Updated one-dimensional hydraulic model of the Kootenai River, Idaho: A supplement to Scientific Investigations Report 2005-5110

Christiana R. Czuba; Gary J. Barton

doi:10.3133/sir20115128

Home/Archive/USGS

USGS · sir20115128

Updated one-dimensional hydraulic model of the Kootenai River, Idaho: A supplement to Scientific Investigations Report 2005-5110

Christiana R. Czuba·Gary J. Barton

View original source ↗Export metadata ↓

Abstract

The Kootenai Tribe of Idaho, in cooperation with local, State, Federal, and Canadian agency co-managers and scientists, is assessing the feasibility of a Kootenai River habitat restoration project in Boundary County, Idaho. The restoration project is focused on recovery of the endangered Kootenai River white sturgeon (Acipenser transmontanus) population, and simultaneously targets habitat-based recovery of other native river biota. River restoration is a complex undertaking that requires a thorough understanding of the river and floodplain landscape prior to restoration efforts. To assist in evaluating the feasibility of this endeavor, the U.S. Geological Survey developed an updated one-dimensional hydraulic model of the Kootenai River in Idaho between river miles (RMs) 105.6 and 171.9 to characterize the current hydraulic conditions. A previously calibrated model of the study area, based on channel geometry data collected during 2002 and 2003, was the basis for this updated model. New high-resolution bathymetric surveys conducted in the study reach between RMs 138 and 161.4 provided additional detail of channel morphology. A light detection and ranging (LIDAR) survey was flown in the Kootenai River valley in 2005 between RMs 105.6 and 159.5 to characterize the floodplain topography. Six temporary gaging stations installed in 2006-08 between RMs 154.1 and 161.2, combined with five permanent gaging stations in the study reach, provided discharge and water-surface elevations for model calibration and verification. Measured discharges ranging from about 4,800 to 63,000 cubic feet per second (ft 3 /s) were simulated for calibration events, and calibrated water-surface elevations ranged from about 1,745 to 1,820 feet (ft) throughout the extent of the model. Calibration was considered acceptable when the simulated and measured water-surface elevations at gaging stations differed by less than (+/-)0.15 ft. Model verification consisted of simulating 10 additional events with measured discharges ranging from about 4,900 to 52,000 ft 3 /s, and comparing simulated and measured water-surface elevations at gaging stations. Average water-surface-elevation error in the verification simulations was 0.05 ft, with the error ranging from -1.17 to 0.94 ft over the range of events and gaging stations. Additional verification included a graphical comparison of measured average velocities that range from 1.0 to 6.2 feet per second to simulated velocities at four sites within the study reach for measured discharges ranging from about 7,400 to 46,600 ft 3 /s. The availability of high-resolution bathymetric and LIDAR data, along with the additional gaging stations in the study reach, allowed for more detail to be added to the model and a more thorough calibration, sensitivity, and verification analysis to be conducted. Model resolution and performance is most improved between RMs 140 and 160, which includes the 18.3-mile reach of the Kootenai River white sturgeon critical habitat.

Explore related subjects

Scientific Investigations Report Report

Source-reported bounding extent: 48.61° to 48.7264° latitude; -116.2° to -116.0453° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Christiana R. Czuba, Gary J. Barton. 2011. Updated one-dimensional hydraulic model of the Kootenai River, Idaho: A supplement to Scientific Investigations Report 2005-5110. https://doi.org/10.3133/sir20115128

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Evaluating the number of realizations (train-test splits) necessary to ensure robust estimates of conventional hydrothermal resource favorability using Monte Carlo cross-validation, the Great Basin, Western USA

Supervised machine learning approaches used to produce favorability maps in resource assessments commonly partition an input dataset into training and testing subsets (that is, through train-test splits). However, if a single split is not representative of underlying resource conditions, the resulting favorability map may be biased, particularly with sparse or heterogeneous datasets. To mitigate the potential for unrepresentative favorability maps, recent works by U.S. Geological Survey researchers have used Monte Carlo cross-validation to implement a large number ( n) of randomized train-test splits to produce n realizations. The realizations are then aggregated using cell-wise median predictions to produce the resulting final favorability map, recognizing that the median will remove extreme values that might have been estimated from a comparatively few unrepresentative realizations. Theoretically, the median prediction at every cell converges to a single estimate as n approaches infinity, and the question addressed herein is: How many realizations are necessary to get a robust estimate (that is, an estimate unaffected by additional realizations)? Therefore, convergence metrics are described to identify the number of train-test splits and realizations needed to make a reliable map using the data and supervised machine learning workflow for conventional hydrothermal resource assessment of the Great Basin of the Western United States. For this study, robust prediction occurs with n approximately equal to 600 realizations, and smaller ensembles (for example, n is approximately equal to 200 or even 100) may be suitable during preliminary or exploratory analyses. Although the resulting threshold numbers will vary depending on the data and modeling approach used, the convergence metrics proposed and applied herein are applicable to other supervised machine learning studies that use Monte Carlo cross-validation.

