USGS ScienceSearch

Geology topics

Research about San Francisco, California

Source-linked reports with geographic coverage including San Francisco, California.

At least 91 records · Page 5Linked to original sources

Site amplification at five locations in San Francisco, California: A comparison of S waves, codas, and microtremors

We compare microtremor data to weak-motion S -wave and coda recordings at sites in San Francisco in order to clarify the range of applicability of microtremor data to ground-motion prediction. We also compare S -wave results to coda results. For each type of data, we compute spectral ratios of motions from two soil/rock station pairs and from an uphole/downhole pair in the Marina district. We compute horizontal/vertical ratios (Nakamura's method) at a soil site, a rock site, and the surface and borehole instruments. In the station-pair analyses, microtremor data show amplifications at the same fundamental frequency as S waves, but the frequencies of other peaks do not agree. The amplification at frequencies higher than 2 Hz is greater in the microtremor data. Station-pair ratios of coda data generally show spectral peaks occurring at the same frequencies, but with levels varying from one to four times the amplification from S -wave ratios. Nakamura's method of analyzing microtremors agrees better with S -wave station-pair results than the microtremor station-pair method over a limited frequency band that varies from station to station.

California

Choosing optimum station configurations for summarizing water quality characteristics, in 1994 Annual Report, San Francisco Estuary Regional Monitoring Program for Trace Substances: San Francisco Estuary Institute

One of the central problems in regional monitoring is choosing a station array that accurately reflects the distribution of values for the entire region of interest. For time-consuming or expensive measurements, an additional goal is to make the number of sampling locations and times as small as possible. These problems are probably most difficult in estuaries because of the relatively large variability on many different spatial and temporal scales. This high variability often means that comprehensive historical data are not available for accurately assessing sparser sampling efforts. It also implies that a higher frequency of sampling in space and time is required compared to other water bodies. In this report, we focus on selection of an “optimum” station configuration for the channel of San Francisco Bay for vertical profiling of water quality. Our analysis is based on the monthly cruises conducted by the USGS under the auspices of the Regional Monitoring Program for Trace Substances (Caffrey et al. 1994; SFEI 1994). The underlying rationale for undertaking the analysis is that the distribution of trace substances is structured, at least in part, by the same forces acting on water quality parameters. This must be true to some extent, as trace substance concentrations are partially dependent on water quality characteristics such as salinity. On the other hand, the quantitative importance of these parameters in accounting for overall variability in individual trace substances is unknown. Furthermore, trace substances have their own unique sources, and these sources may dominate their distribution.

California

Isohaline position as a habitat indicator for estuarine populations

Populations of native and introduced aquatic organisms in the San Francisco Bay/Sacramento-San Joaquin Delta Estuary ("Bay/Delta") have undergone significant declines over the past two decades. Decreased river inflow due to drought and increased freshwater diversion have contributed to the decline of at least some populations. Effective management of the estuary's biological resources requires a sensitive indicator of the response to freshwater inflow that has ecological significance, can be measured accurately and easily, and could be used as a "policy" variable to set standards for managing freshwater inflow. Positioning of the 2% (grams of salt per kilogram of seawater) bottom salinity value along the axis of the estuary was examined for this purpose. The 2% bottom salinity position (denoted by X 2 ) has simple and significant statistical relationships with annual measures of many estuarine resources, including the supply of phytoplankton and phytoplankton-derived detritus from local production and river loading; benthic macroinvertebrates (molluscs); mysids and shrimp; larval fish survival; and the abundance of planktivorous, piscivorous, and bottom-foraging fish. The actual mechanisms are understood for only a few of these populations. X 2 also satisfies other recognized requirements for a habitat indicator and probably can be measured with greater accuracy and precision than alternative habitat indicators such as net freshwater inflow into the estuary. The 2% value may not have special ecological significance for other estuaries (in the Bay/Delta, it marks the locations of an estuarine turbidity maximum and peaks in the abundance of several estuarine organisms), but the concept of using near-bottom isohaline position as a habitat indicator should be widely applicable. Although X 2 is a sensitive index of the estuarine community's response to net freshwater inflow, other hydraulic features of the estuary also determine population abundances and resource levels. In particular, diversion of water for export from or consumption within the estuary can have a direct effect on population abundance independent of its effect on X 2 . The need to consider diversion, in addition to X 2 , for managing certain estuarine resources is illustrated using striped bass survival as an example. The striped bass survival data were also used to illustrate a related important point: incorporating additional explanatory variables may decrease the prediction error for a population or process, but it can increase the uncertainty in parameter estimates and management strategies based on these estimates. Even in cases where the uncertainty is currently too large to guide management decisions, an uncertainty analysis can identify the most practical direction for future data acquisition.

