 hydrologic regions that include 163 candidate basins. Our prioritization is based on quantitative assessment of sources of salinity, drivers of change, and receptors that must respond to those sources and drivers. Source terms represented in the prioritization include geology, depth to brackish groundwater, stream conductivity, chloride in precipitation, urban and agricultural land use, application of road salt as a deicer, and irrigation. Drivers represented in prioritization include changes in chemical weathering as a result of changes in rainwater chemistry. Receptors include measures of water stress, measurements of stream ecological health, and socioeconomic factors. In addition, we present research activities for the USGS on salinity and salinization that can be pursued in these basins including assessment of sources, pathways, and loadings; predicting and understanding changes in sources, peaks, and trends; understanding the components of salinity and mobilization of contaminants; understanding the relationship between salinization and changing ecosystems; and developing knowledge on the causes and distribution of groundwater salinity, brackish water resources, and challenges related to desalination.

Enviornmental Monitoring and Assessment

Participatory engagement to reduce communication gaps

Underserved communities, especially those in coastal areas in Puerto Rico, face significant threats from natural hazards such as hurricanes and rising sea levels. Limited funding hinders the investment in costly mitigation measures, increasing exposure to natural disasters. Providing coastal resources and data products through effective communication mechanisms is fundamental to improving the well-being of these underserved coastal communities. The overall objectives of the pilot effort to engage and connect with underserved coastal communities in Puerto Rico were the following: (1) compile a comprehensive database of the projects and resources relevant to natural hazards in Puerto Rico; (2) foster connections with Puerto Rican interested parties to better understand their priorities regarding coastal hazards and provide them with pertinent U.S. Geological Survey (USGS) resources; and (3) identify knowledge gaps to guide future USGS projects in Puerto Rico. Here we outline our participatory engagement framework and process, along with two specific resources developed with the information collected from this effort. These resources are available in English and Spanish and consist of user-friendly, non-technical information products. Among them are: (1) a website where users can learn about USGS research on landslides, hurricanes, earthquakes, water resources, coastal hazards, tsunamis, and ecosystem hazards and environmental contaminants, and (2) a geonarrative highlighting shoreline changes in Puerto Rico with sections on historical shoreline trends, hurricane impacts, and potential solutions that could help protect communities and mitigate coastal hazards. Continuing participatory engagement in future projects could enhance the accessibility and usability of natural hazards resources within the community.

San Juan

Dynamic baseflow storage estimates and the role of topography, geology and evapotranspiration on streamflow recession characteristics in the Neversink Reservoir Watershed, New York

Estimates of dynamic groundwater volumes supplying baseflow to streams are important for water availability projections during extended periods of drought. The primary goals of this study were to provide dynamic storage volume estimates, inferred from streamflow recession analysis, for baseflow regimes within seven gaged catchments within the Neversink Reservoir Watershed (NRW), a critical municipal water source for New York City. Additionally, geomorphological properties, surficial geology and hydro-meteorological processes were quantified and described in relation to time and spatially variable recession behaviour and storage estimates across the NRW. To explore these relationships, we (1) evaluated seasonal trends in streamflow recession behaviour in relation to modelled potential evapotranspiration (PET) and catchment runoff rates, (2) derived empirical streamflow models for cool-season runoff using both linear and nonlinear reservoir assumptions for baseflow and (3) calculated metrics related to the geology and geomorphology of each catchment and compared these metrics to area normalised baseflow dynamic storage estimates. Results show that baseflow recession behaves as a nonlinear reservoir, and applying linear groundwater reservoir assumptions may underestimate the total dynamic storage volumes compared to what would be predicted for a nonlinear reservoir. Increases in PET caused decreases in storage conditions that resulted in increased recession rates and nonlinearity in streamflow recession during the growing season. Additionally, we found that while no single physical catchment characteristic solely predicted catchment storage dynamics, sediment volume and stream gradients were stronger predictors of normalised storage volumes than catchment surface area or surface topography alone. Within the NRW, catchments with the highest sediment volume exhibited the lowest recession rates and higher dynamic storage volumes, while the smallest catchment, mostly devoid of sediment, had the fastest recession rate and lowest dynamic storage volume.

