USGS Science⌕ Search
Home/Archive/USGS

USGS · 70012260

Wave energy saturation on a natural beach of variable slope

A. H. Sallenger·R.A. Holman
View original source ↗Export metadata ↓

Abstract

Time series of flow were measured across the inner surf zone during a storm. These data were used to quantify the dependence of wave height (transformed from measured flow) and velocity on local slope and depth. Similar to previous studies, as incident waves broke and propagated into the surf zone, wave energy became saturated, and wave height was strongly dependent on depth. However, the ratio of rms wave height to local depth (γ rms ) was found not to be constant but to vary between 0.29 and 0.55; γ rms increased with local slope and was independent of deepwater wave steepness. Thus the surf zone similarity parameter (the ratio of slope to the square root of steepness) did not adequately parameterize γ rms .

Explore related subjects

Journal of Geophysical Research - OceansArticle

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

A. H. Sallenger, R.A. Holman. 2012-09-20. Wave energy saturation on a natural beach of variable slope. https://doi.org/10.1029/jc090ic06p11939

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2021

Hydrate formation on marine seep bubbles and the implications for water column methane dissolution

Methane released from seafloor seeps contributes to a number of benthic, water column, and atmospheric processes. At seafloor seeps within the methane hydrate stability zone, crystalline gas hydrate shells can form on methane bubbles while the bubbles are still in contact with the seafloor or as the bubbles begin ascending through the water column. These shells reduce methane dissolution rates, allowing hydrate-coated bubbles to deliver methane to shallower depths in the water column than hydrate-free bubbles. Here, we analyze seafloor videos from six deepwater seep sites associated with a diverse range of bubble-release processes involving hydrate formation. Bubbles that grow rapidly are often hydrate-free when released from the seafloor. As bubble growth slows and seafloor residence time increases, a hydrate coating can form on the bubble's gas-water interface, fully coating most bubbles within ∼10 s of the onset of hydrate formation at the seafloor. This finding agrees with water-column observations that most bubbles become hydrate-coated after their initial ∼150 cm of rise, which takes about 10 s. Whether a bubble is coated or not at the seafloor affects how much methane a bubble contains and how quickly that methane dissolves during the bubble's rise through the water column. A simplified model shows that, after rising 150 cm above the seafloor, a bubble that grew a hydrate shell before releasing from the seafloor will have ∼5% more methane than a bubble of initial equal volume that did not grow a hydrate shell after it traveled to the same height.

Journal of Geophysical Research - Oceans↗
USGS2012

Water-soluble material on aerosols collected within volcanic eruption clouds

In February and March of 1978, filter samplers mounted on an aircraft were used to collect the aerosol fraction of the eruption clouds from three active Guatemalan volcanoes (Fuego, Pacaya, and Santiaguito). The samples were collected on Teflon (Fluoropore) filters with a nominal pore diameter of 0.5μm. The mass of air sampled by the filters ranged from 0.15 to 6.6 kg. The particulate material collected consisted of fragments of angular silicate ash and droplets of what is interpreted as dilute H 2 SO 4 and HCl. After collection of the samples, each filter was rinsed with 60 ml of distilled-deionized water. Splits of each extract were centrifuged to remove particles greater than or equal to 0.1 μm in diameter, acidified, and analyzed for B, Ba, Be, Ca, Cd, Co, Cu, Fe, Li, Mg, Mn, Mo, Na, Pb, Si, Sr, V, and Zn by inductively coupled plasma—optical emission spectroscopy. Separate splits were analyzed for F and Cl by specific-ion-electrode methods and for U by a fission track technique. The elements dissolved in the aqueous extracts represent components of water-soluble material either formed directly in the eruption cloud or derived from interaction of ash particles and aerosol components of the plume. Calculations of enrichment factors, based upon concentration ratios, showed the elements most enriched in the extracts relative to bulk ash composition were Cd, Cu, V, F, Cl, Zn, and Pb. These elements represent a subset (with the addition of Cl and F) of elements previously reported enriched in atmospheric aerosols in remote regions as well as in volcanic areas. This suggests that some of the enriched elements were widely dispersed as volatile halides emitted from a volcanic source.

Journal of Geophysical Research - Oceans↗
USGS2012

Sea ice melting in the marginal ice zone

The heat and salt flux boundary conditions together with the freezing curve relationship are a necessary component of any ice-sea water thermodynamic model. A neutral two-layer oceanic planetary boundary layer model that incorporates these boundary conditions gives the following results: The interfacial salinity is within 10% of the far-field salinity for conditions commonly encountered in the MIZ and depends only on the turbulent Lewis number and the far-field temperature and salinity. The predicted melt rates agree with the limited field observations, of the order of 1 m day −1 . The Obukov lengths, determined from the predicted interface conditions and melt rates, are generally much greater than the Ekman layer thicknesses; hence, the surface buoyancy flux has little effect on the turbulence in the planetary boundary layer.

Journal of Geophysical Research - Oceans↗