California

Geologic map and structure sections of the Clear Lake Volcanics, Northern California

The Clear Lake Volcanics are located in the California Coast Ranges about 150 km north of San Francisco. This Quaternary volcanic field has erupted intermittently since 2.1 million years ago. This volcanic field is considered a high-threat volcanic system (Ewert and others, 2005) The adjacent Geysers geothermal field, largest power-producing geothermal field in the world, is powered by the magmatic heat source for the volcanic field. This report consists of three sheets that include the geologic map, one table, two figures, three cross sections, description of map units, charts of standard and diagrammatic correlation of map units, and references. This map supersedes U.S. Geological Survey Open-File Report 76-751. Descriptions of map units are grouped by geographic area. Summaries of the evolution, chemistry, structure, and tectonic setting of the Clear Lake Volcanics are given in Hearn and others (1981) and Donnelly-Nolan and others (1981). The geology of parts of the area underlain by the Cache Formation is based on mapping by Rymer (1981); the geology of parts of the areas underlain by the Sonoma Volcanics, Franciscan assemblage, and Great Valley sequence is based on mapping by McLaughlin (1978). Volcanic compositional map units are basalt, basaltic andesite, andesite, dacite, rhyodacite, and rhyolite, based on SiO2 content. Included in this report are maps showing the distribution of volcanic rocks through time and a chart showing erupted volumes of different lava types through time. A table gives petrographic data for each map unit by mineral type, abundance, and size. Most ages are potassium-argon (K/Ar) ages determined for whole-rock samples and mineral separates by Donnelly-Nolan and others (1981), unless otherwise noted. A few ages are carbon-14 ages or were estimated from geologic relationships. Magnetic polarities are from Mankinen and others (1978; 1981) or were determined in the field by B.C. Hearn, Jr., using a portable fluxgate magnetometer. Thickness for most units is estimated from topographic relief except where drill-hole data were available.

California

Hillside materials and slopes of the San Francisco Bay region, California

This report describes the various bedrock and soil materials and slope gradients that constitute hillsides in the San Francisco Bay region. Distribution of materials and slopes is shown on 1:125,000-scale maps of the region. Approximately 360 materials units are described by bedrock composition, physical properties of bedrock (rock hardness, spacing of fractures and partings, and bed thickness), texture of the soil cover, expansivity, permeability, and stratigraphic thickness. Materials map units are based on compilations of geologic mapping of the region; descriptions are based on systematic field observations, free-swell tests for expansivity, examination of aerial photographs, and the literature.

California

1994 Annual report: San Francisco Estuary regional monitoring program for trace substances

This is the second Annual Report of the Regional Monitoring Program for Trace Substances (RMP). It describes concentrations of pollutants in water, sediment, and tissue samples of oysters, mussels, and clams at 15 to 24 sampling locations for three discrete sampling events - during the wet season in February, in April during a period of declining Delta outflows, and during the dry season in August. The sampling stations are located throughout the Estuary and at the major tributaries including the mouths of the Guadalupe River and Coyote Creek in the extreme southern portions of the Estuary to the confluence of the Sacramento and San Joaquin Rivers (Figure 1). In 1994, water samples were also taken at two upstream locations at Rio Vista (Sacramento River) and Manteca (San Joaquin River) to determine river contaminant concentrations during a six-week period in spring.