New York

Is satellite-derived bathymetry vertical accuracy dependent on satellite mission and processing method?

This research focusses on three satellite-derived bathymetry methods and optical satellite instruments: (1) a stereo photogrammetry bathymetry module (SaTSeaD) developed for the NASA Ames stereo pipeline open-source software (version 3.6.0) using stereo WorldView data; (2) physics-based radiative transfer equations (PBSDB) using Landsat data; and (3) a modified composite band-ratio method for Sentinel-2 (SatBathy) with an initial simplified calibration, followed by a more rigorous linear regression against in situ bathymetry data. All methods were tested in three different areas with different geological and environmental conditions, Cabo Rojo, Puerto Rico; Key West, Florida; and Cocos Lagoon and Achang Flat Reef Preserve, Guam. It is demonstrated that all satellite derived bathymetry (SDB) methods have increased accuracy when the results are aligned with higher-accuracy ICESat-2 ATL24 track bathymetry data using the iterative closest point (ICP). SDB vertical accuracy depends more on location characteristics than the method or optical satellite instrument used. All error metrics considered (mean absolute error, median absolute deviation, and root mean square error) can be less than 5% of the maximum bathymetry depth penetration for at least one method, although not necessarily for the same method for all sites. The SDB error distribution tends to be bimodal irrespective of method, satellite instrument, alignment, site, or maximum bathymetry depth, leading to the potential ineffectiveness of traditional error metrics, such as the root mean square error. However, our analysis demonstrates that performing detrending where possible can achieve an error distribution as close to normality as possible for which error metrics are more diagnostic.

Florida

Representation of surface-water flows using Gradient-Related Discharge in an Everglades Network

The Everglades Depth Estimation Network interpolates water-level gage data to produce daily water-level elevations for the Everglades in south Florida. These elevations were used to estimate flow vectors (gradients and directions) and volumetric flow rates using the Gradient-Related Discharge in an Everglades Network (GARDEN) application developed by the U.S. Geological Survey in cooperation with the U.S. Army Corps of Engineers. Flow rates in both the east-west and north-south directions were computed on a 400-meter square grid using modified parameters in the Manning’s equation. The frictional resistance parameter in the Manning’s equation was calibrated to measured flow rates at coastal creeks fed by Everglades Depth Estimation Network boundary flows. Levees and other features that act as barriers to flow were defined as “no-flow” grid cells where vectors were set to zero. The flow volume magnitudes were calibrated with 2020 daily values of coastal river flows, and verification was performed using 2021 data. Within a given day, the measured coastal river flows fluctuate more than the GARDEN boundary flows because of tidal and wind forcings. Because the GARDEN boundary flows were the upstream water source for the coastal rivers, calibration focused on matching average daily flow volumes rather than daily fluctuations. The Pearson’s correlation coefficient is 0.766 for the 2020 calibration period and 0.566 for the 2021 verification period. Applying GARDEN to periods with hydraulic-control-structure releases allows the propagation of structure flows to be seen in the daily flow-vector maps along with the multiday response of flows farther downgradient. Flow vectors may be overestimated near control structures because of difficulties in resolving the water gradient downstream from the structure. Flow vectors farther from the structure are more accurate than those near the structure.

Florida

Rapid seismic and infrasound assessment of large landslides: A case study from Denali National Park and Preserve (Alaska)

