USGS Science⌕ Search

Geology topics

Research about Florida

Source-linked reports with geographic coverage including Florida.

At least 883 records · Page 49Linked to original sources
USGS2009

Foraminiferal assemblages in Biscayne Bay, Florida, USA: Responses to urban and agricultural influence in a subtropical estuary

This study assessed foraminiferal assemblages in Biscayne Bay, Florida, a heavily utilized estuary, interpreting changes over the past 65 years and providing a baseline for future comparisons. Analyses of foraminiferal data at the genus level revealed three distinct biotopes. The assemblage from the northern bay was characterized by stress-tolerant taxa, especially Ammonia , present in low abundances (∼2.0 × 10 3 foraminifers/gram) though relatively high diversity (∼19 genera/sample). The southwestern margin of the bay was dominated by Ammonia and Quinqueloculina , an assemblage characterized by the lowest diversities (∼12 genera/sample) and highest abundances (∼1.1 × 10 4 foraminifers/gram), influenced by both reduced salinity and elevated organic-carbon concentrations. A diverse assemblage of smaller miliolids and rotaliids (∼26 genera/sample) characterized the open-bay assemblage, which also had a significant component (∼10%) of taxa that host algal endosymbionts. In the past 65 years, populations of symbiont-bearing taxa, which are indicators of normal-marine conditions, have decreased while stress-tolerant taxa, especially Ammonia spp., have increased in predominance.

Florida↗
USGS2009

Defining winter trophic habitat of juvenile Gulf Sturgeon in the Suwannee and Apalachicola rivermouth estuaries, acoustic telemetry investigations

Three automated listening post-telemetry studies were undertaken in the Suwannee and Apalachicola estuaries to gain knowledge of habitats use by juvenile Gulf Sturgeons ( Acipenser oxyrinchus desotoi ) on winter feeding grounds. A simple and reliable method for external attachment of small acoustic tags to the dorsal fin base was developed using shrink-tubing. Suspending receivers on masts below anchored buoys improved reception and facilitated downloading; a detection range of 500–2500 m was realized. In the Apalachicola estuary, juvenile GS stayed in shallow water (< 2 m) within the estuarine transition zone all winter in the vicinity of the Apalachicola River mouth. Juvenile GS high-use areas did not coincide with high density benthic macrofauna areas from the most recent (1999) benthos survey. In the Suwannee estuary, juveniles ranged widely and individually throughout oligohaline to mesohaline subareas of the estuary, preferentially using mesohaline subareas seaward of Suwannee Reef (52% of acoustic detections). The river mouth subarea was important only in early and late winter, during the times of adult Gulf Sturgeon migrations (41% of detections). Preferred winter feeding subareas coincided spatially with known areas of dense macrofaunal benthos concentrations. Following a dramatic drop in air and water temperatures, juvenile GS left the river mouth and estuary, subsequently being detected 8 km offshore in polyhaline open Gulf of Mexico waters, before returning to the estuary. Cold-event offshore excursions demonstrate that they can tolerate full-salinity polyhaline waters in the open Gulf of Mexico, for at least several days at a time. For juvenile sturgeons, the stress and metabolic cost of enduring high salinity (Jarvis et al., 2001; McKenzie et al., 2001; Singer and Ballantyne, 2002) for short periods in deep offshore waters seems adaptively advantageous relative to the risk of cold-event mortality in shallow inshore waters of lower salinity. Thus, while juveniles can tolerate high salinities for days to weeks to escape cold events, they appear to make only infrequent use of open polyhaline waters. Throughout the winter foraging period, juvenile GS stayed primarily within the core area of Suwannee River mouth influence, extending about 12 km north and south of the river mouth, and somewhat seaward of Suwannee Reef (< 5 km offshore). None were detected departing the core area past either of the northern or southern acoustic gates, located 66 and 52 km distant from the river mouth, respectively.