California

Ionic strength and DOC determinations from various freshwater sources to the San Francisco Bay

An exact estimation of dissolved organic carbon (DOC) within the salinity gradient of zinc and copper metals is significant in understanding the limit to which DOC could influence metal speciation. A low-temperature persulfate/oxygen/ultraviolet wet oxidation procedure was utilized for analyzing DOC samples adapted for ionic strength from major freshwater sources of the northern and southern regions of San Francisco Bay. The ionic strength of samples was modified with a chemically defined seawater medium up to 0.7M. Based on the results, a minimum effect of ionic strength on oxidation proficiency for DOC sources to the Bay over an ionic strength gradient of 0.0 to 0.7 M was observed. There was no major impacts of ionic strength on two Suwanee River fulvic acids. In general, the noted effects associated with ionic strength were smaller than the variances seen in the aquatic environment between high- and low-temperature methods.

California

Seismic evidence for a lower-crustal detachment beneath San Francisco Bay, California

Results from the San Francisco Bay area seismic imaging experiment (BASIX) reveal the presence of a prominent lower crustal reflector at a depth of ∼15 kilometers beneath San Francisco and San Pablo bays. Velocity analyses indicate that this reflector marks the base of Franciscan assemblage rocks and the top of a mafic lower crust. Because this compositional contrast would imply a strong rheological contrast, this interface may correspond to a lower crustal detachment surface. If so, it may represent a subhorizontal segment of the North America and Pacific plate boundary proposed by earlier thermo-mechanical and geological models.

California

Seismic velocities and geologic logs from boreholes at three downhole arrays in San Francisco, California

The Loma Prieta earthquake of October 17, 1989 (1704 PST), has reinforced observations made by Wood and others (1908) after the 1906 San Francisco earthquake, that poor ground conditions (soft soil) increase the likelihood of shaking damage to structures. Since 1908 many studies (for example Borcherdt, 1970, Borcherdt and Gibbs, 1976, Borcherdt and Glassmoyer, 1992) have shown that soft soils amplify seismic waves at frequencies that can be damaging to structures. Damage in the City of San Francisco from the Loma Prieta earthquake was concentrated in the Marina District, the Embarcadero, and the China Basin areas. Each of these areas, to some degree, is underlain by soft soil deposits. These concentrations of damage raise important questions regarding the amplification effects of such deposits at damaging levels of motion. Unfortunately, no strong-motion recordings were obtained in these areas during the Loma Prieta earthquake and only a limited number (< 10) have been obtained on other soft soil sites in the United States. Consequently, important questions exist regarding the response of such deposits during damaging earthquakes, especially questions regarding the nonlinear soil response. Towards developing a data set to address these important questions, borehole strong-motion arrays have been installed at three locations. These arrays consist of groups of wide-dynamic-range pore-pressure transducers and three-component accelerometers, the outputs of which are recorded digitally. The arrays are designed to provide an integrated set of data on ground shaking, liquifaction-induced ground failure, and structural response. This report describes the detailed geologic, seismic, and material-property determinations derived at each of these sites.

California

A survey of molecular marker compounds in sediments of San Francisco Bay, California

An areal survey of surficial sediments in San Francisco Bay has been conducted to evaluate the presence of extractable organic compounds. Molecular marker compounds studied include hydrocarbons (PAH's), chlorinated pesticides, and other organic compounds that provide information on sources of organic input into the Bay. Fairly uniform source profiles are seen throughout the Bay. Biomarker profiles contain mature constituents indicating anthropogenic influences and extensive sediment reworking. The dominant input signatures in San Francisco Bay sediment are those of anthropogenic PAH's from combustion and other sources, and long chain n-alkanes and n-aldehydes from terrigenous vascular plants. A comparison of the sums of the combustion PAH's and the terrigenous n-alkanes shows that an anthropogenic influence is dominant in the most urban parts of the Bay close to shore, and in mid-Bay channel areas, and a terrigenous signature is dominant nearshore in San Pablo Bay and at the southernmost station in South Bay.

California

San Francisco Bay/delta regional monitoring program plankton and water quality pilot study, 1993, in 1993 Annual Report, San Francisco Estuary Regional Monitoring Program for Trace Substances: San Francisco Estuary Institute