Large, rapid landslides are a global hazard that can occur in remote, mountainous areas. Eyewitness reports of landslides and satellite imagery can often be limited or delayed, particularly during inclement weather. However, landslide-generated seismic and infrasound (low-frequency atmospheric sound) waves can be remotely detected in near real-time. This information can significantly expedite characterization and possible landslide response activities. Here, we highlight these capabilities using a > 4 million m³ ice–rock avalanche in Denali National Park and Preserve (Alaska). This event was detected via a landslide-specific seismic location and volume estimation algorithm deployed in Alaska, and — notably — by standard earthquake monitoring systems. Following rapid detection of this event, we combined its seismic and infrasound dataset with optical, synthetic aperture radar, and oblique aerial imagery, multitemporal digital elevation models, and a numerical flow model to reconstruct its failure timeline and dynamics. We apply array processing to infrasound signals traveling > 250 km and find that two precursory events occurred minutes prior to the main failure. We use long-period seismic signals to infer the force exerted by the landslide on the Earth and constrain the rheological parameters of our numerical flow simulation with this result and deposit morphology. The main failure produced a steeply-dipping impulsive initial downward force and reached speeds exceeding 60 m/s. This impulsive force generated relatively strong seismic body waves, which contributed to the earthquake system detection. This large, remote Alaska landslide underscores the key value of seismic and infrasound analysis for rapid landslide assessment and motivates efforts to further operationalize these approaches.

Alaska

Dendroseismological investigation of redwood trees along the North Coast section of the San Andreas Fault

Sequoia sempervirens (coast redwood) tree rings have the potential to annually resolve late-Holocene earthquakes on the northern San Andreas Fault based on direct (e.g., physical damage) and indirect (e.g., co-seismic environmental change) impacts, but scarcity of suitable samples and challenges crossdating this long-lived species have limited progress. More precise dating of the pre-1906 (penultimate) earthquake can improve hazard assessment and understanding of rupture segmentation. We target old trees (maximum >815 yr) along the North Coast section of the fault (increment cores via rope-climbing, 11 living trees; plunge cuts, 23 stumps) and employ complementary disturbance detection methods including radial-growth averaging (tree- and series-level), cataloging anatomical indicators (e.g., traumatic resin ducts, TRD), and dating structural components (e.g., reiterated trunks, leans). Multi-centennial ring-width chronologies at Fort Ross (1569−2023) and Gualala (1397−2023) promote continued study with incomplete crossdating limiting utilization of some series. Growth pulses (reductions, releases) and TRD dispersed across the record reflect dynamic environments that obfuscate detection of earthquake signals. The 1906 earthquake did not leave strong signatures on most trees, and when it did, within-tree response varied from normal presentation to discoloration, TRD, and missing rings. Synchrony of indicators at both locations identified 1678−1680 (6 of 15 trees) and 1698−1700 (8 of 16 trees) as the strongest disturbances among dated rings in the time range of the penultimate earthquake, peaking at 1698 (15.7 % of possible growth and anatomical indicators), but the triggering mechanisms for these events are unknown.

California

Abandonment of the Upper Devonian Greenland Gap Group and Scherr Formation and revision of the Upper Devonian Brallier and Foreknobs Formations in the central Valley and Ridge Province

This study revises the lithostratigraphic framework of the Upper Devonian interval traditionally assigned to the Greenland Gap Group across the central Appalachian Valley and Ridge Province. The work aims to modernize and standardize lithostratigraphic nomenclature, establish a new reference section and demonstrate how the revised stratigraphy improves edge-matching of 1:24,000 scale geologic maps and supports compilation mapping at scales of 1:100,000 and larger. The revision eliminates the names Greenland Gap Group, Scherr Formation and the Minnehaha Springs Member of the Scherr Formation; reassigns all strata previously designated as Scherr Formation by Dennison (1970) to the upper Brallier Formation; and abandons the basal Mallow Member of the Foreknobs Formation, placing its strata within the upper Brallier as originally defined by Butts (1918). The contact between the Brallier and Foreknobs formations is placed at the base of the first mappable, ridge-forming package of fine- to coarse-grained, cross-bedded, sandstone beds, often containing rounded quartz pebbles with minor interbeds of shale and siltstone. This contact may be gradational in places but, even in absence of good exposure, can usually be distinguished topographically in recently produced lidar-derived imagery as having elevated relief due to the presence of more resistant, compositionally mature coarse-grained sandstone-rich strata. Applying this criterion for mapping the contact between the Brallier and Foreknobs formations has resulted in reconciliation of mismatches of geologic contacts along several 7.5-minute quadrangle boundaries in the states of Virginia, West Virginia, Maryland and Pennsylvania. A new reference section at Baker, West Virginia showcases the contacts between the Harrell Shale, Brallier Formation, Foreknobs Formation and Hampshire Formation. A digital outcrop model of the reference section is provided for future preservation.