Florida↗
USGS2009

A habitat assessment for Florida panther population expansion into central Florida

One of the goals of the Florida panther ( Puma concolor coryi ) recovery plan is to expand panther range north of the Caloosahatchee River in central Florida. Our objective was to evaluate the potential of that region to support panthers. We used a geographic information system and the Mahalanobis distance statistic to develop a habitat model based on landscape characteristics associated with panther home ranges. We used cross-validation and an independent telemetry data set to test the habitat model. We also conducted a least-cost path analysis to identify potential habitat linkages and to provide a relative measure of connectivity among habitat patches. Variables in our model were paved road density, major highways, human population density, percentage of the area permanently or semipermanently flooded, and percentage of the area in natural land cover. Our model clearly identified habitat typical of that found within panther home ranges based on model testing with recent telemetry data. We identified 4 potential translocation sites that may support a total of approximately 36 panthers. Although we identified potential habitat linkages, our least-cost path analyses highlighted the extreme isolation of panther habitat in portions of the study area. Human intervention will likely be required if the goal is to establish female panthers north of the Caloosahatchee in the near term.

Florida↗
USGS2009

Site characteristics and prey abundance at foraging sites used by Lesser Scaup ( Aythya affinis ) wintering in Florida

We examined site characteristics and prey abundances where wintering Aythya affinis (Lesser Scaup; hereafter scaup) foraged within three regions of the Indian River Lagoon system in central Florida. We observed that scaup concentrated in the Indian and Banana rivers; however, density of prey items did not differ between foraging sites and random sites. We also found that site characteristics were similar between foraging and random sites. Differences in site characteristics between random points across all three regions did not explain the distribution of Foraging scaup (no scaup foraged in the Mosquito Lagoon); however, prey densities were approximately 3 times lower in the Mosquito Lagoon region. Our study suggests that current habitat conditions within the northern Indian River Lagoon system meet the overwintering requirements of scaup; however, prey densities in the Mosquito Lagoon may have been too low to be profitable for foraging scaup during the period of our study.

Florida↗
USGS2009

Vegetation effects on fish distribution in impounded salt marshes

We compared the density and biomass of resident fish in vegetated and unvegetated flooded habitats of impounded salt marshes in the northern Indian River Lagoon (IRL) Estuary of east-central Florida. A 1 -m 2 throw trap was used to sample fish in randomly located, paired sample plots ( n = 198 pairs) over 5 seasons in 7 impoundments. We collected a total of 15 fish taxa, and 88% of the fishes we identified from the samples belonged to three species: Cyprinodon variegatus (Sheepshead Minnow), Gambusia holbrooki (Eastern Mosquitofish), and Poecilia latipinna (Sailfin Molly). Vegetated habitat usually had higher density and biomass of fish. Mean fish density (and 95% confidence interval) for vegetated and unvegetated sites were 8.2 (6.7&ndash;9.9) and 2.0 (1.6&ndash;2.4) individuals m -2 , respectively; mean biomass (and 95%) confidence interval) for vegetated and unvegetated sites were 3.0 (2.5&ndash;3.7) and 1.1 (0.9&ndash;1.4) g m -2 , respectively. We confirmed previous findings that impounded salt marshes of the northern IRL Estuary produce a high standing stock of resident fishes. Seasonal patterns of abundance were consistent with fish moving between vegetated and unvegetated habitat as water levels changed in the estuary. Differences in density, mean size, and species composition of resident fishes between vegetated and unvegetated habitats have important implications for movement of biomass and nutrients out of salt marsh by piscivores (e.g., wading birds and fishes) via a trophic relay.

