USGS ScienceSearch

USGS · 70134891

Geologic implications of gas hydrates in the offshore of India: results of the National Gas Hydrate Program Expedition 01

Abstract

The Indian National Gas Hydrate Program Expedition 01 (NGHP-01) is designed to study the occurrence of gas hydrate along the passive continental margin of the Indian Peninsula and in the Andaman convergent margin, with special emphasis on understanding the geologic and geochemical controls on the occurrence of gas hydrate in these two diverse settings. The NGHP-01 expedition established the presence of gas hydrates in the Krishna-Godavari and Mahanadi Basins, and the Andaman Sea. The expedition discovered in the Krishna-Godavari Basin one of the thickest gas hydrate accumulations ever documented, in the Andaman Sea one of the thickest and deepest gas hydrate stability zones in the world, and established the existence of a fully developed gas hydrate petroleum system in all three basins. The primary goal of NGHP-01 was to conduct scientific ocean drilling/coring, logging, and analytical activities to assess the geologic occurrence, regional context, and characteristics of gas hydrate deposits along the continental margins of India. This was done in order to meet the long-term goal of exploiting gas hydrate as a potential energy resource in a cost effective and safe manner. During its 113.5-day voyage, the D/V JOIDES Resolution cored and/or drilled 39 holes at 21 sites (1 site in Kerala-Konkan, 15 sites in Krishna-Godavari, 4 sites in Mahanadi, and 1 site in the Andaman deep offshore area), penetrated more than 9250 m of sedimentary section, and recovered nearly 2850 m of core. Twelve holes were logged with logging-while-drilling (LWD) tools and an additional 13 holes were wireline logged. The science team utilized extensive on-board laboratory facilities to examine and prepare preliminary reports on the physical properties, geochemistry, and sedimentology of all the data collected prior to the end of the expedition. Samples were also analyzed in additional post-expedition shore-based studies conducted in leading laboratories around the world. One of the specific objectives of this expedition was to test gas hydrate formation models and constrain model parameters, especially those that account for the formation of concentrated gas hydrate accumulations. The necessary data for characterizing the occurrence of in situ gas hydrate, such as interstitial water chlorinities, core-derived gas chemistry, physical and sedimentological properties, thermal images of the recovered cores, and downhole measured logging data (LWD and/or conventional wireline log data), were obtained from most of the drill sites established during NGHP-01. Almost all of the drill sites yielded evidence for the occurrence of gas hydrate; however, the inferred in situ concentration of gas hydrate varied substantially from site to site. For the most part, the interpretation of downhole logging data, core thermal images, interstitial water analyses, and pressure core images from the sites drilled during NGHP-01 indicate that the occurrence of concentrated gas hydrate is mostly associated with the presence of fractures in the sediments, and in some limited cases, by coarser grained (mostly sand-rich) sediments.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Timothy S. Collett, Ray Boswell, J. R. Cochran, Pushpendra Kumar, Malcolm Lall, Aninda Mazumdar, Mangipudi Venkata Ramana, Tammisetti Ramprasad, Michael Riedel, Kalachand Sain, Arun Vasant Sathe, Krishna Vishwanath. 2014. Geologic implications of gas hydrates in the offshore of India: results of the National Gas Hydrate Program Expedition 01. https://doi.org/10.1016/j.marpetgeo.2014.07.021

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Terrebonne Basin, Gulf of Mexico gas hydrate resource evaluation and 3-D modeling of basin-scale sedimentation, salt tectonics, and hydrate system evolution since the early Miocene