The pilot program described here is motivated by a fundamental principle of the Regional Monitoring Strategy, namely &ldquo;...the development of data that will provide information on status and trends in the Estuary.&rdquo; As pointed out in the Strategy, knowledge of status and trends serves two primary purposes: (1) to become aware of or anticipate deleterious conditions in the Estuary, and (2) to assess the effectiveness of management actions. This program addresses these two purposes by focusing on aquatic resources, one of the five key management issues identified by the Comprehensive Conservation and Management Plan and central to the Regional Monitoring Strategy. It also bears on at least two of the other management issues - pollutants and water use. A regional monitoring program must cover many types of resources, including pelagic and benthic channel habitat, shoal habitat, wetlands, river channels, sloughs, and small bays and harbors. This particular program centers on the pelagic channel habitat. However, because of the intimate connection between channel habitat and many or most of these other habitats, channel measurements reflect to some extent the status of and trends in other resource types as well. A primary aim of this program is to provide a high-resolution description of critical aspects of habitat quality, which can be used along with other information (1) to determine the suitability of habitat for aquatic resources; (2) to monitor responsiveness of the habitat to freshwater flow variability; and (3) to provide a context for understanding pollutant distributions. In a single transect, measurements are made throughout the water column at up to 37 stations to define physical (salinity, temperature, suspended particulate matter, and light penetration), chemical (dissolved oxygen) and biological (chlorophyll a ) characteristics that influence both chemical and biological reactions. A second aim of the program is to investigate planktonic indicators of ecosystem structure and function. Phytoplankton production is the major single source of energy for the San Francisco Bay food web. Our measurements of chlorophyll and light penetration can be used to provide an estimate of this production, and therefore the availability of food for organisms at higher trophic levels. Phytoplankton community composition at the species level, which can be a sensitive indicator of habitat change, is also a standard component of this program. Community composition data enable detection of species known to be responsible for harmful or nuisance algal blooms. In 1993, two other indicators were also evaluated, photosynthetic parameters and water column respiration . Photosynthetic parameters partially characterize the physiological state of the phytoplankton and may provide indirect evidence of nutrient deficiency or the effects of pollutants. Water column respiration serves as a simple integrated measure of organic matter metabolism by the plankton, including bacteria, phytoplankton, and microzooplankton. It therefore reflects the total supply of organic matter, whether from photosynthesis, tidal marsh efflux, point sources, or upstream in the Delta. These biological indicators therefore contain much information about the flow of energy into the food web.

California

Response of a 42-storey steel-frame building to the Ms = 7.1 Loma Prieta earthquake

A set of 14 acceleration records was obtained from a 42-storey steel-frame building, the Chevron Building, in San Francisco during the M s = 7.1 "> M s = 7.1 Loma Prieta earthquake of 17 October 1989. Data were analysed using a system identification method based on the discretetime linear filtering, and the least-squares estimation techniques. The results show that the response of the building is dominated by two modes: a translational mode in the weaker (southwest-northeast) principal direction of the building at 0.16 Hz with 5% damping, and a translational-torsional mode along the east-west diagonal of the building's cross-section at 0.20 Hz with 7% damping. There are significant contributions from higher modes at 0.54 Hz, 0.62 Hz, 1.02 Hz and 1.09 Hz. All the modes incorporate some torsion, but the amplitudes of torsional components are small, about 10% of translational amplitudes. Soil-structure interaction influences the vibrations near 1.0 Hz. The contribution of soil-structure interaction to the peak displacements of the building is significant, particularly at lower floors.

California

Organic carbon sources and sinks in San Francisco Bay: variability induced by river flow

Sources and sinks of organic carbon for San Francisco Bay (California, USA) were estimated for 1980. Sources for the southern reach were dominated by phytoplankton and benthic microalgal production. River loading of organic matter was an additional important factor in the northern reach. Tidal marsh export and point sources played a secondary role. Autochthonous production in San Francisco Bay appears to be less than the mean for temperate-zone estuaries, primarily because turbidity limits microalgal production and the development of seagrass beds. Exchange between the Bay and Pacific Ocean plays an unknown but potentially important role in the organic carbon balance. Interannual variability in the organic carbon supply was assessed for Suisun Bay, a northern reach subembayment that provides habitat for important fish species (delta smelt Hypomesus transpacificus and larval striped bass Morone saxatilus). The total supply fluctuated by an order of magnitude; depending on the year, either autochthonous sources (phytoplankton production) or allochthonous sources (riverine loading) could be dominant. The primary cause of the year-to-year change was variability of freshwater inflows from the Sacramento and San Joaquin rivers, and its magnitude was much larger than long-term changes arising from marsh destruction and point source decreases. Although interannual variability of the total organic carbon supply could not be assessed for the southern reach, year-to-year changes in phytoplankton production were much smaller than in Suisun Bay, reflecting a relative lack of river influence.