Florida↗
USGS2009

Hurricane Wilma's impact on overall soil elevation and zones within the soil profile in a mangrove forest

Soil elevation affects tidal inundation period, inundation frequency, and overall hydroperiod, all of which are important ecological factors affecting species recruitment, composition, and survival in wetlands. Hurricanes can dramatically affect a site's soil elevation. We assessed the impact of Hurricane Wilma (2005) on soil elevation at a mangrove forest location along the Shark River in Everglades National Park, Florida, USA. Using multiple depth surface elevation tables (SETs) and marker horizons we measured soil accretion, erosion, and soil elevation. We partitioned the effect of Hurricane Wilma's storm deposit into four constituent soil zones: surface (accretion) zone, shallow zone (0–0.35 m), middle zone (0.35–4 m), and deep zone (4–6 m). We report expansion and contraction of each soil zone. Hurricane Wilma deposited 37.0 (± 3.0 SE) mm of material; however, the absolute soil elevation change was + 42.8 mm due to expansion in the shallow soil zone. One year post-hurricane, the soil profile had lost 10.0 mm in soil elevation, with 8.5 mm of the loss due to erosion. The remaining soil elevation loss was due to compaction from shallow subsidence. We found prolific growth of new fine rootlets (209 ± 34 SE g m −2 ) in the storm deposited material suggesting that deposits may become more stable in the near future (i.e., erosion rate will decrease). Surficial erosion and belowground processes both played an important role in determining the overall soil elevation. Expansion and contraction in the shallow soil zone may be due to hydrology, and in the middle and bottom soil zones due to shallow subsidence. Findings thus far indicate that soil elevation has made substantial gains compared to site specific relative sea-level rise, but data trends suggest that belowground processes, which differ by soil zone, may come to dominate the long term ecological impact of storm deposit.

Florida↗
USGS2009

Multi-state succession in wetlands: a novel use of state and transition models

The complexity of ecosystems and mechanisms of succession are often simplified by linear and mathematical models used to understand and predict system behavior. Such models often do not incorporate multivariate, nonlinear feedbacks in pattern and process that include multiple scales of organization inherent within real-world systems. Wetlands are ecosystems with unique, nonlinear patterns of succession due to the regular, but often inconstant, presence of water on the landscape. We develop a general, nonspatial state and transition (S and T) succession conceptual model for wetlands and apply the general framework by creating annotated succession/management models and hypotheses for use in impact analysis on a portion of an imperiled wetland. The S and T models for our study area, Water Conservation Area 3A South (WCA3), Florida, USA, included hydrologic and peat depth values from multivariate analyses and classification and regression trees. We used the freeware Vegetation Dynamics Development Tool as an exploratory application to evaluate our S and T models with different management actions (equal chance [a control condition], deeper conditions, dry conditions, and increased hydrologic range) for three communities: slough, sawgrass ( Cladium jamaicense ), and wet prairie. Deeper conditions and increased hydrologic range behaved similarly, with the transition of community states to deeper states, particularly for sawgrass and slough. Hydrology is the primary mechanism for multi-state transitions within our study period, and we show both an immediate and lagged effect on vegetation, depending on community state. We consider these S and T succession models as a fraction of the framework for the Everglades. They are hypotheses for use in adaptive management, represent the community response to hydrology, and illustrate which aspects of hydrologic variability are important to community structure. We intend for these models to act as a foundation for further restoration management and experimentation which will refine transition and threshold concepts.

Florida↗
USGS2009

A centennial tribute, 1906-2006: History of U.S. Geological Survey streamgaging activities for the Suwannee River at White Springs, Florida

For centuries, the banks of the Suwannee River at White Springs were considered a sacred ground where people sought refuge in its 'healing waters'. Many believed that the mineral-enriched waters cured illnesses. The U.S. Geological Survey began continuous streamgaging activities at White Springs, Florida, in 1906 after an increase in congressional appropriations and rapid town development due to growing tourism and residential population. In 1906, streamgage data was a once-per-day gage reading that were handwritten in a water-level booklet by a local observer with discharge measurements taken every 6 to 8 weeks by a hydrographer. In 2006, real-time data were recorded at 1-hour increments and transmitted to U.S. Geological Survey computer networks using the Geostationary Operational Environmental Satellite, thus enabling the general public to access readings within minutes of the actual measurement. Additional data and measurements are taken and made available for high or low flows that occur during significant floods and droughts. The gage at White Springs has recorded several historic hydrologic events that affected the Suwannee River and surrounding areas. Major droughts include those during 1931-35, 1949-57, and 1998-2002. Severe floods occurred in 1948, 1973, and 2004. On April 10, 1973, the discharge was 38,100 cubic feet per second, which is the highest recorded discharge for the period of record. A flood of this magnitude is expected at a recurrence interval of about once every 200 to 500 years.

