Geology topics

Roger H. Morin

Publications and source records attributed to Roger H. Morin.

16 recordsLinked to original sources

USGS2012

Lithostratigraphy from downhole logs in Hole AND-1B, Antarctica

The ANDRILL (Antarctic Drilling Project) McMurdo Ice Shelf (MIS) project drilled 1285 m of sediment in Hole AND–1B, representing the past 12 m.y. of glacial history. Downhole geophysical logs were acquired to a depth of 1018 mbsf (meters below seafloor), and are complementary to data acquired from the core. The natural gamma radiation (NGR) and magnetic susceptibility logs are particularly useful for understanding lithological and paleoenvironmental change at ANDRILL McMurdo Ice Shelf Hole AND–1B. NGR logs cover the entire interval from the seafloor to 1018 mbsf, and magnetic susceptibility and other logs covered the open hole intervals between 692 and 1018 and 237–342 mbsf. In the upper part of AND–1B, clear alternations between low and high NGR values distinguish between diatomite (lacking minerals containing naturally radioactive K, U, and Th) and diamictite (containing K-bearing clays, K-feldspar, mica, and heavy minerals). In the lower open hole logged section, NGR and magnetic susceptibility can also distinguish claystones (rich in K-bearing clay minerals, relatively low in magnetite) and diamictites (relatively high in magnetite). Sandstones can be distinguished by their high resistivity values in AND–1B. On the basis of these three downhole logs, diamictite, claystones, and sandstones can be predicted correctly for 74% of the 692–1018 mbsf interval. The logs were then used to predict facies for the 6% of this interval that was unrecovered by coring. Given the understanding of the physical property characteristics of different facies, it is also possible to identify subtle changes in lithology from the physical properties and help refine parts of the lithostratigraphy, for example, the varying terrigenous content of diatomites and the transitions from subice diamictite to open-water diatomite.

Geosphere↗

USGS2011

Drilling the central crater of the Chesapeake Bay Impact Structure: A first look

The late Eocene Chesapeake Bay impact structure is a well‐preserved example of one of Earth's largest impact craters, and its continental‐shelf setting and relatively shallow burial make it an excellent target for study. Since the discovery of the structure over a decade ago [ Edwards et al., 2004; Poag et al., 2004], test drilling by U.S. federal and state agencies has been limited to the structure's annular trough (Figure 1). In May 2004, the U.S. Geological Survey (USGS) drilled the first scientific test hole into the central crater of the Chesapeake Bay impact structure in Cape Charies,Virginia (Figure 1). This partially cored test hole, the deepest to date, penetrated postimpact sediments and impact breccias to a total depth of 823 m.

Chesapeake Bay↗

USGS2010

Heat Flow and Hydrologic Characteristics at the AND-1B borehole, ANDRILL McMurdo Ice Shelf Project, Antarctica

The Antarctic Drilling Program (ANDRILL) successfully drilled and cored a borehole, AND-1B, beneath the McMurdo Ice Shelf and into a flexural moat basin that surrounds Ross Island. Total drilling depth reached 1285 m below seafloor (mbsf) with 98 percent core recovery for the detailed study of glacier dynamics. With the goal of obtaining complementary information regarding heat flow and permeability, which is vital to understanding the nature of marine hydrogeologic systems, a succession of three temperature logs was recorded over a five-day span to monitor the gradual thermal recovery toward equilibrium conditions. These data were extrapolated to true, undisturbed temperatures, and they define a linear geothermal gradient of 76.7 K/km from the seafloor to 647 mbsf. Bulk thermal conductivities of the sedimentary rocks were derived from empirical mixing models and density measurements performed on core, and an average value of 1.5 W/mK ± 10 percent was determined. The corresponding estimate of heat flow at this site is 115 mW/m2. This value is relatively high but is consistent with other elevated heat-flow data associated with the Erebus Volcanic Province. Information regarding the origin and frequency of pathways for subsurface fluid flow is gleaned from drillers' records, complementary geophysical logs, and core descriptions. Only two prominent permeable zones are identified and these correspond to two markedly different features within the rift basin; one is a distinct lithostratigraphic subunit consisting of a thin lava flow and the other is a heavily fractured interval within a single thick subunit.

