USGS Science⌕ Search
Home/Archive/USGS

USGS · 70198079

The morphology of transverse aeolian ridges on Mars

Paul Geissler·Justin T. Wilgus
View original source ↗Export metadata ↓

Abstract

A preliminary survey of publicly released high resolution digital terrain models (DTMs) produced by the High Resolution Imaging Science Experiment (HiRISE) camera on Mars Reconnaissance Orbiter identified transverse aeolian ridges (TARs) in 154 DTMs in latitudes from 50°S to 40°N. Consistent with previous surveys, the TARs identified in HiRISE DTMs are found at all elevations, irrespective of the regional thermal inertia of the surface. Ten DTMs were selected for measuring the characteristics of the TARs, including maximum height, mean height, mean spacing (wavelength), and the slope of the surface where they are located. We confined our measurements to features that were taller than 1 m and spaced more than 10 m apart. We found a surprisingly wide variability of TAR sizes within each local region (typically 5 km by 25 km), with up to a factor of 7 difference in TAR wavelengths in a single DTM. The TAR wavelengths do not appear to be correlated to latitude or elevation, but the largest TARs in our small survey were found at lower elevations. The tallest TARs we measured were on the flat floor of Moni crater, within Kaiser crater in the southern highlands. These TARs are up to 14 m tall, with a typical wavelength of 120 m. TAR heights are weakly correlated with their wavelengths. The height-to-wavelength ratios for most TARs are far less than 1/2π (the maximum predicted for antidunes), however in two cases the ratio is close to 1/2π, and in one case (in the bend of a channel) the ratio exceeds 1/2π. TAR wavelengths are uncorrelated with surface slope, both on local and regional scales. TAR heights are weakly anti-correlated with local slope. These results help constrain models of TAR formation, particularly a new hypothesis (Geissler, 2014) that suggests that TARs were formed from micron-sized dust that was transported in suspension. The lack of correlation between TAR wavelength and surface slope seems to rule out formation by gravity-driven dust flows such as avalanches or density currents, and suggests that the TARs were instead produced by the Martian winds.

Explore related subjects

Aeolian ResearchArticle

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Paul Geissler, Justin T. Wilgus. 2017. The morphology of transverse aeolian ridges on Mars. https://doi.org/10.1016/j.aeolia.2016.08.008

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

The Sand AbrasioN Device for Aeolian Research (SANDAR): A new experimental device for investigating how wind transport affects sand on Earth and Mars

On Earth and Mars, aeolian transport causes sand grains to become abraded, resulting in mineralogic and textural changes. Understanding how sands evolve, or mature, with transport via experimental studies is important for understanding the origins, geologic history, and cycling of sediments, as well as dust production. Previous experimental works have used a variety of methods to simulate aeolian transport in the laboratory, but practical limitations and similitude concerns have limited such research. Here, we present and validate the Sand AbrasioN Device for Aeolian Research (SANDAR), a modified air mill that uses pressurized air to circulate sand around a small abrasion chamber, simulating the effects of aeolian transport. This device is re-circulating to simulate long-distance transport, and it allows for repeated analyses of well-constrained sediment samples, revealing their evolution over time. It is compatible with the grain sizes (74–500 μm) and grain impact velocities (∼0.6–3.7 m/s) typically expected for natural aeolian environments, and is also adaptable for diverse applications simulating different wind conditions. We show that the SANDAR achieves similitude of kinetic energy with respect to saltating sand on both Earth and Mars. SEM and optical microscope imaging reveal that the SANDAR produces microtextures on the surfaces of sand grains similar to those found with natural aeolian transport, demonstrating that it effectively simulates the mechanical effects of aeolian processes. Thus, the SANDAR is a valid tool for use in experimental research to improve our understanding of sedimentary processes across the Solar System.

Aeolian Research↗
USGS2025

Changes in aeolian saltation cloud properties with wind speed and ripples

Aeolian sediment transport shapes landscapes on Earth and other planetary surfaces, yet key uncertainties remain in how the near-bed saltation cloud responds to changing wind and surface conditions. Leveraging recent advances in image-based particle tracking, we conducted wind tunnel experiments using high-speed imaging and Particle Tracking Velocimetry to quantify sand grain trajectories in saturated saltation clouds over both flat and rippled beds. Our open-source PTV workflow resolved particle motions within millimeters of the bed across a range of wind speeds. Supporting previous results, we find that mean particle velocities do not scale linearly with wind speed; instead, changes in particle velocity distributions—including skewness and kurtosis—emerge as wind strength and sediment flux increase. At higher transport rates, distinctions among saltation, reptation, and creep within the particle distribution become more smoothed, suggesting a continuum spectrum of particle behavior rather than discrete transport modes. Our new dataset of particle trajectories over an active rippled bed shows distinctions in particle speed across the aspects. On ripple stoss slopes, fast saltating grains co-occur with slow creeping particles, while lee slopes are depleted of slower grains, consistent with shadowing effects. These observations support a feedback between ripple morphology and near-bed particle trajectories, with implications for how splash events redistribute sediment momentum. This study contributes new high-resolution empirical data that illuminate how saltation cloud structure evolves with wind forcing and bedform development, advancing our understanding of aeolian sediment transport under complex, dynamic conditions.

Aeolian Research↗
USGS2024

Characterizing variability in geochemistry and mineralogy of western US dust sources

Dust events originate from multiple sources in arid and semi-arid regions, making it difficult to quantify source contributions. Dust geochemical/mineralogical composition, if the sources are sufficiently distinct, can be used to quantify the contributions from different sources. To test the viability of using geochemical and mineralogical measurements to separate dust-emitting sites, we used dust samples collected between 2018 and 2020 from ten National Wind Erosion Research Network (NWERN) sites that are representative of western United States (US) dust sources. Dust composition varied seasonally at many of the sites, but within-site variability was smaller than across-site variability, indicating that the geochemical signatures are robust over time. It was not possible to separate all the sites using commonly applied principal component analysis (PCA) and cluster analysis because of overlap in dust geochemistry. However, a linear discriminant analysis (LDA) successfully separated all sites based on their geochemistry, suggesting that LDA may prove useful for separating dust sources that cannot be separated using PCA or other methods. Further, an LDA based on mineralogical data separated most sites using only a limited number of mineral phases that were readily explained by the local geologic setting. Taken together, the geochemical and mineralogical measurements generated distinct signatures of dust emissions across NWERN sites. If expanded to include a broader range of sites across the western US, a library of geochemical and mineralogical data may serve as a basis to track and quantify dust contributions from these sources.

Aeolian Research↗