Maryland, Pennsylvania, Virginia, West Virginia

Simulation of groundwater flow to evaluate hydrogeologic controls on a PFAS plume, Coakley Landfill Superfund Site, Rockingham County, New Hampshire

Per- and polyfluoroalkyl substances (PFAS), including perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS), have been detected at combined concentrations above 2,000 nanograms per liter (ng/L) at groundwater seep locations near the Coakley Landfill Superfund site, in North Hampton, New Hampshire. The landfill was active from 1972 to 1985. An impermeable cap was placed on the landfill in 1998. The adjacent area to the Coakley Landfill has many water supply wells, and transport of PFAS compounds to the wells is a concern. Fracture anisotropy in the underlying bedrock aquifer complicates the understanding of PFAS transport because groundwater preferentially travels along fractures that may not align with the prevailing groundwater flow direction. In 2018, the U.S Environmental Protection Agency and the U.S. Geological Survey began an investigation of the groundwater flow from the Coakley Landfill site. This report describes the modification of a numerical groundwater-flow model for the local area around the Coakley Landfill and summarizes findings of the investigation. In addition, this report includes a brief description of PFOA and PFOS occurrence, a discussion of model construction, evaluation of model performance through calibration, and discussion of simulation results for two periods (before and after capping). Limitations are also discussed. Results show that simulated groundwater flow moves from the Coakley Landfill to the west and north. Advective transport modeling using particle tracking shows that groundwater from the landfill discharges primarily to streams to the west and north, and a small amount is transported to distal wells. Dilution of contaminants through advection and dispersion likely plays a role in whether PFAS compounds from the landfill will be detected above laboratory reporting levels at distal wells.

EarthArXiv

Analysis of nutrients in the surface waters of the Georgia–Florida Coastal Plain study unit, 1970–91