Geosphere↗

USGS2010

Theoretical analysis of the transient pressure response from a constant flow rate hydraulic conductivity test

Incorporating a flow pump into a conventional triaxial laboratory system allows fluid to be supplied to or withdrawn from the base of a sediment sample at small and constant rates. An initial transient record of hydraulic head versus time is observed which eventually stabilizes to a constant steady state gradient across the sample; values of hydraulic conductivity can subsequently be determined from Darcy's law. In this paper, analytical methods are presented for determining values of specific storage and hydraulic conductivity from the initial transient phase of such a constant flow rate test. These methods are based on a diffusion equation involving pore pressure and are analogous to those used to describe the soil consolidation process and also to interpret aquifer properties from pumping tests. Examination of the effective stress distributions within the test specimen induced during this type of measurement shows that values of specific storage corresponding to both compression and rebound conditions can be deduced and differentiated simply by reversing the direction of fluid flow. Applicability and limitations of the methods are illustrated with analyses of recently reported flow pump test measurements conducted on a silty-clay specimen.

Water Resources Research↗

USGS2010

Aquifer characteristics near cuestas and their relation to rock tensile strength

Along the northeast coast of North America, extensional tectonic processes have generated lithologic and topographic features that are common to several rift basins. A cap of igneous rock overlies sedimentary rock to form a cuesta with both rock types exposed along a steep ridge flank. Field studies investigating the near‐surface hydrogeologic properties of the caprocks at several of these sites have reported a narrow range of results; some fractured rocks form modest aquifers whereas others do not. To examine this behavior in terms of geomechanical responses to gravitational stresses imposed near ridges, a finite‐element model is presented that incorporates the geometry of a ridge‐valley configuration and its major structural elements. Model simulations reflect the effects of a lack of buttressing along free faces and a contrast in Poisson's ratios between the superposed igneous and sedimentary rocks. Three‐dimensional Mohr's circles are constructed from principal stress magnitudes and directions to evaluate the response of individual fracture planes to this stress state. Results depict a predominantly tensional stress environment where numerous pre‐existing fractures may be favorably aligned for opening and enhanced caprock permeability. However, the lack of conclusive field evidence to support this hypothesis suggests that the in situ tensile strength of the fractured rock mass is substantial enough to resist failure by shear or dilation, and that critically‐stressed fracture planes do not convey large volumes of groundwater in ridge‐valley settings.

Conference Paper↗

USGS2010

The influence of topology on hydraulic conductivity in a sand-and-gravel aquifer

A field experiment consisting of geophysical logging and tracer testing was conducted in a single well that penetrated a sand‐and‐gravel aquifer at the U.S. Geological Survey Toxic Substances Hydrology research site on Cape Cod, Massachusetts. Geophysical logs and flowmeter/pumping measurements were obtained to estimate vertical profiles of porosity ϕ, hydraulic conductivity K , temperature, and bulk electrical conductivity under background, freshwater conditions. Saline‐tracer fluid was then injected into the well for 2 h and its radial migration into the surrounding deposits was monitored by recording an electromagnetic‐induction log every 10 min. The field data are analyzed and interpreted primarily through the use of Archie's (1942) law to investigate the role of topological factors such as pore geometry and connectivity, and grain size and packing configuration in regulating fluid flow through these coarse‐grained materials. The logs reveal no significant correlation between K and ϕ, and imply that groundwater models that link these two properties may not be useful at this site. Rather, it is the distribution and connectivity of the fluid phase as defined by formation factor F , cementation index m , and tortuosity α that primarily control the hydraulic conductivity. Results show that F correlates well with K , thereby indicating that induction logs provide qualitative information on the distribution of hydraulic conductivity. A comparison of α, which incorporates porosity data, with K produces only a slightly better correlation and further emphasizes the weak influence of the bulk value of ϕ on K .