Florida↗
USGS2009

Archive of digital boomer and CHIRP seismic reflection data collected during USGS field activity 08LCA03 in Lake Panasoffkee, Florida, May 2008

In May of 2008, the U.S. Geological Survey (USGS) conducted geophysical surveys in Lake Panasoffkee, located in central Florida, as part of the USGS Lakes and Coastal Aquifers (LCA) study. This report serves as an archive of unprocessed digital boomer and Compressed High Intensity Radar Pulse (CHIRP)* seismic reflection data, trackline maps, navigation files, Field Activity Collection System (FACS) logs, Geographic Information System (GIS) files, and formal Federal Geographic Data Committee (FGDC) metadata. Filtered and gained (a relative increase in signal amplitude) digital images of the seismic profiles and geospatially corrected interactive profiles are also provided. Refer to the Acronyms page for expansions of acronyms and abbreviations used in this report. *Due to poor data acquisition conditions associated with the lake bottom sediments, only two CHIRP tracklines were collected during this field activity. The archived trace data are in standard Society of Exploration Geophysicists (SEG) SEG-Y format (Barry and others, 1975) and may be downloaded and processed with commercial or public domain software such as Seismic Unix (SU). Example SU processing scripts and USGS software for viewing the SEG-Y files (Zihlman, 1992) are provided. The USGS Florida Integrated Science Center (FISC) - St. Petersburg assigns a unique identifier to each cruise or field activity. For example, 08LCA03 tells us the data were collected in 2008 for the Lakes and Coastal Aquifers (LCA) study and the data were collected during the third field activity for that study in that calendar year. Refer to http://walrus.wr.usgs.gov/infobank/programs/html/definition/activity.html for a detailed description of the method used to assign the field activity ID. The naming convention used for each seismic line is as follows: yye##a, where 'yy' are the last two digits of the year in which the data were collected, 'e' is a 1-letter abbreviation for the equipment type (for example, b for boomer and c for CHIRP), '##' is a 2-digit number representing a specific track, and 'a' is a letter representing the section of a line if recording was prematurely terminated or rerun for quality or acquisition problems. The boomer plate is an acoustic energy source that consists of capacitors charged to a high voltage and discharged through a transducer in the water. The transducer is towed on a sled floating on the water surface and, when discharged, emits a short acoustic pulse, or shot, which propagates through the water, sediment column, or rock beneath. The acoustic energy is reflected at density boundaries (such as the seafloor, sediment, or rock layers beneath the seafloor), detected by the receiver, and recorded by a PC-based seismic acquisition system. This process is repeated at timed intervals (for example, 0.5 s) and recorded for specific intervals of time (for example, 100 ms). In this way, a two-dimensional (2-D) vertical profile of the shallow geologic structure beneath the ship track is produced. Figure 1 displays the boomer acquisition geometry. The EdgeTech SB-424 CHIRP system used for this survey has a vertical resolution of 4 - 8 cm, a penetration depth that is usually less than 2 m beneath the seafloor, and uses a signal of continuously varying frequency. The towfish is a sound source and receiver, which is typically towed 2 - 5 m above the seafloor. The acoustic energy is reflected at density boundaries (such as the seafloor or sediment layers beneath the seafloor), detected by a receiver, and recorded by a PC-based seismic acquisition system. This process is repeated at timed intervals (for example, 0.125 s) and recorded for specific intervals of time (for example, 50 ms); the resulting profile is a two-dimensional vertical image of the shallow geologic structure beneath the ship track. Figure 2 displays the acquisition geometry for the CHIRP system. Refer to table 1 for a summary of acquisition parameters and table 2 for trackline statistics.

Florida↗
USGS2009

ATM coastal topography-Florida 2001: Western Panhandle

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the western Florida panhandle coastline, acquired October 2-4 and 7-10, 2001. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative scanning Lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning Lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that represent submerged or first surface topography.

