Hydrogeology and water quality of the Dublin and Midville aquifer systems at Waynesboro, Burke County, Georgia, 2011

Gerard Gonthier

doi:10.3133/sir20135026

Home/Archive/USGS

USGS · sir20135026

Hydrogeology and water quality of the Dublin and Midville aquifer systems at Waynesboro, Burke County, Georgia, 2011

Gerard Gonthier

View original source ↗Read source document ↗Export metadata ↓

Abstract

The hydrogeology and water quality of the Dublin and Midville aquifer systems were characterized in the City of Waynesboro area in Burke County, Georgia, based on geophysical and drillers’ logs, flowmeter surveys, a 24-houraquifer test, and the collection and chemical analysis of water samples in a newly constructed well. At the test site, the Dublin aquifer system consists of interlayered sands and clays between depths of 396 and 691 feet, and the Midville aquifer system consists of a sandy clay layer overlying a sand and gravel layer between depths of 728 and 936 feet. The new well was constructed with three screened intervals in the Dublin aquifer system and four screened intervals in the Midville aquifer system. Wellbore-flowmeter testing at a pumping rate of 1,000 gallons per minute indicated that 52.2 percent of the total flow was from the shallower Dublin aquifer system with the remaining 47.8 percent from the deeper Midville aquifer system. The lower part of the lower Midville aquifer (900 to 930 feet deep), contributed only 0.1 percent of the total flow. Hydraulic properties of the two aquifer systems were estimated using data from two wellbore-flowmeter surveys and a 24-hour aquifer test. Estimated values of transmissivity for the Dublin and Midville aquifer systems were 2,000 and 1,000 feet squared per day, respectively. The upper and lower Dublin aquifers have a combined thickness of about 150 feet and the horizontal hydraulic conductivity of the Dublin aquifer system averages 10 feet per day. The upper Midville aquifer, lower Midville confining unit, and lower Midville aquifer have a combined thickness of about 210 feet, and the horizontal hydraulic conductivity of the Midville aquifer system averages 6 feet per day. Storage coefficient of the Dublin aquifer system, computed using the Theis method on water-level data from one observation well, was estimated to be 0.0003. With a thickness of about 150 feet, the specific storage of the Dublin aquifer system averages about 2×10-6 per foot. Water quality of the Dublin and Midville aquifer systems was characterized during the aquifer test on the basis of water samples collected from composite well flow originating from five depths in the completed production well during the aquifer test. Samples were analyzed for total dissolved solids, specific conductance, pH, alkalinity, and major ions. Water-quality results from composite samples, known flow contribution from individual screens, and a mixing equation were used to calculate water-quality values for sample intervals between sample depths or below the bottom sample depth. With the exception of iron and manganese, constituent concentrations of water from each of the sampled intervals and total flow from the well were within U.S. Environmental Protection Agency primary and secondary drinking-water standards. Water from the bottommost sample interval in the lower part of the lower Midville aquifer (900 to 930 feet) contained manganese and iron concentrations of 59.1 and 1,160 micrograms per liter, respectively, which exceeded secondary drinking-water standards. Because this interval contributed only 0.1 percent of the total flow to the well, water quality of this interval had little effect on the composite well water quality. Two other sample intervals from the Midville aquifer system and the total flow from both aquifer systems contained iron concentrations that slightly exceeded the secondary drinking-water standard of 300 micrograms per liter.

Explore related subjects

Scientific Investigations Report Report

Source-reported bounding extent: 33.072069° to 33.117787° latitude; -82.037295° to -81.991343° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Gerard Gonthier. 2013. Hydrogeology and water quality of the Dublin and Midville aquifer systems at Waynesboro, Burke County, Georgia, 2011. https://doi.org/10.3133/sir20135026

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Karst hydrologic processes in carbonate fensters of the western Great Smoky Mountains, Tennessee, 2017–18