In assessing methane hydrate as a potential transitional energy source, quantification of in-place volumes of gas is a first step—and yet, global, regional, and even local estimates of gas volumes contained within hydrate are highly variable, including within the extensively-studied Gulf of Mexico (GoM) gas hydrate province. Here, we construct the first 3-D basin and hydrocarbon system model of the Terrebonne Basin (Walker Ridge protraction area, northern GoM) to estimate in-place resources contained as gas within hydrate, as well as to provide the first estimate of in-place resources contained within free gas accumulations in the basin. The resultant model-predicted 3-D distributions (and saturations) of hydrate are consistent with independent seismic interpretation and borehole observations. This study reveals both sedimentation-driven and salt diapir-driven gas hydrate recycling produce elevated hydrate saturations in the basin (“recycling” occurs when relative upward shifts of the gas hydrate stability zone (GHSZ) cause hydrate dissociation, generating buoyant free gas that may reaccumulate as higher-saturation hydrate at the new base of GHSZ). An important finding of this study (particularly given that, globally, the source of methane in marine hydrate systems tends to be poorly understood) is that microbial sources can explain most or all hydrate occurrences in Terrebonne Basin. We calculate that ∼32 × 10 9 m 3 (∼1.1 10 12 ft 3 ) of methane gas is trapped within hydrate accumulations throughout Terrebonne Basin, while nearly 2 × 10 9 m 3 (∼67 × 10 9 ft 3 ) of methane occurs as free gas at high saturations within sandy reservoirs beneath the GHSZ and ∼35 × 10 9 m 3 (∼1.2 × 10 12 ft 3 ) occurs as free gas at low saturations within muddy units beneath the GHSZ. In total, our calibrated 3-D model predicts that nearly 70 × 10 9 m 3 (∼2.5 × 10 12 ft 3 ) of microbial methane is trapped as gas hydrate and free gas in the Terrebonne Basin.

Marine and Petroleum Geology

Mapping the resistivity structure of Walker Ridge 313 in the Gulf of Mexico using the marine CSEM method

A marine controlled source electromagnetic (CSEM) campaign was carried out in the Gulf of Mexico to further develop marine electromagnetic techniques in order to aid the detection and mapping of gas hydrate deposits. Marine CSEM methods are used to obtain an electrical resistivity structure of the subsurface which can indicate the type of substance filling the pore space, such as gas hydrates which are more resistive. Results from the Walker Ridge 313 study (WR 313) are presented in this paper and compared with the Gulf of Mexico Gas Hydrate Joint Industry Project II (JIP2) logging while drilling (LWD) results and available seismic data. The hydrate, known to exist within sheeted sand deposits, is mapped as a resistive region in the two dimensional (2D) CSEM inversion models. This is consistent with the JIP2 LWD resistivity results. CSEM inversions that use seismic horizons provide more realistic results compared to the unconstrained inversions by providing sharp boundaries and architectural control on the location of the resistive and conductive regions in the CSEM model. The seismic horizons include: 1) the base of the gas hydrate stability zone (BGHSZ), 2) the top of salt, and 3) the top and bottom of a fine grained marine mud interval with near vertical hydrate filled fractures, to constrain the CSEM inversion model. The top of salt provides improved location for brines, water saturated salt, and resistive salt. Inversions of the CSEM data map the occurrence of a ‘halo’ of conductive brines above salt. The use of the BGHSZ as a constraint on the inversion helps distinguish between free gas and gas hydrate as well as gas hydrate and water saturated sediments.

Louisiana

Comparison of measured versus modeled TOC in the Tuscaloosa marine shale of Southwestern Mississippi, U.S.A.

This study presents a comparison of measured versus modeled total organic carbon (TOC) in the Upper Cretaceous Tuscaloosa marine shale (TMS) of southwestern Mississippi as a case study to evaluate the effects of mineralogy on the TOC estimated from the ΔlogR method. The ΔlogR method is utilized to calculate TOC, which involves baselining sonic transit time and resistivity log curves in a non-source rock section of the formation. In our application, the well log curves were baselined in the upper TMS, which is described as a non-source rock section, and in the lower TMS above the high resistivity zone (HRZ), which is described as having a higher carbonate content. The ΔlogR calculated TOC values from these two baselining approaches show that the lower baseline results in improved agreement between measured TOC and calculated TOC. This improvement is likely to be due to the lower baseline accounting for the increase in resistivity caused by higher carbonate content, in addition to any presence of TOC. The upper baseline, which has a lower carbonate content, does not account for this resistivity increase. Additionally, sample type appears to affect the comparison of measured and ΔlogR calculated TOC. Most of the samples used in this study are legacy cuttings that were not preserved during storage, exposing the high surface area cuttings to increased rates of oxidation, whereas geophysical logs record the rock properties in situ. To account for this oxidation effect, the difference between the medians of the TMS HRZ TOC core and cuttings values was added to each TOC measurement in this study, resulting in a median measured TOC value that is similar to the median of the lower TMS-baselined ΔlogR calculated TOC value. Overall, this study demonstrates that carbonate content and sample type can affect how well measured and ΔlogR-modeled TOC values compare.

Mississippi