Massachusetts↗

USGS2009

Geophysical log analysis of selected test holes and wells in the High Plains Aquifer, Central Platte River Basin, Nebraska

The U.S. Geological Survey in cooperation with the Central Platte Natural Resources District is investigating the hydrostratigraphic framework of the High Plains aquifer in the Central Platte River basin. As part of this investigation, a comprehensive set of geophysical logs was collected from six test holes at three sites and analyzed to delineate the penetrated stratigraphic units and characterize their lithology and physical properties. Flow and fluid-property logs were collected from two wells at one of the sites and analyzed along with the other geophysical logs to determine the relative transmissivity of the High Plains aquifer units. The integrated log analysis indicated that the coarse-grained deposits of the alluvium and the upper part of the Ogallala Formation contributed more than 70 percent of the total transmissivity at this site. The lower part of the Ogallala with its moderately permeable sands and silts contributed some measureable transmissivity, as did the fine-grained sandstone of the underlying Arikaree Group, likely as a result of fractures and bedding-plane partings. Neither the lower nor the upper part of the siltstone- and claystone-dominated White River Group exhibited measurable transmissivity. The integrated analysis of the geophysical logs illustrated the utility of these methods in the detailed characterization of the hydrostratigraphy of the High Plains aquifer.

Nebraska↗

USGS2007

Hydrogeologic controls imposed by mechanical stratigraphy in layered rocks of the Chateauguay River Basin, a U.S.-Canada transborder aquifer

[1] The Châteauguay River Basin delineates a transborder watershed with roughly half of its surface area located in northern New York State and half in southern Québec Province, Canada. As part of a multidisciplinary study designed to characterize the hydrogeologic properties of this basin, geophysical logs were obtained in 12 wells strategically located to penetrate the four major sedimentary rock formations that constitute the regional aquifers. The layered rocks were classified according to their elastic properties into three primary units: soft sandstone, hard sandstone, and dolostone. Downhole measurements were analyzed to identify fracture patterns associated with each unit and to evaluate their role in controlling groundwater flow. Fracture networks are composed of orthogonal sets of laterally extensive, subhorizontal bedding plane partings and bed-delimited, subvertical joints with spacings that are consistent with rock mechanics principles and stress models. The vertical distribution of transmissive zones is confined to a few select bedding plane fractures, with soft sandstone having the fewest (one per 70-m depth) and hard sandstone the most (five per 70-m depth). Bed-normal permeability is examined using a probabilistic model that considers the lengths of flow paths winding along joints and bedding plane fractures. Soft sandstone has the smallest bed-normal permeability primarily because of its wide, geomechanically undersaturated joint spacing. Results indicate that the three formations have similar values of bulk transmissivity, within roughly an order of magnitude, but that each rock unit has its own unique system of groundwater flow paths that constitute that transmissivity.

Chateauguay River Basin↗

USGS2007

Site Report for USGS Test Holes Drilled at Cape Charles, Northampton County, Virginia, in 2004