During the early phase of the Georgia-Florida National Water Quality Assessment study, existing information on nutrients was compiled and analyzed in order to evaluate the nutrient concentrations within the 61,545 square mile study unit. Evaluation of the nutrient concentrations collected at surface-water sites between October 1, 1970, and September 30, 1991, utilized the environmental characteristics of land resource provinces, land use, and nonpoint and point-source discharges within the study unit. Long-term trends were investigated to determine the temporal distribution of nutrient concentrations. In order to determine a level of concern for nutrient concentrations, the U.S. Environmental Protection Agency (USEPA) guidelines were used: (1) for nitrate concentrations, the maximum contaminant level in public-drinking water supplies (10 mg/L); (2) for ammonia concentrations, the chronic exposure of aquatic organisms to un-ionized ammonia (2.1 mg/L); (3) for total-phosphorus concentrations, the recommended concentration in flowing water to discourage excessive growth of aquatic plants (0.1 mg/L); and (4) for kjeldahl concentrations, however, no guidelines were available. For sites within the 10 major river basins, median nutrient concentrations were enerally below USEPA guidelines, except for total-phosphorus concentrations where 45 percent of the medians exceeded the guideline. The only median ammonia concentration that exceeded the guideline occurred at the Swift Creek site (3.4 mg/L), in the Suwannee River basin, perhaps due to wastewater discharges. For all sites within the Withlacoochee, Aucilla, and St. Marys River basins, median concentrations of nitrate, ammonia, and total phosphorus were below the USEPA guidelines. Nutrient data at each monitoring site within each major basin were aggregated for comparisons of median nutrient concentrations among major basins. The Ochlockonee and Hillsborough River basins had the highest median nutrient concentrations, the Aucilla River basin had the lowest. Median concentrations of nitrate and ammonia among all major basins were below USEPA guidelines. The median total-phosphorus concentrations for the following river basins exceeded the USEPA guideline: Hillsborough, St. Johns, Suwannee, Ochlockonee, Satilla, Altamaha, and Ogeechee. Although nutrient concentrations within the study unit were low, long-term increasing trends were found in all four nutrients. All 18 study-unit wide nitrate trends had increasing slopes ranging from less than 0.01 to 0.07 (mg/L)/yr. The range in slope for the 13 ammonia trends was -0.03 to 0.01 (mg/L)/yr with 6 increasing trends in the northern part of the study unit. Of the 17 total-phosphorus trends found in the study unit, 10 were found at sites where the median concentration exceeded the USEPA guideline. At these 10 sites, 4 sites had increasing trends with slopes ranging from less than 0.01 to 0.07 (mg/L)/yr, 5 sites had decreasing trends with slopes ranging from -0.01 to -0.24 (mg/L)/yr, and one site showed a seasonal concentration trend. Median nutrient concentrations were significantly different among the four land resource provinces: Southern Piedmont, Southern Coastal Plain, Coastal Flatwoods, and Central Florida Ridge. As a result, nutrient concentrations among basins with similar nutrient inputs but located within different land resource provinces are not expected to be the same due to differences in the combination of factors such as soil permeability, runoff rates, and stream channel slopes. This concept is an important consideration in designing a surface-water quality network within the study area. For the most part, the Coastal Flatwoods showed the lowest median nutrient concentrations and the Southern Coastal Plain had the highest median nutrient concentrations. Lower median nitrate concentrations in surface-water basins were associated with the forest/wetland land-use category and higher median concentrations of nitrate and ammonia with the urban category when land-use percentages were classified into four land-use categories (agriculture, forest/wetland, mixed, and urban). These results were reasonable based on expected high nutrient inputs from urban areas and low inputs from forested and wetland areas. However, the lack of association between high nutrient concentrations and the agricultural land-use category was not expected since high nutrient inputs are generally needed for agriculture production.

Florida, Georgia

Stream habitat characteristics at selected sites in the Georgia-Florida coastal plain

Habitat characterization is part of a multidisciplinary approach to water-quality assessment implemented by the National Water-Quality Assessment Program. Habitat data were collected in the Georgia-Florida Coastal Plain study unit at 24 sites during 1993-95. Data were collected for habitat characteristics at three spatial scales: basin, segment, and reach. Basin data include physiography, land resource provinces, and land use, providing a description of the environmental setting at each site. Segment data include length, gradient, and sinuosity. A Kendall correlation analysis performed on segment characteristics and the log-of-basin area showed a correlation between segment gradient and the log-of-basin area and a correlation between sinuosity and segment length. Reach data consist of field-collected measurements of both instream and riparian habitats. Sand and detritus were the most common channel-bed substrates among the sampled sites. Measurements of channel width, water depth, and bank width and height were used to create cross-sectional profiles of each sampled area. Elevations of selected durations plotted on cross sections illustrated the percentage of time that the banks were inundated at each site. Sites were divided into two groups based on duration of bank inundation (less than or equal to 1 percent and greater than 1 percent). Bank woody vegetation was also sampled and a clustering algorithm known as Two-Way INdicator SPecies ANalysis (TWINSPAN) was used to analyze these data. TWINSPAN divided the sites into two groups based on their vegetation composition. A statistical comparison of the two types of site groups (duration of bank inundation and vegetation) was performed. The significant association between these groups was consistent with the hypothesis that inundation frequency affected riparian vegetation.

