USGS Science⌕ Search

USGS · 70029733

Dating young geomorphic surfaces using age of colonizing Douglas fir in southwestern Washington and northwestern Oregon, USA

Abstract

Dating of dynamic, young (<500 years) geomorphic landforms, particularly volcanofluvial features, requires higher precision than is possible with radiocarbon dating. Minimum ages of recently created landforms have long been obtained from tree-ring ages of the oldest trees growing on new surfaces. But to estimate the year of landform creation requires that two time corrections be added to tree ages obtained from increment cores: (1) the time interval between stabilization of the new landform surface and germination of the sampled trees (germination lag time or GLT); and (2) the interval between seedling germination and growth to sampling height, if the trees are not cored at ground level. The sum of these two time intervals is the colonization time gap (CTG). Such time corrections have been needed for more precise dating of terraces and floodplains in lowland river valleys in the Cascade Range, where significant eruption-induced lateral shifting and vertical aggradation of channels can occur over years to decades, and where timing of such geomorphic changes can be critical to emergency planning. Earliest colonizing Douglas fir (Pseudotsuga menziesii) were sampled for tree-ring dating at eight sites on lowland (<750 m a.s.l.), recently formed surfaces of known age near three Cascade volcanoes - Mount Rainier, Mount St. Helens and Mount Hood - in southwestern Washington and northwestern Oregon. Increment cores or stem sections were taken at breast height and, where possible, at ground level from the largest, oldest-looking trees at each study site. At least ten trees were sampled at each site unless the total of early colonizers was less. Results indicate that a correction of four years should be used for GLT and 10 years for CTG if the single largest (and presumed oldest) Douglas fir growing on a surface of unknown age is sampled. This approach would have a potential error of up to 20 years. Error can be reduced by sampling the five largest Douglas fir instead of the single largest. A GLT correction of 5 years should be added to the mean ring-count age of the five largest trees growing on the surface being dated, if the trees are cored at ground level. This correction would have an approximate error of ??5 years. If the trees are cored at about 1.4 m above the round surface (breast height), a CTG correction of 11 years should be added to the mean age of the five sampled trees (with an error of about ??7 years).

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

T.C. Pierson. 2006-10-03. Dating young geomorphic surfaces using age of colonizing Douglas fir in southwestern Washington and northwestern Oregon, USA. https://doi.org/10.1002/esp.1445

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Remote detection of streambank erosion and channel incision using high-resolution, repeat lidar-derived metrics in Raleigh, North Carolina

This study evaluated the use of lidar data to detect streambank erosion and channel incision throughout Raleigh, North Carolina. The study included five components. (1) Generation of lidar-derived rasters, including a digital elevation model of difference that represented channel erosion and positive openness rasters that represented channel incision. (2) Completion of site-based field assessments throughout the study area. (3) Spatial analysis of raster datasets at three spatial scales: erosion patches, channel segments, and subbasins. (4) Comparison of field assessment results with lidar-derived metrics. (5) Pairing of landscape attributes with lidar-derived metrics to evaluate potential causative factors associated with variations in channel incision. Field assessment results indicated 74% of surveyed sites had Bank Erosion Hazard Index ratings ranging from ‘high’ to ‘extreme’ and 77% had ‘high’ or ‘severe’ degrees of channel incision. Select field measures showed agreement with lidar-derived metrics. Lidar-derived erosion patches, ranging in size from 20 to 948 m 2 , were detected in 24.3% of channel segments, and patch density increased with Strahler stream order. Channel segments, ranging from 50 to 150 m, had inconsistent spatial patterns of erosion and incision. Erosion in channel segments increased with Strahler stream order and 36% of channel segments became more incised during the study period. Lidar-derived metrics across subbasins revealed variability of erosion and incision throughout the study area. The assessment of landscape drivers could not explain variability at the channel-segment scale, but subbasins with fewer forests tended to have greater erosion and incision. However, unexplained variability remained, demonstrating the complexity of stream stability in urban watersheds. As lidar datasets become more widespread, pairing remote data with field assessments may be a viable approach to characterize and understand stream geomorphology in urban settings.

North Carolina↗

Deep learning models for mapping surficial geology in selected physiographic regions of New York

Surficial geologic mapping is required for decisions including infrastructure and water-resource development and management. Deep learning, a type of machine learning that uses training data to self-learn and perform tasks, is explored as a tool to help increase efficiency of the labour- and time-intensive mapping process. Deep learning models were trained, and their potential to aid in mapping surficial geology was explored for two physiographic regions in New York: the high-relief Allegheny Plateau and the low-relief Erie-Ontario Lowlands. Key to the development of deep learning models is the availability of highly detailed surficial geologic maps in each of these regions from which the models can learn. Through exploring different groupings of surficial deposits and their corresponding spatial data, deep learning models were iteratively developed to reproduce published mapping for greater than 79% of the training areas, and with similar accuracy in test areas within the same physiographic region. These models were trained using only two inputs: high-resolution lidar data and previously published surficial geologic maps. This straightforward approach is intended to make the methods and models created easily reproducible using widely accessible datasets. This research describes the strengths and limitations of lidar-derived surficial geologic models and how broadly grouping surficial types, characteristics of different physiographic regions, and testing models in physiographic regions outside of their training areas affect model creation and performance. In addition, the models created could be used as a tool for mapping surficial geology in similar physiographic regions, in addition to establishing a framework for creating similar models elsewhere.

New York↗

Regional models for postfire debris-flow likelihood and rainfall thresholds across the western United States

The U.S. Geological Survey (USGS) uses an empirical model developed with logistic regression (the ‘M1’ model) to rapidly assess debris-flow likelihood and to identify quantitative rainfall thresholds for debris flows after wildfire in the western United States. The M1 model was calibrated to a debris-flow inventory from southern California (United States) and has been applied throughout the western United States. Limited spatial coverage in the calibration dataset has motivated evaluation of M1 model accuracy outside the calibration region (e.g., the Sierra Nevada or the eastern Cascade Range, United States). Previous test cases showed that M1 overpredicts debris-flow likelihood and underpredicts rainfall thresholds for some locations (e.g., Arizona, northern California, Colorado, New Mexico, United States). We sought to improve the regional applicability of a debris-flow likelihood model by expanding the debris-flow inventory used for calibration, testing multiple potential models and generating an updated model framework. The updated inventory includes 3788 observations from 67 burned areas paired with short duration rainfall ratios. The updated model framework consists of a modified model structure and sets of coefficients calibrated separately to the entire updated inventory and to subsets of the inventory that intersect three Environmental Protection Agency (EPA) Level 2 ecoregions (Mediterranean California, Upper Gila Mountains and Western Cordillera). Comparisons of predictions from the updated models with observed rainfall and debris-flow activity show that the updated models outperform the M1 model by ~15%–60% and improve the uniformity of predictive performance across the western United States. The updated models also reduce false positive rates relative to M1 and generate rainfall thresholds that are better aligned with relative differences in regional climatology and debris-flow activity.

Arizona, California, Colorado, Idaho, Montana, Nev↗