The U.S. Geological Survey drilled two test holes near Cape Charles, Virginia, during May and June 2004, as part of an investigation of the buried, late Eocene Chesapeake Bay impact structure. The first hole is designated as the USGS-Sustainable Technology Park test hole #1 (USGS-STP1). This test hole was abandoned at a depth of 300 ft; cuttings samples were collected, but no cores or geophysical logs were acquired. The second hole is designated as the USGS-Sustainable Technology Park test hole #2 (USGS-STP2). This test hole was drilled to a depth of 2,699 ft. Cores were collected between depths of 1,401.7 ft and 1,420.7 ft and between 2,440.0 ft and 2,699.0 ft. Cuttings samples were collected from the uncored intervals below 280-ft depth. Interim sets of geophysical logs were acquired during the drilling operation, and one final set was acquired at the end of drilling. Two wells were installed in the USGS-STP2 test hole. The deep well (designated 62G-24) was screened between 2,260 ft and 2,280 ft, and the shallow well (designated 62G-25) was screened between 1,360 ft and 1,380 ft. Ground-water salinities stabilized at 40 parts per thousand for the deep well and 20 parts per thousand for the shallow well. The geologic section encountered in the test holes consists of three main units: (1) Eocene, Oligocene, Miocene, Pliocene, and Pleistocene sands and clays are present between land surface and a depth of 1,163 ft; (2) sediment-clast breccias of the impact structure are present between depths of 1,163 ft and 2,150 ft; and (3) crystalline-clast breccias and cataclastic gneiss of the impact structure are present between depths of 2,150 ft and 2,699 ft.

Open-File Report↗

USGS2007

Questa baseline and pre-mining ground-water quality investigation 15.—Methods of phase II and III well installation and development and results of well logging, hydraulic testing, and water-level measurements in the Red River Valley, New Mexico, 2002-04

In April 2001, the U.S. Geological Survey and the New Mexico Environment Department began a cooperative study to infer the pre-mining ground-water chemistry at the Molycorp molybdenum mine site in the Red River Valley of north- central New Mexico. This report is one in a series of reports that can be used to determine pre-mining ground-water conditions at the mine site. Weathering of hydrothermally altered bedrock in the study area has resulted in steep, highly erosive, and sparsely vegetated scar areas that are clearly visible from the ground and in aerial photographs. Runoff from intense summer rainfall over tributary drainages containing scar areas can transport large quantities of sediment and form debris fans where these tributaries join the Red River. Twenty-nine observation wells were installed in three phases as part of this study in the Red River Valley and tributary drainages. Eight Phase II observation wells were drilled using an air-rotary/hammer rig. Three Phase II and 10 phase III small-diameter wells were installed using a direct-push rig. Lithologic logs were recorded for all eight Phase II drilled wells. Borehole geophysical logging (including natural gamma, induction, and single-detector neutron) was conducted in three Phase II wells. Aquifer tests conducted during 2003 to estimate the hydraulic properties of debris-flow and Red River alluvial deposits in and near Straight Creek included a flow-meter survey, slug tests, and a pumping test. Results of a flow-meter survey in well SC-7A indicated that about 77 percent of the water entered the well from a 10-foot-thick zone near the top of the screened interval and about 23 percent of the water entered the well from a 15-foot-thick zone near the bottom of the screened interval. Slug tests, performed in 11 wells during June 3-5, 2003, indicated that the mean and median estimated hydraulic conductivities for debris-flow deposits were 15.25 and 15.35 feet per day, respectively, for bedrock were 0.12 and 0.08 feet per day, respectively, and for mixed debris flow and Red River alluvium were 73-207 (estimated range) and 80 feet per day. In general, bedrock has the smallest hydraulic conductivity, debris-flow material has the next highest hydraulic conductivity, and mixed debris flow and Red River alluvium has the largest hydraulic conductivity. A pumping test conducted December 3-4, 2003, using well AWWT-1 as the pumped well, and wells AWWT-2, SC-5A, SC-5B, SC-7A, and SC-8A as observation wells, indicated estimated transmissivity of 12,000 to 34,000 feet squared per day and estimated hydraulic conductivity of 230 to 340 feet per day. Water-level measurements in wells SC-6A, SC-7A, SC-8A, and the Hottentot, Hansen, and La Bobita wells show that water levels typically rose rapidly during melting of the winter snowpack in the springtime and then generally declined during the rest of the year. The water-level rise in response to spring snowmelt occurred earlier and was smaller at larger distances from the Red River. Differences between the stage in the Red River and water levels in wells SC-8A and SC-9A, and the absence of water in well SC-9A at the time of well completion, indicate that the Red River has a poor hydraulic connection to the underlying ground-water system and the surface-water system is perched above the ground-water system at this site. Water levels in Phase III wells indicate that the Red River and the shallow ground-water system are connected hydraulically from near wells 4-1D and 4-1S downstream to near wells 2-1 and 2-2 but are poorly connected near the La Bobita well and well 1.