Florida, Georgia

Diverging mineral chemistry of iron and nickel throughout Earth’s changing redox conditions reveals foundation for their evolution as protein cofactors

Iron (Fe) and nickel (Ni) were both foundational to early metabolism, yet their biological trajectories diverged as Earth’s surface redox state changed. Here, we integrate mineral chemistry network analysis, protein metal-site coordination-sphere analysis, and curated redox comparisons to test how geochemistry and metalloprotein architecture co-evolved. Mineral network analyses show broader electronegativity variation and network diversity for Fe-bearing minerals through time relative to Ni-bearing minerals. In structural analyses of protein metal centers in a combined Fe/Ni protein structure set, it is shown that Fe- and Ni-associated environments differ in amino-acid composition, hydropathy structure, and cysteine representation. The greater chemical diversity and electronegativity variation in Fe minerals mirror the higher redox and structural versatility of Fe-binding proteins. The presence of Fe in a broader range of mineral and protein environments demonstrates the chemical adaptability of the metal, from the anoxic Archean to oxidative Earth surface conditions following the Great Oxidation Event. Iron, with its broad redox potential range in Fe-oxidoreductases, has a central role in both anaerobic and aerobic metabolisms. Nickel, by contrast, is less widespread in biology. Today, Ni is predominantly employed in deeply branching anaerobic pathways and by proteins with narrower redox potential ranges. Our results show that evolutionary processes, constrained by metal chemistry, habitually utilize Fe as a redox generalist while retaining Ni in specialized roles. The divergent paths of Ni and Fe, from rocks to proteins, demonstrate the intimate relationship between planetary geochemistry and metabolic origins on Earth and suggest that Fe/Ni geochemistry may inform habitability assessments in extraterrestrial environments when interpreted within specific planetary environmental contexts.

Life

Incorporating location uncertainty improves inference with stop-level North American Breeding Bird Survey data

Ecological models should account for uncertainty to be most effective and useful. Yet, uncertainty from model covariates—unlike that from other sources, such as sampling error or process variability—is seldom explicitly incorporated. This can cause underestimates of uncertainty to cascade through model parameter estimates, predictions, and downstream uses. Burner et al. proposed a method for quantifying uncertainty in covariates and incorporating it into models using informative Bayesian priors. This method was applied to stop-level Breeding Bird Survey (BBS) analyses, where land cover uncertainty at each stop arises from substantial stop location uncertainty. A limited validation of model-estimated land cover, using stops with known locations, indicated the method’s potential effectiveness, but it was not rigorously evaluated. We conduct a robust simulation-based test, generating stop locations, extracting land cover, and simulating bird communities across 210 BBS routes in the upper Midwest. We compare 3 models: a “known” model with true land cover, a “naive” model assuming consistent 800-m stop spacing, and a “full” model using informative priors to estimate land cover. Species parameter estimates and predicted prevalence patterns across gradients in land cover from the full model approached those of the known model and were substantially closer to the true values used in simulations relative to those from the naive model. Naive model parameters were more biased relative to the other models, and credible intervals of predicted species prevalence rarely included the true simulated values. The full model also produced land cover covariate estimates closer to true simulation values relative to the mean informative priors. Our results show that, for the BBS, informative priors enable more accurate stop-level analyses despite location uncertainty. In contrast, naive models that ignore this uncertainty yield poor inferences. More broadly, we demonstrate empirically the utility of informative priors to account for covariate uncertainty in ecological models.

Michigan, Minnesota, Wisconson

Modeling seawater intrusion along the Alabama coastline using physical and machine learning models to evaluate the effects of multiscale natural and anthropogenic stresses

Seawater intrusion threatens groundwater resources in coastal regions, including southern Baldwin County, Alabama, where the freshwater-saltwater interface dynamics remain poorly understood. To address this gap, this study uses combined physics-based and machine-learning models to quantify seawater intrusion caused by natural (storm surges) and anthropogenic (human activities) perturbations. The long short-term memory network and wavelet analysis were used to assess vertical aquifer vulnerabilities, revealing that the shallow part of the Coastal lowlands aquifer system (CL1) in the southern Baldwin County region is more susceptible to sea level rise and groundwater extraction than deeper aquifers. Based on these findings, a cross-sectional numerical model (physics approach) for the CL1 aquifer was developed to evaluate tidal and storm surge effects, using Tropical Storm Claudette (June 2021) as a case study. Results showed that tidal fluctuations had a minimal impact on the saltwater-freshwater interface location, whereas storm surges caused substantial inland movement, with effects lasting for nine months. The steady-state version of the three-dimensional (3D) physical model predicted seawater intrusion across the entire area, and convolutional neural network-based modeling further validated the model results. The 3D physical model was also applied to a smaller area to assess human impact on the saltwater interface due to two groundwater pumping scenarios (± 50% of the baseline pumping rate). Results revealed that a 50% increase in groundwater withdrawals caused seawater to advance ~ 320 m inland, whereas a 50% reduction led to a ~ 270-meter retreat. This study highlights the vulnerability of Alabama’s shallow coastal aquifers to seawater intrusion due to storm surges and human activities, and demonstrates that combining physics-based models with machine learning approaches can improve groundwater predictions, though its accuracy depends on the availability of site-specific data.