Scientific Investigations Report↗

USGS2026

Groundwater budget for the Portneuf River Basin, southeastern Idaho

The U.S. Geological Survey, in cooperation with the Idaho Department of Water Resources, developed the first groundwater budget for the upper Portneuf River Basin in southeastern Idaho, a tributary of the Snake River. A groundwater budget for the Portneuf River Basin supports water resource and administrative management decisions within the basin and for downstream users of the eastern Snake River Plain aquifer. The analysis quantifies inflows, outflows, and residuals for an aquifer system defined by the Idaho Department of Water Resources under three recent precipitation conditions: an average year (2016), a dry year (2021), and a wet year (2023). The budget was calculated for the basin and for two subbasins delineated by the U.S. Geological Survey streamgage Portneuf River at Topaz, Idaho (13073000): the above Topaz subbasin, which includes the Portneuf-Gem valley, and the below Topaz subbasin, which includes Marsh Valley. Aquifer inflows include mountain-front recharge; areal recharge; recharge from applied water, including recharge from irrigation, canal seepage, and effluent returns; groundwater flow into the basin; and reservoir seepage. Outflows include groundwater pumping for agricultural, municipal, and domestic uses; subsurface outflow through the Portneuf gap; and discharge to streams as base flow. Estimated annual inflows for the full basin ranged from 116,880 acre-feet in 2021 to 154,880 acre-feet in 2023, and outflows ranged from 132,190 acre-feet in 2016 to 158,490 acre-feet in 2023. Basinwide residuals, the change in storage plus uncertainty, were −2,410 acre-feet in 2016, −18,410 acre-feet in 2021, and −3,610 acre-feet in 2023, and each subbasin had a mixture of negative and positive residuals. These basinwide results, interpreted as change in storage plus water-budget uncertainty, indicate minor net losses that increase with dry conditions, consistent with well depth-to-water measurements indicating gradual multi-decadal declines. Patterns in subbasin residuals are driven by irrigation practices and surface-water management; for example, the above Topaz subbasin relies more on groundwater for irrigation, resulting in more negative residuals during dry years. In contrast, the below Topaz subbasin depends more on surface water, producing positive residuals during dry years because of irrigation losses and canal seepage. The analyses for both subbasins indicate decades-long groundwater declines, which agree with the overall negative residuals calculated. The largest sources of uncertainty include climate inputs (precipitation and evapotranspiration) and poorly constrained components such as groundwater inflow and tributary stream infiltration. These findings provide insight into how climatic variables and irrigation practices affect groundwater inflows and outflows within the Portneuf River Basin.

Idaho↗

USGS2026

World minerals outlook—Antimony, copper, graphite, niobium, potash, silicon, silver, and tungsten through 2030

Demand for mineral commodities continues to increase owing to rapid technological advancements and global economic growth. To support this increase in demand, information about current and near-term supplies of these mineral commodities is essential. Such data help evaluate the health and stability of global supply chains and protect against potential supply risks. Current production and production capacity data coupled with information regarding near-term expected changes (such as facility closures, planned expansions, or the completion of new mineral production projects) can provide insight into expected future market developments and expected available supply of mineral commodities. This report within the “World Minerals Outlook” series analyzes data for antimony, copper, natural graphite, niobium, potash, silicon metal, silver, and tungsten—eight mineral commodities listed in the 2025 List of Critical Minerals. World production data from 2019 through 2025, as well as estimated world capacity data from 2023 through 2025 were analyzed. Using these data, near-term (2026–2030) expected world capacities were estimated. For antimony, copper, niobium, silicon metal, silver, and tungsten, modest increases in production capacity of 4 to 10 percent were expected between 2025 and 2030, whereas capacities for natural graphite and potash were expected to increase by about 18 to 20 percent.

Scientific Investigations Report↗