New Mexico↗

USGS2006

Determining the distribution of hydraulic conductivity in a fractured limestone aquifer by simultaneous injection and geophysical logging

A field technique for assessing the vertical distribution of hydraulic conductivity in an aquifer was applied to a fractured carbonate formation in southeastern Nevada. The technique combines the simultaneous use of fluid injection and geophysical logging to measure in situ vertical distributions of fluid velocity and hydraulic head down the borehole; these data subsequently are analyzed to arrive at quantitative estimates of hydraulic conductivity across discrete intervals in the aquifer. The results of this analysis identified the contact margin between the Anchor and Dawn Members of the Monte Cristo Limestone as being the dominant transmissive unit. -from Authors

Nevada↗

USGS2005

Fractured-aquifer hydrogeology from geophysical logs: Brunswick group and Lockatong Formation, Pennsylvania

The Brunswick Group and the underlying Lockatong Formation are composed of lithified Mesozoic sediments that constitute part of the Newark Basin in southeastern Pennsylvania. These fractured rocks form an important regional aquifer that consists of gradational sequences of shale, siltstone, and sandstone, with fluid transport occurring primarily in fractures. An extensive suite of geophysical logs was obtained in seven wells located at the borough of Lansdale, Pennsylvania, in order to better characterize the areal hydrogeologic system and provide guidelines for the refinement of numerical ground water models. Six of the seven wells are approximately 120 m deep and the seventh extends to a depth of 335 m. Temperature, fluid conductivity, and flowmeter logs are used to locate zones of fluid exchange and to quantify transmissivities. Electrical resistivity and natural gamma logs together yield detailed stratigraphic information, and digital acoustic televiewer data provide magnetically oriented images of the borehole wall from which almost 900 fractures are identified. Analyses of the geophysical data indicate that the aquifer penetrated by the deep well can be separated into two distinct structural domains, which may, in turn, reflect different mechanical responses to basin extension by different sedimentary units: 1. In the shallow zone (above 125 m), the dominant fracture population consists of gently dipping bedding plane partings that strike N46°E and dip to the northwest at about 11 degrees. Fluid flow is concentrated in the upper 80 m along these subhorizontal fractures, with transmissivities rapidly diminishing in magnitude with depth. 2. The zone below 125 m marks the appearance of numerous high-angle fractures that are orthogonal to the bedding planes, striking parallel but dipping steeply southeast at 77 degrees. This secondary set of fractures is associated with a fairly thick (approximately 60 m) high-resistivity, low-transmissivity sandstone unit that is abruptly terminated by a thin shale bed at a depth of 190 m. This lower contact effectively delineates the aquifer's vertical extent at this location because no detectable evidence of ground water movement is found below it. Thus, fluid flow is controlled by fractures, but fracture type and orientation are related to lithology. Finally, a transient thermal-conduction model is successfully applied to simulate observed temperature logs, thereby confirming the effects of ground-surface warming that occurred in the area as a result of urbanization at the turn of the century. The systematic warming of the upper 120 m has increased the transmissivity of this aquifer by almost 10%, simply due to changes in fluid viscosity and density.