Alabama

SURF: An automated method for building nonplanar 3D fault models from earthquake hypocenters

Accurately characterizing 3D fault geometry is vital for improving our understanding of earthquake behavior and informing the development of seismic hazard models. Despite their importance, subsurface fault structures tend to be poorly constrained because of limitations in observational data. Improvements to the seismic networks and earthquake detection algorithms have increased the precision and volume of earthquake catalogs, which help illuminate detailed subsurface fault structure and provide the most direct information available about fault geometries at depth. We present a Python package to automate generating 3D fault geometries directly from hypocentral seismicity patterns. This method begins with clustering events based on their spatial density, identifying coherent patterns. Nearby clusters are then merged based on the similarity of their orientations. We fit nonplanar surfaces using support vector regression to balance surface accuracy with minimal deviations from planarity. The fault models are output as quadrilateral meshes at user‐defined resolution. In the process of generating the 3D fault surfaces, we compute the spatial density of seismicity around the surface and the planarity as quantitative metrics of the model outputs. As a proof of concept, we apply this approach to the San Andreas–Calaveras fault junction region and the 2019 Ridgecrest earthquake sequence, both in California, which contain complex subparallel faults well defined at the Earth’s surface and abundant microseismicity. These case studies demonstrate the method’s ability to model complex fault structures, including long continuous fault surfaces, crossing faults, variably dipping segments, and subparallel faults. We test the method on both standard network catalogs and double‐difference relocated catalogs. We find that our seismicity‐based fault model results align with published 3D models that incorporate additional constraints and interpretations ( Plesch et al. , 2020 ; Aagaard and Hirakawa, 2021 ). This workflow provides a low‐user‐input solution for estimating fault geometries at depth from earthquake catalogs.

California

Event classification, seismicity, and eruption forecasting at Great Sitkin Volcano, Alaska: 1999–2023

The frequency content of volcanogenic seismicity is often used to classify events and their spatial and temporal progression is then used to map subsurface volcanic processes. The progression of volcano-seismic events and associated source processes also plays a critical role in eruption forecasting. Here we develop and evaluate a computerized methodology for characterizing volcano-seismic event types using Frequency Index and Average Peak Frequency. We apply and test this technique at Great Sitkin Volcano, Alaska, classifying over 9000 hypocenters between 1999 and 2023. This 24-year time span covers periods of seismic quiescence, earthquake activity on nearby tectonic (bookshelf) faults, precursory unrest from 2016 to 2021, and the explosive onset in May 2021 of the ongoing effusive eruption. We use the spatial and temporal evolution of classified event types to map the active volcanic and tectonic processes, develop a conceptual model of the subsurface magmatic system, and perform a retrospective analysis of eruption forecasts at Great Sitkin Volcano between 2016 and the present. The classification and progression of hypocenters suggests the subsurface Great Sitkin Volcano magmatic system consists of a mid- to lower- crustal source zone between 10 and 40 km depth and an upper crustal magma storage area between −1 and 10 km depth (hypocenter depth is referenced to sea level and negative depths reflect height above sea level). The earliest precursors occurred in July 2016 and consisted of deep long-period and volcano-tectonic earthquakes at mid-crustal depths suggesting the subsequent unrest and eruption were triggered by a deeper intrusion of magma. This mid-crustal seismic activity was immediately followed by the onset upper-crustal long-period events and volcano-tectonic earthquakes VTs suggesting a strong linkage between the shallow and deeper portions of the magmatic system. The upper crustal area was likely capped by the 1974 lava dome until the magmatic explosion on May 26, 2021.

