S. Eittreim | USGS Science

USGS1998

The influence of the San Gregorio fault on the morphology of Monterey Canyon

A side-scan sonar survey was conducted of Monterey Canyon and the San Gregorio fault zone, off shore of Monterey Bay. The acoustic character and morphology of the sonar images, enhanced by SeaBeam bathymetry, show the path of the San Gregorio fault zone across the shelf, upper slope, and Monterey Canyon. High backscatter linear features a few kilometers long and 100 to 200 m wide delineate the sea-floor expression of the fault zone on the shelf. Previous studies have shown that brachiopod pavements and carbonate crusts are the source of the lineations backscatter. In Monterey Canyon, the fault zone occurs where the path of the canyon makes a sharp bend from WNW to SSW (1800 m). Here, the fault is marked by NW-SE-trending, high reflectivity lineations that cross the canyon floor between 1850 m and 1900 m. The lineations can be traced to ridges on the northwestern canyon wall where they have ~ 15 m of relief. Above the low-relief ridges, bowl-shaped features have been excavated on the canyon wall contributing to the widening of the canyon. We suggest that shear along the San Gregorio fault has led to the formation of the low-relief ridges near the canyon wall and that carbonate crusts, as along the shelf, may be the source of the high backscatter features on the canyon floor. The path of the fault zone across the upper slope is marked by elongated tributary canyons with high backscatter floors and 'U'-shaped cross-sectional profiles. Linear features and stepped scarps suggestive of recent crustal movement and mass-wasting, occur on the walls and floors of these canyons. Three magnitude-4 earthquakes have occurred within the last 30 years in the vicinity of the canyons that may have contributed to the observed features. As shown by others, motion along the fault zone has juxtaposed diverse lithologies that outcrop on the canyon walls. Gully morphology and the canyon's drainage patterns have been influenced by the substrate into which the gullies have formed.

Marine Geology↗

USGS1980

Current-controlled, abyssal microtopography and sedimentation in Mozambique Basin, southwest Indian Ocean

The Antarctic Bottom Water (AABW) activity and the variations in the abundance and grain size of the terrigenous sediments, derived from Africa and Madagascar land masses, are reflected in different types of microtopography in the Mozambique Basin. In southerly areas, where the sediment supply is much less, the bottom-current activity has resulted in the presence of manganese nodules, a thin veneer of sediments, and the absence of sediment waves. Farther north, along the marginal areas of the basin where the fine-grained sediments from the Africa—Madagascar source have been supplied in abundance, wavy bedforms have been generated by AABW. Wavy bedforms do not exist even in the northerly areas if coarse-grained, turbidite sediments are present on the sea floor. The continuation of acoustic reflectors from the zone of turbidites in the central areas of the basin into the zone of sediment waves along the margins, and the lithology and structures in sediment cores from these zones suggest that the turbidity-current-fed, fine-grained sediments were deposited as wavy bedforms by AABW flow. Thus, sediment waves formed readily during Pleistocene times. The enrichment of quartz and displaced Antarctic diatoms, and the relatively low kaolinite/chlorite ratios in the sediments, the north-pointing current lineations on the sea floor, the lack of any perceptible sedimentary fill in the troughs of waves, and the dense nepheloid layer in the westerly areas of the Mozambique Basin, attest to the current-controlled sedimentation and generation of wavy bedforms during Holocene time also. The formation of sediment waves in the Mozambique Basin can be modeled after a fluvial antidune mechanism. This model envisages that internal waves, focused on a benthic boundary layer cap, have been locked in phase with sediment waves in the presence of an 8–10 cm/sec current in the Mozambique Basin. A density contrast of 2·10 −6 g/cm 3 appears to exist at the tops of benthic boundary layers in the Mozambique Basin and is quite sufficient for supporting the internal waves. The densiometric Froude number calculated for a 60–280 m thick boundary layer in the basin is close to unity or greater, and is compatible with the antidune model.

Marine Geology↗