Florida↗
USGS2009

ATM Coastal Topography-Florida 2001: Eastern Panhandle

These remotely sensed, geographically referenced elevation measurements of Lidar-derived first surface (FS) topography were produced collaboratively by the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL, and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate datasets of the eastern Florida panhandle coastline, acquired October 2, 2001. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative scanning Lidar instrument originally developed by NASA, and known as the Airborne Topographic Mapper (ATM), was used during data acquisition. The ATM system is a scanning Lidar system that measures high-resolution topography of the land surface and incorporates a green-wavelength laser operating at pulse rates of 2 to 10 kilohertz. Measurements from the laser-ranging device are coupled with data acquired from inertial navigation system (INS) attitude sensors and differentially corrected global positioning system (GPS) receivers to measure topography of the surface at accuracies of +/-15 centimeters. The nominal ATM platform is a Twin Otter or P-3 Orion aircraft, but the instrument may be deployed on a range of light aircraft. Elevation measurements were collected over the survey area using the ATM system, and the resulting data were then processed using the Airborne Lidar Processing System (ALPS), a custom-built processing system developed in a NASA-USGS collaboration. ALPS supports the exploration and processing of Lidar data in an interactive or batch mode. Modules for presurvey flight line definition, flight path plotting, Lidar raster and waveform investigation, and digital camera image playback have been developed. Processing algorithms have been developed to extract the range to the first and last significant return within each waveform. ALPS is routinely used to create maps that represent submerged or first surface topography.

Florida↗
USGS2009

Archive of digital boomer seismic reflection data collected offshore east-central Florida during USGS cruise 00FGS01, July 14-22, 2000

In July of 2000, the U.S. Geological Survey (USGS), in cooperation with the Florida Geological Survey (FGS), conducted a geophysical survey of the Atlantic Ocean offshore Florida's east coast from Brevard County to northern Martin County. This report serves as an archive of unprocessed digital boomer seismic reflection data, trackline maps, navigation files, Geographic Information System (GIS) information, digital and handwritten Field Activity Collection System (FACS) logs, and Federal Geographic Data Committee (FGDC) metadata. A filtered and gained (a relative increase in signal amplitude) digital image of each seismic profile is also provided. Refer to the Acronyms page for expansions of all acronyms and abbreviations used in this report. The archived trace data are in standard Society of Exploration Geophysicists (SEG) SEG-Y format (Barry and others, 1975) and may be downloaded and processed with commercial or public domain software such as Seismic Unix (SU) (Cohen and Stockwell, 2005). Example SU processing scripts and USGS Software for viewing the SEG-Y files (Zihlman, 1992) are also provided. The USGS St. Petersburg Coastal and Marine Science Center assigns a unique identifier to each cruise or field activity. For example, 00FGS01 tells us the data were collected in 2000 for cooperative work with the Florida Geological Survey (FGS) and the data were collected during the first field activity for that study in that calendar year. Refer to http://walrus.wr.usgs.gov/infobank/programs/html/definition/activity.html for a detailed description of the method used to assign the field activity ID. The boomer plate is an acoustic energy source that consists of capacitors charged to a high voltage and discharged through a transducer in the water. The transducer is towed on a sled floating on the water surface and when discharged, emits a short acoustic pulse, or shot, which propagates through the water, sediment column, or rock beneath. The acoustic energy is reflected at density boundaries (such as the seafloor, sediment, or rock layers beneath the seafloor), detected by the receiver, and recorded by a PC-based seismic acquisition system. This process is repeated at timed intervals (for example, 0.5 s) and recorded for specific intervals of time (for example, 100 ms). In this way, a two-dimensional (2D) vertical profile of the shallow geologic structure beneath the ship track is produced. Figure 1 displays the acquisition geometry. Refer to table 1 for a summary of acquisition parameters. The unprocessed seismic data are stored in SEG-Y format (Barry and others, 1975). For a detailed description of the data format, refer to the SEG-Y Format page. See the How To Download SEG-Y Data page for download instructions. The printable profiles provided are GIF images that were filtered and gained using Seismic Unix software. Refer to the Software page for details about the processing and examples of the processing scripts. The printable profiles can be viewed from the Profiles page or from links located on the trackline maps. To view the trackline maps and navigation files, and for more information about these items, see the Navigation page. Detailed information about the navigation system used can be found in table 1. Of a total record length of 200 ms, only the upper 100 ms of each profile are displayed because no useful information was observed deeper in the sections. A 10 ms deep water delay appears on lines b57-b63 and sl2-sl28. No digital data were collected for line sl6. However, line sl6r is a second attempt to collect digital data for this line. Digital data and 500-shot-interval location navigation are not available for the last 1,161 shots of line sl26 due to an equipment malfunction.

