USGS Science⌕ Search

USGS · 70156382

An open-water electrical geophysical tool for mapping sub-seafloor heavy placer minerals in 3D and migrating hydrocarbon plumes in 4D

Abstract

A towed-streamer technology has been developed for mapping placer heavy minerals and dispersed hydrocarbon plumes in the open ocean. The approach uses induced polarization (IP), an electrical measurement that encompasses several different surface-reactive capacitive and electrochemical phenomena, and thus is ideally suited for mapping dispersed or disseminated targets. The application is operated at sea by towing active electrical geophysical streamers behind a ship; a wide area can be covered in three dimensions by folding tow-paths over each other in lawn-mower fashion. This technology has already been proven in laboratory and ocean settings to detect IP-reactive titanium- and rare-earth (REE) minerals such as ilmenite and monazite. By extension, minerals that weather and accumulate/concentrate by a similar mechanism, including gold, platinum, and diamonds, may be rapidly detected and mapped indirectly- even when dispersed and covered with thick, inert sediment. IP is also highly reactive to metal structures such as pipelines and cables. Currently, the only means for mapping an oil-spill plume is to park a large ship in the ocean and drop a sampling string over the side, requiring hours of time per sampling point. The samples must then be chemically analyzed, adding additional time and expense. We believe that an extension of the marine IP technology could also apply to rapidly mapping both seafloor- blanket and disseminated hydrocarbon plumes in the open ocean, as hydrocarbon droplets in conductive seawater are topologically equivalent to a metal-plates-and-dielectric capacitor. Because the effective capacitance would be frequency-dependent on droplet size, the approach we advocate holds the potential to not only map, but also to characterize the evolution and degradation of such a plume over time. In areas where offshore oil field development has been practiced for extended periods, making IP measurements from a towed streamer may be useful for locating buried - nd exposed pipelines, as well as pipeline leaks. We believe this technique will be a more cost-effective method than drop-sampling to map and monitor hydrocarbon plumes in open ocean settings. A marine induced polarization system was used successfully to map a 15 km × 45 km swath of the ocean floor off eastern South Africa with 3-meter sampling along 200-meter-separated profiles. The survey detected titanium-bearing sands up to 15 meters below the seafloor. From preliminary laboratory work it is apparent that we can extend this technology to monitor significant environmental problems including anthropogenic and industrial waste washed into sensitive estuaries and sounds during storm-water runoff episodes, and also to map and characterize dispersed oil plumes in the seawater column in three dimensions, as well as movement and dispersal of both over time.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Jefferey C. Wynn, Scott Urquhart, Mike Williamson, John B. Fleming. 2011. An open-water electrical geophysical tool for mapping sub-seafloor heavy placer minerals in 3D and migrating hydrocarbon plumes in 4D. https://pubs.usgs.gov/publication/70156382

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Authoritative knowledge infrastructure for GeoAI: Implications for scientific spatial data providers

Geospatial Artificial Intelligence (GeoAI) increasingly relies on automated analysis of authoritative geospatial data, exposing limitations in data infrastructures originally designed for simple dissemination rather than for knowledge-driven use. From the perspective of scientific spatial data providers, the challenge is enabling GeoAI responsibly while retaining semantic clarity, provenance, reproducibility, and governance. This short paper (i) examines how GeoAI exposed limitations within existing geospatial data infrastructures, and (ii) identifies provider-side requirements for an authoritative knowledge infrastructure. Drawing on GIScience, scientific workflow, and operational AI literature, the paper outlines implications for national mapping organizations that seek to support advanced analytics without jeopardizing scientific rigor or stewardship responsibilities.

Conference Paper↗

Springs of the Catskill Mountains: A conduit flow system in predominantly siliciclastic strata

The Catskill Mountains of New York state are composed of thick sequences of interbedded mudstone, sandstone, and siltstone that are intercalated with thin beds of paludal limestone and calcareous mudstone. Sandstones often contain rip-up clasts of calcareous material at their bases and contain minor amounts of carbonate cement throughout their mass. This minor amount of calcareous material weathers out to produce thin zones of solutional porosity and permeability integrated within perched aquifers that feed perennial hillslope springs. Solutional features are evident within thin carbonate lenses and along fractures in sandstones, occasionally resulting in explorable cave-sized conduits. This study focuses on the behavior of bedrock springs and seeps in the headwaters of the Neversink River basin above the Neversink Reservoir. Bedrock springs are numerous throughout the Catskill Mountains and serve to provide baseflow to the headwater streams that tends to be more persistent during dry times than other baseflow sources. We observed dissolution-influenced conduits within the bedrock, and suffosional conduits within unconsolidated materials. Continuous water temperature at six springs was monitored at hourly intervals from May to October 2022 to investigate the thermal response of groundwater to daily and seasonal changes in air temperature along with event-based meteorological events. Temperature monitoring was augmented at some springs with time-lapse photography to evaluate persistence of flow. The thermal responses of springs to precipitation events were highly variable across sites, with some springs exhibiting flashy responses indicating a strong connection to the surface, while other springs showed muted or no thermal response to events. The seasonal thermal response also varied across sites having lag times of 23-48 days between peak air temperature and peak spring water temperature. The water temperatures and geochemical compositions of these bedrock springs support a conceptual model of multiple residence times, showing both event and seasonal groundwater storage within the conduit flow system that feeds the springs of the Catskill Mountains.

New York↗

Stability changes after weak layer collapse: Insights from an unexpected dataset

While conducting avalanche mitigation or traveling through the backcountry, avalanche professionals sometimes experience a "whumpf": a collapse-mode crack accompanied by surface cracking that does not produce an avalanche. These whumpfs are a clear warning sign of instability in the surrounding terrain. But assessing the collapsed slope itself, if it is steep enough to avalanche, carries much more uncertainty. Can slopes that whumpf and are steep enough to slide still avalanche? The answer to this question supports avalanche mitigators and ski guides in assessing whether to open such slopes. Previous research on collapsed slopes is limited to one study conducted before tests that estimate crack propagation propensity, such as the Propagation Saw Test (PST), were developed. This work showed that weak layer shear strength decreased immediately after collapsing and then increased over time. However, no research has examined crack propagation propensity after a whumpf. Studying propagation propensity is key for assessing how whumpfs immediately affect slope stability. To improve our understanding of changes in propagation propensity following weak layer collapse, we conducted PSTs on a test slope in the hours and days after an unexpected collapse occurred on a layer of surface hoar. Two PSTs at our study site three days prior to this collapse provided an estimate of weak layer propagation propensity. PST cut lengths decreased immediately following the collapse, suggesting that the collapse increased the propagation propensity. However, over the next 4-5 hours, PST cut lengths steadily increased at our site, likely due to ongoing sintering and strengthening in the collapsed weak layer. By the end of day two, we were no longer able to initiate propagation, suggesting substantial stabilization of the weak layer. Our results support prior findings and observations suggesting that slopes may remain capable of producing avalanches immediately after a collapse but likely stabilize over the next day or two. Although this research does not provide answers about precisely when a slope becomes stable after a collapse, it does highlight uncertainties in our understanding and interpretation of the stability of slopes that have whumped.

Montana↗