Temperature dependence of decay time and intensity of alpha pulses in pure and thallium-activated cesium iodide

F. E. Senftle; P. Martinez; V. P. Alekna

doi:10.1063/1.1717979

Home/Archive/USGS

USGS · 70010571

Temperature dependence of decay time and intensity of alpha pulses in pure and thallium-activated cesium iodide

F. E. Senftle·P. Martinez·V. P. Alekna

View original source ↗Export metadata ↓

Abstract

The intensity and decay time of Po 210 alpha particle scintillations produced in pure and thallium‐activated cesium iodide have been measured with a fast electronic system as a function of temperature down to 77°K. Three modes of decay due to alpha excitation have been observed for CsI(Tl), and two for CsI. Other than the 7‐ and 0.55‐μsec modes (at room temperature) reported in the literature for CsI(Tl), an additional temperature‐independent mode of about 1.3 μsec has been detected between 77 and 150°K. In CsI a fast temperature‐dependent mode of decay (≈100 nsec) was observed between 100–200°K in addition to the known principal mode.

Explore related subjects

Review of Scientific Instruments Article

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

F. E. Senftle, P. Martinez, V. P. Alekna. 1962. Temperature dependence of decay time and intensity of alpha pulses in pure and thallium-activated cesium iodide. https://doi.org/10.1063/1.1717979

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2012

Note: Rotaphone, a new self-calibrated six-degree-of-freedom seismic sensor

We have developed and tested (calibration, linearity, and cross-axis errors) a new six-degree-of-freedom mechanical seismic sensor for collocated measurements of three translational and three rotational ground motion velocity components. The device consists of standard geophones arranged in parallel pairs to detect spatial gradients. The instrument operates in a high-frequency range (above the natural frequency of the geophones, 4.5 Hz). Its theoretical sensitivity limit in this range is 10(-9) m/s in ground velocity and 10(-9) rad/s in rotation rate. Small size and weight, and easy installation and maintenance make the instrument useful for local-earthquake recording and seismic prospecting.

Review of Scientific Instruments↗

USGS2007

Synchrotron x-ray spectroscopy of EuHN O3 aqueous solutions at high temperatures and pressures and Nb-bearing silicate melt phases coexisting with hydrothermal fluids using a modified hydrothermal diamond anvil cell and rail assembly

A modified hydrothermal diamond anvil cell (HDAC) rail assembly has been constructed for making synchrotron x-ray absorption spectroscopy, x-ray fluorescence, and x-ray mapping measurements on fluids or solid phases in contact with hydrothermal fluids up to ???900??C and 700 MPa. The diamond anvils of the HDAC are modified by laser milling grooves or holes, for the reduction of attenuation of incident and fluorescent x rays and sample cavities. The modified HDAC rail assembly has flexibility in design for measurement of light elements at low concentrations or heavy elements at trace levels in the sample and the capability to probe minute individual phases of a multiphase fluid-based system using focused x-ray microbeam. The supporting rail allows for uniform translation of the HDAC, rotation and tilt stages, and a focusing mirror, which is used to illuminate the sample for visual observation using a microscope, relative to the direction of the incident x-ray beam. A structure study of Eu(III) aqua ion behavior in high-temperature aqueous solutions and a study of Nb partitioning and coordination in a silicate melt in contact with a hydrothermal fluid are described as applications utilizing the modified HDAC rail assembly. ?? 2007 American Institute of Physics.

Review of Scientific Instruments↗

USGS2006

Estimating thermal diffusivity and specific heat from needle probe thermal conductivity data

Thermal diffusivity and specific heat can be estimated from thermal conductivity measurements made using a standard needle probe and a suitably high data acquisition rate. Thermal properties are calculated from the measured temperature change in a sample subjected to heating by a needle probe. Accurate thermal conductivity measurements are obtained from a linear fit to many tens or hundreds of temperature change data points. In contrast, thermal diffusivity calculations require a nonlinear fit to the measured temperature change occurring in the first few tenths of a second of the measurement, resulting in a lower accuracy than that obtained for thermal conductivity. Specific heat is calculated from the ratio of thermal conductivity to diffusivity, and thus can have an uncertainty no better than that of the diffusivity estimate. Our thermal conductivity measurements of ice Ih and of tetrahydrofuran (THF) hydrate, made using a 1.6 mm outer diameter needle probe and a data acquisition rate of 18.2 pointss, agree with published results. Our thermal diffusivity and specific heat results reproduce published results within 25% for ice Ih and 3% for THF hydrate. ?? 2006 American Institute of Physics.

Review of Scientific Instruments↗