Florida↗
USGS2009

USGS field activity 08FSH01 on the west Florida shelf, Gulf of Mexico, in August 2008

From August 11 to 15, 2008, a cruise led by the U.S. Geological Survey (USGS) collected air and sea surface partial pressure of carbon dioxide (pCO2), pH, dissolved inorganic carbon (DIC), and total alkalinity (TA) data on the west Florida shelf. Approximately 1,600 data points were collected underway over a 650-kilometer (km) trackline using the Multiparameter Inorganic Carbon Analyzer (MICA). The collection of data extended from Crystal River southward to Marco Island, Florida (~400 km), and westward up to 160 km off the Florida coast. Discrete water samples from approximately 40 locations were also taken at specific localities to corroborate underway data measurements. The USGS St. Petersburg Coastal and Marine Science Center (SPCMSC) assigns a unique identifier to each cruise or field activity. For example, 08FSH01 tells us the data were collected in 2008 for the Response of Florida Shelf (FSH) Ecosystems to Climate Change project, and the data were collected during the first field activity for that study in that calendar year.

Florida↗
USGS2009

USGS field activity 09FSH01 on the west Florida shelf, Gulf of Mexico, in February 2009

From February 24 to 28, 2009, a cruise led by the U.S. Geological Survey (USGS) collected air and sea surface partial pressure of carbon dioxide (pCO2), pH, dissolved inorganic carbon (DIC), and total alkalinity (TA) data on the west Florida shelf. Approximately 1,800 data points were collected underway over a 1,300-kilometer (km) trackline using the Multiparameter Inorganic Carbon Analyzer (MICA). The collection of data extended from Crystal River to Marco Island, Florida (~400 km), and westward up to 160 km off the Florida coast. Discrete water samples were also taken at specific localities to corroborate underway data measurements. The USGS St. Petersburg Coastal and Marine Science Center (SPCMSC) assigns a unique identifier to each cruise or field activity. For example, 09FSH01 tells us that the data were collected in 2009 for the Response of Florida Shelf (FSH) Ecosystems to Climate Change project, and the data were collected during the first field activity for that study in that calendar year.

Florida↗
USGS2009

USGS field activity 09FSH02 on the west Florida shelf, Gulf of Mexico, in August 2009

From August 17 to 21, 2009, a cruise led by the U.S. Geological Survey (USGS) collected air and sea surface partial pressure of carbon dioxide (pCO2), pH, dissolved inorganic carbon (DIC), and total alkalinity (TA) data on the west Florida shelf. Approximately 2,000 data points were collected underway over a 1,320-kilometer (km) track line using the Multiparameter Inorganic Carbon Analyzer (MICA). The collection of data extended from Crystal River to Marco Island, Florida (~400 km), and westward up to 160 km off the Florida coast. Discrete water samples were also taken at specific localities to corroborate underway data measurements. The USGS St. Petersburg Coastal and Marine Science Center (SPCMSC) assigns a unique identifier to each cruise or field activity. For example, 09FSH02 tells us that the data were collected in 2009 for the Response of Florida Shelf (FSH) Ecosystems to Climate Change project, and the data were collected during the second field activity for that study in that calendar year.