Alaska

Simulated mean monthly groundwater-transported nitrogen loads in watersheds on the north shore of Long Island Sound, 1993–2022

Elevated nitrogen loads are pervasive in the Long Island Sound, an estuary that receives freshwater and nutrients from both surface-water and groundwater discharge. Surface-water nitrogen loads to the Long Island Sound are relatively well characterized, but less is known about groundwater-transported nitrogen loads. Prior work on the northern shore of Long Island Sound (Connecticut and areas of New York and Rhode Island) suggested that groundwater travel times are relatively short (median less than 2 years) and that decade-long nutrient legacies are not widespread. Because the travel times are short, groundwater flow and nutrient loads likely vary substantially between months. In the current study, the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency’s Long Island Sound Study and the Connecticut Department of Energy and Environmental Protection, developed a set of models to better characterize spatial and temporal patterns of groundwater-transported nitrogen loading from atmospheric deposition, septic systems, and fertilizers within the study area. The models provide an estimate, with uncertainty, of groundwater-transported nitrogen loads in the study area, filling a key gap in the nitrogen budget for Long Island Sound. The models also highlight the spatial and temporal variation in nitrogen loading throughout the study area. The modeling workflow involved four models. (1) A soil-water-balance model was developed by using the Soil-Water-Balance software to simulate groundwater recharge across the study area for water years 2005 through 2022. The simulated mean monthly recharge from the soil-water-balance model was used as input into a groundwater-flow model. (2) The groundwater-flow model was developed by using the MODFLOW 6 software and data for water years 1993 through 2022 and simulates average monthly hydrologic conditions. The groundwater-flow model was calibrated by using the Iterative Ensemble Smoother method within the PEST++ software. The Iterative Ensemble Smoother method generates an ensemble of sets of parameter values, with each set producing reasonable simulated hydrologic parameter values. (3) An ensemble of MODPATH particle-tracking simulations were run to generate particle flow paths and travel times, with each simulation using a different set of the flow model parameters. (4) A nitrogen load model uses the MODPATH simulation outputs to track nitrogen from the land surface through multiple attenuation zones until it discharges into fresh or saline surface water. As with the groundwater-flow model, the nitrogen model simulated average monthly groundwater-transported nitrogen loads for water years 1993 through 2022. One novel aspect of the nitrogen load model is that the nitrogen attenuation parameters were calibrated to observed nitrogen loads. Across the ensemble of simulated nitrogen loads, the median study-area-wide monthly simulated nitrogen loads from the aquifer to Long Island Sound throughout the year ranged from 900 to 18,600 kilograms of nitrogen per day, with a median load of 5,100 kilograms of nitrogen per day. The simulated loads were based on average monthly conditions for water years 1993 through 2022. Loads were highest during the winter and early spring and lowest during the late summer. However, simulated travel times for groundwater and nitrogen loads discharged to Long Island Sound during summer were longer than travel times for groundwater and loads discharged during the winter, indicating that, on average, groundwater discharged during summer traveled along different, and longer, flow paths, than groundwater discharged during winter. This indicates that summer loads would respond more slowly to changes in nitrogen inputs at the water table than winter loads. Over the entire study area, approximately 15 percent of the simulated load is from atmospheric deposition sources, 30 to 40 percent is from fertilizer, and 50 to 60 percent is from septic systems. The final analysis of the study involved simulating the change in groundwater-transported nitrogen load in response to upgrading septic systems or reducing fertilizing inputs to areas of turf grass. Both management interventions reduced the groundwater-transported nitrogen load, and reductions were greater in areas with greater loads from septic systems or turf-grass fertilizers. The delay between management actions and substantial reductions in groundwater-transported nitrogen loads varied seasonally; loads during the late summer months remained elevated longer than the winter loads.

Connecticut, Rhode Island