USGS Science⌕ Search

USGS · 70046045

A USANS/SANS study of the accessibility of pores in the Barnett Shale to methane and water

Abstract

Shale is an increasingly important source of natural gas in the United States. The gas is held in fine pores that need to be accessed by horizontal drilling and hydrofracturing techniques. Understanding the nature of the pores may provide clues to making gas extraction more efficient. We have investigated two Mississippian Barnett Shale samples, combining small-angle neutron scattering (SANS) and ultrasmall-angle neutron scattering (USANS) to determine the pore size distribution of the shale over the size range 10 nm to 10 μm. By adding deuterated methane (CD 4 ) and, separately, deuterated water (D 2 O) to the shale, we have identified the fraction of pores that are accessible to these compounds over this size range. The total pore size distribution is essentially identical for the two samples. At pore sizes >250 nm, >85% of the pores in both samples are accessible to both CD 4 and D 2 O. However, differences in accessibility to CD 4 are observed in the smaller pore sizes (~25 nm). In one sample, CD 4 penetrated the smallest pores as effectively as it did the larger ones. In the other sample, less than 70% of the smallest pores (<25 nm) were accessible to CD 4 , but they were still largely penetrable by water, suggesting that small-scale heterogeneities in methane accessibility occur in the shale samples even though the total porosity does not differ. An additional study investigating the dependence of scattered intensity with pressure of CD 4 allows for an accurate estimation of the pressure at which the scattered intensity is at a minimum. This study provides information about the composition of the material immediately surrounding the pores. Most of the accessible (open) pores in the 25 nm size range can be associated with either mineral matter or high reflectance organic material. However, a complementary scanning electron microscopy investigation shows that most of the pores in these shale samples are contained in the organic components. The neutron scattering results indicate that the pores are not equally proportioned in the different constituents within the shale. There is some indication from the SANS results that the composition of the pore-containing material varies with pore size; the pore size distribution associated with mineral matter is different from that associated with organic phases.

Explore related subjects

90° N90° S · 180° W ← longitude → 180° E
Source-reported bounding extent: 25.84° to 36.5° latitude; -106.65° to -93.51° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Leslie F. Ruppert, Richard Sakurovs, Tomasz P. Blach, Lilin He, Yuri B. Melnichenko, David F. Mildner, Leo Alcantar-Lopez. 2013-02-12. A USANS/SANS study of the accessibility of pores in the Barnett Shale to methane and water. https://doi.org/10.1021/ef301859s

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Production of secondary microbial methane from a gas hydrate-bearing reservoir at the HYDRATE P1 Production Test Well (PTW-1) on the Alaskan North Slope

Gas hydrate in the Alaskan North Slope (ANS) is believed to contain as much methane as the known conventional gas accumulations in the Prudhoe Bay field. The JOGMEC-DOE-USGS Collaborative Gas Hydrate R&D Project conducted an extended-duration production test from the sub-permafrost, gas-hydrate saturated B1 sand reservoir (unit B) at the Kuparuk State 7-11-12 Site in the Prudhoe Bay Unit of the ANS. Using compositional and stable isotopic data measured on gas produced from well cuttings and pressure cores collected from the HYDRATE 02 Geo Data Well (GDW), we differentiate primary microbial, secondary microbial, and trace thermogenic gas sources. The upper part of the well contained predominantly primary microbial methane from near the surface to the SV6 stratigraphic horizon at 1133 ft (345.3 m) measured depth (MD). Below that, the gas composition transitioned to a mixture of mostly primary and secondary microbial methane to near the base of ice-bearing permafrost at 1968 ft (599.8 m) MD. With greater depth to 3558 ft (1084.5 m) MD, which includes the D1 sand (unit D), the B1 sand (unit B), and the base of gas hydrate stability at 3113 ft (948.8 m) MD, the gas composition was greater than 98% secondary microbial methane with the remainder being oil-associated thermogenic gas migrated from the deep Sadlerochit Formation. The unit B vertical gas profile derived from degassed pressure cores demonstrated that gas dissolved in the clay-rich sediment intervals bounding the B1 sand reservoir was distinct from dissolved and hydrate-caged gases in the sand-rich hydrate-bearing reservoir. The HYDRATE P1 Production Test Well (PTW-1) targeted and successfully extracted gas dissociated from hydrate gas in the B1 sand for 151 days when using an electrical submersible pump to depressurize the reservoir with subsequent depressurization achieved through the use of a jet pump. Gas produced from PTW-1 was mostly indistinguishable from the gas compositional profile measured through the B1 sand and generally distinct from dissolved gas in the bounding clay-rich sediments, confirming that the upper and lower bounding units limited infiltration into the reservoir during production. Isolation of the bounding units from the reservoir contributed to the unexpectedly high ratio of production gas to water observed during the extended-duration gas hydrate production test at PTW-1.