Florida↗
USGS2009

Coastal change during Hurricane Dennis 2005

Hurricane Dennis made landfall as a Category 3 storm on Santa Rosa Island in the Florida Panhandle on July 10, 2005. Exposed to some of the strongest winds, Santa Rosa Island suffered erosion, as well as severe overwash. A storm surge of 2 m was recorded near Navarre Beach. The U.S. Geological Survey (USGS) and U.S. Army Corps of Engineers (USACE) are collaborating in a research project investigating coastal change that occurred as a result of Hurricane Dennis. The USGS acquired still oblique aerial photography both before and after hurricane landfall to better understand the impacts of extreme storms on coastal environments. On Tuesday, July 12, 2005, scientists conducted an aerial photographic survey of Santa Rosa Island, Florida, that was impacted by Hurricane Dennis. The photographs were compared to pre-Dennis photographs taken in July 2001 and after the landfall of Hurricane Ivan in September 2004 to illustrate extreme coastal change. On Santa Rosa Island, the storm eroded dunes and beaches, and overwashed roads. In Navarre Beach, parking lots and roads were covered with sand and dune walkovers damaged or destroyed.

Florida↗
USGS2009

Assessing the vulnerability of public-supply wells to contamination: Floridan aquifer system near Tampa, Florida

This fact sheet highlights findings from the vulnerability study of a public-supply well in Temple Terrace, Florida, northeast of Tampa. The well selected for study typically produces water at the rate of 700 gallons per minute from the Upper Floridan aquifer. Water samples were collected at the public-supply well and at monitoring wells installed in or near the simulated zone of contribution to the supply well. Samples of untreated water from the public-supply wellhead contained the undesirable constituents nitrate, arsenic, uranium, radon-222, volatile organic compounds (VOCs), and pesticides, although all were detected at concentrations less than established drinking-water standards, where such standards exist. Overall, study findings point to four primary factors that affect the movement and fate of contaminants and the vulnerability of the public-supply well in Temple Terrace: (1) groundwater age (how long ago water entered, or recharged, the aquifer); (2) short-circuiting of contaminated water through sinkholes; (3) natural geochemical processes within the aquifer; and (4) pumping stress. Although the public-supply well is completed in the Upper Floridan aquifer, it produces water with concentrations of nitrate, VOCs, and the natural contaminant radon that are intermediate between the typical composition of water from the Upper Floridan aquifer and that of the overlying surficial aquifer system. Mixing calculations show that the water produced by the public-supply well could consist of upwards of 50 percent water from the surficial aquifer system mixed with water from the Upper Floridan aquifer. Anthropogenically affected water from the surficial aquifer system travels rapidly to depth through sinkholes that must be directly connected to the cavernous zone intersected by the public-supply well (and several other production wells in the region). Such solution features serve as fast pathways to the well and circumvent the natural attenuation of nitrate and radon that occurs when water from the surficial aquifer flows downward through the confining unit and then through the Upper Floridan aquifer matrix. Roughly 50 percent of the simulated flow to the public-supply well consists of water less than about 10 years old, thus making the well vulnerable to contamination from human activities. Sampling at various depths in the public-supply well during pumping and nonpumping conditions showed that water entering the well from the cavernous zone had much higher arsenic concentrations during pumping conditions (18.9 ug/L) than during nonpumping conditions (4.2 ug/L). This implies that movement of arsenic to the public-supply well from the cavernous zone is enhanced by pumping. One possible explanation is that pumping increases the movement of water with elevated dissolved oxygen content through the cavernous zone, which causes dissolution of arsenic associated with pyrite. All public-supply wells in the area may not have the same level of vulnerability as the well studied - many of the public-supply wells in the region have lower pumping rates and longer open intervals that may draw in a larger proportion of old water that predates anthropogenic influences. Determining the similarity of water produced by various public-supply wells in the region to that of the surficial aquifer system is one measure of well vulnerability that could be used to prioritize monitoring and land-use planning efforts to protect the most vulnerable wells.

Florida↗