Organic substances in produced and formation water from unconventional natural gas extraction in coal and shale

William H. Orem; Calin A. Tatu; Matthew S. Varonka; Harry E. Lerch; Anne L. Bates; Mark A. Engle; Lynn M. Crosby; Jennifer McIntosh

doi:10.1016/j.coal.2014.01.003

USGS · 70108091

Organic substances in produced and formation water from unconventional natural gas extraction in coal and shale

William H. Orem·Calin A. Tatu·Matthew S. Varonka·Harry E. Lerch·Anne L. Bates·Mark A. Engle·Lynn M. Crosby·Jennifer McIntosh

View original source ↗Export metadata ↓

Abstract

Organic substances in produced and formation water from coalbed methane (CBM) and gas shale plays from across the USA were examined in this study. Disposal of produced waters from gas extraction in coal and shale is an important environmental issue because of the large volumes of water involved and the variable quality of this water. Organic substances in produced water may be environmentally relevant as pollutants, but have been little studied. Results from five CBM plays and two gas shale plays (including the Marcellus Shale) show a myriad of organic chemicals present in the produced and formation water. Organic compound classes present in produced and formation water in CBM plays include: polycyclic aromatic hydrocarbons (PAHs), heterocyclic compounds, alkyl phenols, aromatic amines, alkyl aromatics (alkyl benzenes, alkyl biphenyls), long-chain fatty acids, and aliphatic hydrocarbons. Concentrations of individual compounds range from < 1 to 100 μg/L, but total PAHs (the dominant compound class for most CBM samples) range from 50 to 100 μg/L. Total dissolved organic carbon (TOC) in CBM produced water is generally in the 1–4 mg/L range. Excursions from this general pattern in produced waters from individual wells arise from contaminants introduced by production activities (oils, grease, adhesives, etc.). Organic substances in produced and formation water from gas shale unimpacted by production chemicals have a similar range of compound classes as CBM produced water, and TOC levels of about 8 mg/L. However, produced water from the Marcellus Shale using hydraulic fracturing has TOC levels as high as 5500 mg/L and a range of added organic chemicals including, solvents, biocides, scale inhibitors, and other organic chemicals at levels of 1000 s of μg/L for individual compounds. Levels of these hydraulic fracturing chemicals and TOC decrease rapidly over the first 20 days of water recovery and some level of residual organic contaminants remain up to 250 days after hydraulic fracturing. Although the environmental impacts of the organics in produced water are not well defined, results suggest that care should be exercised in the disposal and release of produced waters containing these organic substances into the environment because of the potential toxicity of many of these substances.

Explore related subjects

International Journal of Coal Geology Article

Source-reported bounding extent: 24.5° to 49.383333° latitude; -124.8° to -66.95° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

William H. Orem, Calin A. Tatu, Matthew S. Varonka, Harry E. Lerch, Anne L. Bates, Mark A. Engle, Lynn M. Crosby, Jennifer McIntosh. 2014. Organic substances in produced and formation water from unconventional natural gas extraction in coal and shale. https://doi.org/10.1016/j.coal.2014.01.003

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2025

Relating systematic molecular and textural properties of graptolite pyrolyzed via gold tube hydrous pyrolysis: Implications for thermal proxies in lower Paleozoic marine shales

A series of gold tube pyrolysis experiments (72 h, 300–550 °C, 50 MPa) conducted on a graptolite-rich lower Paleozoic marine shale generated pyrolysis residues for a comprehensive evaluation of the molecular and structural variability of three types of graptolite periderm. Organic petrology, Raman spectroscopy, and field emission scanning electron microscopy (FE-SEM) with energy dispersive spectroscopy (EDS) were combined to evaluate the thermal evolution process. The three types of graptolite periderm, namely granular, non-granular, and nodular graptolite, were analyzed by Raman spectroscopy wherein point measurements were obtained after the maceral was identified and the location verified by organic petrology. Distinct thermal evolution pathways among non-granular, granular, and nodular graptolite periderms were recorded. The evolution patterns of the Raman parameters, particularly D1 and G bands, highlight the differences in geochemical composition of the graptolite periderm types and the alteration of molecular structure with increasing thermal maturity. Raman parameters D1 (position of the D1 peak), G-FWHM (full width at half maximum of the G peak), and ratios D1-FWHM/G-FWHM (full width at half maximum of the D1 peak ratioed to G-FWHM) and A D1 /A G (ratio of D1 and G peak intensities) showed effectiveness in assessing thermal maturity. Bireflectance with increasing gold tube pyrolysis temperature followed a hierarchy: non-granular > granular > nodular, reflecting different molecular alignment intensities. Qualitative FE-SEM evaluation showed that fine-grained mineral inclusions (primarily Fe-sulfide as determined via EDS) were associated with the graptolite populations, with granular graptolite containing greater amounts of coarser-grained (e.g., ∼300–1400 nm) mineral inclusions relative to non-granular and nodular graptolite, which contain finer-grained (e.g., ∼100–200 nm) inclusions difficult to resolve with optical microscopy. These findings are investigated to highlight the mechanisms that drive organic matter evolution within graptolite during thermal maturation, as well as to explore some of the limitations of using spectroscopic parameters as thermal maturity proxies.

