USGS Science⌕ Search

Geology topics

Robert J. Bisdorf

Publications and source records attributed to Robert J. Bisdorf.

At least 19 recordsLinked to original sources
USGS2004

Results of Electrical Resistivity Data Collected near the Town of Guernsey, Platte County, Wyoming

As part of a study to investigate subsurface geologic conditions as they relate to ground-water flow in an abandoned landfill near the town of Guernsey, Wyoming, geophysical direct current (DC) resistivity data were collected. Eight vertical resistivity soundings and eight horizontal resistivity profiles were made using single channel and multi-channel DC instruments. Data collected in the field were converted from apparent resistivity to inverted resistivity with depth using a numerical inversion of the data. Results of the inverted resistivity data are presented as horizontal profiles and as profiles derived from the combined horizontal profile and vertical sounding data. The data sets collected using the single-channel and multi-channel DC systems provided for the resistivity investigation to extend to greater depth. Similarity of the electrical properties of the bedrock formations made interpretation of the resistivity profiles more difficult. High resistivity anomalies seen in the profiles are interpreted as quartzite lenses and as limestone or metadolomite structures in the eastern part of the study area. Terrace gravels were mapped as resistive where dry and less resistive in the saturated zone. The DC resistivity methods used in this study illustrate that multi-electrode DC resistivity surveying and more traditional methodologies can be merged and used to efficiently map anomalies of hydrologic interest in geologically complex terrain.

Open-File Report↗
USGS2002

Schlumberger soundings at the Amargosa Desert Research Site, Nevada

In 1999 the U.S. Geological Survey made 38 direct current (dc) electrical soundings at the Amargosa Desert Research Site (ADRS) near Beatty, Nevada (fig. 1.) using the Schlumberger array. An additional 16 Schlumberger soundings were made in 2000. The soundings were made to determine the subsurface resistivity distribution, and the location of faults. The purpose of this report is to present the data, its automatic interpretation, cross sections and resistivity depth maps. Figure 2 is a map of the sounding locations. The soundings are represented by circles. The 1999 data are numbered 1 through 38 and the 2000 data are numbered 101 through 116. Table 1 gives the sounding number, x coordinate, and y coordinate of the soundings in UTM zone 11 NAD27.

Nevada↗
USGS2002

Preliminary geophysical characterization of two oil production sites, Osage County, Oklahoma - Osage Skiatook Petroleum Environmental Research Project

Ground electromagnetic and dc resistivity geophysical surveys were used to interpret the subsurface distribution of salinized soil, water, and bedrock at two sites (A and B) and to characterize the larger scale hydrologic setting. Measurements were made on grids of about 1000 square meters using a very shallow penetrating (less than 10 m) electromagnetic (EM) geophysical system (EM31). At site A, high subsurface conductivities (more than 100 millisiemens per meter) found below disposal ponds extended down the local hydrologic gradient to below the normal level of near by Lake Skiatook. At site B, areas of highest subsurface electrical conductivity were offset about 10 m from the center of salt scars. The area of high subsurface electrical conductivity extends in the subsurface below the normal level of Skiatook Lake. DC resistivity soundings were made in and around the two sites in order to characterize deeper (30-60 m) electrical properties of the subsurface lithology and ground water. These soundings indicate that the tight shale that dominates the local lithology is moderately electrically conductive (5 milliseimems per meter). DC soundings done in several areas at the Skiatook Lake shoreline indicate an electrically conductive (less than 10 millisiemens per meter) zone exists below the shore even away from the oil production sites. This conductive zone may indicate a mixing between fresh lake water and local ground water that has high dissolved solids. Borehole geophysical logs at site B and laboratory rock property measurements are currently being used to refine interpretation of ground geophysical measurements.

Oklahoma↗
USGS1985

Electrical Techniques for Engineering Applications

Surface electrical geophysical methods have been used in such engineering applications as locating and delineating shallow gravel deposits, depth to bedrock, faults, clay zones, and other geological phenomena. Other engineering applications include determining water quality, tracing ground water contaminant plumes and locating dam seepages. Various methods and electrode arrays are employed to solve particular geological problems. The sensitivity of a particular method or electrode array depends upon the physics on which the method is based, the array geometry, the electrical contrast between the target and host materials, and the depth to the target. Each of the available electrical methods has its own particular advantages and applications which the paper discusses.

Bulletin of the Association of Engineering Geologi↗