California

1993 Annual Report: San Francisco estuary regional monitoring program for trace substances

This first annual report of the San Francisco Estuary Regional Monitoring Program contains the results of monitoring measurements made in 1993. Measurements of conventional water quality parameters and trace contaminant concentrations were made at 16 stations throughout the Estuary three times during the year: the wet period (March), during declining Delta outflow (May), and during the dry period (September). Water toxicity tests were conducted at 8 of those stations. Measurements of sediment quality and contaminant concentrations were made at the same 16 stations during the wet and dry sampling periods. Sediment toxicity was measured at 8 of those stations. Transplanted, bagged bivalve bioaccumulation and condition was measured at 11 stations during the wet and dry sampling periods. Water Monitoring. Total or near-total (dissolved + particulate, see text) arsenic, cadmium, selenium, and dissolved (0.45 &micro;m filtered) arsenic, cadmium, copper, nickel, silver, and zinc in water were highest in the South Bay. In general, dissolved metals in water were usually lowest in the Central Bay due to ocean influences. Near-total nickel and total mercury in water were highest in the northern estuary (San Pablo and Suisun Bays). Dissolved chromium and lead were highest at the Sacramento and San Joaquin River confluence stations. Six of the ten dissolved trace metals were highest in March during high runoff. Dissolved and total arsenic, selenium, and near-total cadmium were highest in September. Concentrations of trace organic contaminants are reported for the March sampling period. Total PAHs and PCBs were highest in the South Bay, but PCBs were also high in the Napa River. Dissolved PAHs were highest in the Central Bay, and dissolved PCBs were highest in the Napa River. Total and dissolved pesticides were highest in the Sacramento River and in the Extreme South Bay. Concentrations of trace elements in water (except selenium) were usually closely related with other environmental parameters. Total or near-total metals concentrations in water were most often associated with the amount of particulate material (TSS) in the water. Dissolved concentrations were usually associated with salinity or dissolved organic carbon (DOC) content. Dissolved PAHs were well correlated with TSS, but dissolved and total trace organic contaminants were poorly correlated with other water parameters. Based on deviations from conservative mixing of fresh and salt water, three different patterns of possible sources of metals were identified in 1993. For dissolved chromium and lead, rivers and local runoff appeared to be important sources. For dissolved arsenic, cadmium, copper, and nickel year-round inputs from the South Bay appeared to be important sources. Dissolved mercury, selenium, and zinc were associated with local runoff in the South Bay during the wet period. Dissolved silver did not fit any of these patterns. Although most contaminant concentrations were below water quality objectives, several trace contaminants were above the objectives at some stations. Comparisons to water quality objectives are used as a guide for evaluation of contaminant concentrations, but there are some differences in the way the RMP data are measured and that prescribed for regulatory purposes (see text). Concentrations of 5 metals in water were above EPA or Regional Basin Plan water quality objectives at six stations (see Table 30). Most of these elevated levels occurred at the northern estuary stations. Total PCB concentrations were above EPA human health objectives at all RMP stations. The pesticides chlordane, dieldrin, and DDTs were above the EPA objectives at several RMP stations, particularly at the northern-most, and river confluence stations. Although some of the contaminant concentrations were above water quality objectives, water toxicity tests (96 hour algal growth and 48 hour bivalve larval development tests) did not indicate toxicity (sometimes inconclusive) associated with the water samples collected at any of the RMP stations in 1993. Exposure to Bay San Francisco Estuary Regional Monitoring Program Regional Monitoring Program 1993 Report ii water actually enhanced algal growth at most stations. In addition to the Estuary-wide sampling, the Sacramento and San Joaquin Rivers were sampled upstream from their confluence. Stations in each river were sampled six times over a 6 week period of high flows. In the Sacramento River, seven of the ten dissolved metals measured had concentrations lower than those measured at the river confluence stations. Some metals concentrations in the San Joaquin River were higher, and some were lower than concentrations from the river confluence station. Metals concentrations in the Sacramento River were poorly related to river flow because the station at Rio Vista is under considerable tidal influence. In the San Joaquin River, flows were inversely related to 7 of 10 total metals concentrations. Sediment Monitoring. Concentrations of silver, mercury, and lead in sediment were highest in the South Bay. However, concentrations of most trace metals in sediments were highest in the northern estuary at stations with the finest (silt, clay) sediments. The northern estuary stations with the coarsest (sand, shell) sediments generally had the lowest metals concentrations. There were differences in concentrations of cadmium, lead, and selenium in sediments between the sampling periods, but no consistent trend as to which sampling period had higher values. In September, PAHs and PCBs in sediments were highest in the Central Bay, but pesticides in sediments were highest in the northern estuary and Extreme South Bay. NOAA&rsquo;s Median Effects Ranges (ERM) for sediments were used as a guide for evaluation of sediment contaminant concentrations. Nickel was the only trace contaminant in sediment above the ERM guidelines, and it was high at all RMP stations. These high levels are probably due to natural, geologic sources. Although sediment contaminant concentrations were below ERMs, sediment toxicity tests (10 day amphipod mortality, and 48 hour bivalve larval development in elutriates) indicated toxicity at all stations tested. Sediment factors that could have caused the toxicity were not investigated. Bivalve Bioaccumulation. Mussels, oysters, and freshwater clams were transplanted to the RMP stations to evaluate bioaccumulation of trace substances. Trace metals were bioaccumulated at nearly all RMP stations. However, arsenic, lead, and mercury did not appear to bioaccumulate. There was generally more bioaccumulation during the dry season than during the wet season. In September, PAHs, PCBs, and pesticides accumulated in all samples. Bioaccumulation of PAHs and pesticides was generally highest at the river confluence stations, and the Napa River. PCBs accumulated most at Redwood Creek. There were substantial differences in the degree of bioaccumulation among the species. Oysters appeared to accumulate higher concentrations of trace metals than the other species, especially copper, which may be a natural phenomenon. There are no established tissue contaminant standards for trace metal and organic contaminants. Therefore, comparisons to Median International Standards (MIS) for human consumption, or U.S. Food and Drug Administration (USFDA) action levels for trace organics are used to evaluate the bioaccumulation results. Concentrations of selenium were higher than MIS guidelines at all stations during the wet season. Other trace metal concentrations were higher than MIS guidelines at various stations during one or the other sampling period. However, none of the bivalves contained concentrations above the USFDA or National Academy of Sciences (NAS) guidelines for trace organic contaminants. The transplanted bivalves survived well at all stations except in the Napa River where less than 35% survived during both sampling seasons. Measures of bivalve condition (dry weight, shell volume) indicated that bivalves deployed in the Central Bay grew significantly, but those at most other stations actually lost weight. Whether these differences were due to natural causes such as salinity or food supply, or to contamination, was not determined. Pilot Studies. Two pilot monitoring studies were conducted in 1993. A pilot study of Estuary hydrography and phytoplankton was conducted by scientists from the U.S. Summary Geological Survey in Menlo Park and U.C. Davis. Water column profiles at up to 37 stations were monitored along a transect of the Estuary run monthly between the South Bay and the Delta. The primary objective of this study was to define physical (salinity, temperature, suspended particulate matter, and light penetration), chemical (dissolved oxygen) and biological (chlorophyll a) characteristics of Estuary water that may influence other chemical and biological reactions. A second objective was to investigate planktonic indicators of ecosystem structure and function. The data collected in 1993 showed the extent and duration of the spring phytoplankton bloom in the South Bay, other localized blooms in the northern estuary, the stratification and mixing associated with the entrapment zone in the northern estuary, and mixing in the Estuary resulting from the high rainfall in 1993. Knowledge of the duration and extent of these natural features of the Estuary provide context for interpretation of the RMP contaminant data collected only 3 times per year. Another pilot study of suspended sediment transport processes was conducted by the USGS in Sacramento. This study used continuous recording sensors at Point San Pablo and the Bay Bridge to measure the amount of suspended sediment in the water at mid-depth and near the bottom, as well as tide height. The objectives of this study were to estimate which factors determine suspended solids concentrations in the Central Bay and to collect time series of suspended solids that are appropriate for continuous monitoring of suspended solids and for calibration and validation of numerical models. The investigators determined that spring tides accounted for most of the variation in suspended solids concentrations at the stations monitored, not runoff from the Sacramento or San Joaquin Rivers, or semidiurnal and diurnal tides. Comparisons were also made between measurements made by the continuous recordings and the RMP samples collected during the regular monitoring cruises. The different ways of measuring TSS were generally comparable, however only 3 measurements per year as made by the RMP could not provide the information of TSS variation actually occurring in the Estuary. This information is important because as shown by the RMP data, total contaminant concentrations in Estuary water is largely dependent on the TSS in the water. This implies that the RMP measurements alone cannot determine accurately the range of contaminant concentrations without better characterizing the dynamics of TSS. The RMP Pilot Studies are important to the developing RMP because they will help put RMP measurements into the perspective of Estuary processes and mechanisms at other time scales. The studies can relate those processes to the RMP measurements and will facilitate revision of sampling design and interpretation. Summaries of other monitoring activities pertinent to regional monitoring are also included in the Report: a description of the Regional Board&rsquo;s Bay Protection Studies, the Sacramento Coordinated Monitoring Program, and a wetlands monitoring plan are included.