Alaska↗

Depositional environment and diagenetic history of gas hydrate-bearing sediments of the Alaska North Slope (HYDRATE 02 Geo Data Well)

We characterized the lithological, solid-phase geochemical, and rock magnetic properties of sediment cores from subpermafrost strata on the Alaska North Slope collected as part of the U.S. Department of Energy (DOE), the Japan Organization for Metals and Energy Security (JOGMEC), and the U.S. Geological Survey (USGS) Collaborative Gas Hydrate Research and Development (R&D) Project in Alaska. Pressure cores were recovered from the HYDRATE 02 Geo Data Well (GDW) at the Kuparuk State 7-11-12 site through two hydrate-bearing sand reservoirs, the B1 and D1 sands, and their finer-grained bounding sediments. Both the B1 and D1 sands are quartz-rich, chert-bearing, very fine litharenite sands. These submature to immature sands are poorly to moderately sorted and angular with local fine-scale cross-stratification. The B1 sand has larger grains and a lower clay content as compared to the D1 sand. These sands are the upper portions of upward coarsening progradational sequences. The clay- and silt-rich bounding muds exhibit fine-scale wavy and lenticular laminations, suggesting episodic high energy deposition events. Overall, these sediments were deposited in a shoreface to nearshore marine environment during the Paleogene, modulated by changing depositional energy associated with sea level variation. Organic matter δ 13 C and C/N composition of these sediments indicate a source mixture of land plants and freshwater plankton, with possible minor presence of oil within the B1 sand. These sediments contain high and variable total sulfur (TS) content, suggesting porewater conditions influenced by variable salinity over time. Rock magnetic analyses indicate precipitation of greigite in the mud beneath the D1 sand, in the basal C shale overlying the B1 sand, and the mud beneath the B1 sand, likely due to intervals of sulfate limitation during periods of lower Arctic Ocean salinity. Based on pyrite abundance, TS, and δ 34 S-TS composition, the D1 sand and bounding sediments experienced more substantial sulfide precipitation. The unit E basal shale overlying the D1 sand contains a 0.25 m thick pyrite-dominant sand, indicating local bottom water anoxic conditions. X-ray fluorescence scanning and discrete measurements provide additional supporting interpretation of the depositional and diagenetic processes that have occurred at this site and track the relative amount of drilling fluid contamination with barium abundance in the core samples.

Alaska↗

Permeability and compressibility of “seal” sediment overlying the B1 sand gas hydrate reservoir: Hydrate 02 Geo Data Well, Prudhoe Bay unit, Alaska North Slope

An important element in evaluating the viability of extracting methane from a gas hydrate-bearing reservoir is establishing the effectiveness of the overlying bounding sediment as a seal to prevent gas loss, to enable effective depressurization, and to prevent fluid from entering the reservoir during production. This laboratory study presents results for index properties (e.g., grain density, grain size, and liquid limit), compressibility and swelling indices, and permeability measurements on sediment overlying the gas hydrate-bearing reservoir that was the target of the recent JOGMEC-DOE-USGS collaborative gas hydrate production testing project on the Alaska North Slope (ANS). Sediment analyzed in this study was collected during pressure coring operations in the HYDRATE 02 Geo Data Well (GDW). The ∼6.1 m sediment interval recovered in Cores 13P and 14P (878.74–884.88 m measured depth, MD) exhibited heterogeneous sedimentologic characteristics at the centimeter scale, with sediments ranging from clay to thin silty-sand lithologies. Permeability measurements and index-property correlations indicate the interval’s overall in situ vertical permeability ranges from 0.2 to 3.6 microdarcy (μD). Results for compressibility ( C C = 0.255 ± 0.02) and swelling index ( C S = 0.04 ± 0.01) are consistent with estimates based on mineralogy and liquid limit correlations. Based on the measured compressibility, the ∼3 MPa increase in effective stress during the stable phase of depressurization-induced production is anticipated to have imposed 2.43 cm of compaction per meter in the reservoir overburden, reducing permeability by ∼36%. The overburden sediment’s low in situ permeability (3 to 4 orders of magnitude below permeabilities measured in the gas hydrate-bearing part of the B1 sand (unit B)) suggests the B1 sand′s overburden provides an effective seal. Such a seal promotes efficient production by limiting fluid flow into the reservoir during depressurization-induced gas hydrate dissociation.

Alaska↗