The geology of the Great Smoky Mountains in Tennessee and North Carolina is dominated by metamorphic strata. Along the western extent of the range, however, several carbonate fensters expose the Ordovician Jonesboro Limestone along the western edge of the Great Smoky Fault. The fensters (Cades Cove, Tuckaleechee Cove, and Wear Cove) create opportunities for allogenic recharge at the contact between the surrounding, relatively insoluble, strata and the underlying soluble formations, resulting in the development of karst systems. Karst environments have a high degree of connectivity between surface streams and groundwater systems; thus, karst aquifers are inherently vulnerable to contamination from surface activities. Karst environments also provide a specific environment for sensitive biota. Protection of the unique resources of karst environments requires an understanding of the behavior of karst aquifers, knowledge of karst recharge areas, and the mapping of groundwater flow paths. A study began in 2017 to characterize the hydrologic behavior of the karst systems in Great Smoky Mountains National Park through hydrologic monitoring, dye tracing, and seepage investigations. Hydrologic monitoring equipment was installed at several karst hydrogeologic features: two in-cave sites, two major springs, Abrams Creek in Cades Cove, and a karst depression wetland. Dye tracing was conducted to determine resurgences for the cave systems, to delineate spring recharge areas, and to estimate karst groundwater velocities. Seepage investigations along Abrams Creek helped determine if streams were sinking into the Jonesboro Limestone, either at the contact with insoluble strata or as streams flowed across the carbonate fenster. Study results indicate considerable differences in groundwater behavior between the conduit-dominated flow systems in Tuckaleechee Cove compared to the lower-gradient, colluvium-covered karst systems in Cades Cove. Study results also indicate that contaminants in the area of Bull sink and Whiteoak Sink could be rapidly transported through karst groundwater towards springs in Tuckaleechee Cove. Karst resources in Cades Cove are most likely to be affected by local events or activities taking place within the cove itself or in upper Abrams Creek upstream of the Great Smoky Fault. This study provides information on the vulnerability and uniqueness of the karst systems in the western Great Smoky Mountains, which are characterized by complex geology, high-gradient subterranean streams, deep caves, and carbonate fensters.

Tennessee↗

USGS2026

Analysis of groundwater geochemistry in the Lansing, Michigan, area

Groundwater resources in the Lansing, Michigan, area are protected by a wellhead protection plan, but previous studies have indicated that groundwater in this area may be susceptible to surface contamination. The U.S. Geological Survey, in cooperation with the Lansing Board of Water & Light, analyzed geochemical and aquifer characteristics to assess the potential for contamination of groundwater resources. Recharge age categories were determined from tritium concentrations for some wells, and by using ternary diagrams and principal component analysis for other wells. These age classifications, combined with hydrogeologic and geochemical data, were analyzed by using statistical methods to identify trends that may indicate areas of increased groundwater susceptibility. Wells with modern recharge tended to have higher sodium, chloride, and chloride:bromide ratios than did wells with mixed recharge, suggesting greater surface connectivity and potential influence from anthropogenic sources such as road salt. In contrast, wells in the mixed age category exhibited more stable geochemistry and lower constituent concentrations. Classification and regression tree models identified aquifer geometry—particularly the thickness of the uppermost bedrock unit and presence of confining layers—as key predictors of recharge age and geochemical indicators. The trends identified from these analyses could help to reveal locations in the Lansing area that are among the most susceptible to contamination.

Michigan↗

USGS2026

Evaluating the number of realizations (train-test splits) necessary to ensure robust estimates of conventional hydrothermal resource favorability using Monte Carlo cross-validation, the Great Basin, Western USA

Supervised machine learning approaches used to produce favorability maps in resource assessments commonly partition an input dataset into training and testing subsets (that is, through train-test splits). However, if a single split is not representative of underlying resource conditions, the resulting favorability map may be biased, particularly with sparse or heterogeneous datasets. To mitigate the potential for unrepresentative favorability maps, recent works by U.S. Geological Survey researchers have used Monte Carlo cross-validation to implement a large number ( n) of randomized train-test splits to produce n realizations. The realizations are then aggregated using cell-wise median predictions to produce the resulting final favorability map, recognizing that the median will remove extreme values that might have been estimated from a comparatively few unrepresentative realizations. Theoretically, the median prediction at every cell converges to a single estimate as n approaches infinity, and the question addressed herein is: How many realizations are necessary to get a robust estimate (that is, an estimate unaffected by additional realizations)? Therefore, convergence metrics are described to identify the number of train-test splits and realizations needed to make a reliable map using the data and supervised machine learning workflow for conventional hydrothermal resource assessment of the Great Basin of the Western United States. For this study, robust prediction occurs with n approximately equal to 600 realizations, and smaller ensembles (for example, n is approximately equal to 200 or even 100) may be suitable during preliminary or exploratory analyses. Although the resulting threshold numbers will vary depending on the data and modeling approach used, the convergence metrics proposed and applied herein are applicable to other supervised machine learning studies that use Monte Carlo cross-validation.

California, Idaho, Nevada, Oregon, Utah↗