California

GIS mapping of earthquake ground shaking in San Francisco, California

Severe earthquakes of the last decade in Mexico, Armenia, and the United States have reemphasized the importance of local geologic site conditions in estimating damage and consequent losses. Recent advances in geographic information system (GIS) technology have created new opportunities for maintaining and integrating extensive spatial databases for applications in seismic hazard analysis. Ground motion data and damage distributions from past earthquakes are combined with GIS databases of geologic information to prepare preliminary maps for inferring input ground motion levels for earthquake resistant design. Maps of bedrock elevation, surface topography, and surface geology are used to develop maps of soil thickness and predominant period. Ground motion attenuation relationships are used to create maps estimating ground shaking intensity for a uniform ground condition. Relationships between geologic characteristics, ground motion amplification, and earthquake intensity are used to produce amplification capability maps. Estimated ground shaking for the uniform ground condition is combined with amplification capability to develop maps predicting regional ground shaking intensity. The methods of predictive GIS mapping described here are useful for estimating characteristics of input ground motion in many urbanized seismic regions of the world.

California

On the characteristics of local geology and their influence on ground motions generated by the Loma Prieta earthquake in the San Francisco Bay region, California

Strong ground motions recorded at 34 sites in the San Francisco Bay region from the Loma Prieta earthquake show marked variations in characteristics dependent on crustal structure and local geological conditions. Peak horizontal acceleration and velocity inferred for sites underlain by “rock” generally occur on the transverse component of motion. They are consistently greater with lower attenuation rates than the corresponding mean value predicted by empirical curves based on previous strong-motion data. Theoretical amplitude distributions and synthetic seismograms calculated for 10-layer models suggest that “bedrock” motions were elevated due in part to the wide-angle reflection of S energy from the base of a relatively thin (25 km) continental crust in the region. Characteristics of geologic and geotechnical units as currently mapped for the San Francisco Bay region show that average ratios of peak horizontal acceleration, velocity and displacement increase with decreasing mean shear-wave velocity. Ratios of peak acceleration for sites on “soil” (alluvium, fill/Bay mud) are statistically larger than those for sites on “hard rock” (sandstone, shale, Franciscan Complex). Spectral ratios establish the existence of predominant site periods with peak amplifications near 15 for potentially damaging levels of ground motion at some sites underlain by alluvium and fill/bay mud. Average spectral amplifications inferred for vertical and the mean horizontal motion are, respectively, (1,1) for sites on the Franciscan Complex (KJf), (1.4, 1.5) for sites on Mesozoic and Tertiary rocks (TMzs), (2.1, 2.0) for sites on the Santa Clara Formation (QTs), (2.3, 2.9) for sites on alluvium (Qal), and (2.1, 4.0) for sites on fill/Bay mud (Qaf/Qhbm). These mean values are not statistically different at the 5% significance level from those inferred from previous low-strain data. Analyses suggest that soil amplification and reflected crustal shear energy were major contributors to levels of ground motion sufficient to cause damage to vulnerable structures at distances near 100 km in the cities of San Francisco and Oakland.

California