Pennsylvania↗

USGS2005

Questa baseline and pre-mining ground-water quality investigation. 5. Well installation, water-level data, and surface- and ground-water geochemistry in the Straight Creek drainage basin, Red River Valley, New Mexico, 2001-03

The U.S. Geological Survey, in cooperation with the New Mexico Environment Department, is investigating the pre-mining ground-water chemistry at the Molycorp molybdenum mine in the Red River Valley, northern New Mexico. The primary approach is to determine the processes controlling ground-water chemistry at an unmined, off-site, proximal analog. The Straight Creek drainage basin, chosen for this purpose, consists of the same quartz-sericite-pyrite altered andesitic and rhyolitic volcanic rock of Tertiary age as the mine site. The weathered and rugged volcanic bedrock surface is overlain by heterogeneous debris-flow deposits that interfinger with alluvial deposits near the confluence of Straight Creek and the Red River. Pyritized rock in the upper part of the drainage basin is the source of acid rock drainage (pH 2.8-3.3) that infiltrates debris-flow deposits containing acidic ground water (pH 3.0-4.0) and bedrock containing water of circumneutral pH values (5.6-7.7). Eleven observation wells were installed in the Straight Creek drainage basin. The wells were completed in debris-flow deposits, bedrock, and interfingering debris-flow and Red River alluvial deposits. Chemical analyses of ground water from these wells, combined with chemical analyses of surface water, water-level data, and lithologic and geophysical logs, provided information used to develop an understanding of the processes contributing to the chemistry of ground water in the Straight Creek drainage basin. Surface- and ground-water samples were routinely collected for determination of total major cations and selected trace metals; dissolved major cations, selected trace metals, and rare-earth elements; anions and alkalinity; and dissolved-iron species. Rare-earth elements were determined on selected samples only. Samples were collected for determination of dissolved organic carbon, mercury, sulfur isotopic composition (34S and 18O of sulfate), and water isotopic composition (2H and 18O) during selected samplings. One set of ground-water samples was collected for helium-3/tritium and chlorofluorocarbon (CFC) age dating. Several lines of evidence indicate that surface water is the primary input to the Straight Creek ground-water system. Straight Creek streamflow and water levels in wells closest to the apex of the Straight Creek debris fan and closest to Straight Creek itself appear to respond to the same seasonal inputs. Oxygen and hydrogen isotopic compositions in Straight Creek surface water and ground water are similar, and concentrations of most dissolved constituents in most Straight Creek surface-water and shallow (debris-flow and alluvial) aquifer ground-water samples correlate strongly with sulfate (concentrations decrease linearly with sulfate in a downgradient direction). After infiltration of surface water, dilution along the flow path is the dominant mechanism controlling ground-water chemistry. However, concentrations of some constituents can be higher in ground water than can be accounted for by concentrations in Straight Creek surface water, and additional sources of these constituents must therefore be inferred. Constituents for which concentrations in ground water can be high relative to surface water include calcium, magnesium, strontium, silica, sodium, and potassium in ground water from debris-flow and alluvial aquifers and manganese, calcium, magnesium, strontium, sodium, and potassium in ground water from the bedrock aquifer. All ground water is a calcium sulfate type, often at or near gypsum saturation because of abundant gypsum in the aquifer material developed from co-existing calcite and pyrite mineralization. Calcite dissolution, the major buffering mechanism for bedrock aquifer ground water, also contributes to relatively higher calcium concentrations in some ground water. The main source of the second most abundant cation, magnesium, is probably dissolution of magnesium-rich carbonates or silicates.

New Mexico↗

USGS1996

Analysis of fractures intersecting Kahi Puka Well 1 and its relation to the growth of the island of Hawaii