International Journal of Coal Geology↗

USGS2025

Component identification of solid biomass fuels using reflected light microscopy: Interlaboratory study 2

As nations transition toward sustainable energy systems , biomass has become a vital component of global energy portfolios. Derived from organic materials such as wood, agricultural residues, forestry byproducts, and organic waste, biomass is a renewable energy source with significant environmental and economic benefits. Responsible biomass energy production can improve waste management, reduce emissions of greenhouse gases, and mitigate environmental pollution. However, as the diversity of biomass-derived fuels increases, robust quality assessment methods are essential to ensure their efficiency, safety, and minimal environmental impact. Reflected light microscopy (RLM) is one such technique with the potential to complement conventional physico-chemical analyses by enabling a rapid identification of material constituents and impurities. To refine this methodology and evaluate the reproducibility of solid biomass component identification using RLM, an interlaboratory study (ILS) was conducted. The study involved the recognition of 58 components across 45 photomicrographs, with the participation of 65 scientists and students from 25 countries. The participants faced high difficulty identifying some of the marked components, and as a result, the percentage of correct answers ranged from 19.0 % to 98.3 %, with an average correct identification rate of 62.7 %. The most challenging aspects of the identification process included distinguishing between woody and non-woody (agro) biomass, accurately identifying petroleum-derived materials, and differentiating agro biomass from inorganic matter. The results suggest that while RLM is an important tool for characterizing solid biomass, further development of methodology guidelines and training are necessary to enhance its effectiveness. Future research should prioritize preparing detailed, image-rich, microscopic morphological descriptions of biomass fuel components, which could improve the accuracy and reliability of using RLM in biomass fuel characterization.

International Journal of Coal Geology↗

USGS2025

Confocal laser-scanning microscopy (CLSM)-based thermal maturity of Tasmanites and progress in standardization of fluorescence microspectrometry

Evaluation of thermal maturity in vitrinite-free or vitrinite-deficient sediments via fluorescence microspectrometry can provide relevant information related to petroleum exploration and thermal history assessment. However, variation in spectral fluorescence properties of alginite macerals with increasing thermal maturity is largely underexplored. Here, authors of this study have applied confocal laser-scanning microscopy (CLSM) in conjunction with fluorescence microspectrometry to a maturity series of marine Upper Devonian Tasmanites algae from the Ohio Shale (Huron Member) and a single sample from the Marcellus Formation of the Appalachian Basin. Spectral fluorescence properties of Tasmanites were evaluated in relation to orientation, measurement location, and the number of measurements per sample, and were compared to published literature. Emission spectra of Tasmanites from continuous wave laser excitation (405 nm) were acquired from sections perpendicular and parallel to bedding and at different positions within individual Tasmanites bodies. The results showed a progressive red-shift in emission maxima (λ max ) in a large sample sized maturity series ( N = 19), e.g., 493 to 578 nm for the perpendicular section at middle position. Further, blue-shifted apex and mineral-adjacent positions within sections perpendicular to bedding were observed, with the latter being reported here for the first time. While blue-shift at apex positions can be attributed to mechanical deformation-induced reorientation of photoselected fluorophores, the blue-shifted mineral-adjacent positions could result from strain loading and development of a plastic deformation region at the mineral contact zone with Tasmanites . A decrease in standard deviation with increasing number of measured emission maxima is well-observed, and 15 to 20 individual measurements per sample appears sufficient for low standard deviation and coefficient of variance. CLSM-derived thermal maturity parameters indicated that a moderate positive correlation of red/green quotient (Q 650/500 ; R 2 = 0.67) with solid bitumen reflectance (BR o in %) exists. For reproducible results, the determination of λ max and Q 650/500 should be conducted exclusively in the middle position at perpendicular and parallel sections of the polished whole-rock pellets, where the lowest standard deviation in measurement was observed. These results strengthen the suitability and relevance of the CLSM technique in thermal maturity studies of dispersed organic matter (DOM) and contribute to the standardization of fluorescence microspectrometry methods in organic petrology investigation.

Kentucky, Ohio, Virginia, West Virginia↗