USGS ScienceSearch

USGS · 70016038

The structure of subtidal currents within and around Lydonia Canyon: Evidence for enhanced cross-shelf fluctuations over the mouth of the canyon

Abstract

Between October 1980 and April 1981, currents were measured within Lydonia Canyon and on the adjacent shelf and slope. The amplitude of the subtidal currents over the shelf and slope ranged between 10 and 30 cm s −1 , but within the canyon, they were typically smaller than 5 cm s −1 . The subtidal currents had well-defined spatial structures over the shelf and the slope and in the middle and outer portions of the canyon. The along-isobath flow over the shelf and slope was unaltered by the canyon. Currents within the canyon and just above it were driven up and down the canyon by the cross-shelf pressure gradient in geostrophic equilibrium with the along-shelf flow. The measurements suggest that the Coriolis force on the cross-canyon flow, turbulent Reynolds stresses, and acceleration of the along-canyon flow balanced the imposed pressure gradient for flow near the rim of Lydonia Canyon. The Coriolis force was not important in the deeper portions of the canyon, where baroclinic adjustments of the density field began to be an important factor in the momentum balance. A simple model indicates that the magnitude of the horizontal turbulent viscosity coefficient for subtidal flow in this narrow canyon is 10 6 to 10 7 cm 2 s −1 . The mixing indicated by the large amplitude of the viscosity coefficient was probably caused by the strong tidal currents present within Lydonia Canyon. On the shelf, along-isobath currents were locally driven by the large-scale component of the wind field; along-shelf currents were equally correlated with local winds and with winds from sites 700 km northeast of Lydonia Canyon. Wind stress was not correlated with currents over the slope in water deeper than 450 m or with currents within the canyon.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

M. Noble, B. Butman. 2012-09-20. The structure of subtidal currents within and around Lydonia Canyon: Evidence for enhanced cross-shelf fluctuations over the mouth of the canyon. https://doi.org/10.1029/jc094ic06p08091

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

Hydrate formation on marine seep bubbles and the implications for water column methane dissolution

Methane released from seafloor seeps contributes to a number of benthic, water column, and atmospheric processes. At seafloor seeps within the methane hydrate stability zone, crystalline gas hydrate shells can form on methane bubbles while the bubbles are still in contact with the seafloor or as the bubbles begin ascending through the water column. These shells reduce methane dissolution rates, allowing hydrate-coated bubbles to deliver methane to shallower depths in the water column than hydrate-free bubbles. Here, we analyze seafloor videos from six deepwater seep sites associated with a diverse range of bubble-release processes involving hydrate formation. Bubbles that grow rapidly are often hydrate-free when released from the seafloor. As bubble growth slows and seafloor residence time increases, a hydrate coating can form on the bubble's gas-water interface, fully coating most bubbles within ∼10 s of the onset of hydrate formation at the seafloor. This finding agrees with water-column observations that most bubbles become hydrate-coated after their initial ∼150 cm of rise, which takes about 10 s. Whether a bubble is coated or not at the seafloor affects how much methane a bubble contains and how quickly that methane dissolves during the bubble's rise through the water column. A simplified model shows that, after rising 150 cm above the seafloor, a bubble that grew a hydrate shell before releasing from the seafloor will have ∼5% more methane than a bubble of initial equal volume that did not grow a hydrate shell after it traveled to the same height.

Journal of Geophysical Research - Oceans

Water-soluble material on aerosols collected within volcanic eruption clouds

In February and March of 1978, filter samplers mounted on an aircraft were used to collect the aerosol fraction of the eruption clouds from three active Guatemalan volcanoes (Fuego, Pacaya, and Santiaguito). The samples were collected on Teflon (Fluoropore) filters with a nominal pore diameter of 0.5μm. The mass of air sampled by the filters ranged from 0.15 to 6.6 kg. The particulate material collected consisted of fragments of angular silicate ash and droplets of what is interpreted as dilute H 2 SO 4 and HCl. After collection of the samples, each filter was rinsed with 60 ml of distilled-deionized water. Splits of each extract were centrifuged to remove particles greater than or equal to 0.1 μm in diameter, acidified, and analyzed for B, Ba, Be, Ca, Cd, Co, Cu, Fe, Li, Mg, Mn, Mo, Na, Pb, Si, Sr, V, and Zn by inductively coupled plasma—optical emission spectroscopy. Separate splits were analyzed for F and Cl by specific-ion-electrode methods and for U by a fission track technique. The elements dissolved in the aqueous extracts represent components of water-soluble material either formed directly in the eruption cloud or derived from interaction of ash particles and aerosol components of the plume. Calculations of enrichment factors, based upon concentration ratios, showed the elements most enriched in the extracts relative to bulk ash composition were Cd, Cu, V, F, Cl, Zn, and Pb. These elements represent a subset (with the addition of Cl and F) of elements previously reported enriched in atmospheric aerosols in remote regions as well as in volcanic areas. This suggests that some of the enriched elements were widely dispersed as volatile halides emitted from a volcanic source.

Journal of Geophysical Research - Oceans

Sea ice melting in the marginal ice zone

The heat and salt flux boundary conditions together with the freezing curve relationship are a necessary component of any ice-sea water thermodynamic model. A neutral two-layer oceanic planetary boundary layer model that incorporates these boundary conditions gives the following results: The interfacial salinity is within 10% of the far-field salinity for conditions commonly encountered in the MIZ and depends only on the turbulent Lewis number and the far-field temperature and salinity. The predicted melt rates agree with the limited field observations, of the order of 1 m day −1 . The Obukov lengths, determined from the predicted interface conditions and melt rates, are generally much greater than the Ekman layer thicknesses; hence, the surface buoyancy flux has little effect on the turbulence in the planetary boundary layer.

Journal of Geophysical Research - Oceans