As part of the Hawaii Scientific Drilling Project, Kahi Puka Well 1 penetrated about 275 m of Mauna Loa basalts overlying a sequence of Mauna Kea flow units as it was drilled and cored to a total depth of 1053 m below land surface. A borehole televiewer (BHTV) was run in most of the well in successive stages prior to casing in order to obtain magnetically oriented acoustic images of the borehole wall. A total of 283 individual fractures were identified from this log and characterized in terms of strike and dip. These data are divided into three vertical sections based upon age and volcanic source, and lower hemisphere stereographic plots identify two predominant, subparallel fracture subsets common to each section. Assuming that most of the steeply dipping fractures observed in the BHTV log are tensile features generated within basalt flows during deposition and cooling, this fracture information can be combined with models of the evolution of the island of Hawaii to investigate the depositional history of these Mauna Loa and Mauna Kea basalts over the past 400 kyr. The directions of high-angle fractures appear to be generally parallel to topography or to the coastline at the time of deposition, as is supported by surface mapping of modern flows. Consequently, an overall counterclockwise rotation of about 75?? in the strike of these fractures from the bottom to the top of the well represents a systematic change in depositional slope direction over time. We attribute the observed rotation in the orientations of the two predominant fracture subsets over the past 400 kyr to changes in the configurations of volcanic sources during shield building and to the structural interference of adjacent volcanoes that produces shifts in topographic patterns.

Journal of Geophysical Research B: Solid Earth↗

USGS1995

Hydrostatigraphic characterization of coastal aquifer by geophysical log analysis, Cape Cod National Seashore, Massachusetts

The Cape Cod National Seashore comprises part of Provincetown, Massachusetts, which lies at the northern tip of Cape Cod. The hydrologic regime in this area consists of unconsolidated sand-and-gravel deposits that constitute a highly permeable aquifer within which is a freshwater lens floating on denser sea water. A network of wells was installed into this aquifer to monitor a leachate plume emanating from the Provincetown landfill. Wells were located along orthogonal transects perpendicular to and parallel to the general groundwater flow path from the landfill to the seashore approximately 1,000 m to the southeast. Temperature, epithermal neutron, natural gamma. and electronmagnetic induction logs were obtained in five wells to depths ranging from 23 to 37 m. These logs identify the primary contamination and show that its movement is controlled by and confined within a dominant hydrostratigraphic unit about 2 to 5 m thick that exhibits low porosity, large representative grain size, and high relative permeability. A relation is also found between the temperaturegradient logs and water quality, with the gradient traces serving as effective delineators of the contaminant plume in wells nearest the landfill. Contamination is not detectable in the well nearest the seashore and farthest from the landfill, and the induction log from this well clearly identifies the freshwater/seawater transition zone at a depth of about 18 m. The geophysical logs provide fundamental information concerning the spatial distribution of aquifer properties near the landfill and lend valuable insight into how these properties influence the migration of the leachate plume to the sea.

Log Analyst↗

USGS1989

Graphical method for determining the coefficient of consolidation c from a flow-pump permeability test

A graphical method has been developed for determining the coefficient of consolidation from the transient phases of a flow-pump permeability test. The flow pump can be used to infuse fluid into or withdraw fluid from a laboratory sediment specimen at a constant volumetric rate in order to obtain data that can be used to calculate permeability using Darcy's law. When the initial transient-response curve (hydraulic head as a function of time) generated by this test is examined analytically in terms of a one-dimensional consolidation process, representative type-curve solutions to the associated forced-flow and pressure-decay models are derived. These curves provide the basis for graphically evaluating the permeability k , the coefficient of consolidation c v , and the coefficient of volume change m v . The curve-matching technique is easy and rapid, and it can be applied to results of forced-flow tests, both infusion and withdrawal, as well as to subsequent pressure-decay records. Values of k, c v , and m v for a laterally confined kaolinite specimen were determined by this graphical method and appear to be in reasonably good agreement with numerically derived estimates (within 20%). Discrepancies between the two sets of results seem to be largely a function of data quality rather than of method of analysis. Where responses of hydraulic head as a function of time are apparently unaffected by experimental sources of error, agreement is excellent (within 4%). Application of this graphical method to triaxial testing has inherent uncertainties, because the solution curves that describe one-dimensional deformation are used to analyze a three-dimensional process.

Geotechnical Testing Journal↗